Pasar al contenido principal

DESARROLLO DE LA COMBUSTION DE CARBON CON CAPTURA DE CO2 POR EL PROCESO CHEMICAL LOOPING CON GENERACION DE OXIGENO

ENE2016-77982-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 28
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Life cycle assessment of natural gas fuelled power plants based on chemical looping combustion technology

  • Navajas León, Alberto
  • Mendiara, Teresa
  • Goñi, Víctor
  • Jiménez, Adrián
  • Gandía Pascual, Luis
  • Abad, Alberto
  • García Labiano, Francisco
  • Diego, Luis F. de
Among the different Carbon Capture and Storage (CCS) technologies being developed in the last decades, Chemical Looping Combustion (CLC) stands out since it allows inherent CO2 capture. In the CLC process, there is a solid oxygen carrier circulating between two reactors in a cycle that allows providing the oxygen needed for combustion. In one of the reactors, named as fuel reactor, the fuel is introduced and combusted while the oxygen carrier reduction takes place. In the second reactor, named air reactor, the oxygen carrier is reoxidized in air. Different materials based on copper, nickel and iron oxides have been proposed as oxygen carriers for the CLC process. This work presents an environmental evaluation of the CLC process for natural gas based on Life Cycle Assessment (LCA). Five different oxygen carrier materials already tested in pilot plants were considered and the results compared to the conventional natural gas combustion in a gas turbine in a combined cycle without and with CO2 capture using postcombustion capture with amines. In view of the results, lower impact of the CLC process compared to the base case is expected without and with CO2 capture. The influence of several variables on the results was considered, such as temperature in the air reactor, lifetime of the oxygen carrier and possibility of recuperation of the depleted oxygen carrier. The nickel-based oxygen carriers were identified as the most adequate to be used in natural gas combustion. However, due to their toxicity, several analyses were also performed in order to identify improvements in the known oxygen carriers that can qualify them to replace nickel-based materials., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) [grant numbers ENE2017-89473-R, ENE2016-77982-R] and the European Regional Development Fund (ERDF) under the program 'Programa Operativo FEDER Aragón 2014-2020 - Construyendo Europa desde Aragón. Proyecto BiosinCO2 (LMP180_18)'.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Coal combustion with a spray granulated Cu-Mn mixed oxide for the Chemical Looping Oxygen Uncoupling (CLOU) process

  • Adánez-Rubio, Iñaki
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The Chemical Looping with Oxygen Uncoupling (CLOU) process is a form of Chemical Looping Combustion (CLC) technology that enables the combustion of solid fuels by means of oxygen carriers that release gaseous oxygen in the fuel reactor, i.e. with oxygen uncoupling capability. In recent years, tests have found several Cu-based, Mn-based and mixed oxide oxygen carriers with suitable properties for the CLOU process. Among them, Cu-Mn mixed oxides show high reactivity and high O2 equilibrium concentration at temperatures of interest for coal combustion. In this work, proof of concept was demonstrated by burning coal with Cu-Mn mixed oxides in a 1.5 kWth CLOU unit for the first time. The effect of fuel reactor temperature, solids circulation flow, fluidization agent in the fuel reactor (inert N2 or steam as gasifying agent), and excess air in the air reactor on combustion efficiency and CO2 capture rate was analysed. The results showed that high combustion efficiency and CO2 capture are feasible using this material at relatively low fuel reactor operating temperatures. Therefore, the developed Cu-Mn mixed oxide was a suitable material for use as an oxygen carrier for the CLOU combustion of solid fuels. Optimum operating conditions were determined for this oxygen carrier with regard to the oxygen circulation rate and air reactor conditions for the regeneration of the oxygen carrier., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Project: ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds. Our thanks to Ing. Konrad Holscher from Mina Invierno Chile, for supplying the subbituminous coal., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of (Mn0.77Fe0.23)2O3 particles as an oxygen carrier for coal combustion with CO2 capture via in-situ gasification Chemical Looping Combustion (iG-CLC) aided by Oxygen Uncoupling (CLOU)

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical looping combustion (CLC) involves the use of a solid oxygen carrier to transport the oxygen from the air to a fuel. Attention has recently been focused on oxygen carriers based on Mn-Fe mixed oxides because they are cheap materials that are able to release oxygen at high temperature, the so-called oxygen uncoupling step. The aim of this work was to assess the use of (Mn0.77Fe0.23)2O3 material as an oxygen carrier with the ability to transport oxygen both by reduction with gaseous fuels and by oxygen uncoupling, i.e. typical mechanisms in CLC and in Chemical Looping with Oxygen Uncoupling (CLOU), respectively. The particles prepared by mechanical mixing were screened to obtain particles of sufficient reactivity and mechanical strength for use in a fluidized bed reactor. The preparation methodology and calcining temperature were varied. The reactivity of one selected material was evaluated by performing redox cycles both in a TGA and a batch fluidized-bed reactor. Thus, its behaviour was assessed during both decomposition-regeneration of bixbyite phase [(Mn0.77Fe0.23)2O3] in CLOU and the reduction-oxidation of spinel phase [(Mn0.77Fe0.23)3O4] with gaseous fuels, i.e. H2, CO and CH4. Its oxygen uncoupling and re-oxidation capability was highly influenced by the reaction temperature and oxygen concentration. On the other hand, CLC redox cycles with gaseous fuels showed high reactivity with H2 and CO and high oxygen transport capacity by reduction to mangano-wüstite phase [(Mn0.77Fe0.23)O]. Good fluid-dynamic behaviour was observed for the oxygen carrier particles along the redox cycles without agglomeration problems, regardless of the operating conditions used in the batch fluidized-bed reactor. Thus, the selected material was considered a promising candidate for use in both in CLC with syngas and CLC with coal., This work was partially supported by the Spanish Ministry for Economy and Competitiveness via the ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R projects, by the European Regional Development Fund (ERDF), and by the Spanish National Research Council (CSIC) via the 2014-80E101 project. R. Pérez-Vega is grateful to MICINN for the FPI Fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spray granulated Cu-Mn oxygen carrier for Chemical Looping with Oxygen Uncoupling (CLOU) process

