Pasar al contenido principal

DISEÑO OPTIMO DE INSTALACIONES Y SISTEMAS ENERGETICOS OFF-SHORE MEDIANTE TECNICAS DE MECANICA COMPUTACIONAL DE ALTA PRECISION

DPI2015-68431-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDADE DA CORUÑA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Topology optimization of structures considering minimum weight and stress constraints by using the Overweight Approach

  • Villalba Rama, Diego
  • París, José
  • Couceiro, Iván
  • Colominas, Ignasi
  • Navarrina, Fermín
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract:] In this paper, a new method for structural topology optimization considering minimum weight and local stress constraints is proposed. For this purpose, the Overweight Approach, an improvement of the so-called Damage Approach, is used. In this method, a virtual relative density is defined as a function of the violation of the local stress constraints. The virtual relative density is increased as stresses exceed the maximum allowable value. The optimization algorithm will provide a design with a minimal variation of the relative density. The structural analysis is performed by means of the Finite Element Method (FEM) and the distribution of material is modelled in terms of a uniform relative density within each element. Moreover, the optimization is addressed by means of the Sequential Linear Programming algorithm (SLP). Finally, the proposed methodology is tested by means of some benchmark problems, and the results show that the Overweight Approach is a feasible alternative for the Damage Approach and the stress constraint aggregation techniques., Xunta de Galicia; ED481A-2016/387, Xunta de Galicia; GRC2014/039, Xunta de Galicia; GRC2018/41, This work has been partially supported by the “Xunta de Galicia, Spain (Secretaría Xeral de Universidades)” and the European Union (European Social Fund - ESF) through “Grants for supporting the predoctoral stage in universities of the Galician University System, in research public organisms of Galicia and in other entities of the “R & D system of the Galician Government - 2016” ED481A-2016/387, by Feder funds of the European Union, by the “Ministerio de Economía y Competitividad, Spain” of the Spanish Government through grants DPI2015-68431-R and RTI2018-093366-B-I00, by the “Consellería de Educación, Universidade e Formación Profesional, Spain” of the “Xunta de Galicia” through “grants for the consolidation and structuring of competitive research units of the Galician University System: Competitive reference group” GRC2014/039 and GRC2018/41, and by research fellowships of the University of A Coruña, Spain and the “Fundación de la Ingeniería Civil de Galicia, Spain ”.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

A Higher‑Order Chimera Method for Finite Volume Schemes

  • Ramírez, Luis
  • Nogueira, Xesús
  • Ouro, Pablo
  • Navarrina, Fermín
  • Khelladi, Sofiane
  • Colominas, Ignasi
Versión aceptada de https://doi.org/10.1007/s11831-017-9213-8, [Abstract:] In this work a higher-order accurate finite volume method for the resolution of the Euler/Navier–Stokes equations using Chimera grid techniques is presented. The formulation is based on the use of Moving Least Squares approximations in order to obtain higher-order accurate reconstruction and connectivity between the overlapped grids. The accuracy and performance of the proposed methodology is demonstrated by solving different benchmark problems., This work has been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) of the Spanish Government and by the Consellería de Educación e Ordenación Universitaria of the Xunta de Galicia (grant #GRC2014/039), cofinanced with FEDER funds and the Universidade da Coruña., Xunta de Galicia; GRC2014/039
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Numerical Analysis and Safety Design of Grounding Systems in Underground Compact Substations

