Pasar al contenido principal

NANOMATERIALES CON ALTA CAPACIDAD DE RECONOCIMIENTO MODULABLE ELECTRONICAMENTE, TIPO ON-OFF,PARA SU APLICACION EN BIOSENSORES ELECTROQUIMICOS CON CARACTERISTICAS EXCEPCIONALES

MAT2011-25870

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario FUNDACIÓ INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

An integrated phenol 'sensoremoval' microfluidic nanostructured platform

  • Mayorga-Martinez, Carmen C.|||0000-0003-3687-0035
  • Hlavatá, Lenka
  • Miserere, Sandrine|||0000-0003-2311-621X
  • López Marzo, Adaris María|||0000-0001-8552-8637
  • Labuda, Ján|||0000-0001-6953-6522
  • Pons Picart, Josefina|||0000-0003-1834-9326
  • Merkoçi, Arben|||0000-0003-2486-8085
Phenol is a widely used chemical that for several reasons may be released into the environment and, consequently, its detection and subsequent destruction into the ground and surface waters are of special importance. Herein, a simple lab-on-a-chip (LOC) device based on biocompatible and biodegradable CaCO- poly(ethyleneimine) (PEI) nanostructured microparticles (MPs) to detect and remove phenolic wastes is proposed. The detection of phenol using a hybrid polydimethylsiloxane (PDMS)/glass chronoimpedimetric microchip and its removal in the same LOC system through the use of an extra CaCO-PEI MPs microcolumn is achieved. For the first time, the chronoimpedance technique is applied in a LOC system for phenol sensing in a range of 0.01-10μM achieving the limit of detection (LOD) of 4.64nM. Moreover, this device shows a high repeatability with a relative standard deviation of 3% which is almost 4 times lower than that for the chronoamperometry technique. This LOC system represents an integrated platform for phenol sensing and removal (sensoremoval) that can be easily fabricated and is of a low cost, disposable and amenable to mass production.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Magnetic bead/gold nanoparticle double-labeled primers for electrochemical detection of isothermal amplified Leishmania DNA

  • De La Escosura-Muñiz, Alfredo|||0000-0002-9600-0253
  • Baptista Pires, Luis Miguel|||0000-0002-2290-6386
  • Serrano, Lorena
  • Altet Sanahujes, Laura
  • Francino, Olga|||0000-0002-9022-3835
  • Sánchez Bonastre, Armando|||0000-0001-9160-1124
  • Merkoçi, Arben|||0000-0003-2486-8085
A novel methodology for the isothermal amplification of Leishmania DNA using labeled primers combined with the advantages of magnetic purification/preconcentration and the use of gold nanoparticle (AuNP) tags for the sensitive electrochemical detection of such amplified DNA is developed. Primers labeled with AuNPs and magnetic beads (MBs) are used for the first time for the isothermal amplification reaction, being the amplified product ready for the electrochemical detection. The electrocatalytic activity of the AuNP tags toward the hydrogen evolution reaction allows the rapid quantification of the DNA on screen-printed carbon electrodes. Amplified products from the blood of dogs with Leishmania (positive samples) are discriminated from those of healthy dogs (blank samples). Quantitative studies demonstrate that the optimized method allows us to detect less than one parasite per microliter of blood (8 × 10⁻³ parasites in the isothermal amplification reaction). This pioneering approach is much more sensitive than traditional methods based on real-time polymerase chain reaction (PCR), and is also more rapid, cheap, and user-friendly.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Control of Electron-transfer in Immunonanosensors by Using Polyclonal and Monoclonal Antibodies