  • Adánez-Rubio, Iñaki
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, One form of Chemical Looping Combustion (CLC) with CO2 capture as an alternative to the burning of solid fuels is the Chemical Looping with Oxygen Uncoupling (CLOU) process. The CLOU process requires metal oxides with O2 release capacity at temperatures that are suitable for solid fuel combustion, e.g. copper and manganese oxides. A Cu-Mn mixed oxide comprising 34 wt% CuO and 66 wt% Mn3O4 and prepared by fluidized bed granulation was analysed for use as an oxygen carrier for the CLOU process. TGA and batch fluidized bed reactors were used to investigate oxygen generation rates, agglomeration behaviour and oxygen carrier attrition. A medium volatile coal from South Africa and its char were used as fuel in a batch fluidized bed reactor in a temperature range of 800–930 °C. The Cu-Mn oxygen carrier showed good release O2 rate and a high rate of oxygen transfer by direct gas-solid reaction. The presence of CO as a combustion product appeared only at low oxygen carrier to coal ratios. This material has the capacity to generate O2 at lower temperatures than needed for Cu-based oxygen carriers, which suggests that this material is suitable for work at lower temperatures in a fuel reactor with complete combustion of the fuel. The low attrition rate and attrition index, together with the stable crushing strength of the particles with redox cycles, make this Cu-Mn oxygen carrier suitable for operation in a continuous CLOU unit., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness via the Projects ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical Looping Combustion of gaseous and solid fuels with manganese-iron mixed oxide as oxygen carrier

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
© 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Synthetic manganese-iron mixed oxides are considered promising materials to be used as oxygen carriers for Chemical Looping Combustion of coal with carbon dioxide capture at low cost. The aim of this work was to evaluate a manganese-iron mixed oxide material with a manganese to iron molar ratio of 0.77:0.23 as oxygen carrier for coal combustion by means of chemical looping processes, including both ex-situ and in-situ gasification of coal. The preparation method -spray drying followed by calcination- was optimized in order to produce particles with high reactivity and mechanical strength. The material was studied in two continuously operated facilities designed to burn either gaseous or solid fuels. While full combustion was achieved burning syngas, showing the feasibility of the use of this material considering the ex-situ gasification process. Coal combustion efficiency by in-situ gasification process was improved in comparison with other previously tested low-cost materials such as ilmenite and iron ore. Moreover, the oxygen carrier particles showed an interesting magnetic behavior that was able to facilitate oxygen carrier recovery from the purge ash stream. In view of these results, the manganese-iron mixed oxide as oxygen carrier is proposed as a promising candidate for use coal combustion by the chemical looping process., This work was partially supported by the Spanish Ministry for Economy, Industry and Competitiveness (MINECO Projects: ENE2014-56857-R and ENE2016-77982-R projects), by the European Regional Development Fund (ERDF) and by the Spanish National Research Council (CSIC) via the 2015-80E100 and 2017-80E035 projects. The authors also thank Ing. Konrad Holscher from “Mina Invierno” (Chile) for providing the subbituminous coal used in this work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of the improvement of chemical looping combustion of coal by using a manganese ore as oxygen carrier

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Mendiara, Teresa
  • Bueno, José A.
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Finding suitable low-cost materials to be used as oxygen carrier in Chemical Looping Combustion (CLC) of coal is a key issue to achieve the CO2 capture at low economic cost. Recently, a Mn-ore from Gabon has been identified as an alternative to the state of the art of oxygen carriers based on minerals or wastes with high iron content. This Mn-ore showed a high reactivity and a long particle lifetime during batch characterization to be considered as a suitable oxygen carrier. To evaluate the potential of this material in CLC, this work analyses the behaviour of the Mn-ore during continuous combustion of a bituminous coal in a 0.5 kWth CLC unit. The CLC process was evaluated and the effect of the main operating variables - such as fluidizing medium, oxygen carrier circulation rate, temperature, and solids inventory in the fuel reactor - on the combustion efficiency and CO2 capture was investigated. A direct relation between the char conversion rate and the CO2 capture is given, being mainly affected by the mean residence time of solids and temperature in the fuel reactor. The use of a carbon separation system with separation efficiency above 90% would be required to achieve CO2 capture rates higher than 95%. Total oxygen demand values as low as 4.5% were found when optimal operating conditions were selected, mainly being related to oxygen carrier to fuel ration higher than ϕ > 3. At these conditions, the Mn-ore material showed similar combustion efficiencies than other Fe-based low-cost materials previously tested, but with higher CO2 capture rates., This work was partially supported by the Ministry of Economy, Industry and Competitiveness via ENE2014-56857-R, ENE2016-77982-R and CSIC-2017-80E035 projects, and the European Regional Development Fund (ERDF). J.A. Bueno thanks for the FPI Fellowship. T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post-doctoral contract., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improving the efficiency of Chemical Looping Combustion with coal by using ring-type internals in the fuel reactor

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • Bueno, José A.
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
7 Figures, 5 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) with solid fuels has been widely developed by using two interconnected fluidized beds, the fuel reactor and the air reactor, with an oxygen carrier continuously circulating between them. Experience gained in this process shows that high CO2 capture values can be reached. However, complete combustion of the fuel is not achieved, with some H2, CO and CH4 as the main unconverted compounds in the combustion products from the fuel reactor. It is believed that the combustion efficiency can be increased by improving the gas-solid contact in the fuel reactor. In this work, the solids distribution in the fuel reactor was modified by using ring-type internals with the objective of enhancing the gas-solid contact. Two experimental campaigns were carried out in a 50 kWth CLC unit burning a bituminous coal with ilmenite particles in the temperature interval of 900–1000 °C. The first campaign was conducted with the original riser of the fuel reactor, which was characterized by a smooth section from bottom to top. For the second campaign, three ring-type internals were implemented in the riser in order to modify the solids distribution in the fuel reactor. The presence of the internals had a beneficial effect on the coal combustion. The major benefit was an improved oxidation of volatile matter in the form of CH4 and the full conversion of H2. As a result, the total oxygen demand decreased by 20%, from 12.2% to 9.8%, with the implementation of the internals., This work was supported by the Ministerio de Economía, Industria y Competitividad (projects ENE2014-56857-R and ENE2016-77982-R), the Spanish National Research Council (CSIC project: 2017-80E035), the Research Fund for Coal and Steel (RFCS project ACCLAIM: RFCP-CT-2012-00006) and the European Regional Development Fund (ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modelling Chemical-Looping assisted by Oxygen Uncoupling (CLaOU): Assessment of natural gas combustion with calcium manganite as oxygen carrier