  • Guizán Roca, Raquel
  • Colominas, Ignasi
  • París, José
  • Couceiro, Iván
  • Navarrina, Fermín
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] This paper presents a mathematical and numerical formulation to design and analyze grounding systems in underground electrical substations. The developed approach is based on the well known Maxwell’s Equations. The proposed problem is solved by means of the Boundary Element Method (BEM). The utilization of BEM allows to introduce the geometry and electrical characteristics of the enclosure in a uniform soil. Therefore, a more realistic approximation of the soil structure is achieved. This formulation allows to obtain the main parameters of these protection systems (the grid resistance, the Ground Potential Rise, and the step and mesh voltage). It also allows to compute the surface and step voltage distributions. In addition, as a secondary result, the voltage and current density distributions over the enclosure are obtained. Finally, two grounding system analyses of real underground electrical substations are presented to demonstrate the industrial application and the modelization capabilities of the proposed formulation., This work has been partially supported by the “Consellería de Cultura, Educación e Ordenación Universitaria” of the “Xunta de Galicia” (grant GRC2014/039) and (grant ED431C2018/41), by the “Ministerio de Economía y Competitividad” (grant DPI2015-68431R) and "Ministerio de Ciencia, Innovación y Universidades" (grant RTI2018-093366-B-I00). Funding for open access charge: Universidade da Coruña/CISUG, Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431C2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Estimation of long-term fatigue damage of fixed substructures using fully-coupled models and non-linear dynamic analysis

  • Couceiro, Iván
  • París, José
  • Navarrina, Fermín
  • Colominas, Ignasi
  • Ramírez, Luis
Versión aceptada de https://doi.org/10.1016/j.oceaneng.2020.107284, [Abstract:] Typical industry models for Offshore Wind Turbines with fixed substructures are based on decoupled models between the wind turbine and the substructure. It is proved that the complete dynamic response of the structure can only be captured with coupled models. In this paper a fully-coupled model for Offshore Wind Turbines with jacket support is presented. The computational model allows to obtain an accurate response of the whole structure and the dynamic interaction between all the elements. It also allows to reproduce particular effects such as the aerodynamic damping without the need for artificial damping ratios which would be needed in decoupled models. Typical environmental offshore conditions are integrated in the model and the response of the structure is obtained by means of a non-linear time integration algorithm in order to include the effect of the continuous rotation of the blades. A cost-efficient approach for the determination of fatigue-damage in the joints of the jackets is proposed. It is based on short-time simulations which allow to accurately estimate the long-term damage in general. The estimation shows a good agreement when compared to the damage values obtained by performing the whole time-interval simulation., This work has been partially supported by FEDER funds of the European Union, by the Ministerio de Economía y Competitividad of the Spanish Goverment through grant # DPI2015-68431-R and grant # RTI2018-093366-B-100, by the Secretaría Xeral de Universidades of the Xunta de Galicia through grants # GRC2014/039 and # ED431C 2018/41, by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia by a grant awarded to the University of A Coruña, and by research fellowships of the University of A Coruña and the Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431C 2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Tesis doctoral (DoctoralThesis)

