Pasar al contenido principal

LUBRICANTES BASADOS EN NANOADITIVOS AVANZADOS PARA ENGRANAJES Y MOTORES

ENE2017-86425-C2-2-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDADE DE SANTIAGO DE COMPOSTELA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Electrochemically exfoliated graphene and molybdenum disulfide nanoplatelets as lubricant additives

  • García Guimarey, María Jesús
  • Viesca Rodríguez, José Luis
  • Abdelkader, Amr
  • thomas, ben
  • Hernández Battez, Antolin
  • Hadfield, Mark
In this work, two different 2D materials, molybdenum disulfide nanoplatelets (MSNP) and graphene nanoplatelets (GNP), prepared by electrochemical exfoliation, were used as additives to prepare nanolubricants. The tribological behaviour of the nanolubricants was evaluated under two configurations (pure sliding and rolling/sliding) using two different tribometers: an Universal Macro Materials Tester (UMT-3) and a Mini Traction Machine (MTM2). Wear volume was determined, after the sliding tests, in a confocal microscope (Leica DCM 3D) and the worn surface was analyzed by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and Raman microscopy. Lubrication mechanisms of GNP and MSNP dispersed in an engine oil for improving its antifriction and antiwear capabilities are proposed. The traction coefficient determination was performed at a 50% of slide-to-roll ratio and at different temperatures. The results showed that the nanolubricants formulated with both types of additives, in their lowest concentration, improved friction and wear in sliding tests, compared to neat engine oil. In addition, only the nanolubricants with the MSNP nano additive at loadings of 0.05 and 0.2 wt% showed friction reductions compared to the commercial engine oil under the rolling/sliding test
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Heat capacity, density, surface tension, and contact angle for polyalphaolefins and ester lubricants

  • Coelho de Sousa Marques, Mónica Alexandra
  • García Guimarey, María Jesús
  • Domínguez Arca, Vicente
  • Amigo Pombo, Alfredo José
  • Fernández Pérez, Josefa
Thermophysical properties of lubricants are important to understand which ones are appropriated for the industrial conditions expected. Thermophysical properties of two different families of lubricants were analysed: polyalphaolefins (PAO6, PAO20, PAO32 and PAO40) and four ester-based lubricants. Specific heat capacity, density, surface tension, and contact angle were experimentally determined over a broad temperature range through methods such as μDSC, U-tube vibration, drop volume, and sessile drop method, respectively. A clear difference between the two families was observed due to their structure and composition, grouping by nature. Ester-based lubricants showed lower specific heat capacity but higher surface tension and density than polyalphaolefins. PAO6 clearly has the lowest density and surface tension and presents the highest specific heat capacity of all lubricants, and together with trimethylolpropane trioleate, TMPTO, presents the best wettability. Heat capacity values were used to test the validity of two predictive methods
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

ZnO nanoparticles coated with oleic acid as additives for a polyalphaolefin lubricant

  • Mariño Fernández, Fátima
  • López Iglesias, Enriqueta
  • Arnosa Prieto, Ángela
  • González Gómez, Manuel Antonio
  • Piñeiro Redondo, Yolanda
  • Rivas Rey, José
  • Álvarez Lorenzo, Carmen
  • Fernández Pérez, Josefa
In this work, ZnO nanoparticles (NPs) were successfully synthesized and coated with oleic acid (OA). The mean diameter of these NPs (ZnO-OA) was around 11.5 nm, their core was characterized by XRD and their coating by FTIR and Raman. Homogeneous dispersions at different concentrations (0.10, 0.25, 0.50, 0.75 and 1.00 wt%) of ZnO-OA in polyalphaolefin 40 (PAO40) oil were thermophysically and tribologically characterized. Both density and viscosity values increased with the concentration of NPs, reaching relative increments of 0.5% and 4.0%, respectively, for the 1 wt% nanodispersion. Tribological tests were performed at 353.15 K using an Anton Paar MCR 302 rheometer equipped with a tribological ball-on three-pins configuration testing module. Regarding the tribological behavior, the optimal concentration was 0.25 wt% of ZnO-OA (25% of reduction in the friction coefficient and 82% wear reduction in terms of cross sectional area, respect to those obtained with the neat base oil). The rolling mechanism owing to the spherical shape of the nanoadditives, transforming sliding friction into rolling friction, and the mending effect could explain the better tribological performance of nanolubricants with respect to that of neat PAO40. In addition, the presence of PAO40, ZnO-OA NPs and iron oxides was evidenced from confocal Raman microscopy on the worn surfaces obtained from tribological test with PAO40 + 0.25 wt% ZnO-OA dispersion
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Synergistic effects of hexagonal boron nitride nanoparticles and phosphonium ionic liquids as hybrid lubricant additives

