Pasar al contenido principal

Low-carbon concrete design optimised for 3-D printing. Control of early-age properties

FJC2021-047024-I

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Desarrollar, Atraer y Retener Talento
Subprograma Subprograma Estatal de Formación
Convocatoria Juan de la Cierva Formación
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDADE DA CORUÑA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Optimisation of the performance of alkali-activated mortars using CDW binders from different sources

  • Cantero, B.
  • Neves, Renato
  • Sequeira, Lucas
  • de Brito, J
  • Bravo, Miguel
[Abstract:] This study investigates the fresh-state properties and the hardened-state physical and mechanical properties of a total of 64 alkali-activated mortars incorporating different wastes as binders, such as fly ash (FA), recycled concrete (RC), recycled brick (RB), and recycled tile (RT). These waste materials were activated using sodium hydroxide (NaOH) and sodium silicate (Na2SiO3). Linear regression analysis was employed to evaluate the impact and significance of Na2O concentration (9 % or 15 %), modulus of silica (0.5 or 1), curing time in the oven (24 or 48 h), and temperature (50 °C or 70 °C) on the properties of the mortars. The results, analysed using ANOVA, indicate that all properties were affected by these parameters, except for the initial curing time in the oven for mortars made with construction and demolition waste (CDW), which showed no significant differences between periods of 24 and 48 h. Compared to mortars produced with RC, the contribution of these parameters to mechanical properties was more prominent in the mixes with RT and RB. The highest compressive strength at 28 days, for the mortars with CDW binders, was obtained by incorporating RT with 12 % of Na2O, modulus of silica of 1 and 70 °C for 48 h of initial curing, reaching 12.5 MPa. This value is 2.1 times higher than the strength obtained in mixes with RB or RC. The results also show that the performance of the mortars is highly related to the reactivity of the waste material (mortars with RT performed better) and prove that each raw material has its own optimum criterion., The first author wishes to acknowledge the mobility support received through the Ibero-American Research Scholarships Program 2020/21 of the Santander Foundation for conducting a research stay at the Instituto Superior Técnico de Lisboa (IST). The first author also wishes to thank the Spanish Ministry of Research, Science and Universities for financial support through the postdoctoral program for Juan de la Cierva-training contracts 2021 (No. FJC2021-047024-I). The authors acknowledge the support of Civil Engineering Research and Innovation for Sustainability (CERIS), IST, and the University of Lisbon in the framework of project UIDB/04625/2020 funded by FCT (DOI: 10.54499/UIDB/04625/2020)., Portugal. Fundação para a Ciência e a Tecnologia; UIDB/04625/2020
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Self-Healing Mechanisms in Concrete Cured in CO₂-Saturated Environments: Synergistic Effects of Biomass Forest Ash and Metakaolin

  • Cantero, B.
  • Seara Paz, Sindy
  • Cuenca, E.
  • Ferrara, Liberato
  • González-Fonteboa, Belén
[Abstract]: This study investigates the effect of autogenous self-healing in high-performance ternary concrete mixes incorporating biomass forest ash when exposed to concentration of carbon dioxide (CO₂). To analyse this phenomenon, three cementitious systems were studied: i) 100 % Portland cement, ii) 60 % Portland cement, 25 % biomass ash, and 15 % metakaolin, and iii) 60 % Portland cement, 25 % limestone filler, and 15 % metakaolin. The samples, prepared with different initial crack widths, were subjected to four self-healing conditions: i) continuous immersion in tap water (TW), ii) wet-dry cycles in TW, iii) continuous immersion in carbonated water (CW), and iv) wet-dry cycles in CW, over two exposure periods (28 and 90 days). The effectiveness of the process was evaluated through the analysis of surface crack sealing using a digital microscope and the recovery of impermeability through water permeability tests. To understand the chemical mechanisms involved, the self-healing products formed were analysed using SEM. The results showed that the samples self-healed in CW tended to exhibit lower surface sealing efficiency compared to TW, regardless of the mix type, due to the slightly acidic pH caused by the dissolution of CO₂ into carbonic acid. However, in the higher pH inside the cracks promoted the precipitation of calcium carbonates, improving internal impermeability even without achieving effective surface sealing. In this context, biomass ash was particularly effective as a water reservoir, promoting more efficient internal curing when combined with metakaolin and achieving better results in terms of internal impermeability than conventional mixes with cement or limestone filler combined with metakaolin., This research has been funded by the following projects, which contributed to the development of this study: NanoBioCell: Nano-engineering of Sustainable High-Performance Cementitious Materials Using Biomass-Derived Nanocellulose [PDC2023-151636B-I00], funded by the Spanish Ministry of Science, Innovation and Universities. The first author gratefully acknowledges the financial support received through the “Juan de la Cierva-Formación” programme 2021 (No. FJC2021-047024-I), funded by the same ministry, which has supported his participation in this work. He also expresses his gratitude to the "José Castillejo" Programme for Mobility Stays Abroad (Grant No. CAS22/00481), which enabled him to undertake a research stay at the Dipartimento di Ingegneria Civile e Ambientale - Politecnico di Milano. Finally, the authors acknowledge the technical support provided by the Centro de Innovación Tecnológica en Edificación e Ingeniería Civil (CITEEC).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Comparative Assessment of Binary Alkali-Activated Mortars Incorporating Construction and Demolition Waste under Dry and CO₂ Curing Conditions