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
7 Figures, 2 Tables.-- Supplementary material available.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical-Looping Combustion (CLC) is a promising technology for performing CO2 capture in combustion processes at low cost and with lower energy consumption. Fuel conversion modelling assists in optimizing and predicting the performance of the CLC process under different operating conditions. For this work, the combustion of natural gas was modelled using a CaMnO3-type perovskite as oxygen-carrier and taking into consideration the processes of fluid dynamics and reaction kinetics involved in fuel conversion. The CLC model was validated against experimental results obtained from the 120 kWth CLC unit at the Vienna University of Technology (TUV). Good agreement between experimental and model predictions of fuel conversion was found when the temperature, pressure drop, solids circulation rate and fuel flow were varied. Model predictions showed that oxygen transfer by means of the gas–solid reaction of the fuel with the oxygen-carrier was relevant throughout the entire fuel-reactor. However, complete combustion could be only achieved under operating conditions where the process of Chemical-Looping assisted by Oxygen Uncoupling (CLaOU) became dominant, i.e. a relevant fraction of the fuel was burnt with molecular oxygen (O2) released by the oxygen-carrier. This phenomenon was improved by the design configuration of the 120 kWth CLC unit at TUV, in which oxidized particles are recirculated to the upper part of the fuel-reactor. Thus, the validated model identified the conditions at which complete combustion can be achieved, demonstrating that it is a powerful tool for the simulation and optimization of the CLC process with the CaMnO3-type material., This work was supported by the seventh Framework Programme of the European Commission (INNOCUOUS Contract 241401), by the Spanish Ministry of Economy, Industry and Competitiveness (project ENE2016-77982-R), by the European Regional Development Fund (ERDF) and by the CSIC (project 2017-80E035). Authors thanks to K. Mayer and S. Penthor (TUV) for providing experimental data., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of Mn-Fe mixed oxide doped with TiO2 for the combustion with CO2 capture by Chemical Looping assisted by Oxygen Uncoupling

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
11 Figures, 2 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Bimetallic manganese-iron materials have been identified as suitable oxygen carriers for Chemical Looping Combustion (CLC) and Chemical Looping with Oxygen Uncoupling (CLOU) processes. These materials allow the combustion of a fuel with inherent CO2 capture according to two parallel mechanisms: reaction with lattice oxygen and oxygen uncoupling. This work is focused on the evaluation of the reactivity and physicochemical characterization of oxygen carrier particles consisting of a manganese-iron mixed oxide with manganese to iron molar ratio of 66:34 and doped with titanium (7 wt% TiO2) with the objective of determining suitable conditions to be used in CLC and CLOU processes. Particles were prepared by spray drying and the sintering procedure was optimized in order to achieve particles with high reactivity and mechanical strength. In addition, suitable magnetic properties were also sought in order to allow oxygen carrier recover and reuse in a chemical looping unit burning solid fuels. Optimum operating conditions for the fuel combustion and regeneration stages were determined in order to promote the oxygen uncoupling mechanism. Thus, temperature during the fuel combustion must be as high as possible to enhance the oxygen transference; but conditions for oxygen carrier regeneration by air must be carefully selected in order to take advantage of the oxygen uncoupling capability of this material. An oxidizing temperature interval of 1123–1173 K maximized the regeneration, while an air excess higher than 20% would be recommended in order to guarantee oxygen uncoupling capability., This work was partially supported by the Spanish Ministry for Economy, Industry and Competitiveness (MINECO Projects: ENE2014-56857-R and ENE2016-77982-R projects), by the European Regional Development Fund (ERDF), and by the Spanish National Research Council (CSIC) via the 2017-80E035 project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A simple model for comparative evaluation of different oxygen carriers and solid fuels in iG-CLC processes

  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
5 Tables, 8 Figures.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, A simple model based on oxygen carrier kinetics has been developed for the in situ Gasification Chemical Looping Combustion (iG-CLC) process. Once the kinetic parameters for different oxygen carriers and solid fuels are known, the model allows easy and fast comparison of different oxygen carrier-solid fuel pairs, which is the main purpose of the model here presented. The comparison is based on the estimation of the CO2 capture efficiency value (ηCC) and the total oxygen demand (ΩT) as evaluating parameters. To show the proposed procedure for the comparison, two Fe-based oxygen carriers (ilmenite and Tierga ore), and five different types of solid fuels: anthracite (Yangquan), sub-bituminous (Tremedal), two bituminous coals (Cerrejón and Taldinsky) and one biomass (olive tree pruning) have been considered. The comparison of the calculated CO2 capture efficiency and total oxygen demand must be done including the effect of operating conditions such as temperature and solids circulation rate. A set of optimized operating conditions are given as a reference for future evaluations of different oxygen carrier-solid fuel pairs. This method is thought as a useful tool for a preliminary evaluation of new oxygen carriers for iG-CLC with different solid fuels., This work was supported by the Spanish Ministry of Economy and Competitiveness (projects ENE2014-56857-R, ENE2016-77982-R), by the European Regional Development Fund (ERDF), the EU project ACCLAIM (RFCP-CT-2012-00006). T. Mendiara thanks for the “Ramón y Cajal” post-doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness. The authors also thank PROMINDSA for providing the iron ore used in this work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Negative CO2 emissions through the use of biofuels in chemical looping technology: A review

  • Mendiara, Teresa
  • García Labiano, Francisco
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
15 Figures, 11 Tables.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In order to limit the increase in the global average temperature to 2 °C or below, the Paris Agreement proposed the reduction of CO2 emissions throughout this century. Bioenergy with CO2 capture and storage (BECCS) technologies represent an interesting option in order to allow this goal to be metgoal, because they are able to achieve negative CO2 emissions. Chemical looping (CL) is recognized as one of the most innovative CO2 capture technologies owing to its low energy penalty. CL processes permit the utilization of renewable fuels in a nitrogen-free atmosphere, given that the required oxygen is supplied by solid oxygen carriers. The present work presents an overview of the status of development of the use of biofuels in chemical looping technologies, including chemical looping combustion (CLC) and chemical looping with oxygen uncoupling (CLOU) for the production of heat/electricity, as well as chemical looping reforming (CLR), chemical looping gasification (CLG) and chemical looping coupled with water splitting (CLWS) for syngas/H2 generation. The main milestones in the development of such processes are shown, and the future trends and opportunities for CL technology with biofuels are discussed., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (projects ENE2014-56857-R, ENE2016-77982-R, and ENE2017-89473-R), the European Regional Development Fund (ERDF), the Spanish National Research Council -CSIC- (201780E035) and the Regional Government of Aragón (T05_17R). T. Mendiara is grateful for the “Ramón y Cajal” post-doctoral contract awarded by MINEICO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reduction and oxidation kinetics of Tierga iron ore for Chemical Looping Combustion with diverse fuels