  • Mars, Abdelmoneim
  • Parolo, Claudio|||0000-0001-9481-4408
  • De La Escosura-Muñiz, Alfredo|||0000-0002-9600-0253
  • Raouafi, Noureddine
  • Merkoçi, Arben|||0000-0003-2486-8085
The design and operation of biosensors is not trivial. For instance, variation in the output signal during monitoring of analytes can not usually be controlled. Hence, if such control were possible, and could be triggered on demand, it would greatly facilitate system design and operation. Herein, we report the design of two types of voltamperometric immunosensors, in which the magnitude of the current output signal (differential pulse voltammetry [DPV]) can be increased or decreased as needed. The designed systems use monoclonal and polyclonal anti-human IgG antibodies, conjugated to monopodal ferrocene-modified gold nanoparticles that are casted onto screen-printed carbon electrodes (Ab/mFcL/AuNPs/SPCEs). Upon addition of human IgG as antigen, the systems exhibit opposite responses according to the Ab: the current decreases when monoclonal Ab is used, whereas it increases when polyclonal Ab is used. We attributed the former response to inhibition of electron-transfer (due to the formation of a protein layer), and the latter response, to a global increase in electron transfer (induced by the aggregation of gold nanoparticles). These effects were confirmed by studying a custom-made lipoic acid-based bipodal ligand, which confirmed that the increase in current is effectively induced by the aggregation of the modified nanoparticles (pAb/mFcL/AuNPs). Both sensors have large dynamic ranges, although the pAb-based one was found to be 3.3-times more sensitive. Tests of selectivity and specificity for ovalbumin, α-lactalbumin and serum bovine albumin showed that the immunosensors are highly selective and specific, even in the presence of up to 1000-fold levels of potentially competitive proteins. The limit of detection for human IgG using the pAb/mFcL/AuNP bioconjugate was estimated to be 0.85 ng/mL. The pAb/mFcL/AuNPs-based biosensor has used to determine amounts of human IgG in real sample.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

An iridium oxide nanoparticle and polythionine thin film based platform for sensitive Leishmania DNA detection

  • Mayorga Martinez, Carmen
  • Chamorro García, Alejandro|||0000-0003-0953-5848
  • Serrano, Lorena
  • Rivas, Lourdes|||0000-0002-1510-5927
  • Quesada-González, Daniel|||0000-0003-3064-2146
  • Altet Sanahujes, Laura
  • Francino, Olga|||0000-0002-9022-3835
  • Sánchez Bonastre, Armando|||0000-0001-9160-1124
  • Merkoçi, Arben|||0000-0003-2486-8085
An impedimetric label-free genosensor for high sensitive DNA detection is developed. This system is based on a screen-printed carbon electrode modified with the thionine layer and iridium oxide nanoparticles (IrO₂ NP/). An aminated oligonucleotide probe is immobilized on the IrO₂ NP/polythionine modified electrode and ethanolamine was used as a blocking agent. Different diluted PCR amplified DNA samples have been detected. The selectivity and reproducibility of this system are studied and the system was highly reproducible with RSD ≈ 15% and sensitive enough while using 2% of ethanolamine during the blocking step employed for genosensor preparation.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Alzheimer's disease biomarkers detection in human samples by efficient capturing through porous magnetic microspheres and labelling with electrocatalytic gold nanoparticles

  • De La Escosura-Muñiz, Alfredo|||0000-0002-9600-0253
  • Plichta, Zdeněk
  • Horák, Daniel|||0000-0002-6907-9701
  • Merkoçi, Arben|||0000-0003-2486-8085
A nanobiosensor based on the use of porous magnetic microspheres (PMM) as efficient capturing/pre-concentrating platform is presented for detection of Alzheimer's disease (AD) biomarkers. These PMMs prepared by a multistep swelling polymerization combined with iron oxide precipitation afford carboxyl functional groups suitable for immobilization of antibodies on the particle surface allowing an enhanced efficiency in the capturing of AD biomarkers from human serum samples. The AD biomarkers signaling is produced by gold nanoparticle (AuNP) tags monitored through their electrocatalytic effect towards hydrogen evolution reaction (HER). Novel properties of PMMs in terms of high functionality and high active area available for enhanced catalytic activity of the captured AuNPs electrocatalytic tags are exploited for the first time. A thorough characterization by scanning transmission electron microscope in high angle annular dark field mode (STEM-HAADF) demonstrates the enhanced ability of PMMs to capture a higher quantity of analyte and consequently of electrocatalytic label, when compared with commercially available microspheres. The optimized and characterized PMMs are also applied for the first time for the detection of beta amyloid and ApoE at clinical relevant levels in cerebrospinal fluid (CSF), serum and plasma samples of patients suffering from AD.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Annexin-V/quantum dot probes for multimodal apoptosis monitoring in living cells, Improving bioanalysis using electrochemistry