Impact of Dynamic Axle Loading on the Service Life of Flexible Pavements

  • Ruiz, Manuel
[Abstract] Impact of dynamic axle loading on the service life of flexible pavements The study of pavement maintenance strategies has gained great importance in recent years, both because of the drastic decrease in investments for the maintenance of road infrastructures and because of the benefits associated with the performance of such preventive maintenance. This doctoral thesis uses a methodology focused on the study of the impact of preventive maintenance strategies on the service life of flexible pavements, taking into account the effect of dynamic rolling loads. The first part of the methodology focuses on calculating the fatigue failure of a flexible pavement considering the effect of dynamic axle loads. For this purpose, a multilayer elastic model is first developed to calculate the mechanical responses of the firm. Then, a structural failure model of the pavement and its fatigue failure criteria are defined. The second part of the methodology focuses on the role of dynamic axle loads in the fatigue failure of the pavement. First, the methodology for calculating these dynamic axle loads using a quarter heavy vehicle model is presented, which requires the computational simulation of a longitudinal road profile. Finally, a deterioration model of surface evenness is presented, thanks to which it is possible to simulate the time evolution of this surface evenness, and therefore, the time evolution of the dynamic axle loads during the pavement service life. Finally, the algorithm used is presented, as well as the reduced model of this algorithm and its implementation in a software that allows to calculate the effect of different preventive maintenance strategies on the service life of a flexible pavement., [Resumen] Impacto de las cargas dinámicas en la vida útil de firmes flexibles El estudio de las estrategias de conservación de firmes ha cobrado gran importancia en los últimos años, tanto por el descenso drástico en las inversiones para el mantenimiento de las infraestructuras viarias como por los beneficios asociados a la realización de dicho mantenimiento preventivo. En la presente tesis doctoral se desarrolla una metodología centrada en el estudio del impacto sobre la vida útil de firmes flexibles de las estrategias de mantenimiento preventivo, teniendo en cuenta el efecto de las cargas dinámicas de rodadura. La primera parte de la metodología empleada se centra en calcular el fallo a fatiga de un firme flexible considerando el efecto de las cargas dinámicas de rodadura. Para dicho fin, primeramente se desarrolla un modelo elástico multicapa para calcular las respuestas mecánicas del paquete de firme. A continuación se define un modelo de comportamiento de dicho paquete de firme y su criterio de fallo por fatiga. La segunda parte de la metodología se centra en el papel que desempeñan las cargas dinámicas de rodadura en el fallo por fatiga del paquete de firme. En primer lugar se presenta la metodología para calcular dichas cargas dinámicas de rodadura empleando un modelo de cuarto de vehículo pesado, la cual requiere de la simulación computacional de un perfil longitudinal de carretera. Finalmente se presenta un modelo de deterioración de regularidad superficial, gracias al cual se puede simular la evolución temporal de dicha regularidad superficial, y por lo tanto, la evolución temporal de las cargas dinámicas de rodadura durante la vida ´útil del firme. Finalmente se presenta el algoritmo empleado, así como el modelo reducido de dicho algoritmo y su implementación en un software que permite calcular el efecto de diferentes estrategias de mantenimiento preventivo en la vida útil de un firme flexible., [Resumo] Impacto das cargas dinámicas na vida útil dos pavimentos flexíbeis O estudo das estratexias de conservación de firmes cobrou gran importancia nos últimos anos, tanto polo declive drástico nos investimentos para o mantemento das infrastructuras viarias coma polos beneficios asociados á realización de dito mantemento preventivo. Na presente tese doutoral lévasne a cabo unha metodoloxía centrada no estudo do impacto sobre a vida útil dos firmes flexíbeis das estratexias de mantemento preventivo, tendo en conta o efecto das cargas dinámicas de rodadura. A primeira parte da metodoloxía empregada céntrase en calcular o fallo a fatiga dun firme flexíbel considerando o efecto das cargas dinámicas de rodadura. Para dito fin, primeiramente desenvólvese un modelo elástico multicapa para calcular as respostas mecánicas do paquete de firme. Deseguido defínese un modelo de comportamento deste paquete de firme e o seu criterio de fallo por fatiga. A segunda parte da metodoloxía céntrase no papel que desempeñan as cargas dinámicas de rodadura no fallo por fatiga do paquete de firme. En primeiro lugar preséntase a metodoloxía para calcular ditas cargas dinámicas de rodadura empregando un modelo de cuarto de vehículo pesado, a cal require da simulación computacional dun perfil lonxitudinal de estrada. Finalmente preséntase un modelo de deterioración de regularidade superficial, grazas ao cal pódese simular a evolución temporal de dita regularidade superficial, e polo tanto, a evolución temporal das cargas dinámicas de rodadura durante a vida útil do firme. Finalmente preséntase o algoritmo empregado, así como o modelo reducido deste algoritmo e a súa implementación nun software que permite calcular o efecto de diferentes estratexias de mantemento preventivo na vida útil dun firme flexíbel., This work has been primarily supported by the European Investment Bank (EIB) Institute through a STAREBEI grant awarded to the Fundaci´on de la Ingeniería Civil de Galicia. Partial support has also been provided by FEDER funds of the European Union, by the Ministerio de Economía y Competitividad of the Spanish Government through grant #DPI2015-68431-R, by the Ministerio de Ciencia, Innovación y Universidades of the Spanish Government through grant #RTI2018-093366-BI00, by the Secretaría Xeral de Universidades of the Xunta de Galicia through grants GRC2014/039 and # ED431C 2018/41, by the Conselleria de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia through a grant awarded to the University of A Coru˜na, and by research fellowships of the University of A Coruña and the Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; ED431C 2018/41, Xunta de Galicia; GRC2014/039
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Very high-order method on immersed curved domains for finite difference schemes with regular Cartesian grids

