Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A quantitative criterion for determining the order of magnetic phase transitions using the magnetocaloric effect

  • Law, Jia Yan
  • Franco, V.
  • Moreno-Ramírez, Luis M.
  • Conde Amiano, Alejandro
  • Karpenkov, Dmitriy
  • Radulov, IIiya
  • Skokov, Konstantin P.
  • Gutfleisch, O.
The ideal magnetocaloric material would lay at the borderline of a first-order and a secondorder phase transition. Hence, it is crucial to unambiguously determine the order of phase transitions for both applied magnetocaloric research as well as the characterization of other phase change materials. Although Ehrenfest provided a conceptually simple definition of the order of a phase transition, the known techniques for its determination based on magnetic measurements either provide erroneous results for specific cases or require extensive data analysis that depends on subjective appreciations of qualitative features of the data. Here we report a quantitative fingerprint of first-order thermomagnetic phase transitions: the exponent n from field dependence of magnetic entropy change presents a maximum of n > 2 only for first-order thermomagnetic phase transitions. This model-independent parameter allows evaluating the order of phase transition without any subjective interpretations, as we show for different types of materials and for the Bean–Rodbell model., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gd+GdZn biphasic magnetic composites synthesized in a single preparation step: Increasing refrigerant capacity without decreasing magnetic entropy change

  • Law, Jia Yan
  • Moreno-Ramírez, Luis M.
  • Blázquez, J. S.
  • Franco, V.
  • Conde Amiano, Alejandro
Biphasic Gd + GdZn composites (GdZn; x = 0, 5, 15 and 25 at.%) were successfully obtained in a single fabrication step by induction melting. X-ray microdiffraction results reveal the homogeneity of all the prepared samples and indicate a combination of GdZn and Gd phases with different proportions. With this method, the main drawbacks of preparing composites have been avoided, providing the additional advantage of enhanced thermal conductivity between phases. The biphasic Gd + GdZn composite shows an enhanced refrigerant capacity in comparison to Gd (11%) as well as to single phase GdZn (45%). Heat capacity measurements provide an adiabatic temperature change of around 3.5 K for 20 kOe for the optimal composite., This work was supported by Spanish MINECO and EU-FEDER (Project MAT2013-45165-P) as well as the PAI of the Regional Government of Andalucía. L.M. Moreno-Ramírez acknowledges a FPU fellowship from Spanish MECD., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanocrystallization kinetics understood as multiple microprocesses following the classical theory of crystallization

  • Manchón-Gordón, Alejandro F.
  • Blázquez, J. S.
  • Conde, Clara F.
  • Conde Amiano, Alejandro
In this work, we propose a model for using the classical Johnson-Mehl-Avrami-Kolmogorov (JMAK) crystallization theory to analyze nanocrystallization processes as a set of multiple microprocesses. This model is based on the well-known microstructure observations of nanocrystalline systems for which, although the number of crystallites increases along the process, the growth of each crystallite is limited to a much shorter time than the needed one for completing the process. The very low values of the Avrami exponent, n∼1, are well reproduced assuming a set of multiple classical JMAK processes with constant nucleation rate and diffusion controlled growth, n = 2.5 for each i individual microprocess. It is shown that the values of Avrami exponent experimentally observed and lying out of the theoretical range can be assumed as effective values derived from a complex process consisting of multiple microprocesses, which can be individually treated as classical ones., This work was supported by MINECO and EU FEDER (project MAT2013-45165-P), and the PAI of the Regional Government of Andalucía. A.F. Manchón-Gordón acknowledges a research internship funded by the Spanish Ministry of Education.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetocaloric response of amorphous and nanocrystalline Cr-containing Vitroperm-type alloys