  • Mendiara, Teresa
  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
11 Figures, 4 Tables.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The in-situ Gasification Chemical Looping Combustion (iG-CLC) process allows combustion with inherent CO2 capture. In this process, the oxygen for combustion is commonly supplied by a solid oxygen carrier based on a metal oxide thus avoiding direct contact between fuel and air. The oxygen carrier circulates between two reactors. In the fuel reactor, the fuel is oxidized to CO2 and H2O while the oxygen carrier is reduced. In the air reactor, the reduced oxygen carrier is regenerated in air. Ilmenite has been widely used as a low-cost oxygen carrier for the iG-CLC process, and it can be taken as a reference material. Recently, the Tierga iron ore has been identified as a promising candidate for further scale-up of the process due to the higher combustion efficiency achieved compared to the results using ilmenite. Modelling of the iG-CLC process with Tierga iron ore as oxygen carrier is a key step to determine the potential of this material. In order to model the iG-CLC process it is necessary to know the reactivity of both oxygen carrier and fuel used. In this paper, the kinetic determination for the reduction and oxidation reactions of the Tierga ore is presented. Reaction orders close to unity were obtained for the main reducing gases, i.e. H2, CO and CH4, as well as O2. The activation energy values obtained were 81.1 ± 7, 76.1 ± 6 and 257 ± 14 kJ/mol for H2, CO and CH4, respectively. The activation energy for oxidation was determined as 18.4 ± 0.5 kJ/mol. In addition, a simple method is used for a comparison of the performance of different oxygen carriers based on their kinetics., This work was supported by the Spanish Ministry of Economy and Competitiveness (projects ENE2014-56857-R, ENE2016-77982-R), by the European Regional Development Fund (ERDF), the EU project ACCLAIM (RFCP-CT-2012-00006). T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post-doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness. The authors also thank PROMINDSA for providing the iron ore used in this work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mn-based oxygen carriers prepared by impregnation for Chemical Looping Combustion with diverse fuels

  • Costa, T. R.
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Melo, Dulce M. A.
  • Adánez Elorza, Juan
13 Figures, 4 Tables.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) is considered one of the low cost alternatives for CO2 capture for fossil fuels combustion and to reach negative emissions through biomass CLC. The cornerstone of the CLC process is the oxygen carrier performance that represents the main additional cost with respect to the conventional combustion. Manganese-based oxygen carriers are subjected to a growing interest because they are low cost, not toxic and environmentally friendly. In this work five impregnated oxygen carriers, with manganese oxide Mn3O4 or Mg6MnO8 as their active phase and three commercial supports based on zirconia and synthetic calcium aluminate, were prepared. Their behaviour for CLC was examined by TGA, batch fluidized bed reactor, TPR, SEM-EDX and XRD. After a preliminary screening two carriers (Mn-ZrM and Mn-ZrSG) were subjected to multiple redox cycles by TGA and batch fluidized bed reactor. Both showed high solids conversion by TGA under the tested conditions, appropriated resistance to fracture, rate indexes relatively high, although Mn-ZrM showed agglomeration and deactivation during batch fluidized bed tests. Reactivity in batch fluidized bed reactor of the Mn-ZrSG oxygen carrier with methane increases with temperature although suffered from significant deactivation. This was different to the results found during multiple redox cycles by TGA. There was not a clear reason for this decrease in the reactivity that likely could be due to the uncomplete oxidation in the batch fluidized bed reactor, although further investigations are needed. On the other hand, it presented high and constant reactivity with CO and H2 in all the range of temperatures tested, being suitable for iG-CLC processes of coal or biomass and syngas combustion. Agglomeration problems were not found and the attrition losses were small. Calculated lifetime was around 11,000 h, much higher than any other Mn-based material developed or tested for CLC., This work was partially supported by the Spanish Ministry of Economy and Competitiveness via ENE2014‐56857‐R and ENE2016‐77982‐R, by the European Regional Development Fund (ERDF). The authors thanks to CNPq for the funding received by the Project 405792/2013‐1 and T. Costa thanks to CNPq for the grant SWE 200354/2014‐0., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical looping combustion of solid fuels

  • Adánez Elorza, Juan
  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
47 Figuras,11 Tablas.-- Título del postprint: Review and assessment of experimental results from Chemical Looping Combustion units burning solid fuels.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) has arisen during last years as a very promising combustion technology for power plants and industrial applications, with inherent CO2 capture which reduces the energy penalty imposed on other competing technologies. The use of solid fuels in CLC has been highly developed in the last decade and currently stands at a technical readiness level (TRL) of 6. In this paper, experience gained during CLC operation in continuous units is reviewed and appraised, focusing mainly on technical and environmental issues relating to the use of solid fuels. Up to now, more than 2700 h of operational experience has been reported in 19 pilot plants ranging from 0.5 kWth to 4 MWth. When designing a CLC unit of solid fuels, the preferred configuration for the scale-up is a two circulating fluidized beds (CFB) system. Coal has been the most commonly used solid fuel in CLC, but biomass has recently emerged as a very promising option to achieve negative emissions using bioenergy with carbon dioxide capture and storage (BECCS). Mostly low cost iron and manganese materials have been used as oxygen carriers in the so called in-situ gasification CLC (iG-CLC). The development of Chemical Looping with Oxygen Uncoupling (CLOU) makes a qualitative step forward in the solid fuel combustion, due to the use of materials able to release oxygen. The performance and environmental issues of CLC of solid fuels is evaluated here. Regarding environmental aspects, the pollutant emissions (SO2, NOx, etc.) released into the atmosphere from the air reactor are no cause of concern for the environment. However, the presence of SO2, NOx and Hg at the exit of the fuel reactor affects CO2 quality, which must be taken into account during the later compression and purification stages. The effect of the main variables affecting CLC performance is evaluated for fuel conversion, CO2 capture rate, and combustion efficiency obtained in different CLC units. Solid fuel conversion is normally not complete during operation, due to the undesired loss of char. A methodology is presented to extrapolate the current information to what could be expected in a larger CLC system. CO2 capture near 100% has been reported using a highly efficient carbon stripper, highly reactive fuels (such as lignites and biomass, etc.) or by the CLOU process. Operational experience in iG-CLC has showed that it is not possible to reach complete fuel combustion, making an additional oxygen polishing step necessary. For the further scale-up, it is essential to reduce the unburnt compounds at the fuel reactor outlet. Proposals to achieve this reduction already exist and include both improvement to the gas-oxygen carrier contact, or new design concepts based on the current scheme for iG-CLC. In addition, CLOU based on copper materials has shown that complete fuel combustion could be achieved. Main challenges for the future development and scale-up of CLC technology have been also identified. A breakthrough in the future development of CLC technology for solid fuels will come from developing long-life materials for CLOU that are easy to recover from the ash purge stream., This work was supported by the Spanish Ministry of Economy and Competitiveness (projects ENE 2013-45454-R, ENE2014-56857-R and ENE2016-77982-R), by the European Regional Development Fund (ERDF), by the CSIC (projects 2014-80E101 and 201780E035) and by the Government of Aragón (Spain, Ref. T06). T. Mendiara gives thanks for the Ramón y Cajal post-doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Relevance of plant design on CLC process performance using a Cu-based oxygen carrier