  • Fernández-Fidalgo, Javier
  • Nogueira, Xesús
  • Ramírez, Luis
  • Colominas, Ignasi
  • Clain, Stéphane
Versión aceptada de https://doi.org/10.1016/j.cma.2019.112782, [Abstract:] A new very high-order technique for solving conservation laws with curved boundary domains is proposed. A Finite Difference scheme on Cartesian grids is coupled with an original ghost cell method that provide accurate approximations for smooth solutions. The technology is based on a specific least square method with restrictions that enables to handle general Robin conditions. Several examples in two-dimensional geometries are presented for the unsteady Convection–Diffusion equation and the Euler equations. A fifth-order WENO scheme is employed with matching fifth-order reconstruction at the boundaries. Arbitrary high-order reconstruction for smooth flows is achievable independently of the underlying differential equation since the method works as a black-box dedicated to boundary condition treatment., This work has been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) and #RTI2018-093366-B-I00 of the Ministerio de Ciencia, Innovación y Universidades of the Spanish Government and by the Consellería de Educación e Ordenación Universitaria of the Xunta de Galicia (grants #GRC2014/039 and #ED431C 2018/41), cofinanced with FEDER, Spain funds and the Universidade da Coruña, Spain. J. Fernandez-Fidalgo gratefully acknowledges the contributions of the IACOBUS Program, Spain and the INDITEX-UDC, Spain grant that have partially financed the present work. S. Clain acknowledges the financial support by FEDER – Fundo Europeu de Desenvolvimento Regional, Portugal, through COMPETE 2020 – Programa Operational Fatores de Competitividade, and the National Funds through FCT — Fundação para a Ciência e a Tecnologia, Portugal , project No. UID/FIS/04650/2013 and project No. POCI-01-0145-FEDER-028118., Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431C 2018/41, Fundação para a Ciência e a Tecnologia (Portugal); UID/FIS/04650/2013, Fundação para a Ciência e a Tecnologia (Portugal); POCI-01-0145-FEDER-028118
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

A very accurate Arbitrary Lagrangian–Eulerian meshless method for Computational Aeroacoustics

  • Nogueira, Xesús
  • Ramírez, Luis
  • Colominas, Ignasi
  • Khelladi, Sofiane
  • Krimi, Abdelkader
Versión aceptada de https://doi.org/10.1016/j.cma.2018.07.036, [Abstract:] In this work, we propose a new meshless approach based on a Galerkin discretization of a set of conservation equations on an Arbitrary Lagrangian–Eulerian framework. In particular, we solve the Linearized Euler Equations, using Moving Least Squares as weight functions in the Galerkin discretization. Riemann solvers are introduced in the formulation for the discretization of the convective fluxes. Differently from a purely Lagrangian approach, as it is usual in SPH, the present method is able to work in both Eulerian and Lagrangian configurations, which allows using all the advantages of the Lagrangian approaches in the context of Computational Aeroacoustics., This work has been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) of the Spanish Government and by the Consellería de Educación e Ordenación Universitaria of the Xunta de Galicia (grant #GRC2014/039), cofinanced with FEDER funds and the Universidade da Coruña., Xunta de Galicia; GRC2014/039
RUC. Repositorio da Universidade da Coruña
Publicación Contribución de congreso (ConferenceOutput)

Structural topology optimization with high spatial definition by using the overweight approach

