Pasar al contenido principal

CARACTERIZACION DE RECUBRRIMIENTOS DE BARRERA TERMICA OBTENIDOS POR LASER

MAT2011-28492-C03-01

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of Laser Surface Melting on Ti 30Nb 2Sn Sintered Alloy

  • Candel Bou, Juan José
  • Amado, Jose Manuel
  • Tobar, María José
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser surface melting (LSM) is used to simultaneously melt a thin layer and quench Ti¿30Nb¿2Sn substrate produced by powder metallurgy route. Results show LSM is useful to eliminate non-desirable open porosity and to reduce even more the Young Modulus. The best microstructure is achieved below the melting pool where high peak temperature combined with high cooling rate during laser processing is present. LSM retains beta titanium without traces of martensite or grain boundary alpha due to oxygen contamination., This work is financially supported by Spanish Ministry of Science (Grant No. MAT2011-28492-C03-01 and BES-2009-013589) and PIB2010BZ-00448 International project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Recubrimientos laser cladding de TiAl sobre Ti6Al4V: Caracterización tribológica, TiAl laser cladding coatings on Ti6Al4V: Tribological characterization

  • Zambrano-Carrullo, Jenny Cecilia
  • Cárcel González, Bernabé
  • Pereira-Falcon, Juan Carlos
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The Ti6Al4V has proven an important engineering alloy due to its good properties such as the excellent strength, weight ratio, high corrosion resistance and biocompatibility. However, the alloy is susceptible to mechanical degradation in applications involving sliding wear or abrasion. In order to improve wear resistance has been deposited by laser cladding on Ti6Al4V alloy a titanium-aluminum intermetallic alloy. For the realization of coatings different process parameters, such as laser power, scanning speed, powder feeding rate and the preheating temperature were optimized. The microstructure of the coatings was evaluated using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Furthermore tribological properties were obtained, using a ball on disk tribometer, with Al2O3 ball, constant speed of 0.1 m/s, 10 N load at temperature 24 °C and 500 °C. We evaluated 3D surface topography obtained by the wear scar with an inductive contact profilometer and calculating from it the volume removed and the wear rate. The microstructure of the coatings consists of ¿-TiAl phase and ¿2-Ti3Al. The wear test results at room temperature show a lower wear rate for the coatings compared to the substrate. At high temperature the coatings have a higher friction coefficient and a higher rate of wear is obtained when compared with the substrate. The coatings have good metallurgical bond, although the presence of cracks and the different wear mechanisms have an influence on the wear resistance at elevated temperatures., [ES] El Ti6Al4V ha demostrado ser una importante aleación de ingeniería debido a sus buenas propiedades tales como la excelente relación resistencia/peso, alta resistencia a la corrosión y biocompatibilidad. Sin embargo, la aleación es propensa a la degradación mecánica en aplicaciones que implican desgaste por deslizamiento o abrasión. Con la finalidad de mejorar su resistencia al desgaste, se ha desarrollado recubrimientos por laser cladding coaxial sobre láminas de Ti6Al4V, con una aleación de titanio aluminio Ti48Al2Cr2Nb. Para la realización de los recubrimientos se optimizaron diferentes parámetros de proceso, tales como potencia, velocidad de pasada, caudal de polvo suministrado y temperatura de calentamiento del sustrato. Se determinó la microestructura de los recubrimientos obtenidos mediante microscopía óptica (MO), microscopía electrónica de barrido (MEB) y difracción de rayos X (DRX). Por otro lado se obtuvieron propiedades tribológicas mediante ensayos de desgaste utilizando un tribómetro en configuración del tipo bola sobre disco, con bola de Al2O3, velocidad de 0.1 m/s, carga de 10 N, a temperaturas de ensayo de 24 ºC y 500 ºC. La topografía 3D de la huella de desgaste fue obtenida con un perfilómetro inductivo de contacto, a partir de ella el volumen removido y la tasa de desgaste. La microestructura de los recubrimientos se compone de fases ¿-TiAl y ¿2-Ti3Al. En los ensayos de desgaste a temperatura ambiente los resultados muestran una tasa de desgaste menor por parte de los recubrimientos comparados con el sustrato. A elevada temperatura los recubrimientos presentan un mayor coeficiente de fricción, y además, se obtiene una mayor tasa de desgaste cuando se compara con el sustrato. Los recubrimientos presentan buena adherencia en general, observándose que la presencia de grietas influye en la resistencia al desgaste a elevadas temperaturas, así como en los diferentes mecanismos de desgaste observados., Los autores agradecen el apoyo financiero del Ministerio de Ciencia e Innovación del Gobierno de España a través del proyecto de investigación MAT2011-28492-C03 y a la Generalitat Valenciana a través del apoyo ACOMP/2014/151. Se agradece además al Dr. José Luis Jordá del Instituto de Tecnología Química de la UPV, por los análisis de difracción de rayos X realizados.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of process parameters and initial microstructure on the oxidation resistance of Ti48Al2Cr2Nb coating obtained by laser metal deposition