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
13 Figures, 4 Tables.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Previously validated mathematical CLC models were used to simulate the process performance of CLC methane combustion using an impregnated Cu-based material and to analyse the effect of the fuel reactor design; being either a bubbling fluidized bed or a circulating fluidized bed. The CLC models considered both the fluid dynamic of the fluidized beds at the specific regime and the corresponding kinetics of oxygen carrier reduction. From the model outputs, the performance of the different systems was assessed by calculating the methane conversion in the fuel reactor. Main results highlights that the selection of a suitable particle size of the oxygen carrier and cross section area are key factors to achieve complete combustion with low solids inventory in the fuel reactor. In addition, the growing of bubbles should be limited in order to achieve high CH4 conversion with low solids inventory values, mainly in the bubbling regime with low cross section areas. Complete combustion was predicted with solids inventory in the fuel reactor of 250 kg/MWth (1 m2/MW and particle size of 0.25 mm) or 125 kg/MWth (0.2 m2/MW and a particle size of 0.15 mm) in the bubbling and turbulent regime, respectively. Considering the pressure drop related to these conditions, conclusions for the optimization design of a CLC unit using the Cu-based oxygen carrier are drawn based on the results of the modelling and simulation., This paper was supported by the European Commission Seventh Framework Program under the grant agreement N° 608571 (Project acronym SUCCESS), and by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Projects: ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CLOU process performance with a Cu-Mn oxygen carrier in the combustion of different types of coal with CO2 capture

  • Adánez-Rubio, Iñaki
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
5 Figures, 3 Tables.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The Chemical Looping with Oxygen Uncoupling (CLOU) process is a Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with inherent CO2 separation by using oxygen carriers based on metal oxides. This technology has a low energy penalty and thus low CO2 capture costs. The oxygen carrier used in the CLOU process must be able to release gaseous oxygen, an aspect that limits the availability of metal oxides for this process. This work investigated the suitability of an oxygen carrier containing 34 wt% CuO and 66 wt% Mn3O4 (active phase Cu1.5Mn1.5O4) prepared by granulation regarding the CO2 capture, combustion efficiency and lifetime of the particles. The effect of the different types of coal (two sub-bituminous and a lignite) on combustion and CO2 capture efficiencies by CLOU was studied at different oxygen carrier to coal ratios in a continuous 1.5 kWth rig. It was found that full combustion could be reached regardless of the coal used. However, CO2 capture efficiencies were highly determined by coal rank. Finally, it was found that working with oxygen carrier to coal ratios higher than ϕ = 4, which corresponded to values of the variation of the oxygen carrier conversion lower than ΔXoc = 0.25, decreased the effect of chemical stress on the attrition rate. Therefore, it is clearly beneficial for the lifetime of oxygen carrier particles to operate with low variations of the oxygen carrier conversion (ΔXoc) between fuel and air reactors., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Projects: ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Comparative study of fuel-N and tar evolution in chemical looping combustion of biomass under both iG-CLC and CLOU modes

  • Pérez-Astray, Antón
  • Adánez-Rubio, Iñaki
  • Mendiara, Teresa
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
8 Figures, 6 Tables.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical looping combustion (CLC) processes combined with CO2 sequestration and sustainable management of biomass represent a promising BioEnergy with Carbon Capture and Storage (BECCS) technology. One of the aspects to be considered in the combustion of biomass is the formation of NOx and the possible existence of tar in the gaseous product stream. The advantage of the CLC technology compared to other CO2 capture technologies is that only fuel-N contributes to nitrogen oxides formation. Moreover, scarce information is available about tar formation in CLC. Thus, this work focuses on these two aspects and compares the results obtained when two different chemical looping combustion modes are used, namely In Situ Gasification Chemical Looping Combustion (iG-CLC) and Chemical Looping with Oxygen Uncoupling (CLOU). Important differences were observed depending on the combustion mode. In both cases most of the fuel-N appeared as N2 in the fuel reactor. However, in iG-CLC more than 94% of the nitrogen measured in the fuel reactor was N2 independently of the biomass used. These percentages under the CLOU mode were lower. In this case, low amounts of N2O were also detected, although it decreased to almost zero at 850 °C. In the air reactor, NO was found and its concentration remained below the legal limit for NOx emissions in power installations with all the types of biomass tested and operating modes. Tar species and concentrations found at the fuel reactor outlet stream were different under the two combustion modes. About 2.5–3.7 g/Nm3 total tar could be found at 980 °C burning under iG-CLC mode, mostly naphthalene. On the contrary, insignificant tar amounts were found in CLOU., The authors thank the Spanish Ministry of Economy and Competitiveness (MINECO) for the funding received from the projects ENE2014-56857-R and ENE2016-77982-R as well as FEDER for the financial support. A. Pérez-Astray thanks MINECO for the BES-2015-074651 pre-doctoral fellowship co-financed by the European Social Fund. I. Adánez-Rubio acknowledges MINECO and Universidad de Zaragoza (UNIZAR) for the post-doctoral grant awarded (FJCI-2015-23862). T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post-doctoral contract awarded by MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermochemical assessment of chemical looping assisted by oxygen uncoupling with a MnFe-based oxygen carrier