  • Villalba Rama, Diego
  • París, José
  • Couceiro, Iván
  • Navarrina, Fermín
High Performance and Optimum Design of Structures and Materials V (WIT Transactions on The Built Environment; v.9). The studies contained in this volume were presented at the International Conference on High Performance and Optimum Structures and Materials Encompassing Shock and Impact Loading and address issues involving advanced types of structures, particularly those based on new concepts, and shock and impact resistance., [Abstract:] The first formulation of topology optimization was proposed in the 1980s. Since then, many contributions have been presented with the purpose of improving its efficiency and expanding its field of application. The aim of this research is to develop a structural topology optimization algorithm considering minimum weight and stress constraints. Structural topology optimization with stress constraints has been previously formulated with several different approaches, mainly: local stress constraints, global stress constraints or block aggregation of stress constraints. In this research the overweight approach, an improvement of the so-called damage approach, is used. In this method, a virtual relative density (VRD) is defined as a function of the violation of the local stress constraints. VRD is increased as the stresses exceed the maximum allowable value, with the exception of the areas with the minimum value of the relative density, since full-void solutions are intended. The distribution of the material in the domain is modelled using two different approaches: a uniform relative density within each element of the mesh and a relative density defined by means of quadratic B-splines. For this reason, the structural analysis is performed by means of the finite element method (FEM) and the isogeometric analysis (IGA) respectively. The optimization is addressed by means of the sequential linear programming algorithm (SLP), which is driven by the information provided by a full first order sensitivity analysis extension of both FEM and IGA formulations. Finally, the overweight approach is tested by means of some two dimensional problems. The domain has been divided in an elevated number of elements to attain high spatial definition solutions. The results show that the overweight approach is a feasible alternative for the damage approach and the stress constraints aggregation techniques to solve the topology optimization problem. A comparison between both formulations of the material distribution is included., This work has received financial support from the Xunta de Galicia (Secretaria Xeral de Universidades) and the European Union (European Social Fund (ESF)) through “Grants for funding predoctoral stages in universities, public research organisms and other R&D entities of Galicia” ED481A-2016/387. This work has also been partially supported also by FEDER funds of the European Union, by the “Ministerio de Economía y Competitividad” of the Spanish Government through grants DPI2015-68431-R and RTI2018-093366-B-I00 and by the “Conselleria de Educación, Universidade e Formación Profesional” of the Xunta de Galicia, through grants for the consolidation and structuring of competitive research units of the Galician University System: GRC2014/039 and GRC2018/41., Xunta de Galicia; ED481A-2016/387, Xunta de Galicia; GRC2014/039, Xunta de Galicia; GRC2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

A new formulation for transient response optimization of structures based on constraint aggregation functions

  • Couceiro, Iván
  • París, José
  • Ramírez, Luis
  • Navarrina, Fermín
Versión aceptada de https://doi.org/10.1080/0305215X.2021.1957469, [Abstract] This article proposes a new formulation for the treatment of time-dependent constraints in the transient response optimization of structures. The novel method is based on constraint aggregation functions. However, instead of lumping the constraints in the physical domain, the method condenses the information of the time-dependent constraints into one equivalent function while retaining information about the point-wise constraints. The formulation is gradient compatible and allows a considerable reduction of the optimization problem. Two versions of the Kreisselmeier–Steinhauser function are studied. The formulation is tested on the size optimization of truss and framed three-dimensional structures subjected to dynamic loads. The methodology is tested in very-large transient response optimization problems in order to check its efficiency. Results show that the formulation is able guarantee the fulfilment of the constraints in the whole time interval studied. The size of the transient response optimization problem is highly reduced, allowing a reduction of the computational resources needed., This work has been partially supported by FEDER funds of the European Union, by the Ministerio de Economía y Competitividad of the Spanish Goverment through grant #DPI2015-68431-R and grant #RTI2018-093366-B-100, by the Secretaría Xeral de Universidades of the Xunta de Galicia through grant #ED431C 2018/41, by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia by a grant awarded to the University of A Coruña, and by research fellowships of the University of A Coruña and the Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; ED431C 2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

An a posteriori-implicit turbulent model with automatic dissipation adjustment for Large Eddy Simulation of compressible flows

