Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Role of Eucalyptus Species on the Structural and Thermal Performance of Cellulose Nanocrystals (CNCs) Isolated by Acid Hydrolysis

  • Gil-Castell, Oscar
  • Reyes-Contreras, Pablo
  • Pabla, Pabla Andrea
  • Teixeira Mendonça, Regis
  • Carrillo-Varela, Isabel
  • Badia, José David
  • Serra, Àngels
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Cellulose nanocrystals (CNCs) are attractive materials due to their renewable nature, high surface-to-volume ratio, crystallinity, biodegradability, anisotropic performance, or available hydroxyl groups. However, their source and obtaining pathway determine their subsequent performance. This work evaluates cellulose nanocrystals (CNCs) obtained from four different eucalyptus species by acid hydrolysis, i.e., E. benthamii, E. globulus, E. smithii, and the hybrid En × Eg. During preparation, CNCs incorporated sulphate groups to their structures, which highlighted dissimilar reactivities, as given by the calculated sulphate index (0.21, 0.97, 0.73 and 0.85, respectively). Although the impact of the incorporation of sulphate groups on the crystalline structure was committed, changes in the hydrophilicity and water retention ability or thermal stability were observed. These effects were also corroborated by the apparent activation energy during thermal decomposition obtained through kinetic analysis. Low-sulphated CNCs (E. benthamii) involved hints of a more crystalline structure along with less water retention ability, higher thermal stability, and greater average apparent activation energy (233 kJ·mol¿1) during decomposition. Conversely, the high-sulphated species (E. globulus) involved higher reactivity during preparation that endorsed a little greater water retention ability and lower thermal stability, with subsequently less average apparent activation energy (185 kJ·mol¿1). The E. smithii (212 kJ·mol¿1) and En × Eg (196 kJ·mol¿1) showed an intermediate behavior according to their sulphate index., Financial support was provided by the Innovation Found for Competitiveness of the Chilean Economic Development Agency (CORFO) under Grant no. 13CEI2-21839. Generalitat Valenciana is thanked for the post-doctoral contract for O. Gil-Castell (APOSTD/2020/155). I. Carrillo-Varela thanks ANID/Fondecyt-Postdoctoral grant (No. 3200114). R. Teixeira Mendonça thanks ANID/Fondecyt grant (No. 1200504).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of substrate and temperature on the biodegradation of polyester-based materials: Polylactide and poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) as model cases

  • Gil-Castell, O.
  • Andres-Puche, R.
  • Dominguez, E.
  • Verdejo, E.
  • Monreal Mengual, Llucía|||0000-0001-5355-7564
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The extended use of polymers from renewable resources such as aliphatic polyesters or polyhydroxyalkanoates boosted the necessity to understand their behaviour in an end-of-life scenario. Although they can be degraded in reasonable shorter times than traditional polymers, understanding the degradation mechanisms under dissimilar conditions will contribute to further developments in this field. This work aimed to study the effect of temperature and substrate in the degradation of polylactide (PLA) and poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) in a simulated laboratory scale to ascertain their contribution, separately or in combination. For this purpose, nine parallel degradation assays were performed by means of the combination of mesophilic (25 °C), thermophilic (58 °C) and hyperthermophilic (80 °C) temperatures with enriched synthetic medium, compost and standardised soil substrates. Although the analysis of the surface morphology, the thermal properties and the thermo-oxidative stability revealed changes as a function of time, the evaluation of the molar mass allowed for a more precise determination of the degradation. In general, chain scission was perceived in all cases as a function of time. The effect of temperature was critical, significantly more important than the effect of the substrate, which showed a less significant contribution, especially in terms of molar mass reduction. While for the PLA, biodegradation at 58 °C and thermal degradation at 80 °C resulted in similar consequences, for the PHBH the hyperthermophilic temperature of 80 °C was the most severe condition, regardless of the substrate. From a technological perspective, it may be highlighted that biodegradation at 58 °C may be the most cost-effective condition due to the lower energy supply required and the valuable contribution of the microorganisms., The authors would like to thank the support of the Spanish Ministry of Science, Innovation and Universities, for the POLYDECARBOCELL project (ENE2017-86711-C3-1-R) and the Chilean Economic Development Agency (CORFO) for the project 13CEI2-21839.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of graphene nanoplatelets on the dielectric permittivity and segmental motions of electrospun poly(ethylene-co-vinyl alcohol) nanofibers

