Pasar al contenido principal

RECUBRIMIENTOS DE BARRERA TERMICA PARA LA MEJORA DE LAS PROPIEDADES SUPERFICIALES DE ACEROS AUSTENITICOS Y DUPLEX

MAT2011-28492-C03-03

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDADE DA CORUÑA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tribology and high temperature friction wear behavior of MCrAlY laser cladding coatings on stainless steel

  • Pereira, Juan Carlos
  • Zambrano, Jenny
  • Licausi, Marie-Pierre
  • Tobar, Maria
  • Amigó, Vicente|||0000-0002-2107-0273
Temperature can have a significant effect on the extent of wear damage of metallic components. Thermal barrier coatings can improve the high temperature tribological and friction wear behavior. In this work the dry friction and wear behavior at low and high temperature of NiCoCrAlY and CoNiCrAlY laser cladding coatings were evaluated, as well as for the austenitic stainless steel AISI 304 used as substrate. Dense coatings, with good bonding to the substrate was obtained by coaxial laser cladding tracks (40% overlapping), with previously optimized laser parameters. Tribological wear tests were performed by sliding wear at room temperature and 500 ºC, with an Al2O3 ball on disk configuration tribometer. The wear scar surface was evaluated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) microanalysis. The 3D topography of the wear track was determined by inductive contact profilometer which enabled the wear rate calculation. The microstructure of the coatings consists of γNi/β-NiAl or γCo/β-(Co,Ni)Al phases depending on the chemical composition of the alloy, as confirmed by X-ray diffraction (XRD) analysis. The wear test results show a reduction in wear rate at high temperature for all materials tested. For the NiCoCrAlY coating, the high temperature also reduces the friction coefficient, while it significantly increases the friction coefficient of CoNiCrAlY coating. The main damage mode is abrasion and adhesion, caused by the oxide and partially-oxidized particles in the contact surface. The coatings and substrate results were compared, resulting in an improved wear behavior., The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. Professor Juan Carlos Pereira Falcon thanks the University of Carabobo (Grant CD3997-2011) for the financial support to pursue his doctoral studies at the UPV. Furthermore, the authors thank Dr. Jose Luis Jorda for the XRD analysis.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High temperature oxidation behavior of laser cladding MCrAlY coatings on austenitic stainless steel

  • Pereira, Juan Carlos
  • Zambrano, J.C.
  • Tobar, M.J.
  • Yañez, A.
  • Amigó, Vicente|||0000-0002-2107-0273
The development of coatings has become technologically significant in many industries. A common approach in high temperature applications is the production of new thermal barrier coatings (TBCs). Laser cladding (LC) can be an alternative method to thermal spraying in the production of high quality bond coats in TBCs. In this work, dense coatings that formed adequate metallurgical bondswith the substrate were obtained by overlapping coaxial laser cladding. The oxidation behavior of the coating specimens was assessed by air furnace oxidation tests at 1100 °C for up to 200 h. The coatings' microstructures are composed of a γ matrix phase and a β interdendritic phase, confirmed by X-ray diffraction (XRD). At high temperatures, the growth and formation of oxide layers protect the underlying coating and substrate from oxidation at elevated temperatures. The possible formation and morphology of oxides on the oxidized surface were evaluated using scanning electron microscopy (SEM), XRD and atom force microscopy (AFM). The evaluation of the thickness and phases present in thermally grown oxide scales was evaluated using field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy microanalysis (EDS), with a previous cut using the Focused Ion Beam Ga Column (FIB) method., The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. Professor Juan Carlos Pereira Falcon thanks the University of Carabobo for the financial support to pursue his doctoral studies at the UPV.