  • Nogueira, Xesús
  • Ramírez, Luis
  • Fernández-Fidalgo, Javier
  • Deligant, Michaël
  • Khelladi, Sofiane
  • Chassaing, Jean-Camille
  • Navarrina, Fermín
© 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license https://creativecommons.org/licenses/by-nc-nd/4.0/(opens in new tab/window)  https://www.elsevier.com/about/policies-and-standards/sharing . This is an accepted version of the following published document: https://doi.org/10.1016/j.compfluid.2019.104371, [Abstract] In this work we present an a posteriori high-order finite volume scheme for the computation of compressible turbulent flows. An automatic dissipation adjustment (ADA) method is combined with the a posteriori paradigm, in order to obtain an implicit subgrid scale model and preserve the stability of the numerical method. Thus, the numerical scheme is designed to increase the dissipation in the control volumes where the flow is under-resolved, and to decrease the dissipation in those cells where there is excessive dissipation. This is achieved by adding a multiplicative factor to the dissipative part of the numerical flux. In order to keep the stability of the numerical scheme, the a posteriori approach is used. It allows to increase the dissipation quickly in cells near shocks if required, ensuring the stability of the scheme. Some numerical tests are performed to highlight the accuracy and robustness of the proposed numerical scheme., The authors greatly acknowledge the kind help of Dr. D. P. Rizzeta, Dr. Lin Fu and Dr. H. C. Yee, who kindly share with us the initial conditions for the turbulence decay problems. This work has been partially supported by FEDER funds of the European Union, Grants #DPI2015-68431-R of the Ministerio de Economía y Competitividad and #RTI2018-093366-B-I00 of the Ministerio de Ciencia, Innovación y Universidades of the Spanish Government, by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia (program Axudas para potenciación de grupos de investigación do Sistema Universitario de Galicia 2018, grant #ED431C 2018/41) and Research fellowships of the Universidade da Coruña and the Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; ED431C 2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Smoothed Particle Hydrodynamics: A consistent model for interfacial multiphase fluid flow simulations

  • Krimi, Abdelkader
  • Rezoug, Mehdi
  • Khelladi, Sofiane
  • Nogueira, Xesús
  • Deligant, Michaël
  • Ramírez, Luis
Versión aceptada de https://doi.org/10.1016/j.jcp.2017.12.006, [Abstract:] In this work, a consistent Smoothed Particle Hydrodynamics (SPH) model to deal with interfacial multiphase fluid flows simulation is proposed. A modification to the Continuum Stress Surface formulation (CSS) [1] to enhance the stability near the fluid interface is developed in the framework of the SPH method. A non-conservative first-order consistency operator is used to compute the divergence of stress surface tensor. This formulation benefits of all the advantages of the one proposed by Adami et al. [2] and, in addition, it can be applied to more than two phases fluid flow simulations. Moreover, the generalized wall boundary conditions [3] are modified in order to be well adapted to multiphase fluid flows with different density and viscosity. In order to allow the application of this technique to wall-bounded multiphase flows, a modification of generalized wall boundary conditions is presented here for using the SPH method. In this work we also present a particle redistribution strategy as an extension of the damping technique presented in [3] to smooth the initial transient phase of gravitational multiphase fluid flow simulations. Several computational tests are investigated to show the accuracy, convergence and applicability of the proposed SPH interfacial multiphase model., X. Nogueira and L. Ramirez have been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) of the Spanish Government and by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia (grant #GRC2014/039) cofinanced with FEDER funds, and the Universidade da Coruña., Xunta de Galicia; GRC2014/039
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Dynamic Response Optimization of Steel Jackets for Offshore Wind Turbines With Fatigue and Time-Dependent Constraints