  • Nasser, Khodor I.
  • Liñeira del Río, José Manuel
  • López Iglesias, Enriqueta
  • Fernández Pérez, Josefa
Hybrid nanostructure combinations of ionic liquids (ILs) and hexagonal boron nitride (h-BN) nanosheets are proposed as additives to lubricants to enhance their tribological performance and their temporal stability. Trihexyltetradecylphosphonium bis(2-ethylhexyl)phosphate (IL1), tributylethylphosphonium diethylphosphate (IL2) and trihexyltetradecylphosphonium bis(2,4,4-trimethylpentyl)phosphinate (IL3) are the ILs (at 1 wt%) that have been combined, each separately, with h-BN nanosheets (at 0.1 wt%), were added as hybrid additives in a polyalphaolefin base lubricant, PAO 32. Some of the nanodispersions remain stable up to 240 days after preparation. Increases in both viscosity and density owing to h-BN nanoparticles and/or ILs are lower than 7% and 0.3%, respectively. The tribological performance (friction and wear) of the several developed nanolubricants were investigated using a tribometer with a ball-on-three-pin configuration and a 3D optical profiler, respectively. The results showed that the hybrid additives improve, in general, the tribological performance of the lubricant rather than being used separately, thus synergistic effects have been found. Raman spectroscopy conducted on the worm surface showed protective IL and h-BN tribofilms. PAO 32 + IL1 + h-BN is the nanolubricant that exhibits the best tribological performance of those studied in this work.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Tribological synergies among chemical-modified graphene oxide nanomaterials and a phosphonium ionic liquid as additives of a biolubricant

  • Liñeira del Río, José Manuel
  • López Iglesias, Enriqueta
  • García, Fátima
  • Fernández Pérez, Josefa
In the present work, antifriction and antiwear synergies of two functionalized graphene oxides (reduced graphene oxide, rGO, and reduced graphene oxide modified with octadecylamine, rGO@ODA) with a phosphonium ionic liquid (IL) as additives of a biodegradable ester base oil, BIOE, were investigated. For this aim, four BIOE nanodispersions were formulated: two nanodispersions without IL and two others with IL (hybrid nanolubricants), being the nanodispersions: BIOE + 0.05 wt% rGO, BIOE + 0.05 wt% rGO@ODA, BIOE + 1 wt% IL + 0.05 wt% rGO and BIOE + 1 wt% IL + 0.05 wt% rGO@ODA, and all of them showing good temporal stability (at least 3 weeks), especially those containing the ionic liquid. Tribological tests, under pure sliding conditions, were made with the aforementioned nanolubricants and with neat BIOE under a 20 N working load. All hybrid and non-hybrid nanolubricants resulted in lower friction coefficients compared to BIOE oil, with the largest friction reduction of 34% achieved by the 1 wt% IL + 0.05 wt% rGO nanolubricant. Discs lubricated with the prepared nanolubricants showed less wear than discs lubricated with BIOE, achieving the highest reduction (34%) in wear track width also for the 1 wt% IL + 0.05 wt% rGO nanolubricant. In addition, through confocal Raman microscopy, as well as roughness analysis of tested discs, it can be concluded that surface repairing, synergistic effect and tribofilm formation mechanisms occur.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Double hybrid lubricant additives consisting of a phosphonium ionic liquid and graphene nanoplatelets/hexagonal boron nitride nanoparticles