  • Badia, J. D.
  • Echegoyen, Y.
  • Lagarón, J. M.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The influence of the addition of graphene nanoplatelets (GNPs) on the intra/inter ¿ molecular segmental motions of poly(ethylene-co-vinyl alcohol) (EVOH) was assessed by means of dielectric thermal analysis (DETA). The relaxation spectra were studied in terms of the dielectric permittivity (¿¿) and the dielectric loss tangent (tan ¿) at wide ranges of frequency (from 10¿2 to 107 Hz) and temperature (from -150 to 140 °C). Two relaxation zones were disthinguished. Below the glass transition temperature (Tg), two ß-relaxations were observed, which are characteristic local modes of mobility of the EVOH side groups, and related to the influence of the different surroundings of ethylene or vinyl alcohol units. At higher temperatures, the dielectric ¿-relaxation in the vicinities of the glass transition of EVOH was determined. The thermal activation of the ß-relaxations was explained by an Arrhenius model, and showed activation energies (Ea) around 55 and 80 kJ·mol¿1. The ¿-relaxation was explained by the Vogel-Fulcher-Tammann-Hesse (VFTH) model. The study of the segmental dynamics showed an increase in the dynamic fragility parameters with the addition of GNPs. The permittivity was increased at preferential concentrations of GNPs. In particular, the addition of GNPs up to 0.5 wt% increased the dielectric permittivity of the electrospun EVOH/GNPs nanocomposite fibers, specially at low frequencies., The authors would like to thank the European Regional Development Funds (ERDF) and the Spanish Ministry of Science, Innovation, and Universities (MICIU) for the concession of the Research Projects ENE2017-86711-C3-1-R and RTI2018-097249-B-C21. The UPV authors would also like to thank the Chilean Economic Development Agency (CORFO) the economic support in the frame of the project 13CEI2-21839. This research was also funded by the EU H2020 YPACK (773872) and USABLE (BBI-JTI-2018-836884) projects. Torres-Giner is a recipient of a Juan de la Cierva-Incorporación contract (IJCI-2016-29675) from MICIU. Universitat Politècnica de València is acknowledged for the post-doctoral aid for R. Teruel-Juanes, under the PAID-10-19 SUB.1 SP20190049 scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Valorization of cotton residues for production of bio-oil and engineered biochar

  • Primaz, Carmem T.
  • Jacques, Rosangela A.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Cotton seed was submitted to fast pyrolysis in a fixed bed reactor and the liquid and solid products were characterized applying several techniques. The detailed chemical composition of the bio-oil was investigated using GC × GC/TOFMS combined with software tools and retention index. A total of 257 compounds were tentatively identified with 168 were confirmed by LTPRI. The most abundant compounds identified in the cotton seed bio-oil were nitrogenous (56 compounds) and phenolic (42 compounds) what distinguishes this bio oil from others, produced from various sources of biomass. The higher heating values of cotton seed and bio-oil were 19.34 MJ kg ¿1 and 34.25 MJ kg ¿1 respectively and demonstrating the feasibility of the use of cotton seed in its natural form for energy generation or as a secondary source once a bio-oil with these characteristics would be a suitable candidate for use in boilers for heating purposes or chemical extraction. The biochar had a significant carbon content and a high heating value (22.12 MJ kg ¿1), making it attractive for fuel applications. The activation methods used were able to improve the physical and chemical characteristics of the biochar, as demonstrated by methylene blue adsorption tests. The maximum adsorption capacity of NaOH-activated biochar was 23.82 mg g ¿1 while that of K2CO3-activated biochar was 332.40 mg g ¿1., The authors would like to thanks the support of Brazilian Coordenaçao de Aperfeicoamento de Pessoal de Nivel Superior(CAPES, scholarships for the first author-Finance code 001) and EBW thorn Project Euro-Brazilian Windows Erasmus Mundus Program (scholarships for the first author).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structure-Properties Relationship of Reprocessed Bionanocomposites of Plasticized Polylactide Reinforced with Nanofibrillated Cellulose