  • Montón i Domingo, Helena
  • Parolo, Claudio|||0000-0001-9481-4408
  • Aranda-Ramos, Antonio|||0000-0003-3476-7026
  • Merkoçi, Arben|||0000-0003-2486-8085
  • Nogués, Carme|||0000-0002-6361-8559
There is a great demand to develop novel techniques that allow useful and complete monitoring of apoptosis, which is a key factor of several diseases and a target for drug development. Here, we present the use of a novel dual electrochemical/optical label for the detection and study of apoptosis. We combined the specificity of Annexin-V for phosphatidylserine, a phospholipid expressed in the outer membrane of apoptotic cells, with the optical and electrochemical properties of quantum dots to create a more efficient label. Using this conjugate we addressed three important issues: (i) we made the labeling of apoptotic cells faster (30 min) and easier; (ii) we fully characterized the samples by common cell biological techniques (confocal laser scanning microscopy, scanning electron microscopy and flow cytometry); and (III) we developed a fast, cheap and quantitative electrochemical detection method for apoptotic cells with results in full agreement with those obtained by flow cytometry.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrochemical Impedance Spectroscopy (bio)sensing through hydrogen evolution reaction induced by gold nanoparticles

  • Mayorga-Martinez, Carmen C.|||0000-0003-3687-0035
  • Chamorro García, Alejandro|||0000-0003-0953-5848
  • Merkoçi, Arben|||0000-0003-2486-8085
A new gold nanoparticle (AuNP) based detection strategy using Electrochemical Impedance Spectroscopy (EIS) through hydrogen evolution reaction (HER) is proposed. This EIS-HER method is used as an alternative to the conventional EIS based on [Fe(CN)] or [Ru(NH)] indicators. The proposed method is based on the HER induced by AuNPs. EIS measurements for different amounts of AuNP are registered and the charge transfer resistance (R) was found to correlate and be useful for their quantification. Moreover the effect of AuNP size on electrical properties of AuNPs for HER using this sensitive technique has been investigated. Different EIS-HER signals generated in the presence of AuNPs of different sizes (2, 5, 10, 15, 20, and 50nm) are observed, being the corresponding phenomena extendible to other nanoparticles and related catalytic reactions. This EIS-HER sensing technology is applied to a magneto-immunosandwich assay for the detection of a model protein (IgG) achieving improvements of the analytical performance in terms of a wide linear range (2-500ngmL) with a good limit of detection (LOD) of 0.31ngmL and high sensitivity. Moreover, with this methodology a reduction of one order of magnitude in the LOD for IgG detection, compared with a chroamperometric technique normally used was achieved.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Alzheimer disease biomarker detection through electrocatalytic water oxidation induced by iridium oxide nanoparticles

  • Rivas, Lourdes|||0000-0002-1510-5927
  • De La Escosura-Muñiz, Alfredo|||0000-0002-9600-0253
  • Pons Picart, Josefina|||0000-0003-1834-9326
  • Merkoçi, Arben|||0000-0003-2486-8085
Iridium oxide nanoparticles (IrO NPs) synthesized following a previously reported chemical route are presented as novel tags for immunosensing taking advantage of their electrocatalytic activity towards water oxidation reaction (WOR). Cyclic voltammetry and chronoamperometry for the evaluation of the IrO NPs electrocatalytic activity towards WOR at neutral pH were used. The chronoamperometric current recorded at a fixed potential of +1.3V constituted the analytical signal allowing the quantification of IrO NPs at nM levels. Modification of the surface of citrate-capped IrO NPs with anti-Apolipoprotein E antibodies (αApoE) was successfully achieved and the as-prepared conjugates were used for the electrocatalytic detection of ApoE Alzheimer disease (AD) biomarker in a magnetosandwich immunoassay, reaching a detection limit of 68ng/mL. Human plasma of a patient suffering AD was also evaluated, estimating an ApoE concentration of 20μg/mL which is in concordance with the obtained in previously reported approaches. This novel IrO NPs based electrocatalytic assay presents the advantage of the signal generation in the same medium where the immunoassay takes place (PBS, pH7.4) avoiding the use of additional reagents which also opens the way to future integrated biosensing systems and platforms with interest for other proteins as well as DNA and cells analysis.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Hybrid self-assembled materials constituted by ferromagnetic nanoparticles and tannic acid, A theoretical and experimental investigation