  • Abad Secades, Alberto
  • Pérez-Vega, Raúl
  • Diego Poza, Luis F. de
  • Gayán Sanz, Pilar
  • Izquierdo Pantoja, María Teresa
  • García Labiano, Francisco
  • Adánez Elorza, Juan
9 Figures, 6 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, A previously developed manganese-iron mixed oxide doped with TiO2 shows promising properties for the combustion of solid fuels with intrinsic CO2 capture by Chemical Lopping assisted by Oxygen Uncoupling (CLaOU) owing to its oxygen uncoupling capability, i.e. ability to generate gaseous oxygen at high temperature, and to oxidize gaseous fuels such as H2, CO or CH4 by reacting with lattice oxygen. In this work, a window of suitable operating conditions was determined to facilitate the use of this material in a CLaOU unit. For this purpose, mass and enthalpy balances were performed for the whole CLaOU unit considering theoretical values of thermochemical parameters, such as the equilibrium constant of relevant reactions in CLaOU and the formation enthalpies of reacting solids. An air reactor temperature of 1148 K and a high air excess ratio are suggested in order to promote the transfer of oxygen via the oxygen uncoupling mechanism, which would be preferable for the combustion of solid fuels. Auto-thermal operation of the CLaOU unit is guaranteed for air excess ratio values λ < 3. The fuel reactor temperature is highly influenced by the oxygen carrier-to-fuel ratio (ϕ) and the oxygen carrier regeneration in the air reactor. Assuming a 50–75% regeneration of the oxygen uncoupling capability, and ϕ = 4–6, the fuel reactor temperature would be between 35 and 50 K above the air reactor temperature. The higher temperature in the fuel reactor could promote the fuel conversion, while oxygen carrier regeneration would be guaranteed by the lower air reactor temperature., This work was partially supported by the Ministerio de Economía, Industria y Competitividad (Projects: ENE2016-77982-R and ENE2017-89473R), by the Fondo Europeo de Desarrollo Regional (FEDER), and by the Consejo Superior de Investigaciones Científicas (CSIC project: 2017-80E035)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reduction and oxidation kinetics of Fe–Mn-based minerals from southwestern Colombia for chemical looping combustion

  • Velasco-Sarria, Francisco J.
  • Forero, C. R.
  • Arango, Eduardo
  • Adánez Elorza, Juan
8 Figuras, 8 Tablas, The oxygen carrier (OC) is the main component of the chemical looping combustion (CLC), process. Most OCs have been developed synthetically using an active metal oxide combined with an inert material. When solid fuels are used, the OC becomes mixed with the ashes generated during the CLC process and has to be removed, thereby increasing costs. As a result, there is growing interest in the use of low-cost OCs based on manganese and iron. Given the widespread use of coal to produce energy, there is a trend toward the study of the CLC process using solid fuels, since this process has the lowest energy penalties of all the combustion methods involving CO2 capture. Coproducts from the exploitation of Mn and Fe ores have been studied. These materials were selected from a group of eight minerals with Fe and Mn present in their composition, extracted from mines located in southwestern Colombia. The material selection process was based on crushing strength analysis and reactivity in thermographic analysis (TGA), using CH4 as fuel. Two materials were selected, one based on Fe and another based on Mn, which presented the best behavior in their respective group. It was found that the studied two materials were more reactive with H2 and CO than with CH4. This was demonstrated by performing a kinetic study using a shrinking core model (SCM). The selected Mn-based oxide was evaluated to identify whether it had the properties required for chemical looping with oxygen uncoupling (CLOU), commonly found in Mn minerals with a high silica content. However, no evidence to this effect was found in experiments at 1000 °C using N2 for OC decomposition and air as an oxidizing gas. The Mn ore showed the highest reactivity of all the studied materials, with a rate index of 11.9%/min in experiments at 950 °C using H2 as the reducing gas. Finally, it can be concluded that the presence of silica improves the reactivity of the Mn ore, making it a promising carrier for use in in situ gasification chemical looping combustion (iG-CLC) technology., This research was conducted with financial support from Unión Temporal Incombustion (Temporary Joint Working Group) and Colciencias through Recoverable Assistance Agreement RC 0852-2012. We are grateful for the collaboration shown by Instituto de Carboquímica, Zaragoza (Project ENE2016-77982-R and European Regional Development Fund (ERDF))., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Life cycle assessment of natural gas fuelled power plants based on chemical looping combustion technology

  • Navajas, A.
  • Mendiara, Teresa
  • Goñi, Víctor
  • Jiménez Loygorri, Adrián
  • Gandía, L. M.
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
11 Figuras, 2 Tablas.-- Material suplementario disponible en línea en la página web del editor.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Among the different Carbon Capture and Storage (CCS) technologies being developed in the last decades, Chemical Looping Combustion (CLC) stands out since it allows inherent CO2 capture. In the CLC process, there is a solid oxygen carrier circulating between two reactors in a cycle that allows providing the oxygen needed for combustion. In one of the reactors, named as fuel reactor, the fuel is introduced and combusted while the oxygen carrier reduction takes place. In the second reactor, named air reactor, the oxygen carrier is reoxidized in air. Different materials based on copper, nickel and iron oxides have been proposed as oxygen carriers for the CLC process. This work presents an environmental evaluation of the CLC process for natural gas based on Life Cycle Assessment (LCA). Five different oxygen carrier materials already tested in pilot plants were considered and the results compared to the conventional natural gas combustion in a gas turbine in a combined cycle without and with CO2 capture using postcombustion capture with amines. In view of the results, lower impact of the CLC process compared to the base case is expected without and with CO2 capture. The influence of several variables on the results was considered, such as temperature in the air reactor, lifetime of the oxygen carrier and possibility of recuperation of the depleted oxygen carrier. The nickel-based oxygen carriers were identified as the most adequate to be used in natural gas combustion. However, due to their toxicity, several analyses were also performed in order to identify improvements in the known oxygen carriers that can qualify them to replace nickel-based materials., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) [grant numbers ENE2017-89473-R, ENE2016-77982-R] and the European Regional Development Fund (ERDF) under the program “Programa Operativo FEDER Aragón 2014-2020 - Construyendo Europa desde Aragón. Proyecto BiosinCO2 (LMP180_18)”. T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post-doctoral contract awarded by MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Coal combustion via Chemical Looping assisted by Oxygen Uncoupling with a manganese‑iron mixed oxide doped with titanium

