Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of synthesis conditions on electrical and catalytical properties of perovskites with high value of A-site cation size mismatch

  • Vidal, Karmele
  • Larrañaga, Aitor
  • Morán-Ruiz, Aroa
  • Laguna-Bercero, M. A.
  • Arriortua, María Isabel
et al., The perovskite La0.15Sm0.35Sr0.08Ba0.42FeO3-δ has been prepared by the glycine nitrate route, varying the calcination temperature, fuel/oxidizer ratio and cooling rate, in order to study the sample preparation influence on the properties in the context of their application as a electrode material for SOFCs. The obtained materials have been characterized by X-ray diffraction, scanning electron microscopy, electrical and BET surface area measurements, and also the reaction between oxygen and CO, which can occur in SOFCs during the conversion of chemical energy into electrical energy. As overall results, all the samples present a phase segregation showing two perovskites with rhombohedral structure. SEM images show a well-necked morphology of the powders which are composed of nanosized particles and agglomerations of grains. The BET specific surface area of the samples decreases as calcination temperature increases, as well as for the quenched sample. The measured electronic conductivity values (<50 S/cm) are characteristic for samples with these high values of σ(r) (A cation size disorder). The catalytic activity tests for the CO oxidation reaction showed a T50% (“light-off temperature”, defined as the temperature at which 50% conversion of CO is achieved) value about 440°C–450 °C, CO conversion reaching 100% at approximately 600 °C for all the prepared perovskites. Then, for the La0.15Sm0.35Sr0.08Ba0.42FeO3-δ perovskite, CO conversion temperature is lower than usual SOFCs operating temperature. This points out to the technological interest of these materials in the framework of reducing the operating temperature of SOFCs., This research has been funded by the Ministerio de Ciencia e Innovación (CONSOLIDER-INGENIO 2010 CSD2009-00013), Ministerio de Economía y Competitividad (MAT2013-42092-R and MAT2012-30763), the Feder program of the Europen Union and Dpto. Educación, Política Lingüística y Cultura of the Basque Goverment (IT-630-13). The authors thank for technical and human support provided by SGIker of UPV/EHU. K. Vidal thanks UPV/EHU for funding., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nuevas cromitas de composición La1‐xMxCr0.9Ni0.1O3 (M=Sr, Nd, Ca; x<0.3) con tamaño de A y desorden fijados, para su uso como ánodos de pilas SOFCs

  • Ortega-San-Martín, L.
  • Vidal, Karmele
  • Larrañaga, Aitor
  • Laguna-Bercero, M. A.
  • Arriortua, María Isabel
Póster presentado al XIV Congreso Nacional de Materiales celebrado en Gijón del 8 al 10 de junio de 2016., El desarrollo de nuevos materiales y la optimización de las técnicas de fabricación son claves para conseguir reducir la temperatura de operación, y con ello, el coste, de sistemas de generación de energía como las pilas de combustible de óxido sólido, SOFC. Los métodos de combustión, se proponen como la vía de síntesis para la preparación de materiales a emplear en esta tecnología. Los ánodos habituales de las pilas SOFC son cermets de metales como el níquel o cobre junto con el material de electrolito (ceria o circonia dopadas). Entre los principales problemas de esos ánodos está el de la deposición de carbón cuando se usan combustibles económicos como el metano. En este sentido, se ha observado que el óxido de cromo dopado con estroncio (La,Sr)CrO3, además de ser un buen conductor electrónico tipo p, no cataliza la deposición de carbono, por lo que es un ánodo potencial para la oxidación directa de metano. Las cromitas son buenas conductoras de la electricidad (dopadas o sin dopar), pero su actividad catalítica mejora considerablemente si el dopaje se da con metales de transición (Mn,Fe,Co,Ni,Cu) en la posición del cromo. En esta investigación se ha realizado un estudio del efecto del dopaje en A, pero fijando el tamaño promedio de A (en 1.22 Å) y el desorden de esta posición (0.0001 Å2), que está asociado a la diferencia de tamaños de esos elementos. Se han sintetizado cuatro compuestos de la serie La1‐xMxCr0.9Ni0.1O3 (M=Sr, Nd, Ca o sus combinaciones; con x=0.10, 0.15, 0.20 y 0.25) mediante el método de combustión con glicina‐nitrato. Los resultados preliminares por difracción de rayos X en muestra policristalina indican que son fases rómbicas con simetría Pnma. En el presente trabajo se mostrarán los resultados de tamaño de grano de los mismos, estudiados por microscopía electrónica de barrido (MEB) y los datos de conductividad electrónica y dilatometría (TEC)., Esta investigación ha sido financiada por el Dpto. Educación, Política Lingüística y Cultura del Gobierno Vasco (IT-630-13) y por el Ministerio de Economía y Competitividad (MAT2013-42092-R). Los autores agradecen a los SGIker por el apoyo técnico (UPV/EHU) y a la ayuda recibida del Fondo Europeo de Desarrollo Regional (FEDER)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Celdas de pilas de oxidó sólido. Avance en el procesado de materiales

