Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Tailoring of AlAs/InAs/GaAs QDs Nanostructures via Capping Growth Rate

  • Ruiz Marín, Nazaret
  • Fernández de los Reyes, Daniel
  • Luna, Esperanza
  • Stanojevic, Lazar
  • Ben Fernández, Teresa
  • Flores Gallegos, Sara
  • Braza Blanco, María Verónica
  • Gallego-Carro, A.
  • Barcena González, Guillermo
  • Yañez Escolano, Andrés
  • Ulloa, José María
  • González Robledo, David
The use of thin AlA capping layers (CLs) on InAs quantum dots (QDs) has recently received considerable attention due to improved photovoltaic performance in QD solar cells. However, there is little data on the structural changes that occur during capping and their relation to different growth conditions. In this work, we studied the effect of AlA capping growth rate (CGR) on the structural features of InAs QDs in terms of shape, size, density, and average content. As will be shown, there are notable differences in the characteristics of the QDs upon changing CGR. The Al distribution analysis in the CL around the QDs was revealed to be the key. On the one hand, for the lowest CGR, Al has a homogeneous distribution over the entire surface, but there is a large thickening of the CL on the sides of the QD. As a result, the QDs are lower, lenticular in shape, but richer in In. On the other hand, for the higher CGRs, Al accumulates preferentially around the QD but with a more uniform thickness, resulting in taller QDs, which progressively adopt a truncated pyramidal shape. Surprisingly, intermediate CGRs do not improve either of these behaviors, resulting in less enriched QDs.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Identification of the Segregation Kinetics of Ultrathin GaAsSb/GaAs Films Using AlAs Markers

  • González Robledo, David
  • Flores Gallegos, Sara
  • Braza Blanco, María Verónica
  • Fernández de los Reyes, Daniel
  • Gallego Carro, Alejandro
  • Stanojev´c, Lazar
  • Schwarz, Malte
  • Ulloa, Jose María
  • Ben Fernández, Teresa
For optoelectronic devices from the near to the far infrared, the advantages of using ultrathin III-Sb layers as quantum wells or in superlattices are well known. However, these alloys suffer from severe surface segregation problems, so that the actual profiles are very different from the nominal ones. Here, by inserting AlAs markers within the structure, state-of-the-art transmission electron microscopy techniques were used to precisely monitor the incorporation/segregation of Sb in ultrathin GaAsSb films (from 1 to 20 monolayers (MLs)). Our rigorous analysis allows us to apply the most successful model for describing the segregation of III-Sb alloys (three-layer kinetic model) in an unprecedented way, limiting the number of parameters to be fitted. The simulation results show that the segregation energy is not constant throughout the growth (which is not considered in any segregation model) but has an exponential decay from 0.18 eV to converge asymptotically towards 0.05 eV. This explains why the Sb profiles follow a sigmoidal growth model curve with an initial lag in Sb incorporation of 5 MLs and would be consistent with a progressive change in surface reconstruction as the floating layer is enriched.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Growth interruption strategies for interface optimization in GaAsSb/GaAsN type-II superlattices

  • Braza Blanco, María Verónica
  • Ben Fernández, Teresa
  • Flores Gallegos, Sara
  • Fernández de los Reyes, Daniel
  • Gallego-Carro, A.
  • Stanojevic, L.
  • Gacevic, Z.
  • Ruiz Marín, Nazaret
  • Ulloa, J.M.
  • González Robledo, David
Recently, GaAsSb/GaAsN type II short-period superlattices (SLs) have been proposed as suitable structures to be implemented in the optimal design of monolithic multi-junction solar cells. However, due to strong surface Sb segregation, experimental Sb composition profiles differ greatly from the nominal square-wave design. In this work, the improvement of the interface quality of these SLs in terms of compositional abruptness and surface roughness has been evaluated by implementing different growth interruption times under Sb4/As4 (soaking) and As4 (desorption) overpressure conditions before and after the growth of GaAsSb layers, respectively. The com-bined effects of both processes enhance Sb distribution, achieving squarer compositional profiles with reduced surface roughness interfaces. It has been found that the improvement in compositional abruptness is quantita-tively much higher at the lower interface, during soaking, than at the upper interface during desorption. Conversely, a larger decrease in surface roughness is achieved at the upper interface than at the lower interface. Fitting of the Sb segregation profiles using the 3-layer kinetic fluid model has shown that the increase in Sb incorporation rate is due to the decrease in segregation energy, presumably to changes in the surface recon-struction of the floating layer at the surface.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Effect of MBE growth conditions on GaAsBi photoluminescence lineshape and localised state filling

  • Bailey, N.J.
  • Rockett, T. B. O.
  • Flores Gallegos, Sara
  • Fernández de los Reyes, Daniel
  • David, J. P. R.
  • Richards, R. D.
A series of gallium arsenide bismide device layers covering a range of growth conditions are thoroughly probed by low-temperature, power-dependent photoluminescence measurements. The photoluminescence data is modelled using a localised state profile consisting of two Gaussians. Good agreement with the raw data is achieved for all layers whilst fixing the standard deviation values of the two Gaussians and constraining the band gap using X-ray diffraction data. The effects of growth temperature and bismuth beam equivalent pressure on the localised state distributions, and other model variables, are both shown to be linked to emission linewidth and device properties. It is concluded that bismuth rich surface conditions are preferable during growth in order to produce the narrowest emission linewidths with this material. These results also show how the growth mode of a gallium arsenide bismide layer can be inferred ex-situ from low-temperature photoluminescence measurements., The authors would like to gratefully acknowledge Prof Stephen Sweeney and Dr Tom Wilson for useful discussions on modelling and localised states in GaAsBi. This work has been supported by an EPSRC Grant (EP/S036792/1), the Spanish National Research Agency (AEI Projects PID2019-106088RB-C33), Regional Government of Andalusia (Project FEDER-UCA18-108319). The work of RDR was supported by the Royal Academy of Engineering under the Research Fellowships scheme
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Effect of the AlAs capping layer thickness on the structure of InAs/GaAs QD

  • Ruiz Marín, Nazaret
  • Fernández de los Reyes, Daniel
  • Stanojevic, L.
  • Ben Fernández, Teresa
  • Braza Blanco, María Verónica
  • Gallego-Carro, A.
  • Barcena González, Guillermo
  • Ulloa, J.M.
  • González Robledo, David
Recently, very thin AlAs capping layers (CLs) have been proposed as a useful tool to increase the performance of InAs/GaAs quantum dot (QDs) devices. However, the structure of QDs after AlAs deposition remains poorly understood and the mechanisms to explain it are often contradictory. In this work, the structural and compositional changes of InAs QDs using different AlAs CL thicknesses have been studied by state-of-the-art STEM-related techniques. First, the heights and In contents of InAs QDs progressively increase with the CL thickness, demonstrating that the AlAs capping produces a strong shielding effect against the decomposition of QDs. However, QD populations for CL thicknesses above 5 ML split into a bimodal distribution in which smaller lenticular QDs cohabit with bigger truncated pyramids. Second, the actual Al contents around the QDs are well below the nominal design, but increasing for thicker CLs. Its distribution is initially non-uniform, tending to accumulate on the flanks of the QDs to the detriment of the apex. Only for thicknesses above 2 ML the Al contents around the QDs start to be similar to those in the regions between the QDs, behaving as a continuous film without irregularities from 5 ML onwards. © 2021 The Author(s), The work has been co-financed by the Spanish National Research Agency (AEI projects MAT2016-77491-C2-2-R and PID2019-106088RB-C33), Regional Government of Andalusia (project FEDER-UCA18-108319) and the European Regional Development Fund (ERDF).