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
10 Figures, 4 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical looping combustion allows the carbon dioxide capture by using an oxygen carrier, which transports the oxygen required for combustion from the air to the fuel. But complete combustion of a solid fuel is not achieved when low cost materials were used as oxygen carriers. Manganese‑iron mixed oxide doped with titanium has been identified as a promising oxygen carrier to improve combustion efficiency due to its oxygen uncoupling capability. The objective of this work was to assess the potential of this oxygen carrier when burning coal in a chemical looping unit. The coal combustion efficiency and carbon dioxide capture were evaluated as a function of the operating conditions both in the fuel and air reactor. Carbon dioxide capture was affected by the solids residence time in the fuel reactor. Coal combustion efficiency increased as the oxygen uncoupling capability was enhanced by using suitable operating conditions in the air reactor. Almost full coal combustion (99.4%) was achieved by setting an air reactor temperature of 880 °C, an air excess of 1.8, a fuel reactor temperature of 925 °C, and an oxygen carrier to fuel ratio >3. The oxygen carrier showed magnetic properties, allowing its re-use after being separated from ash., This work was partially supported by the project ENE2016-77982-R (AEI/FEDER, UE) and project ENE2017-89473R (AEI/FEDER, UE), and by the Consejo Superior de Investigaciones Científicas (CSIC project: 2017-80E035)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Biomass combustion with CO2 capture in a 20 kWth CLC plant

  • Pérez-Astray, Antón
  • Pérez-Vega, Raúl
  • Mendiara, Teresa
  • Diego Poza, Luis F. de
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
Presentado en las XXXVI Jornadas Nacionales de Ingeniería Química, JNIQ 2019, Zaragoza, 4-6 Sep. 2019., Bioenergy with Carbon Capture and Storage (BECCS) represents an interesting option to achieve the negative CO2 emissions needed to comply with the climate challenges set in the Paris Agreement (COP21-2015). Chemical Looping Combustion (CLC) technology has revealed as one of the CO2 capture technologies with less energy penalty and lower cost. CLC combined with biomass could become a promising BECCS technology. The objective of this work was to asses the feasibility of the CLC technology using biomass as fuel as a future BECCS technology., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO Projects: ENE2014-56857-R, ENE2016-77982-R and ENE2017-89473-R) and European Regional Development Fund (ERDF). A. Pérez-Astray thanks MINECO for the BES-2015-074651 co-financed by the European Social Fund. T. Mendiara thanks for the “Ramón y Cajal” post-doctoral contract., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Combustión de biomasa sin emisión de CO2 en una planta de 20 kW

  • Pérez-Astray, Antón
  • Pérez-Vega, Raúl
  • Mendiara, Teresa
  • Diego Poza, Luis F. de
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
1 Figura, 2 Tablas.-- Presentado en las XXXVI Jornadas Nacionales de Ingeniería Química, JNIQ 2019, Zaragoza, 4-6 Sep. 2019., El Acuerdo de París fijó el objetivo de limitar en 2 ºC el incremento de temperatura media global sobre los valores preindustriales. Para tal efecto, el IPCC señala a la bioenergía con captura y almacenamiento de CO2 (BECCS en inglés) como una de las tecnologías clave para reducir el impacto del cambio climático pudiendo alcanzarse emisiones negativas de CO2. La implementación de biocombustibles en las tecnologías tradicionales de captura de CO2 implica un alto coste energético del combustible obteniendo una corriente de CO2 prácticamente puro con uno de los menores costes energéticos asociados. El proceso se basa en la utilización de un transportador de oxígeno (TO), normalmente un óxido metálico, que al transportar el oxígeno del reactor de oxidación al de reducción, evita la mezcla del oxígeno del aire y los gases de combustión, evitando de este modo la aplicación de un proceso de separación de gases. En este trabajo se evaluó en una planta piloto de 20 kW de potencia, el efecto de las principales variables de operación bajo condiciones de In situ Gasification-CLC como son la circulación de sólidos, el tipo de agente gasificante y el inventario específico de sólidos en el reactor de reducción sobre los principales parámetros de rendimiento del proceso como son la eficacia de captura de CO2 y la demanda total de oxígeno., Trabajo financiado por el MINECO (ENE2014-56857-R, ENE2016-77982-R, ENE2017-89473-R) y por FEDER. A. Pérez-Astray agradece la beca predoctoral BES-2015-074651., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Kinetics of CaMn0.775Ti0.125Mg0.1O2.9-δ perovskite prepared at industrial scale and its implication on the performance of chemical looping combustion of methane

  • Abad Secades, Alberto
  • Cabello Flores, Arturo
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Mendiara, Teresa
  • Adánez Elorza, Juan
17 figures, 6 tables.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The reaction kinetics of CaMn0.775Ti0.125Mg0.1O2.9-δ perovskite, prepared at ton-scale to be used as an oxygen carrier in a CLC process with methane, was determined. The variation of the reaction rates, oxygen transport capacity, and oxygen uncoupling behaviour of the selected material with the number of cycles was evaluated in a thermogravimetric analyser. The perovskite was activated for the reduction reaction with all the combustible gases, i.e., H2, CO and CH4. On the contrary, the oxidation rate barely changed throughout the cycles. The oxygen transport capacity underwent a slight decrease during the activation period. Kinetics of reduction, oxidation and oxygen uncoupling reactions were determined for the fresh and activated material assuming a grain model controlled by chemical reaction at low values of solids conversion and diffusion through the product layer at high values of solids conversion. This model predicted correctly the solids conversion vs. time curves as a function of temperature and gas concentration for the oxygen carrier reactions evaluated in this kinetics study. The kinetics data were introduced in a validated mathematical model of a fuel reactor to analyse the amount of solids required to fully combust CH4. A solids inventory of 350 kg/MWth was estimated in the fuel reactor at a temperature of 1243 K. However, this value could be reduced to 160 kg/MWth if the material operates under activation conditions within the CLC unit., This work was partially supported by the project ENE2016-77982-R (AEI/FEDER, UE), ENE2017-89473-R (AEI/FEDER, UE) and the SUCCESS Project, funded by the European Commission under the Seventh Framework Programme (Grant agreement No. 608571 )., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of different strategies to improve the efficiency of coal conversion in a 50 kWth Chemical Looping combustion unit