  • Zambrano Carrullo, Jenny Cecilia
  • Pereira Falcón, Juan Carlos
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Ti6Al4V have been the most important and versatile titanium alloys currently used, due to their excellent combination of low density and good mechanical properties, despite their application temperature being limited to up to 300 °C. In this work, a Ti6Al4V sheet was coated with a Ti48Al2Cr2Nb alloy by laser cladding process, with the process parameters resulting in laser-specific energy densities of 70, 80, 90 and 180 J/mm2, laser power between 600 and 900W and scanning speed of 100 to 300 mm/min. In order to analyze the oxidation resistance at elevated temperature, isothermal oxidation tests were carried out at 800 °C for 5, 10, 25, 50, 100 and 150 h in static air. The oxidized samples were characterized by optical microscopy (OM), scanning electron microscopy (SEM), field emission microscopy (FESEM) with energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) analysis. Two groups of coatings with similar microstructures were obtained, and their influence on the formation of thermally oxidized growth layers was studied. From the isothermal oxidation tests, it was observed that the Ti48Al2Cr2Nb coatings have good resistance to oxidation in air at 800 °C in comparison with the Ti6Al4V substrate by obtaining layers of oxides up to 12 ¿m thick after 150 h of oxidation. The structure of the oxide layers is complex and comprises the growth of successive layers from the outer surface of the coating. The effect of the microstructure of the coating on the density of the oxide layer formed was evaluated., The authors would like to thank the Ministerio de Ciencia e Innovacion of the Spanish Government for their financial support through research project MAT2011-28492-C03 and the Generalitat Valenciana through grant ACOMP/2014/151.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical and microstructural characterization of MCrAlY coatings produced by laser cladding: The influence of the Ni, Co and Al content

  • Pereira, J. C.
  • Zambrano, J. C.
  • Yañez, A.
  • E. Rayón|||0000-0002-0653-2046
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser metal deposition (LMD) and laser cladding (LC) are alternative methods to thermal spraying processes to produce dense, high-quality coatings. In this work, two MCrAlY coatings (M=Ni+Co) have been prepared onto stainless steel substrate using a coaxial LC technique under two different Ni/Co and Al proportions. The mechanical properties were then evaluated with microhardness, nanoindentation, and three-point bending tests. The microstructure and composition of coatings were characterized by X-ray Diffraction (XRD) analysis and Field Emission Electron Microscopy (FESEM) coupled to an Energy Dispersive Spectroscopy (EDS) detector. The study revealed that the ¿/ß phases formed in the MCrAlY coating microstructure result in a lower elastic modulus than the austenitic stainless steel substrate, while an inverse behavior for hardness was observed due the presence of the aluminum-rich ß-phase. Under flexural loads, the failure of coatings showed plasticity and anisotropy characteristics depending on the two laser tracks orientations evaluated., The authors would like to acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03, and the support of the Generalitat Valenciana through ACOMP/2013/114
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tribology and high temperature friction wear behavior of MCrAlY laser cladding coatings on stainless steel

  • Pereira, Juan Carlos
  • Zambrano, Jenny
  • Licausi, Marie-Pierre
  • Tobar, Maria
  • Amigó, Vicente|||0000-0002-2107-0273
Temperature can have a significant effect on the extent of wear damage of metallic components. Thermal barrier coatings can improve the high temperature tribological and friction wear behavior. In this work the dry friction and wear behavior at low and high temperature of NiCoCrAlY and CoNiCrAlY laser cladding coatings were evaluated, as well as for the austenitic stainless steel AISI 304 used as substrate. Dense coatings, with good bonding to the substrate was obtained by coaxial laser cladding tracks (40% overlapping), with previously optimized laser parameters. Tribological wear tests were performed by sliding wear at room temperature and 500 ºC, with an Al2O3 ball on disk configuration tribometer. The wear scar surface was evaluated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) microanalysis. The 3D topography of the wear track was determined by inductive contact profilometer which enabled the wear rate calculation. The microstructure of the coatings consists of γNi/β-NiAl or γCo/β-(Co,Ni)Al phases depending on the chemical composition of the alloy, as confirmed by X-ray diffraction (XRD) analysis. The wear test results show a reduction in wear rate at high temperature for all materials tested. For the NiCoCrAlY coating, the high temperature also reduces the friction coefficient, while it significantly increases the friction coefficient of CoNiCrAlY coating. The main damage mode is abrasion and adhesion, caused by the oxide and partially-oxidized particles in the contact surface. The coatings and substrate results were compared, resulting in an improved wear behavior., The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. Professor Juan Carlos Pereira Falcon thanks the University of Carabobo (Grant CD3997-2011) for the financial support to pursue his doctoral studies at the UPV. Furthermore, the authors thank Dr. Jose Luis Jorda for the XRD analysis.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Análisis Geométrico y Microestructural de Recubrimientos de NiCoCrAlYTa proyectados por láser sobre láminas de acero inoxidable AISI 316L, Geometric and microstructural analysis of laser CLAD nococralyta coating on stainless steel AISI 316L