  • Couceiro, Iván
  • París, José
  • Navarrina, Fermín
  • Colominas, Ignasi
  • Casteleiro, Manuel
[Abstract] In this work, a methodology for the shape and sizing optimization of steel jackets for offshore wind turbines considering the full dynamic response of the structure in a fully-coupled model is presented. The coupled model includes the jacket, the transition piece, the tower of the turbine, the rotor-nacelle assembly and the blades. The rotation of the blades is also included in the model. Ultimate limit state (ULS), fatigue limit state (FLS) and natural frequency constraints are imposed to the model and the weight of the steel jacket is optimized using design variables that control the size of the elements and the overall geometry of the structure. A new formulation is introduced to deal with time-dependent ULS constraints allowing an efficient treatment of the constraints while being suitable for gradient-based optimization. The formulation reduces the size of the large-scale constrained optimization problem and the constraints are satisfied at every time-step of the dynamic analysis. This work represents the first optimization approach to tackle the optimization of the jackets in fully-coupled models with constraints in the complete dynamic response and in the fatigue damage. A numerical example is shown and optimized achieving a significant reduction of half of the weight of the structure and a considerable change in the overall geometry of the structure., This work has been partially supported by the Ministerio de Economía y Competitividad (Grants #DPI2015-68431R and #RTI2018-093366-B-I00) of the Spanish Government, by Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia (Grants #GRC2014/039 and #ED431c 2016/41) co-financed with FEDER funds, and by research fellowships of Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431c 2016/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Numerical assessment of fan blades screen effect on fan/OGV interaction tonal noise

  • Foulquié, Charles
  • Khelladi, Sofiane
  • Deligant, Michaël
  • Ramírez, Luis
  • Nogueira, Xesús
  • Mardjono, Jacky
Versión aceptada de https://doi.org/10.1016/j.jsv.2020.115428, [Abstract:] This work deals with sound generation and transmission in a fan stage. The study is done on a subsonic Fan stage and interaction noise between the fan wakes and the Outlet Guide Vanes (OGV) is considered. For this purpose, the Linearized Euler Equations (LEE) are solved with a steady axisymmetric flow. The acoustic sources are modelled by a scattering approach. Numerical simulations are carried out in an unwrapped cylindrical layer using a high-order finite volume solver. In order to explicitly take into account the moving fan blades into the propagation medium, a high-resolution sliding mesh technique is used. The simulation results, which highlight the screen effect of moving fan blades on fan/OGV interaction tones, are consistent with analytical literature., Xesús Nogueira and Luis Ramírez acknowledge the support given by FEDER funds of the European Union, Grants #DPI2015-68431-R of the Ministerio de Economía y Competitividad and #RTI2018-093366-B-I00 of the Ministerio de Ciencia, Innovación y Universidades of the Spanish Government, and by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia (program Axudas para potenciación de grupos de investigación do Sistema Universitario de Galicia 2018, grant #ED431C 2018/41)., Xunta de Galicia; ED431C 2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

A high-order finite volume method with improved isotherms reconstruction for the computation of multiphase flows using the Navier–Stokes–Korteweg equations

  • Martínez, Abel
  • Ramírez, Luis
  • Nogueira, Xesús
  • Khelladi, Sofiane
  • Navarrina, Fermín
Versión aceptada de https://doi.org/10.1016/j.camwa.2019.07.021, [Abstract] In this work we solve the Navier–Stokes–Korteweg (NSK) equations to simulate a two-phase fluid with phase change. We use these equations on a diffuse interface approach, where the properties of the fluid vary continuously across the interface that separates the different phases. The model is able to describe the behavior of both phases with the same set of equations, and it is also able to handle problems with great changes in the topology of the problem. However, high-order derivatives are present in NSK equations, which is a difficulty for the design of a numerical method to solve the problem. Here, we propose the use of a high-order Finite Volume method with Moving Least Squares approximations to handle high-order derivatives and solve the NSK equations. Moreover, a new methodology to obtain accurate equations of state is presented. In this method, we use any accurate equation of state for the pure phases. Under the saturation curve, a B-spline reconstruction fulfilling a given set of thermodynamic criteria is performed. The new EOS can be used for computations using diffuse interface modeling. Several numerical examples to show the accuracy of the new approach are presented., This work has been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) and #RTI2018-093366-B-I00 of the Ministerio de Ciencia, Innovación y Universidades of the Spanish Government and the Universidade da Coruña and by the Consellería de Educación e Ordenación Universitaria of the Xunta de Galicia (grants # GRC2014/039 and # ED431C 2018/41), cofinanced with FEDER funds and the Universidade da Coruña. Xesús Nogueira also acknowledges the funding provided by the Xunta de Galicia through the program Axudas para a mellora, creación, recoñecemento e estruturación de agrupacións estratéxicas do Sistema universitario de Galicia (reference # ED431E 2018/11)., Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431E 2018/11, Xunta de Galicia; ED431C 2018/41
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Optimization of Offshore Steel Jackets: Review and Proposal of a New Formulation for Time-Dependent Constraints

