Pasar al contenido principal

SISTEMA GENERADOR DE POTENCIA DE ALTA DENSIDAD ENERGETICA ALIMENTADO CON (BIO)ETANOL PARA APLICACION EN ELECTRONICA DE CONSUMO Y MICROSISTEMAS

ENE2010-14833

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario FUNDACIO INSTITUT DE RECERCA DE L ENERGIA DE CATALUNYA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Full ceramic micro solid oxide fuel cells: Towards more reliable MEMS power generators operating at high temperatures

  • Garbayo, Iñigo
  • Pla, Dolors
  • Morata, Alex
  • Fonseca, Luis
  • Sabaté Vizcarra, Neus
  • Tarancón, Albert
Batteries, with a limited capacity, have dominated the power supply of portable devices for decades. Recently, the emergence of new types of highly efficient miniaturized power generators like micro fuel cells has opened up alternatives for continuous operation on the basis of unlimited fuel feeding. This work addresses for the first time the development of a full ceramic micro solid oxide fuel cell fabricated in silicon technology. This full-ceramic device represents a new generation of miniaturized power generators able to operate at high temperatures, and therefore able to work with a hydrocarbon fuel supply. Dense yttria-stabilized zirconia free-standing large-area membranes on micromachined silicon were used as the electrolyte. Thin-film porous electrodes of La0.6Sr0.4CoO3-δ and gadolinia-doped ceria were employed as cathode and anode materials, respectively. The electrochemical performance of all the components was evaluated by partial characterization using symmetrical cells, yielding excellent performance for the electrolyte (area specific resistance of 0.15 Ω cm2 at temperatures as low as 450 °C) and the electrodes (area specific resistance of the cathode and anode below 0.3 Ω cm2 at 700 °C). A micro solid oxide fuel cell with an active area of 2 mm2 and less than 1 micrometer in thickness was characterized under fuel cell conditions, using hydrogen as a fuel and air as an oxidant. A maximum power density of 100 mW cm-2 and 2 mW per single membrane was generated at 750 °C, having an open circuit voltage of 1.05 V. Impedance spectroscopy of the all-ceramic membrane showed a total area-specific resistance of ∼3.5 Ω cm2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Is it possible to design a portable power generator based on micro-solid oxide fuel cells? A finite volume analysis

  • Pla, D.
  • Sánchez-González, A.
  • Garbayo, Iñigo
  • Salleras, Marc
  • Morata, Alex
  • Tarancón, Albert
Abstract The inherent limited capacity of current battery technology is not sufficient for covering the increasing power requirements of widely extended portable devices. Among other promising alternatives, recent advances in the field of micro-Solid Oxide Fuel Cells (μ-SOFCs) converted this disruptive technology into a serious candidate to power next generations of portable devices. However, the implementation of single cells in real devices, i.e. μ-SOFC stacks coupled to the required balance-of-plant elements like fuel reformers or post combustors, still remains unexplored. This work aims addressing this system-level research by proposing a new compact design of a vertically stacked device fuelled with ethanol. The feasibility and design optimization for achieving a thermally self-sustained regime and a rapid and low-power consuming start-up is studied by finite volume analysis. An optimal thermal insulation strategy is defined to maintain the steady-state operation temperature of the μ-SOFC at 973 K and an external temperature lower than 323 K. A hybrid start-up procedure, based on heaters embedded in the μ-SOFCs and heat released by chemical reactions in the post-combustion unit, is analyzed allowing start-up times below 1 min and energy consumption under 500 J. These results clearly demonstrate the feasibility of high temperature μ-SOFC power systems fuelled with hydrocarbons for portable applications, therefore, anticipating a new family of mobile and uninterrupted power generators., The research is supported by Ministerio de Economía y Competitividad – Plan Nacional de I+D+i, projects ENE2010-14833 (POWER PACK) and ENE2012-36368. The authors acknowledge the Ramon y Cajal (AT and NS) and Juan de la Cierva (AM) programs., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Standalone ethanol micro-reformer integrated on silicon technology for onboard production of hydrogen-rich gas

  • Pla, D
  • Salleras, Marc
  • Morata, A
  • Garbayo, Iñigo
  • Gerbolés, Marta
  • Sabaté Vizcarra, Neus
  • Divins, N J
  • Casanovas, A
  • Llorca, J
  • Tarancón, Albert
A novel design of a silicon-based micro-reformer for onboard hydrogen generation from ethanol is presented in this work. The micro-reactor is fully fabricated with mainstream MEMS technology and consists of an active low-thermal-mass structure suspended by an insulating membrane. The suspended structure includes an embedded resistive metal heater and an array of ca. 20k vertically aligned through-silicon micro-channels per square centimetre. Each micro-channel is 500 μm in length and 50 μm in diameter allowing a unique micro-reformer configuration that presents a total surface per projected area of 16 cm(2) cm(-2) and per volume of 320 cm(2) cm(-3). The walls of the micro-channels become the active surface of the micro-reformer when coated with a homogenous thin film of Rh-Pd/CeO2 catalyst. The steam reforming of ethanol under controlled temperature conditions (using the embedded heater) and using the micro-reformer as a standalone device are evaluated. Fuel conversion rates above 94% and hydrogen selectivity values of ca. 70% were obtained when using operation conditions suitable for application in micro-solid oxide fuel cells (micro-SOFCs), i.e. 750 °C and fuel flows of 0.02 mlL min(-1) (enough to feed a one watt power source)., The research was supported by Ministerio de Economía y Competitividad – Plan Nacional de I+D+i, projects POWER PACK (ENE2010-14833), ENE2012-36368, ENE2015-63969-R and BELIF (TEC2015-62519-ERC). The authors acknowledge the Ramon y Cajal (AT and NS) and Juan de la Cierva (AM) programs. NJD acknowledges UPC for a PhD grant. JL is Serra Hunter Fellow and is grateful to ICREA Academia program., Peer reviewed