Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of laser irradiation on failure mechanism of TiCp reinforcedtitanium composite coating produced by laser cladding

  • Candel Bou, Juan José
  • Jiménez, J.A.
  • Franconetti Rodríguez, Patricia
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser cladding is an effective technique to coat a metallic substrate with a layer of a different nature.It has been widely reported that the most important combined parameters controlling the quality ofthe coating are the specific energy (E) and the powder density ( ). In the present work, clad depositsof Ti6Al4V + 60 wt.% TiC were prepared on a Ti6Al4V substrate using an optimum combination of Ec= 24 J/mm2 and c= 3 mg/mm2. These experiments were performed using a laser power of 400 and600 W, in order to study the effect of laser power on the properties of the clad. The microstructure, phasecomposition and nanohardness of the coatings were investigated by optical microscopy, scanning elec-tron microscopy and X-ray diffraction. During laser processing, TiC can be partially converted to TiCX(X = 0.5) due mainly to the TiC dissolution into the laser-generated melting pool and subsequent precipi-tation during cooling. It was observed that the lower laser power limit reduces primary TiC dissolution butit also promotes secondary carbide alignment at the interface. On the other hand, the damage mechanisminduced by high laser power is dominated by primary TiC particle cracking by the high stress concentra-tion at the particle matrix interface followed by ductile failure of the matrix. It is also remarkable thatirradiance affects the TiC/TiCxratio despite Ecand care fixed and it determines hardness distributioninside the coating., Authors thank MINECO funding in special the Training of Research Staff programme with the help BES-2009-013589 and the support of the Comision Interministerial de Ciencia y Tecnologia (CICYT), Spain, under Grant MAT2012-39124. This work was developed at the Materials Technology Unit of the Polytechnic University of Valencia associated to CSIC through the National Centre for Metallurgical Research (CENIM). Finally, thank the EU for the funding received through the FEDER help in the project UPOV08-3E-005 for the purchase of equipment and the Generalitat Valenciana for the help ACOMP/2012/094.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of Laser Surface Melting on Ti 30Nb 2Sn Sintered Alloy

  • Candel Bou, Juan José
  • Amado, Jose Manuel
  • Tobar, María José
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser surface melting (LSM) is used to simultaneously melt a thin layer and quench Ti¿30Nb¿2Sn substrate produced by powder metallurgy route. Results show LSM is useful to eliminate non-desirable open porosity and to reduce even more the Young Modulus. The best microstructure is achieved below the melting pool where high peak temperature combined with high cooling rate during laser processing is present. LSM retains beta titanium without traces of martensite or grain boundary alpha due to oxygen contamination., This work is financially supported by Spanish Ministry of Science (Grant No. MAT2011-28492-C03-01 and BES-2009-013589) and PIB2010BZ-00448 International project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Titanium Metal Matrix Composite Laser Coatings Based on Carbides

  • Amigó, Vicente|||0000-0002-2107-0273
  • Candel Bou, Juan José
  • Franconetti Rodríguez, Patricia
Laser cladding is an adequate technique to fabricate Metal Matrix Composite (MMC) layers because of its focused high energy which allows the partial melting of hard ceramic reinforces particles like carbides. Thus, the wettability and gradual transition between metal and particle can be improved. However, metastable or new intermetallic phases can be formed during laser processing due to severe thermal cycle imposed to the clad with unknown properties in some cases. In this work our experience on microstructural analysis of Ti-MMC coatings acquired during the last five years is summarized. Special attention is paid on carbide dilution and secondary carbides formation mechanisms when TiC, SiC, Cr3C2, WC and B4C are mixed with titanium alloys., This work is financially supported by Spanish Ministry of Science (Grant No. MAT2008-06882- C04-03/04 and BES-2009-013589) under the National Industrial Production Programme.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Efecto de las variables de proceso sobre el comportamiento a flexión de aleaciones Ti - 3% at. X (X = Nb, Ta) obtenidas por pulvimetalurgia, Effect of process variables on the flexural behavior of alloys Ti - 3% at. X (X = Nb, Ta) obtained by powder metallurgy

  • Franconetti Rodríguez, Patricia
  • Candel Bou, Juan José
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[ES] El niobio y el tantalio se añaden al titanio para formar nuevas aleaciones beta con mayor biocompatibilidad para aplicaciones biomédicas. Ambos elementos tienen un elevado punto de fusión, por lo que su difusión en estado sólido es limitada. En este trabajo se han fabricado por pulvimetalurgia muestras de titanio con 3% atómico de niobio o tantalio. Se estudia el efecto de la presión de compactación, la temperatura y el tiempo de sinterizado sobre la resistencia, la elasticidad y la ductilidad a flexión. Los resultados muestran que ambos elementos se comportan de manera semejante: aumenta la resistencia entre 20-25%, la elasticidad entre 0-10% y la ductilidad en más de un 150%. Por tanto, la adición de estos elementos es beneficiosa para las propiedades mecánicas. El análisis estadístico muestra que el efecto de la temperatura y presión son importantes mientras que el efecto del tiempo es poco significativo e incluso perjudicial en estas aleaciones., [EN] Niobium and tantalum are added to titanium alloys to form new beta alloys with higher biocompatibility for biomedical applications. Both elements have a high melting point, that is the reason for their limited solid state diffusion. In this work samples of titanium with 3% at. niobium and tantalum have been manufactured by powder metallurgy. The effect of the compacting pressure, temperature and the sintering time on the strength, elasticity and ductility in bending has been studied. The results show that both elements behave similarly: flexural strength increases between 20-25%, elasticity between 0-10% and ductility over 150%. Therefore, the addition of these elements is beneficial to mechanical properties. Statistical analysis shows that the effect of temperature and pressure are important, while the effect of time is insignificant and even harmful in these alloys., Los autores agradecen al MINECO la financiación a través del programa de Formación de Personal Investigador con la ayuda BES-2009-013589 así como a través del proyecto de investigación bilateral con Brasil PIB2010BZ-00448. Este trabajo se ha desarrollado en la Unidad de Tecnología de Materiales de la Universidad Politécnica de Valencia asociada al CSIC a través del Centro Nacional de Investigaciones Metalúrgicas (CENIM). Por último, agradecer a la UE por la financiación recibida a través del FEDER en el proyecto UPOV08-3E-005 para la compra de equipamiento y a la Generalitat Valenciana por la ayuda ACOMP/2012/094.