  • Wain-Martin, A.
  • Morán-Ruiz, Aroa
  • Vidal, Karmele
  • Larrañaga, Aitor
  • Laguna-Bercero, M. A.
  • Arriortua, María Isabel
Póster presentado al XIV Congreso Nacional de Materiales celebrado en Gijón del 8 al 10 de junio de 2016., Este trabajo está enfocado a la síntesis y al procesado de los componentes de las pilas de combustible de óxido sólido (SOFC). La configuración empleada consiste en celdas (ánodo/electrolito/cátodo) soportadas por el electrolito. Se han sintetizado los compuestos, NiO-(ZrO2)0.92(Y2O3)0.08, (ZrO2)0.92(Y2O3)0.08 y La0.6Sr0.4FeO3 como ánodo, electrolito y cátodo, respectivamente. Con objeto de disminuir la reactividad electrolito-cátodo, se ha empleado una barrera Ce0.8Sm0.2O1.9 entre ambos componentes. En buen acuerdo con K. Vidal y col. se ha utilizado la técnica de combustión por glicina-nitrato para la síntesis de los compuestos. La evaluación de la pureza, morfología y conductividad se ha llevado a cabo mediante difracción de rayos X (XRD) (método Rietveld), microscopía electrónica de barrido (MEB) y medidas de conductividad en bulk a través del método de cuatro puntos. Para el procesado del electrolito se ha empleado una prensa hidráulica, obteniéndose pastillas de 20 mm de diámetro y 500μm de espesor. Éstas se han sinterizado a 1450 ºC durante 4 h en aire, con objeto de alcanzar las propiedades físico-químicas adecuadas. La deposición del ánodo, cátodo y barrera se ha realizado por spray manual coloidal, empleándose una solución en base orgánica. Para analizar el comportamiento electroquímico de la estructura multicapa, se han realizado medidas de impedancia a 800 ºC durante 100 h. La degradación de los sistemas se ha estudiado a partir de análisis por energía dispersiva de rayos X (EDX) mediante el análisis de las micrografías de las secciones transversales., Esta investigación ha sido financiada por el Dpto. Educación, Política Lingüística y Cultura del Gobierno Vasco (IT-630-13) y al Ministerio de Economía y Competitividad (MAT2013-42092-R). Los autores agradecen a SGIker por el apoyo técnico (UPV/EHU, MEC, GV/EJ and European Social Fund) y a la ayuda recibida del Fondo Europeo de Desarrollo Regional (FEDER)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Biomimetic catalysts based on metalloporphyrin MOFs

  • Fidalgo-Marijuan, Arkaitz
  • Barandika, Gotzone
  • Bazán, Begoña
  • Urtiaga, Miren Karmele
  • Larrea, Edurne S.
  • Iglesias, Marta
  • Arriortua, María Isabel
Poster presented at the 12th European Biological Inorganic Chemistry Conference, held in Zurich (Switzerland), August 24-28 2014., During the past years, a great effort has been devoted to the anchoring of catalysts into MOFs in order to achieve heterogeneous catalysts. In this sense, an innovative approach consists on using metalloporphyrins as coordination-network synthons mimicking their natural catalytic activity in order to reproduce it in the solid state. The work herein presented explores the activity of μ-O-[FeTCPP]2·nDMF (TCPP= meso-tetracarboxyphenylporphyrin; n≈16) and [CoTPPS0.5(bipy)(H2O)2]·6H2O (TPPS= meso-tetrasulfonatophenylporphyrin, bipy= 4,4´-bipyridine) compounds as heterogeneous catalysts on oxidation and acetylation reactions of different organic substrates., This work has been financially supported by the "Ministerio de Economía y Competitividad" (MAT2013-42092-R, MAT2011-29020-C02-02), the "Gobierno Vasco" (Basque University System Research Groups, IT-630-13) and the UPV/EHU (UFI 11/5) which we gratefully acknowledge. Technical and human support provided by SGIker (UPV/EHU, MICINN, GV/EJ, ESF) is gratefully acknowledged. A Fidalgo-Marijuan thanks the UPV/EHU for funding.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Scalable synthetic method for SOFC compounds