  • Moreno-Ramírez, Luis M.
  • Blázquez, J. S.
  • Franco, V.
  • Conde Amiano, Alejandro
  • Marsilius, M.
  • Budinsky, V.
  • Herzer, G.
The broad compositional range in which transition metal (TM) based amorphous alloys can be obtained, yields an easily tunable magnetocaloric effect (MCE) in a wide temperature range. In some TM-based alloys, anomalous behaviors are reported, as a non-monotonous trend with magnetic moment (e.g. FeZrB alloys). Moreover, in certain Cr-containing Vitroperm alloys anomalously high values of the magnetic entropy change were published. In this work, a systematic study on MCE response of Cr-containing amorphous alloys of composition FeCrCuNbSiB (with x=2, 8, 10, 12, 13, 14 and 20) has been performed in a broad Curie temperature range from 100 K to 550 K. Curie temperature and magnetic entropy change peak of the amorphous alloys decrease with the increase of Cr content at rates of-25.6 K/at% Cr and-54 mJ kg K/at% Cr, respectively, following a linear trend with the magnetic moment in both cases. The presence of nanocrystalline phases has been considered as a possible cause in order to explain the anomalies. The samples were nanocrystallized in different stages, however, the magnetocaloric response decreases as crystallization progresses due to the large separation of the Curie temperatures of the two phases., This work was supported by the Spanish MINECO (Project MAT2013-45165-P) and the PAI of the Regional Government of Andalucía. L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimal temperature range for determining magnetocaloric magnitudes from heat capacity

  • Moreno-Ramírez, Luis M.
  • Blázquez, J. S.
  • Law, Jia Yan
  • Franco, V.
  • Conde Amiano, Alejandro
The determination of the magnetocaloric magnitudes (specific magnetic entropy change, Δs , and adiabatic temperature change, ΔT ) from heat capacity (c ) measurements requires measurements performed at very low temperatures (∼0 K) or data extrapolation when the low temperature range is unavailable. In this work we analyze the influence on the calculated Δs and ΔT of the usually employed linear extrapolation of c from the initial measured temperature down to 0 K. Numerical simulations have been performed using the Brillouin equation of state, the Debye model and the Fermi electron statistics to reproduce the magnetic, lattice and electronic subsystems, respectively. It is demonstrated that it is not necessary to reach experimentally temperatures very close to 0 K due to the existence of certain starting temperatures of the experiments, the same for Δs and ΔT , that minimize the error of the results. A procedure is proposed to obtain the experimental magnitudes of Δs and ΔT with a minimum error from c data limited in temperature. It has been successfully applied to a GdZn alloy and results are compared to those derived from magnetization measurements., This work was supported by the Spanish MINECO and EU-FEDER (project MAT2013-45165-P and MAT2016-77265-R) and the PAI of the Regional Government of Andalucía. LM Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the induced anisotropy in field annealed hitperm alloys by mössbauer spectroscopy and kerr microscopy

  • Blázquez, Javier S.
  • Marcin, J.
  • Andrejka, F.
  • Franco, V.
  • Conde Amiano, Alejandro
  • Skorvanek, I.
Samples of FeCoNbBCu alloy were nanocrystallized under zero field annealing (ZF) and transverse field annealing (TF) conditions. A reduction in coercivity for TF samples with respect to ZF sample (16 and 45 A/m, respectively) is observed. Kerr microscopy images show a well-defined parallel domain structure, transversally oriented to the ribbon axis for the TF sample unlike for the ZF sample, for which a complex pattern is observed with large and small domains at the surface of the ribbon. Although Mössbauer spectra are clearly different for the two studied samples, Mössbauer studies confirm that there is no significant difference between the hyperfine field distributions of TF and ZF samples but only the relative intensity of the 2nd and 3rd lines A (related to the angle between the gamma radiation and the magnetic moments, α). However, for TF annealed samples α = 90 deg (A = 4), indicating that the magnetic moments lay on the plane of the ribbon in agreement with the well-defined domain structure observed by Kerr microscopy, ZF annealed samples show A = 1.8. This value is close to that of a random orientation (A = 2) but smaller, indicating a slight preference for out of plane orientations. Moreover, it is clearly smaller than that of the as-cast amorphous samples A = 2.8, with a preference to in-plane orientations. The application of the law of approach to saturation yields a larger effect of the inhomogeneities in ZF sample with respect to TF one., This work was supported by the Spanish Ministry of Science and Innovation and EU FEDER (Project MAT2013-45165-P), the PAI of the Regional Government of Andalucía, and the Slovak Projects APVV-0492-11, VEGA 2/0192/13. The Slovak team acknowledges also the support of the Operational Program “Research and Development” financed through European Regional Development Fund through the Projects ITMS 26220120019 and ITMS 26220220061.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Grinding and particle size selection as a procedure to enhance the magnetocaloric response of La(Fe,Si)13 bulk samples