  • Couceiro, Iván
  • París, José
  • Navarrina, Fermín
  • Guizán Roca, Raquel
  • Colominas, Ignasi
Versión aceptada de https://doi.org/10.1007/s11831-019-09342-y, [Abstract:] In this work, a methodology for the optimization of offshore wind turbine substructures (jacket type) is presented. The use of a coupled model allows for capturing the full dynamic interaction between all the elements. The structural analysis is carried out in the time-domain. A non-linear integration scheme is necessarily applied due to the effects of the rotation of the blades. Environmental actions, such as wind and waves, are considered as loading conditions. Fatigue damage at the welds of the joints is taken into account. The objective function to be minimized is the weight of the structure. The shape and sizing optimization model is stated in terms of two variables that define the overall shape of the jacket, along with the dimensions of the cross-sections of the structural members. The model is subjected to Ultimate Limit Stress (ULS), Fatigue Limit State and natural frequency constraints. The time-dependent ULS constraints are efficiently treated by means of a new formulation that is based on constraint aggregation. Fatigue accumulation during the whole design life of the structure is accurately assessed, without the need for excessively costly numerical simulations. The optimization problem is solved by means of Sequential Linear Programming, what requires a full first order sensitivity analysis to be performed. The efficiency, reliability and robustness of the proposed methodology is demonstrated by optimizing a real jacket design., This work has been partially supported by FEDER funds of the European Union, by the Ministerio de Economía y Competitividad of the Spanish Goverment through grant # DPI2015-68431-R, by the Secretaría Xeral de Universidades of the Xunta de Galicia through grant # GRC2014/039 and # ED431C2018/041, by the Consellería de Cultura, Educación e Ordenación Universitaria of the Xunta de Galicia by a grant awarded to the University of A Coruña, and by research fellowships of the University of A Coruña and the Fundación de la Ingeniería Civil de Galicia., Xunta de Galicia; GRC2014/039, Xunta de Galicia; ED431C2018/041
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

An a posteriori, efficient, high-spectral resolution hybrid finite-difference method for compressible flows

  • Fernández-Fidalgo, Javier
  • Nogueira, Xesús
  • Ramírez, Luis
  • Colominas, Ignasi
Versión aceptada de https://doi.org/10.1016/j.cma.2018.02.013, [Abstract:] A high-order hybrid method consisting of a high-accurate explicit finite-difference scheme and a Weighted Essentially Non-Oscillatory (WENO) scheme is proposed in this article. Following this premise, two variants are outlined: a hybrid made up of a Finite Difference scheme and a compact WENO scheme (CRWENO 5), and a hybrid made up of a Finite Difference scheme and a non-compact WENO scheme (WENO 5). The main difference with respect to similar schemes is its a posteriori nature, based on the Multidimensional Optimal Order Detection (MOOD) method. To deal with complex geometries, a multi-block approach using Moving Least Squares (MLS) procedure for communication between meshes is used. The hybrid schemes are validated with several 1D and 2D test cases to illustrate their accuracy and shock-capturing properties., This work has been partially supported by the Ministerio de Economía y Competitividad (grant #DPI2015-68431-R) of the Spanish Government and by the Consellería de Educación e Ordenación Universitaria of the Xunta de Galicia (grant #GRC2014/039), cofinanced with FEDER funds and the Universidade da Coruña., Xunta de Galicia; GRC2014/039