  • Gil-Castell, O.
  • Cea, J.
  • Carrasco, J. C.
  • Giaccinti Baschetti, M.
  • Wolf, Mark Henning|||0000-0003-3033-6616
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Bionanocomposites of polylactide (PLA), plasticized with poly(ethylene glycol) (PEG) (7.5 wt%, 400 and 1500 g/mol) and reinforced with nanofibrillated cellulose (NFC) (1, 3, and 5 wt%) were sequentially compounded, and injection and compression molded. All of the stages caused structural and morphological consequences, more relevant in the plasticized PLA, especially with low molar PEG. Small percentages of NFC (1 and 3 wt%) acted as crystalline nucleating agents and improved thermo-oxidative stability. Given the substantial degradation caused by (re)processing, a downgrading validation strategy was applied, assessing the mechanical and water contact performance during fictional first and second service life applications. After the first processing, PEG increased the ductility and reduced the strength and elastic modulus, while NFC buffered the fall in stiffness and increased rigidity compared to their PLA-PEG counterparts. Once reprocessed, PEG increased the water affinity of the blend, especially for low molar mass PEG. Low percentages of NFC (1 and 3 wt%) modulated water diffusivity and permeability, regardless of the water temperature. Overall, although reprocessing caused significant degradation, the mechanical valorization possibilities of these green bionanocomposites were proven, and are pointed out as sustainable candidates for food packaging or agricultural applications where modulated mechanical or water contact behaviors are required., This research was funded by Generalitat Valenciana (Conselleria d'Innovació, Universitats, Ciència i Societat Digital), as a part of the DEFIANCE research project CIPROM/2021/039 through the PROMETEO funding program, and as a part of the Post-Doctoral Research Program grant number APOSTD/2020/155, and by the Innovation Fund for Competitiveness of the Chilean Economic Development Agency (CORFO), project 13CEI2-21839.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Brewer&apos, s spent grains as biofuels in combustion-based energy recovery processes: Evaluation of thermo-oxidative decomposition

  • Gil-Castell, O.
  • Mascia, N.
  • Primaz, C.
  • Vásqez-Garay, F.
  • Baschetti, M. G.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The high global generation of wastes and side streams from agri-food production has led to environmental impact and causes nature degradation due to their uncontrolled management. These wastes are profitable materials with significant economic value that could otherwise be exploited as new sources in the feed industry or the production of bioenergy. Among them, brewer¿s spent grain (BSG) is a solid by-product generated in the beerbrewing process that consists of the barley grain husks together with parts of the pericarp and seed coat layer. Although it is rich in fibres and proteins, its main use is currently limited to animal feed or simply deposition to landfills. This study pursues the evaluation of BSGs as biofuels in energy recovery processes. For this purpose, the elemental composition, the higher heating value, the content of volatiles, fixed carbon, moisture, and ash yield along with the kinetic analysis of its decomposition during thermo-oxidative combustion were assessed. The thermo-oxidative decomposition of hemicellulose, cellulose, lignin, and char occurred in two main stages. The average apparent activation energy for Stage I was 190¿200 kJ¿mol¿ 1, significantly higher than that of Stage II (100¿150 kJ¿mol¿ 1). Stage I revealed a random nucleation kinetic model (Fn) and involved the volatilisation of hemicellulose and cellulose and partially lignin. Stage II, described by a three-dimensional diffusion kinetic model (D4), comprised the completion of lignin and the decomposition of char. The environmental advantage of using such residues was demonstrated with the low ash yield (in the range of 1.7¿5.4%) and high calorific value between 17.8 and 19.1 MJ¿kg¿ 1. The obtained results serve as the baseline for describing the energy recovery process in a reactor that uses BSG residues as feedstock under oxidative conditions. Altogether it is pointed out the feasibility of using pelletised BSGs regardless of the malt type or mixture as a renewable source of energy in incineration plants above 500 ¿C., The authors would like to thank the support of Generalitat Valenciana for the APOSTD/2020/155 grant for O. Gil-Castell. The Chilean Economic Development Agency (CORFO) is acknowledged for the financial support through project 13CEI2-21839 for the contract for C.T. Primaz. The European Commission is thanked for the project LIFE-LIBERNITRATE (LIFE16 ENV/ES/000419).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of plasticization and reprocessing effects on the segmental cooperativity of polylactide by dielectric thermal spectroscopy