  • Ipus, Jhon J.
  • Borrego, J.M.
  • Moreno-Ramírez, Luis M.
  • Blázquez, J. S.
  • Franco, V.
  • Conde Amiano, Alejandro
The magnetocaloric effect of La(Fe,Si) samples deteriorates with the presence of secondary phases. However, it is highly challenging to produce single phase samples by conventional procedures and purification requires long annealing time. We propose grinding and particle size selection of non-optimal starting samples as procedure to enhance the magnetocaloric response. In this study a starting multiphase LaFeSi ingot was grinded and sieved to select three different particle size ranges. X-ray diffraction and Mössbauer spectrometry reveal that all samples mainly contain fcc-La(Fe,Si) and bcc-Fe(Si) phases. Microstructural and magnetic results show that the fcc-La(Fe,Si) phase fraction increases for samples with the smallest average particle size, increasing their magnetocaloric response in a factor larger than three with respect to that of the bulk sample., This work was supported by the Spanish MINECO and EU FEDER (projects MAT2013-45165-P and MAT2016-77265-R) and the PAI of the Regional Government of Andalucía. L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of phases evolution in high-coercive MnAl powders obtained through short milling time of gas-atomized particles

  • Law, Jia Yan
  • Rial, J.
  • Villanueva, M.
  • López, N.
  • Camarero, J.
  • Marshall, L. G.
  • Blázquez, Javier S.
  • Borrego, J.M.
  • Franco, V.
  • Conde Amiano, Alejandro
  • Lewis, L. H.
  • Bollero, A.
Gas-atomized MnAl particles constituted nominally of only ε- and γ-phases, i.e. no content of the ferromagnetic L1-type τ-phase, have been used to study the evolution of phases during short time of high-energy milling and subsequent annealing. Milling for 3 min is sufficient to begin formation of the τ-MnAl phase. A large coercivity of 4.9 kOe has been obtained in milled powder after annealing at 355 °C for 10 min. The large increase in coercivity, by comparison with the lower value of 1.8 kOe obtained for the starting material after the same annealing conditions, is attributed to the combined formation of the τ-MnAl and β-Mn phases and the creation of a very fine microstructure with grain sizes on the order of 20 nm. Correlation between morphology, microstructure and magnetic properties of the rapidly milled MnAl powders constitutes a technological advance to prepare highly coercive MnAl powders., The gas-atomized powders were provided by Prof. Ian Baker, Dartmouth College where they were produced via a grant from the U.S. Department of Energy, Advanced Research Projects Agency – Energy (ARPA-E) through REACT program contract no. DE-AR0000188. This research has been funded by MINECO (Spanish Ministry of Science and Innovation): ENMA-National project (MAT2014-56955-R) and Northeastern University, MINECO through M-era.Net Programme: NEXMAG project (PCIN-2015-126) and Regional Government (Comunidad de Madrid): NANOFRONTMAG (Ref. S2013/MIT-2850), MINECO (project MAT2013-45165-P) and the PAI of the Regional Government of Andalucía. N. López acknowledges MINECO for the “Promoción de Empleo Joven” (PEJ-2014) in the frame of Sistema Nacional de Garantía Juvenil and funding by FSE and IEJ., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tunable magnetocaloric effect around room temperature by Fe doping in Mn0.98Cr(0.02-x)FexAs compound