  • Cantero, B.
  • Sequeira, Lucas
  • Brito, Jorge de
  • Bravo, Miguel
[Abstract]: Construction and demolition waste (CDW) has attracted increasing attention as a potential precursor for alkali-activated materials, although its heterogeneous nature often limits mechanical performance. This study investigates the behaviour of binary alkali-activated mortars manufactured with different types of CDW: recycled concrete (RC), recycled brick (RB) and recycled tile (RT). The combination of these precursors with 30% fly ash (FA) as a supplementary precursor was also investigated. The mixes were subjected to two curing conditions—dry and CO₂—in order to evaluate the influence of precursor mineralogy and curing regime on their mechanical and physical performance. Compressive and flexural strengths, dynamic modulus of elasticity, ultrasonic pulse velocity (UPV), porosity, shrinkage and carbonation depth were determined. The results showed that precursor reactivity governs the overall behaviour. Tile-based systems (RT) achieved the highest strengths and lowest water-accessible porosity, followed by RB, whereas RC exhibited limited reactivity. Under CO₂ curing, RT70 reached 20.3 MPa at 28 days, representing a 53.9% increase compared to dry curing. In addition, CO₂ curing reduced water-accessible porosity by up to 15%. For a comparable compressive strength, CO₂-cured mixes exhibited higher flexural strength and dynamic modulus of elasticity than those cured under dry conditions. In contrast, RC systems showed a 21.5% reduction in compressive strength at 28 days under CO₂ curing, indicating that early carbonation may adversely affect low reactivity, calcium-rich residues. The incorporation of 30% FA mitigated this effect, increasing the 28-day compressive strength under CO₂ curing from 7.7 MPa (RC100) to 14.3 MPa (RC70). Correlation analysis confirmed an exponential relationship between mechanical performance and water-accessible porosity, highlighting the governing role of pore structure. Overall, the combined use of FA and controlled CO₂ curing offers a viable strategy for enhancing selected CDW-based alkali-activated systems., The first author also wishes to thank the Spanish Ministry of Research, Science and Universities for the financial support provided through the Juan de la Cierva–Formación postdoctoral programme (2021 call, Grant No. FJC2021–047024-I). The authors gratefully acknowledge the support of the Spanish Ministry of Science and Innovation and the Agencia Estatal de Investigación (AEI, Spanish State Research Agency) for funding the project NanoBioCell: Nanoengineering of Sustainable and High-Performance Cementitious Materials Using Biomass-Derived Nanocellulose (Grant No. PDC2023–151636B-I00). This research was funded in part by the Fundação para a Ciência e a Tecnologia, I.P. (FCT, https://ror.org/00snfqn58) under Grant UID/6438/2025 (https://doi.org/10.54499/UID/06438/2025) of the research unit CERIS. Technical support provided by the Centro de Innovación Tecnológica en Edificación e Ingeniería Civil (CITEEC) is also acknowledged., Portugal. Fundação para a Ciência e a Tecnologia; UID/6438/2025
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Assessment of Water Transport and Chemical Attack of Meta-Illite Calcined Clay Blended Cement in High-Performance Concrete

  • Nduka, David
  • Olawuyi, Babatunde James
  • Cantero, B.
  • González-Fonteboa, Belén
[Abstract:] Rapid urbanisation causes a rise in the need for infrastructure, which in turn fuels the creation of additional concrete and further increases cement supplies. Activation of illite-based clay mineral and usage in concrete production is one of the sustainable ways to address the cement industry anthropogenic issues. This study evaluates the durability properties of water transport (water absorption, and capillary water absorption), and resistance to aggressive environments (5% solutions of hydrochloric acid, HCl; sodium sulphate, Na2SO4; and calcium chloride, CaCl2) of meta-illite calcined clay (MCC)-based high-performance concrete (HPC). For this purpose, concrete was produced with 5, 10, 15, 20, 25 and 30% MCC content in partial substitution of CEM II. Results from the water absorption tests indicate an average percentage value of 3.57%, 3.35% and 2.52% for all the observed mixes at 28, 56 and 90 days, respectively, with MCCC-10 HPC having an average best value of 2.23% across the curing ages. On all observed days, the 5 to 15% cement replacements had very close average water sorptivity value of 0.125 ± 0.001 mm/min0.5 with the control mix (0.113 ± 0.011 mm/min0.5). The aggressive environments exposure findings of the hardened MCC-based HPC specimens of 10 to 20% recorded an approximately 15% compressive strength loss in HCl, Na2SO4 and CaCl2 solutions over the 90 days of curing. In all, the HPC mixes of 5 to 15% MCC content obtained an average durability performance factor of 89%. As a result, these findings imply that MCC can replace cement in up to 15% of HPC production., This research was funded by MINECO through two projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020-115433RB-I00” and “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021-121660-I00”. We also thank the Spanish Ministry of Science and Innovation for the financial support through its postdoctoral fellowship to Juan de la Cierva (No FJC2021-047024-I).