  • B. Pascual-Jose|||0000-0001-7562-916X
  • Ribes-Greus, A.|||0000-0003-2460-8291
  • Badia, J.D.
  • Múgica, A.
  • Addiego, Frédéric
  • Müller, Alejandro J.
[EN] In the present study, the dielectric properties of both neat and plasticized polylactide submitted to repeated extrusion and injection processes to simulate recycling were analysed. The dielectric relaxation spectrum, consisting of 13 and ? relaxation, revealed the relevance of both acryl-PEG based plasticization and thermomechanical degradation induced by repeated extrusion and grinding-injection reprocessing cycles on polylactide (PLA). The 13-relaxation has its origin in the intramolecular local motions of pendant groups of the PLA backbone, while the ?-relaxation is representative of the intermolecular large-scale segmental motions of the PLA backbone. The addition of acryl-PEG to PLA (pPLA) induced an increment in the apparent activation energies and temperatures of the 13-relaxation due to the different nature of the acryl-pendant group in pPLA. Moreover, the crystallization rate of pPLA was much faster compared to that of neat PLA, which hindered the movements of the acryl-pendant group, thus requiring more energy to orient the dipoles. The plasticizing effect of acryl-PEG effectively aids the large-scale motions associated to the glass transition, which are the origin of the ?-relaxation. The effect of reprocessing in PLA is less relevant than the addition of the acryl-PEG plasticizer, in terms of dielectric behaviour. With increasing the number of processing cycles, the crystallization rate of PLA gradually increased, but the permittivity was still much lower than that of pPLA, for which crystallinity remained constant. Nonetheless, for the case of the ?-relaxation of pPLA, the rearrangements produced by chain scission induced an enhancement of the thermal activation of the orientation of the dipoles but reduced the dynamic fragility and increased the embrittlement of pPLA after reprocessing. These differences found in the relaxation spectrum and the molecular dynamics in the environment of the glass transition for PLA and pPLA, together with the embrittlement of pPLA after reprocessing, is what will determine the final use of one or the other recycled polymer., The authors would like to thank the support of the European Union through the European Regional Development Funds (ERDF) and the Spanish Ministry of Economy, Industry and Competitiveness, for the research project POLYDECARBOCELL (ENE201786711C31R) . The authors would also like to thank the economic support of the Chilean Economic Development Agency (CORFO) in the frame of the project 13CEI221839. The UPV/EHU team acknowledges funding from the Basque Government through grant IT130919.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Encapsulation of Vitamins A and E as Spray-Dried Additives for the Feed Industry

  • Mújica-Álvarez, Javiera
  • Gil-Castell, O.
  • Barra, Pabla A.
  • Bustos, Rubén
  • Faccini, Mirko
  • Matiacevich, Silvia
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Encapsulated fat-soluble powders containing vitamin A (VA) and E (VE) were prepared as a feasible additive for extruded feed products. The e ect of the encapsulating agents (Capsul-CAP®, sodium caseinate-SC) in combination with Tween 80 (TW) as an emulsifier and maltodextrin (MD) as a wall material on the physicochemical properties of emulsions and powders was evaluated. First, nanoemulsions containing MD:CAP:TW:VA/VE and MD:SC:TW:VA/VE were prepared and characterized. Then, powders were obtained by means of spray-drying and analyzed in terms of the product yield, encapsulation e ciency, moisture content, porosity, surface morphology, chemical structure, and thermal properties and thermo-oxidative/thermal stability. Results showed that although nanoemulsions were obtained for all the compositions, homogeneous microcapsules were found after the drying process. High product yield and encapsulation e ciency were obtained, and the presence of the vitamins was corroborated. The characteristics of the powders were mainly influenced by the encapsulating agent used and also by the type of vitamin. In general, the microcapsules remained thermally stable up to 170 C and, therefore, the proposed encapsulation systems for vitamins A and E were suitable for the preparation of additives for the feed manufacturing through the extrusion process., This research was funded by the Innovation Found for Competitiveness of the Chilean Economic Development Agency (CORFO), grant number 13CEI2-21839, and the University of Santiago de Chile (USACH) [USA1799_MS172228; 081971M].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Strategies towards thermochemical valorisation of spent coffee grounds (SCG): Kinetic analysis of the thermal and thermo-oxidative decomposition

  • Primaz, C.
  • Gil-Castell, O.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The thermochemical conversion of spent coffee grounds (SCG) under inert and oxidative atmospheres was comprehensively assessed as a feasible valorisation route for this biomass. Dynamic thermogravimetric analyses were performed at different heating rates. The individual contributions of the pseudo-components (hemicellulose, cellulose, and lignin) were determined by deconvolution using Lorentzian functions. For each pseudo-component, the kinetic triplet—apparent activation energy (Ea), pre-exponential factor (A), and reaction model (g(α))—was established by combining isoconversional methods, master-curve analysis, and the Pérez-Maqueda criterion. Under inert conditions, distinct mass-loss steps were identified corresponding to moisture release, decomposition of hemicellulose and cellulose and partial lignin degradation, followed by completion of lignin decomposition, leaving ~20% biochar. The Ea values were 217 kJ·mol⁻¹ (hemicellulose), 214 kJ·mol⁻¹ (cellulose), and 151 kJ·mol⁻¹ (lignin). Under oxidative conditions, similar stages were observed; however, the biochar was further oxidised, yielding only ash as residue (~2%). These results support the use of SCG as a solid biofuel, given its high LHV and HHV (≈20 MJ·kg⁻¹). The Ea values under oxidative conditions were 194 kJ·mol⁻¹ (hemicellulose), 147 kJ·mol⁻¹ (cellulose), and 173 kJ·mol⁻¹ (lignin). Similar decomposition behaviours were obtained regardless of atmosphere for hemicellulose (F4), cellulose (D3), and lignin (F2/4), suggesting that temperature, reactant concentration, particle morphology, and product diffusion govern SCG decomposition during non-isothermal pyrolytic and combustive thermochemical processes., The authors would like to thank the Chilean Economic Development Agency (CORFO) for the financial support through project 13CEI2-21839 and the contract for C.T. Primaz. Generalitat Valenciana is also acknowledged for the APOSTD/2020/155 grant for O. Gil-Castell.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Spray-Drying Performance and Thermal Stability of L-ascorbic Acid Microencapsulated with Sodium Alginate and Gum Arabic