  • Nasser, Khodor I.
  • Liñeira del Río, José Manuel
  • Mariño Fernández, Fátima
  • López Iglesias, Enriqueta
  • Fernández Pérez, Josefa
Tribological performance of polyalphaolefin 32, PAO, is investigated by adding two nanomaterials (graphene nanoplatelets, GnP, and hexagonal boron nitride nanoparticles, h-BN) and an ionic liquid ([P6,6,6,14][DEHP], IL1, [P2,4,4,4][DEP], IL2, or [P6,6,6,14][(iC8)2PO2], IL3). Designed double hybrid nanodispersions are PAO/1 wt% ILX/0.05 wt% GnP/0.1 wt% h-BN (X = 1, 2 or 3). The best anti-friction behavior corresponds to PAO/IL3/GnP/h-BN (40% reduction compared to that achieved with PAO). Anti-wear behavior is similar for the three double hybrid nanodispersions. Roughness of the worn surface tested with PAO is higher than that obtained for each of the nanodispersions. Tribo-film formation and repair effect on worn surfaces due to ILs and nanoparticles are revealed. Some positive synergies were found between each IL and GnP/h-BN as hybrid PAO additives
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Improvement of the lubrication performance of an ester base oil with coated ferrite nanoadditives for different material pairs

  • García Guimarey, María Jesús
  • Liñeira del Río, José Manuel
  • Fernández Pérez, Josefa
In the present work, lubrication properties (friction and wear) of a synthetic ester oil, tris(2-ethylhexyl) trimellitate (TOTM) containing ferrite nanoparticles coated with oleic acid (F3O4-OA) were investigated for two different material pairs: steel ball-steel disc and silicon nitride ball-steel disc. Thus, four TOTM nanolubricants were formulated: TOTM + 0.010 wt% Fe3O4-OA, TOTM + 0.015 wt% Fe3O4-OA, TOTM + 0.020 wt% Fe3O4-OA and TOTM + 0.025 wt% Fe3O4-OA showing all of them a moderate time stability due to the oleic acid coating. Wettability behaviour of the ferrite-based nanolubricants on steel surface was analysed, revealing that the addition of Fe3O4-OA nanoparticles in TOTM decreases the contact angle between the steel surface and TOTM lubricant surface. Friction sliding tests were performed with the neat TOTM and with the formulated nanolubricants under a 20 N of load. All nanolubricants showed lower coefficients of friction than those reached with TOTM base oil for both material pairs. Worn area was significantly reduced for all Fe3O4-OA concentrations in the steel-steel contact and for the highest concentrations in the silicon nitride-steel contact. Specifically, the largest achieved reductions were for the TOTM + 0.010 wt% F3O4-OA nanolubricant: 43% reduction in friction (silicon nitride-steel) and reductions of 17% in wear track width, 42% in wear track deep and 36% in area (steel-steel). In addition, roughness analysis and Raman microscopy of the tested discs showed that tribofilm formation and surface repairing mechanisms occur
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Experimental investigation of tribological and rheological behaviour of hybrid nanolubricants for applications in internal combustion engines, Río, J.M.L. del, Rial, R., Nasser, K. et al. Experimental Investigation of Tribological and Rheological Behaviour of Hybrid Nanolubricants for Applications in Internal Combustion Engines. Tribol Lett 71, 25 (2023). https://doi.org/10.1007/s11249-023-01697-5