  • Santos, Anderson F. M.
  • Macedo, Lucyano J. A.
  • Chaves, Mariana H.
  • Espinoza Castañeda, Marisol
  • Merkoçi, Arben|||0000-0003-2486-8085
  • Lima, Francisco das Chagas A.
  • Cantanhêde, Welter
Hybrid magnetite materials are interesting for both biomedical and catalytic applications due to their well-known biocompatibility, as well as their magnetic and electric properties. In this work we prepared Fe O nanoparticles (NPs) coated with tannic acid (TA), a natural polyphenol, through two different synthetic routes, aiming to understand the influence of TA in the synthesis step and contribute to the development of water-dispersible magnetic materials. The coating process was verified by information obtained from transmission electron microscopy (TEM), zeta-potential and Fourier transform infrared (FTIR) spectroscopy. The incorporation of TA after Fe O NPs production generated spherical NPs smaller than 10 nm, suggesting that TA plays a fundamental role in the nucleation and organization of Fe O NPs. Data from both density functional theory (DFT) and FTIR allowed us to infer that Fe O interacts mainly with the carbonyl groups of TA. Hybrid materials having improved water-dispersibility are very attractive for biomedical applications.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Improving sensitivity of gold nanoparticle-based lateral flow assays by using wax-printed pillars as delay barriers of microfluidics

  • Rivas, Lourdes|||0000-0002-1510-5927
  • Medina Sánchez, Mariana|||0000-0001-6149-3732
  • De La Escosura-Muñiz, Alfredo|||0000-0002-9600-0253
  • Merkoçi, Arben|||0000-0003-2486-8085
Although lateral flow assays (LFAs) are currently being used in some point-of-care applications (POC), they cannot still be extended to a broader range of analytes for which higher sensitivities and lower detection limits are required. To overcome such drawbacks, we propose here a simple and facile alternative based on the use of delay hydrophobic barriers fabricated by wax printing so as to improve LFA sensitivity. Several wax pillar patterns were printed onto the nitrocellulose membrane in order to produce delays as well as pseudoturbulence in the microcapillary flow. The effect of the proposed wax pillar-modified devices was also mathematically simulated, corroborating the experimental results obtained for the different patterns tested afterwards for detection of HIgG as model protein in a gold nanoparticle-based LFA. The effect of the introduction of such wax-printed pillars was a sensitivity improvement of almost 3-fold compared to the sensitivity of a conventional free-barrier LFA.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

An inkjet-printed field-effect transistor for label-free biosensing

  • Medina Sánchez, Mariana|||0000-0001-6149-3732
  • Martinez Domingo, Carme|||0000-0002-1897-5362
  • Ramon, Eloi|||0000-0001-9974-8112
  • Merkoçi, Arben|||0000-0003-2486-8085
A flexible, biological field-effect transistor (BioFET) for use in biosensing is reported. The BioFET is based on an organic thin-film transistor (OTFT) fabricated mainly by inkjet printing and subsequently functionalized with antibodies for protein recognition. The BioFET is assessed for label-free detection of a model protein, human immunoglobulin G (HIgG). It is characterized electrically to evaluate the contribution of each step in the functionalization of the OTFT and to detect the presence of the target protein. The fabrication, structure, materials optimization, electrical characteristics, and functionality of the starting OTFT and final BioFET are also discussed. Different materials are evaluated for the top insulator layer, with the aim of protecting the lower layers from the electrolyte and preserving the BioFET electrical performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Extremely fast and high Pb²⁺ removal capacity using a nanostructured hybrid material

  • López Marzo, Adaris María|||0000-0001-8552-8637
  • Pons Picart, Josefina|||0000-0003-1834-9326
  • Merkoçi, Arben|||0000-0003-2486-8085
Ultra-fast toxic metal removal using a hybrid and nanostructured vaterite-poly(ethyleneimine) (NV-PEI) is reported. Especially for Pb²⁺ , an extremely high and fast adsorption capacity without precedents is observed. Within a 3 min contact time (CT), 97-100% of Pb²⁺ contaminant in water samples at pH 6, with a large concentration range (from 2 to 1000 ppm) and using a dosage of 0.5 g NV-PEI per L, has been removed. The maximum adsorption capacity (q ) calculated for a 1500 ppm Pb initial concentration was 2762 mg of Pb²⁺ per g NV-PEI. In addition to the excellent Pb removal, this material is cheap, easy to synthesize, biocompatible, and biodegradable, which makes it superior to others reported to date and an attractive alternative for the treatment of industrial wastewaters.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ferrocene-functionalized graphene electrode for biosensing applications