  • Wain-Martin, A.
  • Morán-Ruiz, Aroa
  • Vidal, Karmele
  • Larrañaga, Aitor
  • Laguna-Bercero, M. A.
  • Arriortua, María Isabel
Although economically competitive SOFC systems seems to be ready for commercialization, a broad inventory of key starting materials and fabrication processes are needed to enhance systems and reduce costs. These necessities are raised by the demands for large scale SOFC industrial production. Taking into account these reasons, we have synthesized the mean components of a fuel cell, on a large scale, by the glycine nitrate combustion method. The synthesized different components of SOFC have been the interconnector protective coating (MnCo1.9Fe0.1O4), contact layer (LaNi0.6Fe0.4O3), cathode (La0.6Sr0.4FeO3), interlayer (Sm0.2Ce0.8O1.9), electrolyte (ZrO2)0.92(Y2O3)0.08 and anode (Ni0.3O-(ZrO2)0.92(Y2O3)0.08) material, obtaining reproducible pure samples and amounts up to 12 g for each batch, being able to increase easily this amount to lots of hundred of grams. The obtained materials have been characterized by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and X-ray fluorescence (XRF), X-ray diffraction (XRD), dilatometry, scanning electron microscopy (SEM), particle size distribution and conductivity measurements., This research has been funded by the Ministerio de Economía, Industria y Competitividad (MAT2016-76739-R) (AEI/FEDER, UE) and (MAT2015-2015-86078-R) and Dpto. Educación of the Basque Goverment (IT-630-13). The authors thanks the support received by the European Regional Development Fund (ERDF). SGIker of UPV/EHU technical support is gratefully acknowledged. A. Wain-Martin thanks Ministerio de Economía y Competitividad for funding his work (BES-2014-068433)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mixed Metal-Organic Framework as a Heterogeneous Catalyst

  • Larrea, Edurne S.
  • Fernández de Luis, Roberto
  • Orive, Joseba
  • Iglesias, Marta
  • Arriortua, María I.
The synthesis of a new mixed metal-organic framework (M′MOF) has been accomplished by the metalloligand approach. [NaCu(2,4-HPdc)(2,4-Pdc)] (2,4-H2Pdc = pyridine-2,4-dicarboxylic acid) has been obtained from the hydrothermal reaction of the metalloligand [Cu(2,4-HPdc)2(H2O)2] NaOH, and a transition metal salt. [NaCu(2,4-HPdc)(2,4-Pdc)] is isostructural to [CuMn(2,4-Pdc)2] and crystallizes in the triclinic space group P$\bar {1}$. The 3D structure is built up from [Cu(2,4-HPdc)2(H2O)2] metalloligands and [NaO6] octahedra in a pcu α-Po-like uninodal six-connected net. The compound is stable to 290 °C, and its crystal structure undergoes a 3 % volume expansion between room temperature and thermal decomposition. The unsaturated CuII centers at the surface act as a heterogeneous Lewis acid catalyst for the cyanosilylation of aldehydes and Knoevenagel C-C bond-forming reactions. The catalytic activity has been compared with those of other copper(II) porous metal-organic frameworks such as HKUST-1 and MOF-74., This work was financially supported by the Ministerio de Economía y Competitividad (MEC) (grant numbers MAT2013‐42092‐R, MAT2011‐29020‐C02‐02), the Gobierno Vasco (Basque University Research System Group) (IT‐630‐13), and University of the Basque Country (UPV/EHU) (UFI 11/15).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Heterogeneous catalytic activity on Mn, Fe and Co-based metalloporphyrinic Solid Coordination Frameworks (SCFs)

  • Fidalgo-Marijuan, Arkaitz
  • Barandika Argoitia, Miren Gotzone
  • Bazán Blau, Begoña del Pilar
  • Urtiaga Greaves, Miren Karmele
  • Serrano Larrea, Edurne
  • Iglesias, Marta
  • Arriortua, María Isabel
Poster presented at the 1st European Conference on Metal Organic Frameworks and Porous Polymers, held in Potsdam (Germany) on October 11-14th, 2015., Solid Coordination Frameworks (SCFs) have been widely explored on different catalytic reactions, and during the past years metalloporphyrins have been investigating in order to mimick it in the solid state their natural activity. Herein we present the catalytic activity results towards the oxidation reactions of different alcohols for MnTPPS, FeTCPP and CoTPPS based metalloporphyrinc SCFs (TPPS= meso-tetrasulfonatophenylporphyrin, TCPP= meso-tetracarboxyphenylporphyrin). Additionally, Knoevenagel condensations and a one-pot reaction involving the FeTCPP based SCF catalysts have been carried out., This work has been financially supported by the Ministerio de Economía y Competitividad (MAT2013-42092-R), the Gobierno Vasco (IT-630-13) and the UPV/EHU (UFI 11/15), which we gratefully acknowledge. Technical and human support provided by SGIker (UPV/EHU) is gratefully acknowledged. A. Fidalgo-Marijuan thanks the UPV/EHU for the postdoctoral contract.