  • Ipus, Jhon J.
  • Ribeiro, Paula O.
  • Ranke, P. von
  • Caraballo Vivas, R. J.
  • Carvalho, Alexandre M. G.
  • Coelho, Adelino A.
  • Franco, V.
  • Rocco, Daniel L.
In this work, we present an investigation of the magnetic and magnetocaloric properties of MnCrFeAs compounds with x = 0.002, 0.005 and 0.010. Our findings show that as Fe content increases the unit cell volume decreases, which indicates that Fe doping emulates the pressure effect on the crystalline structure. The transition temperature T decreases as x increases and it can be set at approximate value of room temperature by changing the doping level. In addition, the magnetic entropy change ΔS was determined using a discontinuous measurement protocol, and realistic values from the magnetocaloric effect presented by MnAs-type compounds under pressure (emulated pressure) could be obtained. The values of ΔS are very large, around −11 JkgK with ΔH = 15 kOe, which is higher than that observed for most compounds with T around room temperature. However, ΔS is confined to a narrow temperature range of 11 K. To overcome this drawback, the composition of a theoretical composite formed by our samples was calculated in order to obtain a table-shaped ΔS curve. The simulated composite showed a high value of full width at half maximum δT of 33 K, which is much higher than that of single sample., We acknowledge FAPERJ (Grant Nos. E-26/110.393/2014 and E-16/210.263/2014), CAPES, CNPq (Grant No. 485200/2013-9), FAPESP (Grant No. 2012/03480-0), PROPPI-UFF, MINECO and EU FEDER (project MAT2013-45165-P) and the PAI of the Regional Government of Andalucía for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ball milling as a way to produce magnetic and magnetocaloric materials: a review

  • Blázquez, Javier S.
  • Ipus, Jhon J.
  • Moreno-Ramírez, Luis M.
  • Álvarez-Gómez, J.M.
  • Sánchez-Jiménez, D.
  • Lozano-Pérez, S.
  • Franco, V.
  • Conde Amiano, Alejandro
Ball milling (BM) is a well-established technique for producing different materials in powder shape. Dynamical analysis of BM helps to optimize the process through simple but general relations (e.g., definition of an equivalent milling time). Concerning the field of study of magnetocaloric effect (MCE), BM is used in different ways: as a single step process (mechanical alloying), as an initial step to enhance mixing of the elements (e.g., to speed up the formation of the desired intermetallic phase) or as a final step (e.g., hydriding of La–Fe–Si). In this contribution, besides a simple description of the effects of some geometrical parameters on the power released during BM and a short review of the BM contribution to the research field of MCE, we will discuss the effect of the microstructure of the starting material and the granular shape inherent to BM on magnetic materials exhibiting MCE., Spanish MINECO and EU FEDER (Projects MAT 2013-45165-P), AEI/FEDER-UE (Project MAT-2016-77265-R) and the PAI of the Regional Government of Andalucía. L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD. MINECO/ICTI2013-2016/MAT-2016-77265-R
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Predicting the tricritical point composition of a series of LaFeSi magnetocaloric alloys via universal scaling

  • Franco, V.
  • Law, Jia Yan
  • Conde Amiano, Alejandro
  • Brabander, V.
  • Karpenkov, D. Y.
  • Radulov, I.
  • Skokov, K.
  • Gutfleisch, O.
Typically, the most common techniques to determine the order of the phase transition of magnetocaloric materials do not allow a quantitative prediction of the composition that corresponds to the change from first to second order phase transition, i.e. the so-called tricritical point of an alloy series. In this work, we study a series of LaFeSi alloys in which the different Fe/Si ratio produces a change in the order of the transition. We show the quantitative prediction of the tricritical composition analyzing the field dependence of the peak magnetic entropy change. The proposed procedure is also simple to implement, as it does not require any modelling of the experimental data and it only requires temperature and field dependent magnetization experiments. It is shown that the obtained value is in agreement with the results emerging from the most commonly used qualitative techniques., This work was supported by MINECO and EU FEDER (project MAT2013-45165-P), AEI/FEDER-UE (project MAT-2016-77265-R), the PAI of the Regional Government of Andalucía, the Deutscher Akademischer Austauschdienst DAAD (Award A/13/09434). OG, IR, and KS would like to acknowledge funding by the DFG in the framework of the priority program 'Ferroic Cooling' (SPP1599).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructuring as a procedure to control the field dependence of the magnetocaloric effect

