Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of Laser Surface Melting on Ti 30Nb 2Sn Sintered Alloy

  • Candel Bou, Juan José
  • Amado, Jose Manuel
  • Tobar, María José
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser surface melting (LSM) is used to simultaneously melt a thin layer and quench Ti¿30Nb¿2Sn substrate produced by powder metallurgy route. Results show LSM is useful to eliminate non-desirable open porosity and to reduce even more the Young Modulus. The best microstructure is achieved below the melting pool where high peak temperature combined with high cooling rate during laser processing is present. LSM retains beta titanium without traces of martensite or grain boundary alpha due to oxygen contamination., This work is financially supported by Spanish Ministry of Science (Grant No. MAT2011-28492-C03-01 and BES-2009-013589) and PIB2010BZ-00448 International project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comportamiento frente a la oxidación de aleaciones de titanio alfa + beta

  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
  • Schalht, A.
  • Amigó Mata, Angèlica
[EN] Las aleaciones alfa+beta, presentan excelentes propiedades mecánicas y frente a la corrosión lo que las hace excelentes candidatas para su aplicación en la industria química y aeronáutica, pero es importante mejorar su comportamiento frente a elevadas temperaturas, sobre todo su oxidación a esas temperaturas. En el presente trabajo se estudia la obtención de aleaciones + del tipo Ti-3%at. X (Nb, Mo, Ta) por vía pulvimetalúrgica a partir de mezcla elemental de polvos y su caracterización microestructural, con análisis específico de su resistencia a la oxidación a elevadas temperaturas. La microestructura se caracteriza mediante microscopía óptica y electrónica. La resistencia mecánica de las aleaciones se obtiene mediante ensayos de flexión y análisis fractográfico. La resistencia frente a la oxidación se ha determinado mediante una termobalanza Q50 de TA Instruments a 900º durante 200 minutos. Los mecanismos de corrosión se han analizado a través de sus óxidos superficiales, caracterizados mediante microscopía electrónica de barrido (SEM) y microscopía de fuerza atómica (AFM). Todas las aleaciones investigadas presentan estructura + con densidades entre el 90 y 94%. Además, presentan elevada resistencia a flexión, alrededor de los 1750-1800 MPa de carga de rotura, y elevada dureza; con una resistencia a la oxidación sensiblemente mayor que la correspondiente al titanio puro comercial. La difracción de rayos-X (XRD) y espectroscopia Raman confirman la formación de óxidos de titanio como fase principal. En conclusión la adición de los elementos de aleación aumenta en dos veces su resistencia frente a la oxidación a elevadas temperaturas., Los autores agradecen al MINECO la financiación del proyecto de investigación bilateral con Brasil PIB2010BZ-00448, a la UE por la financiación FEDER UPOV08-3E-005 para la compra de equipamiento y a la Generalitat Valenciana por la ayuda ACOMP/2013/094.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Efecto de las variables de proceso sobre el comportamiento a flexión de aleaciones Ti - 3% at. X (X = Nb, Ta) obtenidas por pulvimetalurgia, Effect of process variables on the flexural behavior of alloys Ti - 3% at. X (X = Nb, Ta) obtained by powder metallurgy

  • Franconetti Rodríguez, Patricia
  • Candel Bou, Juan José
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[ES] El niobio y el tantalio se añaden al titanio para formar nuevas aleaciones beta con mayor biocompatibilidad para aplicaciones biomédicas. Ambos elementos tienen un elevado punto de fusión, por lo que su difusión en estado sólido es limitada. En este trabajo se han fabricado por pulvimetalurgia muestras de titanio con 3% atómico de niobio o tantalio. Se estudia el efecto de la presión de compactación, la temperatura y el tiempo de sinterizado sobre la resistencia, la elasticidad y la ductilidad a flexión. Los resultados muestran que ambos elementos se comportan de manera semejante: aumenta la resistencia entre 20-25%, la elasticidad entre 0-10% y la ductilidad en más de un 150%. Por tanto, la adición de estos elementos es beneficiosa para las propiedades mecánicas. El análisis estadístico muestra que el efecto de la temperatura y presión son importantes mientras que el efecto del tiempo es poco significativo e incluso perjudicial en estas aleaciones., [EN] Niobium and tantalum are added to titanium alloys to form new beta alloys with higher biocompatibility for biomedical applications. Both elements have a high melting point, that is the reason for their limited solid state diffusion. In this work samples of titanium with 3% at. niobium and tantalum have been manufactured by powder metallurgy. The effect of the compacting pressure, temperature and the sintering time on the strength, elasticity and ductility in bending has been studied. The results show that both elements behave similarly: flexural strength increases between 20-25%, elasticity between 0-10% and ductility over 150%. Therefore, the addition of these elements is beneficial to mechanical properties. Statistical analysis shows that the effect of temperature and pressure are important, while the effect of time is insignificant and even harmful in these alloys., Los autores agradecen al MINECO la financiación a través del programa de Formación de Personal Investigador con la ayuda BES-2009-013589 así como a través del proyecto de investigación bilateral con Brasil PIB2010BZ-00448. Este trabajo se ha desarrollado en la Unidad de Tecnología de Materiales de la Universidad Politécnica de Valencia asociada al CSIC a través del Centro Nacional de Investigaciones Metalúrgicas (CENIM). Por último, agradecer a la UE por la financiación recibida a través del FEDER en el proyecto UPOV08-3E-005 para la compra de equipamiento y a la Generalitat Valenciana por la ayuda ACOMP/2012/094.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and Mechanical Behavior of Porous Ti-6Al-4V Processed by Spherical Powder Sintering

  • Reig Cerdá, Lucía
  • Tojal Domenech, Concepcion
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • Amigó, Vicente|||0000-0002-2107-0273
Reducing the stiffness of titanium is an important issue to improve the behavior of this material when working together with bone, which can be achieved by generating a porous structure. The aim of this research was to analyze the porosity and mechanical behavior of Ti-6Al-4V porous samples developed by spherical powder sintering. Four different microsphere sizes were sintered at temperatures ranging from 1300 to 1400 degrees C for 2, 4 and 8 h. An open, interconnected porosity was obtained, with mean pore sizes ranging from 54.6 to 140 mu m. The stiffness of the samples diminished by as much as 40% when compared to that of solid material and the mechanical properties were affected mainly by powder particles size. Bending strengths ranging from 48 to 320 MPa and compressive strengths from 51 to 255 MPa were obtained., The authors are grateful to the Spanish Ministry of Economy and Competitiveness for supporting this research by Project PIB2010BZ-00448. They also thank the Universitat Jaume I for funding the translation of this paper.