  • Barra, Pabla A.
  • Márquez, Katherine
  • Gil-Castell, O.
  • Mújica, Javiera
  • Faccini, Mirko
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The potential of sodium alginate (ALG) and gum arabic (GA) as wall polymers for Lascorbic acid (AA) encapsulation as a tool for their preservation against the thermo-oxidative degradation was investigated. The influence of such polymers used as wall material on the AAcontent, size, encapsulation efficiency, encapsulation yield and thermo-oxidative stability were evaluated. The AA-microparticles were obtained using the spray-drying technique. An experimental Taguchi design was employed to assess the influence of the variables in the encapsulation process. The microparticles morphology and size distribution were characterized by scanning electron microscopy and laser diffraction. The thermal stability of AA microparticles was studied by differential scanning calorimetry and thermogravimetry analysis. This work points out the viability to encapsulate AA using GA and ALG through a spray-drying process. In general, a product yield ranging from 35.1% to 83.2% and an encapsulation efficiency above 90% were reached. Spherical microparticles with a smooth surface were obtained with a mean diameter around 6 ¿m and 9 ¿m for the those prepared with GA and ALG, respectively. The thermo-oxidative analysis showed that both polymers allow maintaining AA stable up to 188 °C, which is higher than the traditional processing temperature used in the fish feed industry., Financial support was provided by the Innovation Found for Competitiveness of the Chilean Economic Development Agency (CORFO) through the project 13CEI2-21839.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Degradation of Plasticised Poly(lactide) Composites with Nanofibrillated Cellulose in Different Hydrothermal Environments

  • Wolf, Mark Henning|||0000-0003-3033-6616
  • Ribes-Greus, A.|||0000-0003-2460-8291
  • Gil-Castell, Óscar
  • Cea, J.
  • Carrasco, J. C.
[EN] In this study, bionanocomposite films based on poly(lactide) (PLA) plasticised with poly(ethylene glycol) (PEG) (7.5 wt%) and reinforced with various contents of nanofibrillated cellulose (NFC) (1, 3, 5 wt%) were prepared. The hydrothermal degradation was investigated through immersion in several aqueous environments at temperatures of 8, 23, 58, and 70 °C as a function of time (7, 15, 30, 60, 90 days). The effect of water immersion on the physicochemical properties of the materials was assessed by monitoring the changes in the morphology, thermo-oxidative stability, thermal properties, and molar mass through field emission scanning electron microscopy (FE-SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and gel permeation chromatography (GPC). The hydrothermal degradation behaviour was not critically affected regardless of the nanofibrillated cellulose content. All the materials revealed certain integrity towards water immersion and hydrolysis effects at low temperatures (8 and 23 °C). The low hydrothermal degradation may be an advantage for using these PLA biocomposites in contact with water at ambient temperatures and limited exposure times. On the other hand, immersion in water at higher temperatures above the glass transition (58 and 70 °C), leads to a drastic deterioration of the properties of these PLA-based materials, in particular to the reduction of the molar mass and the disintegration into small pieces. This hydrothermal degradation behaviour can be considered a feasible option for the waste management of PLA/PEG/NFC bionanocomposites by deposition in hot aqueous environments., This research was funded by Generalitat Valenciana (Conselleria d'Innovacio, Universitats, Ciencia i Societat Digital), as a part of the DEFIANCE research project CIPROM/2021/039 through the PRO-METEO funding program. Generalitat Valenciana is also thanked for the post-doctoral contract of O. Gil-Castell (APOSTD/2020/155). The Innovation Fund for Competitiveness of the Chilean Economic Development Agency (CORFO) is acknowledged for the financial support through the project 13CEI2-21839. Funding for open access charge is recognised to CRUE-Universitat Politecnica de Valencia-thanks to the CRUE-CSIC agreement with Springer Nature.