  • Doblas, D.
  • Moreno-Ramírez, Luis M.
  • Franco, V.
  • Conde Amiano, Alejandro
  • Svalov, A. V.
  • Kurlyandskaya, G. V.
In this work, the field dependence of the magnetocaloric effect of Gd bulk samples has been enhanced through nanostructuring of the material. Nanostructuring consists in multilayers preparation by alternative rf-sputtering deposition of Gd layers and Ti spacers onto glass substrates. The results obtained for the multilayers were compared to those obtained for the Gd bulk. Assuming a power law for the field dependence of the magnetic entropy change (ΔS ∝ H), higher field dependences close to the transition in a wider temperature range are obtained for the multilayer material (n = 1.0) with respect to the bulk counterpart (n = 0.78). The effect of a Curie temperature distribution in the multilayer material (due to variations of the layer thickness) has been studied through numerical simulations to explain the observed field dependence of the magnetocaloric effect, obtaining a remarkable agreement between experiments and results., This work was supported by the Spanish MINECO and EU-FEDER (projects MAT2013-45165-P and MAT2016-77265-R), the PAI of the Regional Government of Andalucía, and the Ministry of Education and Science of the Russian Federation (Project No. 2582). L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Two different critical regimes enclosed in the Bean-Rodbell model and their implications for the field dependence and universal scaling of the magnetocaloric effect

  • Romero-Muñiz, Carlos
  • Franco, V.
  • Conde Amiano, Alejandro
In the last few years power laws and universal scaling have been extensively used to study the field dependence of the magnitudes involved in the magnetocaloric effect of materials. They are key tools which allow us to compare the performing properties of different materials regardless of their nature, processing or experimental conditions during measurements. It was proved that power laws and universal scaling are a direct consequence of critical phenomena in the neighborhood of phase transitions. However, there remains some controversy about the reliability of these procedures. In this work we use the well-known Bean-Rodbell model to confirm that these features are unmistakably related to the critical behavior of the continuous phase transitions. In this specific model, universal scaling occurs either at a purely mean field second order transition or at a tricritical point. Finally, we analyze in detail if the universal scaling is compatible with materials at the tricitical point, making a comprehensive comparison with available experimental data from the literature. We conclude that it is really difficult to know with full certainty if a sample really is in the tricritical regime., This work was supported by the Spanish MINECO and EU FEDER (Projects MAT2013-45165-P and MAT2016-77265-R) and the PAI of the Regional Government of Andalucía. CRM is grateful to a FPI-UAM graduate scholarship program and Fundación Universia for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Time evolution of mechanical amorphization: a kinetic model

  • Blázquez, Javier S.
  • Ipus, John J.
  • Conde Amiano, Alejandro
A model is proposed to describe the evolution of the amorphization process driven by mechanical grinding. This model considers the interface controlled growth of the disordered regions at the boundaries between the crystallites (unlike the classical nucleation and growth theory, the growing particles are thus concave which affects the kinetic equation). The validity of this model has been tested for the amorphization process of mechanically alloyed Fe-Nb-B system at different frequencies. Predictions of the model are in agreement with the experimental results and values of the linear growth rate and the thickness of the starting disordered layer are obtained., This work was supported by MINECO and EU FEDER (projects MAT2013-45165-P and MAT2016-77265-R) and the PAI of the Regional Government of Andalucía. MINECO/ICTI2013-2016/MAT2016-77265-R
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Correction of the shape effect on magnetic entropy change in ball milled Fe70Zr30 alloys

  • Manchón-Gordón, Alejandro F.
  • Ipus, John J.
  • Moreno-Ramírez, Luis M.
  • Blázquez, Javier S.
  • Conde, Clara F.
  • Franco, V.
  • Conde Amiano, Alejandro
The field dependence of the magnetic entropy change (ΔS) after mechanical alloying of FeZr composition starting from high purity powders is studied. Samples with different shapes and different crystalline fraction X were analyzed. Although the results show that the proposed correction of the demagnetizing field has not a significant effect on ΔS(T) curves (∼5% underestimation), it is necessary in order to properly analyze the field dependence of this magnitude (|ΔS|=aH). This correction allows recovering the theoretically predicted field dependence as well as a deeper analysis on multiphase systems. In fact, the biphasic character of the studied system changes the value of the field exponent n: it decreases below two above Curie temperature (T), and it increases at T. We show that, assuming a non-interacting phase model, it is possible to obtain the value of the exponent n for the main phase from the intercept of n vs X/ΔS., This work was supported by the Spanish MINECO and EU FEDER (Project MAT-2013-45165-P), AEI/FEDER-UE (Project MAT-2016-77265-R) and the PAI of the Regional Government of Andalucía. A.F. Manchón-Gordón acknowledges a VPPI-US fellowship from the University of Sevilla. L.M Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD. MINECO/ICTI2013-2016/MAT-2016-77265-R
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the starting temperature of calorimetric measurements on the accuracy of determined magnetocaloric effect

