Pasar al contenido principal

MODELADO Y VALIDACION DEL PLAQUEADO POR LASER Y SOLDADURA POR CONDUCCION

MAT2008-06882-C04-03

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2008
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDADE DA CORUÑA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Titanium Metal Matrix Composite Laser Coatings Based on Carbides

  • Amigó, Vicente|||0000-0002-2107-0273
  • Candel Bou, Juan José
  • Franconetti Rodríguez, Patricia
Laser cladding is an adequate technique to fabricate Metal Matrix Composite (MMC) layers because of its focused high energy which allows the partial melting of hard ceramic reinforces particles like carbides. Thus, the wettability and gradual transition between metal and particle can be improved. However, metastable or new intermetallic phases can be formed during laser processing due to severe thermal cycle imposed to the clad with unknown properties in some cases. In this work our experience on microstructural analysis of Ti-MMC coatings acquired during the last five years is summarized. Special attention is paid on carbide dilution and secondary carbides formation mechanisms when TiC, SiC, Cr3C2, WC and B4C are mixed with titanium alloys., This work is financially supported by Spanish Ministry of Science (Grant No. MAT2008-06882- C04-03/04 and BES-2009-013589) under the National Industrial Production Programme.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluación de la oxidación superficial de recubrimientos de Ti6Al4V obtenidos por recubrimiento por láser, Evaluation of superficial oxidation layer of Ti6Al4V laser cladding coatings

  • Amigó, Vicente|||0000-0002-2107-0273
  • Candel Bou, Juan José
  • Amado, J.M.
  • Yañez, A.
[ES] Se ha estudiado la in¿uencia de los parámetros de procesado sobre la oxidación super¿cial y propiedades mecánicas de diferentes recubrimientos de Ti6Al4V. La gran reactividad química del polvo de titanio junto a la elevada temperatura que se alcanza producen gran variedad de colores en los óxidos formados. Esta oxidación puede tener un efecto perjudicial sobre el comportamiento en servicio, por lo que su evaluación es fundamental. Aunque la in¿uencia del procesado en el color de los óxidos formados es clara, no existe una relación sencilla que explique sus propiedades mecánicas. Por ese motivo se ha seguido una metodología basada en la microscopia, microanálisis por espectroscopia de longitud de onda (WDS) y nanoindentación. Los resultados indican que no hay diferencias importantes en la dureza y módulo elástico entre dos recubrimientos que presentan diferentes colores de oxidación, [EN] It has been studied the in¿uence of processing parameters on the super¿cial oxidation and mechanical properties of different coatings of Ti6Al4V. The high chemical reactivity of titanium powder, and the high temperature reached during laser processing, produces a great variety of colors in the oxides formed. This oxidation can have a detrimental effect on the behavior in service so that its evaluation is essential. Although the in¿uence of processing on the color of the oxides formed is clear, there is no simple relationship to explain its mechanical properties. For this reason it has been applied a methodology based on microscopy, microanalysis wavelength spectroscopy (WDS) and nanoindentation. The results indicate no signi¿cant differences in hardness and elastic modulus between two coatings with different colors of oxidation., Los autores agradecen al Ministerio de Ciencia e Innovación por la financiación de esta investigación a través de los proyectos MAT2008-06882-C04-03/04 enmarcados en el Programa de Materiales del Plan Nacional.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modeling of phase transformations of Ti6Al4V during laser metal deposition

  • Suárez, A.
  • Tobar, M. J.
  • Yañez, A.
  • Pérez, I
  • Sampedro, Jesús
  • Candel Bou, Juan José
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The low density, excellent high temperature mechanical properties and good corrosion resistance of titanium and its alloys have led to a diversified range of successful applications. As a consequence, there is a demand of increasing the capabilities of processing such alloys. The laser cladding technique allows direct metal deposition with an excellent metallurgical bond and a pore free fine grained microstructure. A nonlinear transient thermo-metallurgical model was developed to study the technique with titanium alloys to get a better understanding of the thermal and metallurgical underlying aspects. The calculated temperatures and phase transformations are compared with experimental tests. © 2011 Published by Elsevier Ltd., This work is has been done under the research project MAT2008-06882-C04 funded by the Spanish government (MICIIN).