  • Pereira-Falcon, Juan Carlos
  • Candel Bou, Juan José
  • Amado P., José M.
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] In this work, the NiCoCrAlYTa Alloy was deposited by laser cladding with different processing parameters (flow rate of powder supplied, feed speed and laser power), in order to analyze the effects of processing on the geometry, microstructure and properties of the coating. We have measured the dimensions of the tracks by optical microscopy and computer image analysis. Scanning electron microscopy (SEM) and energy dispersive spectroscopy microanalysis (EDS) have been used to analyze the microstructure, chemical composition and microhardness variations. The coatings exhibit good geometric aspect ratio without cracks and macro pores, and a good metallurgical bond with the substrate through the dilution zone was obtained; yet there is no a homogeneous columnar dendrite structure that depends on the processing laser. It has been observed that the surface hardness of the coating is twice that of the substrate hardness. The EDS microanalysis evidenced the dilution and mixing of relevant chemical elements such as Fe, Co, Al and Ta with Ni-Cr, generating a gradual variation between substrate and coating which influences the hardening observed at the interface., [ES] En este estudio se ha evaluado recubrimientos de NiCoCrAlYTa depositados sobre AISI 316L mediante la técnica de deposición láser (laser cladding), con diferentes parámetros de proceso (caudal de polvo aportado, velocidad de avance y potencia del láser), con la finalidad de analizar la influencia del procesado sobre la geometría, microestructura y propiedades del recubrimiento. Se ha medido las dimensiones de los recubrimientos mediante microscopía óptica y análisis de imágenes, y se ha estudiado la microestructura, variación de composición química y de microdureza, mediante microscopía electrónica de barrido (MEB) y microanálisis por espectroscopía de energía dispersiva (EDS). Los recubrimientos obtenidos presentan una adecuada relación de aspecto geométrica y no presentan macro defectos importantes, existe una buena unión metalúrgica con el sustrato, con una adecuada área de dilución; no obstante, existe una estructura dendrítica columnar no homogénea que depende del procesado láser. Se ha observado que la dureza en la zona próxima a la superficie del recubrimiento duplica la dureza del sustrato. Los microanálisis por EDS evidencian la disolución y mezcla de elementos químicos relevantes como el Fe, Co, Al y Ta con el Ni-Cr, que generan una variación gradual entre sustrato y recubrimiento que influye en el endurecimiento observado en la intercara del recubrimiento., Los autores agradecen al Ministerio de Economía y Competitividad del Gobierno de España la financiación recibida a través del proyecto de investigación MAT2011-28492-C03 y a la Generalitat Valenciana (ACOMP/2013/114). Este trabajo se ha desarrollado de manera conjunta entre el Instituto de Tecnología de Materiales de la Universidad Politécnica de Valencia y el Departamento de Ingeniería Industrial II de la Universidade da Coruña. El Profesor Juan Carlos Pereira Falcón agradece a la Universidad de Carabobo-Venezuela por la beca otorgada para realizar estudios doctorales en la Universidad Politécnica de Valencia-España.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High temperature oxidation behavior of laser cladding MCrAlY coatings on austenitic stainless steel

  • Pereira, Juan Carlos
  • Zambrano, J.C.
  • Tobar, M.J.
  • Yañez, A.
  • Amigó, Vicente|||0000-0002-2107-0273
The development of coatings has become technologically significant in many industries. A common approach in high temperature applications is the production of new thermal barrier coatings (TBCs). Laser cladding (LC) can be an alternative method to thermal spraying in the production of high quality bond coats in TBCs. In this work, dense coatings that formed adequate metallurgical bondswith the substrate were obtained by overlapping coaxial laser cladding. The oxidation behavior of the coating specimens was assessed by air furnace oxidation tests at 1100 °C for up to 200 h. The coatings' microstructures are composed of a γ matrix phase and a β interdendritic phase, confirmed by X-ray diffraction (XRD). At high temperatures, the growth and formation of oxide layers protect the underlying coating and substrate from oxidation at elevated temperatures. The possible formation and morphology of oxides on the oxidized surface were evaluated using scanning electron microscopy (SEM), XRD and atom force microscopy (AFM). The evaluation of the thickness and phases present in thermally grown oxide scales was evaluated using field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy microanalysis (EDS), with a previous cut using the Focused Ion Beam Ga Column (FIB) method., The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. Professor Juan Carlos Pereira Falcon thanks the University of Carabobo for the financial support to pursue his doctoral studies at the UPV.