  • Liñeira del Río, José Manuel
  • Rial Silva, Ramón
  • Nasser, Khodor I.
  • García Guimarey, María Jesús
In this study, the improvement in SAE 10W-40 engine oil tribological performance after the addition of magnesium oxide (MgO) nanoadditive and two different phosphonium-based ionic liquids (ILs) was investigated. Besides, the rheological behaviour of MgO-based nanolubricant and IL-based hybrid nanolubricants at the temperature range from 293.15 to 363.15 K was studied. The nanoparticle characterization was performed by means of transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The tribological properties, friction coefficients and wear parameters of the formulated oil modified with 0.01 wt% MgO and 1 wt% ILs compared with the neat 10W-40 oil were performed and analysed using a ball-on-three-pins tribometer and a 3D optical profilometer, respectively. Further analysis on the worn surface was shown by Raman spectroscopy and SEM images illustrating the formation of the protective IL and MgO tribo-films as hybrid additives. In friction tests with sliding steel-steel tribo-pairs, IL3-based hybrid nanolubricant decreased the coefficient of friction and wear volume by 7% and 59%, respectively, in comparison with the neat SAE 10W-40, hence better positive synergies were found for MgO and IL3 as hybrid additives. Interestingly, the thermophysical characterization by rheology also revealed that the nanoparticle and ionic liquids addition did not affect neither the viscosity response nor the Newtonian behaviour of the engine oil, adequately meeting the requirements for their use in internal combustion engines
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Lubricant properties of trimethylolpropane trioleate biodegradable oil: High pressure density and viscosity, film thickness, Stribeck curves and influence of nanoadditives

  • García Guimarey, María Jesús
  • Gonçalves, David E. P.
  • Liñeira del Río, José Manuel
  • Pérez Comuñas, María José
  • Fernández Pérez, Josefa
  • Seabra, Jorge H. O.
Lubricant properties of trimethylolpropane trioleate synthetic base oil (TMPTO) were experimentally determined under different temperatures, pressures and rolling-sliding conditions. With the aim to obtain the viscosity-pressure coefficient, density and viscosity measurements were performed up to 150 MPa with a falling-body viscometer and a vibrating tube densimeter, respectively. Film thickness and friction properties were determined with a ball-on-disc apparatus from temperatures of 303.15 to 353.15 K, from slide-roll ratios from 5 to 50% at 50 N (applied load). Finally, it has also been evaluated if the use of nanoparticles as additives could involve changes on film thickness and Stribeck curves of TMPTO base oil. For this aim, hexagonal-boron nitride nanoparticles (h-BN) and graphene nanoplatelets (GnPs) were used at mass concentrations of 0.25, 0.5 and 1.0 wt%. The viscosity of TMPTO increases from 15 mPa s (at 10 MPa and 353.15 K) to 525 mPa s (at 150 MPa and 303.15 K). The Stribeck curves for TMPTO are placed between elastohydrodynamic and mixed lubrication. All nanolubricants show very similar Stribeck curves, being the lowest friction coefficient obtained for 0.25 wt% of GnP. It has been found that for most of the experimental conditions the addition of the GnP promotes an increase of the film thickness
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Tribological enhancement using Mn3O4-Graphene nanocomposites as additives for potential transmission fluids of electric vehicles

  • Liñeira del Río, José Manuel
  • Rial Silva, Ramón
  • López Iglesias, Enriqueta
  • Fernández Pérez, Josefa
This research reports the antifriction and antiwear properties of Mn3O4-Graphene nanocomposites (Mn3O4-G) as additives of a paraffinic base oil commonly used in the formulation of electric vehicles transmission oils, G-III base oil. Four G-III base oil nanodispersions have been designed, G-III base oil + 0.025 wt% Mn3O4-G, G-III base oil + 0.050 wt% Mn3O4-G, G-III base oil + 0.075 wt% Mn3O4-G and G-III base oil + 0.100 wt% Mn3O4-G, to know the optimal concentration of nanoadditive. Tribological experiments were carried out with these nanolubricants and with neat G-III base oil at pure sliding conditions under a working load of 9.43 N. All tested nanolubricants led to similar friction coefficients in comparison to that obtained using G-III base oil. Tribological specimens tested with formulated nanolubricants revealed less wear than that obtained with G-III base oil, obtaining the greatest wear reduction using the G-III base oil + 0.075 wt% Mn3O4-G nanolubricant, with reductions of 25, 50 and 64% in wear scar diameter, maximum depth and transversal area, respectively. Moreover, by means of confocal Raman microscopy and roughness evaluation of worn tribological specimens, it was concluded that synergetic effect, tribofilm formation and rolling mechanisms happen