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Pérez-Vega, Raúl
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Mendiara, Teresa
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
6 Figures, 3 Tables.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Minerals or industrial waste materials are considered promising oxygen carriers for coal combustion through in-situ Gasification Chemical Looping Combustion (iG-CLC) process in order to maintain CO2 capture at low cost. Nevertheless, complete coal combustion to CO2 and H2O is usually not achieved and different solutions have been outlined to improve it. The aim of this work is to analyze the potential of two of these strategies: (1) using a more reactive oxygen carrier; and (2) to have two fuel reactors by feeding the coal into the carbon stripper. Coal combustion in a 50 kWth CLC unit was carried out using two oxygen carrier materials, namely Norwegian ilmenite and Tierga iron-ore. Also, an additional test was carried out feeding the coal directly into the carbon stripper of the CLC unit, in contrast with the conventional coal feeding to the fuel reactor. CO2 capture efficiency was barely affected by the type of oxygen carrier material, but slightly lower values were obtained when coal was fed to the carbon stripper. In contrast, coal combustion efficiency was enhanced by using the iron-ore material, with a potential decrease of the total oxygen demand of 40%, achieving a minimum value of total oxygen demand of 4.1%. Also, the total oxygen demand was decreased by 24% when coal was fed to the carbon stripper due to the improvement in the combustion of the volatiles in the fuel reactor. The combination of both strategies has high potential to maximize the coal combustion via iG-CLC process., This work was partially supported by the Ministerio de Economía y Competitividad (project ENE2014-56857-R), and by the projects ENE2016-77982 (AEI/FEDER, UE), and ENE2017-89473-R (AEI/FEDER, UE), by the Regional Aragon Government via the T05_17R research group funding and by the Consejo Superior de Investigaciones Científicas (CSIC project: 2017-80E035). T. Mendiara thanks for the “Ramón y Cajal” post-doctoral contract awarded by MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

CO2 capture by Chemical Looping Processes using C-fuels

  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Adánez Elorza, Juan
1 figure.-- Work presented at the Carbon 2018 ´"The World Conference of Carbon", Madrid (Spain), 01st-6th July, According to the IPCC, warming of the climate system is unequivocal and this is mainly consequence of the increase in the CO2 concentration in the atmosphere. In addition, “Human influence on the climate system is clear, and recent anthropogenic emissions of greenhouse gases are the highest in history”. These emissions are mainly consequence of the burning of C-fuels, mostly fossil fuels, which result in a net increase in carbon concentration in the atmosphere, soil and oceans. In fact, the natural carbon cycle in the earth is being affected. Limiting climate change would require substantial and sustained reductions in greenhouse gas emissions. The measures considered for the reduction of CO2 emissions to the atmosphere include the improvement in the use and generation of energy, the use of nuclear energy, the boost of energy generation from renewable sources and the CO2 capture and storage (CCS)., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (projects ENE2014-56857-R, ENE2016-77982-R, and ENE2017-89473-R), by the European Regional Development Fund (ERDF), by the CSIC (201780E035), and by the Government of Aragón. T. Mendiara thanks for the “Ramón y Cajal” post-doctoral contract awarded by MINEICO.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel magnetic manganese-iron materials for separation of solids used in high-temperature processes: Application to oxygen carriers for chemical looping combustion

  • Abad Secades, Alberto
  • Pérez-Vega, Raúl
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
6 figures, 3 tables.-- Supplementary information available., Different chemical looping processes allow burning or gasify solid fuels with inherent CO2 capture because the oxygen is transferred from air to the fuel through a metal oxide based material, which is named oxygen carrier. To improve process efficiency and CO2 capture, highly reactive synthetic materials could be used. One of the challenges of using solid fuels is the oxygen carrier separation from the ash, because loss of oxygen carrier particles is expected during ash drainage. So, their costs would have necessary the recovery of the synthetic oxygen carrier. Mn-Fe based materials show magnetic properties in the spinel phase, which could be used for a magnetic separation. When these Mn-Fe materials are used at high temperature under oxidizing or reducing atmospheres, stability of the spinel phase should be guaranteed in order to take advantage of the magnetic properties. The design of low reactive Mn-Fe based materials with magnetic properties, which can be used as a support material for other highly reactive and active phases, was the main objective of this work. In this sense, the support must have high crushing strength, low reactivity under oxidation and reduction atmospheres at high temperatures and permanent magnetism at low temperature for solids separation. Materials prepared with different Mn/(Mn + Fe) molar ratios and calcination conditions were evaluated regarding mechanical strength, inerticity and magnetic properties. A Cu-based oxygen carrier prepared on the optimal support was prepared and evaluated along 240 oxidation-reduction cycles in thermobalance (25 h experiment), exhibiting suitable mechanical and magnetic characteristics as well as high reactivity., This work has been supported by the AEI/FEDER, UE ENE2016-77982-R, ENE2017-89473-R and ID2019-106441RB-I00 projects, and by the Regional Aragon Government via the T05_17R research group funding., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CLOU process performance with a Cu-Mn oxygen carrier in the combustion of different types of coal with CO2 capture

  • Adanez-Rubio, I.
  • Abad, A.
  • Gayan, P.
  • de Diego, L.F.
  • Adanez, J.
The Chemical Looping with Oxygen Uncoupling (CLOU) process is a Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with inherent CO2 separation by using oxygen carriers based on metal oxides. This technology has a low energy penalty and thus low CO2 capture costs. The oxygen carrier used in the CLOU process must be able to release gaseous oxygen, an aspect that limits the availability of metal oxides for this process. This work investigated the suitability of an oxygen carrier containing 34 wt% CuO and 66 wt% Mn-3 O-4 (active phase Cu1.5Mn1.5O4) prepared by granulation regarding the CO2 capture, combustion efficiency and lifetime of the particles. The effect of the different types of coal (two sub-bituminous and a lignite) on combustion and CO2 capture efficiencies by CLOU was studied at different oxygen carrier to coal ratios in a continuous 1.5 kWth rig. It was found that full combustion could be reached regardless of the coal used. However, CO2 capture efficiencies were highly determined by coal rank. Finally, it was found that working with oxygen carrier to coal ratios higher than phi = 4, which corresponded to values of the variation of the oxygen carrier conversion lower than Delta X-oc = 0.25, decreased the effect of chemical stress on the attrition rate. Therefore, it is clearly beneficial for the lifetime of oxygen carrier particles to operate with low variations of the oxygen carrier conversion (Delta X-oc) between fuel and air reactors.