  • Rabti, Amal|||0000-0001-8404-5393
  • Mayorga-Martinez, Carmen C.|||0000-0003-3687-0035
  • Baptista Pires, Luis Miguel|||0000-0002-2290-6386
  • Raouafi, Noureddine
  • Merkoçi, Arben|||0000-0003-2486-8085
A novel ferrocene-functionalized reduced graphene oxide (rGO)-based electrode is proposed. It was fabricated by the drop casting of ferrocene-functionalized graphene onto polyester substrate as the working electrode integrated within screen-printed reference and counter electrodes. The ferrocene-functionalized rGO has been fully characterized using FTIR, XPS, contact angle measurements, SEM and TEM microscopy, and cyclic voltammetry. The XPS and EDX analysis showed the presence of Fe element related to the introduced ferrocene groups, which is confirmed by a clear CV signal at ca. 0.25 V vs. Ag/AgCl (0.1 KCl). Mediated redox catalysis of HO and bio-functionalization with glucose oxidase for glucose detection were achieved by the bioelectrode providing a proof for potential biosensing applications.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced detection of quantum dots labeled protein by simultaneous bismuth electrodeposition into microfluidic channel

  • Medina Sánchez, Mariana|||0000-0001-6149-3732
  • Miserere, Sandrine|||0000-0003-2311-621X
  • Cadevall Riera, Miquel|||0000-0002-2968-5862
  • Merkoçi, Arben|||0000-0003-2486-8085
In this study, we propose an electrochemical immunoassay into a disposable microfluidic platform, using quantum dots (QDs) as labels and their enhanced detection using bismuth as an alternative to mercury electrodes. CdSe@ZnS QDs were used to tag human IgG as a model protein and detected through highly sensitive stripping voltammetry of the dissolved metallic component (cadmium in our case). The modification of the screen printed carbon electrodes (SPCEs) was done by a simple electrodeposition of bismuth that was previously mixed with the sample containing QDs. A magneto-immunosandwich assay was performed using a micromixer. A magnet placed at its outlet in order to capture the magnetic beads used as solid support for the immunoassay. SPCEs were integrated at the end of the channel as detector. Different parameters such as bismuth concentration, flow rate, and incubation times, were optimized. The LOD for HIgG in presence of bismuth was 3.5 ng/mL with a RSD of 13.2%. This LOD was about 3.3-fold lower than the one obtained without bismuth. Furthermore, the sensitivity of the system was increased 100-fold respect to experiments carried out with classical screen-printed electrodes, both in presence of bismuth.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrocatalytic tuning of biosensing response through electrostatic or hydrophobic enzyme-graphene oxide interactions

  • Baptista Pires, Luis Miguel|||0000-0002-2290-6386
  • Pérez-López, Briza
  • Mayorga-Martinez, Carmen C.|||0000-0003-3687-0035
  • Morales-Narváez, Eden|||0000-0002-1536-825X
  • Domingo Marimon, Neus|||0000-0002-5229-6638
  • Esplandiu Egido, Maria José|||0000-0003-2079-0639
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Merkoçi, Arben|||0000-0003-2486-8085
The effect of graphene oxidative grades upon the conductivity and hydrophobicity and consequently the influence on an enzymatic biosensing response is presented. The electrochemical responses of reduced graphene oxide (rGO) have been compared with the responses obtained from the oxide form (oGO) and their performances have been accordingly discussed with various evidences obtained by optical techniques. We used tyrosinase enzyme as a proof of concept receptor with interest for phenolic compounds detection through its direct adsorption onto a screen-printed carbon electrode previously modified with oGO or rGO with a carbon-oxygen ratio of 1.07 or 1.53 respectively. Different levels of oGO directly affect the (bio)conjugation properties of the biosensor due to changes at enzyme/graphene oxide interface coming from the various electrostatic or hydrophobic interactions with biomolecules. The developed biosensor was capable of reaching a limit of detection of 0.01. nM catechol. This tuning capability of the biosensor response can be of interest for building several other biosensors, including immunosensors and DNA sensors for various applications