  • Moreno-Ramírez, Luis M.
  • Franco, V.
  • Conde Amiano, Alejandro
  • Neves Bez, H.
  • Mudryk, Y.
  • Pecharsky, Vitalij K.
Availability of a restricted heat capacity data range has a clear influence on the accuracy of calculated magnetocaloric effect, as confirmed by both numerical simulations and experimental measurements. Simulations using the Bean-Rodbell model show that, in general, the approximated magnetocaloric effect curves calculated using a linear extrapolation of the data starting from a selected temperature point down to zero kelvin deviate in a non-monotonic way from those correctly calculated by fully integrating the data from near zero temperatures. However, we discovered that a particular temperature range exists where the approximated magnetocaloric calculation provides the same result as the fully integrated one. These specific truncated intervals exist for both first and second order phase transitions and are the same for the adiabatic temperature change and magnetic entropy change curves. The effect of this truncated integration in real samples was confirmed using heat capacity data of Gd metal and GdSiGe compound measured from near zero temperatures., Work in Sevilla supported by the Spanish MINECO (project MAT2013-45165-P), AEI/FEDER-UE (project MAT-2016-77265-R) and the PAI of the Regional Government of Andalucía – Spain. L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD. Work in Ames supported by the U.S. Department of Energy (DOE) Advanced Manufacturing Office of the Office of Energy Efficiency and Renewable Energy (CaloriCool®). Ames Laboratory is supported by the U.S. DOE Office of Science and operated by Iowa State University under Contract No. DE-AC02-07CH11358., Peer reviewed, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evolution of Fe environments and phase composition during mechanical amorphization of Fe70Zr30 and Fe70Nb30 alloys

  • Manchón-Gordón, Alejandro F.
  • Ipus, J.J.
  • Blázquez, J. S.
  • Conde, Clara F.
  • Conde Amiano, Alejandro
Amorphous Fe-Zr and Fe-Nb alloys with 70 at.% Fe have been prepared by ball milling a mixture of elemental powders. The combination of Mössbauer spectroscopy, X-ray diffraction, scanning electron microscopy and differential scanning calorimetry techniques supplies detailed information about the composition as well as microstructural parameters of remaining crystalline and amorphous phases developed during milling. Detailed analysis of the Fe environments allows us to distinguish Fe atoms in paramagnetic sites between those incorporated to crystalline Zr or Nb rich phases and those Fe atoms in amorphous phase., This work was supported by the Spanish MINECO and EU FEDER (Project MAT 2013-45165-P), AEI/FEDER-UE (Project MAT-2016-77265-R) and the PAI of the Regional Government of Andalucía. A.F. Manchón-Gordón acknowledges a VPPI-US fellowship from University of Sevilla., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetocaloric effect: From materials research to refrigeration devices

  • Franco, V.
  • Blázquez, J. S.
  • Ipus, Jhon J.
  • Law, Jia Yan
  • Moreno-Ramírez, Luis M.
  • Conde Amiano, Alejandro
The magnetocaloric effect and its most straightforward application, magnetic refrigeration, are topics of current interest due to the potential improvement of energy efficiency of cooling and temperature control systems, in combination with other environmental benefits associated to a technology that does not rely on the compression/expansion of harmful gases. This review presents the fundamentals of the effect, the techniques for its measurement with consideration of possible artifacts found in the characterization of the samples, a comprehensive and comparative analysis of different magnetocaloric materials, as well as possible routes to improve their performance. An overview of the different magnetocaloric prototypes found in literature as well as alternative applications of the magnetocaloric effect for fundamental studies of phase transitions are also included., This work was supported by the Spanish MINECO (project MAT2013-45165-P), AEI/FEDER-UE (project MAT-2016-77265-R) and the PAI of the Regional Government of Andalucía. L.M. Moreno-Ramírez acknowledges a FPU fellowship from the Spanish MECD.