Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The relation between ductility at high temperature and solid solution in Mg alloys

  • Cepeda-Jiménez, C.M.
  • Shi, D.F.
  • Pérez Prado, María Teresa
This work investigates the effect of solid solution on ductility and on the activation of individual deformation mechanisms at moderate temperatures and at quasi-static strain rates in Mg-Zn and Mg-Al alloys. With that aim, four solid solution Mg-Zn and Mg-Al binary alloy ingots containing 1 and 2 wt.% solute atoms were subjected to hot rolling and subsequent annealing to generate polycrystals with similar average grain size and basal-type texture for each composition. The activity of the different slip systems after tensile testing at 150°C and at 250°C was evaluated in pure Mg and in the alloys by EBSD-assisted slip trace analysis. In addition, segregation of Zn and Al atoms at grain boundaries during the thermo-mechanical processing was characterized by HAADF-STEM and EDX. It was found that while the addition of Al and Zn atoms to pure Mg does not lead to major changes in the mechanical strength at the investigated temperatures, it does enhance ductility significantly, especially at 250°C. Our results show that this increase in ductility cannot be attributed to a higher activation of non-basal systems in the alloys, as reported earlier, as the incidence of non-basal systems is indeed considerably higher in pure Mg. This work suggests, on the contrary, that the ductility increase may be attributed to the presence of a more homogenous basal activity in the alloys due to a lower degree of orientation clustering, to grain boundary solute segregation, and to a higher slip diffusivity at grain interiors., The research leading to these results has received funding from the Madrid region under programme S2018/NMT-4381-MAT4.0-CM project. Funding from projects PID2019-111285RB-I00 and PID2020-118626RB-I00 awarded by the Spanish Ministry of Science, Innovation and Universities, is also acknowledged. DFS acknowledges the financial support from the China Scholarship Council (Grant no 201706050154).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the isothermal bainitic transformation and austenite stability in an advanced Al-rich medium-Mn steel

  • Morawiec, M.
  • Ruiz-Jiménez, Víctor
  • García Mateo, Carlos
  • Jiménez, José Antonio
  • Grajcar, Adam
Isothermal bainitic transformation of a lean medium-Mn steel containing (in mass%) 0.18C–3.6Mn–1.7Al–0.23Si–0.2Mo–0.04–Nb after full austenitization at 1100 ºC was studied by means of high resolution dilatometry. The effects of isothermal holding temperatures ranging from 450 to 350 °C on the bainitic transformation kinetics was studied experimentally characterizing the microstructure present after a holding time ranging from 15 min to 2 h. The obtained results showed that the bainitic transformation is uncompleted at temperatures above 425 °C. The carbon enrichment of the austenite during isothermal treatment at 450 °C and 425 °C is not enough to avoid martensitic transformation of the austenite during cooling to room temperature. Thus, it is obtained a mixed structure including bainitic ferrite and martensite. Decreasing the austempering temperature resulted in a more pronounced bainite formation. The kinetics of the transformation during austempering at 350ºC is quite similar to that observed at 400 °C, so that 60 min are needed in both cases to complete the reaction. However, local variations in chemical composition associated to segregation of Mn and Al during casting solidification results in differences in the transformation rate of bainitic reaction between different areas in the material. A balance difference between the dendritic and interdendritic areas is responsible for the differences observed among test samples in the kinetics of the isothermal bainitic transformation and the final microstructure., The financial support of the National Science Center, Poland, is gratefully acknowledged, grant no. 2017/27/B/ST8/02864. JAJ and CG-M would like to acknowledge the Comunidad de Madrid and the Spanish Ministry of Science and Innovation for the financial support by means of the MAT4.0-CM and AFORMAR (PID2019-109334RB) projects respectively.
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

A Methodology to Automatically Segment 3D Ultrasonic Data Using X-ray Computed Tomography and a Convolutional Neural Network

  • Caballero Garzón, Juan Ignacio|||0000-0003-3759-6146
  • Cosarinsky, Guillermo|||0000-0002-6148-7612
  • Camacho, Jorge|||0000-0001-7528-558X
  • Menasalvas Ruiz, Ernestina|||0000-0002-5615-6798
  • Gonzalo Martí­n, Consuelo|||0000-0002-0804-9293
  • Sket, Federico|||0000-0001-5075-3180
Archivo Digital UPM
Publicación Contribución de congreso (ConferenceOutput)

The Role of Process Design and Modelling in the Quality Assurance of Additively Manufactured Metallic Components

  • Ocaña Moreno, José Luis|||0000-0001-9263-8404
  • Cordovilla Baró, Francisco|||0000-0001-7438-2804
  • Angulo Ramonell, Ignacio
  • García Beltrán, Ángel|||0000-0003-1900-0222
  • Radhakrishnan, J.
  • Warzanskyj Prieto, Wsewolod|||0000-0002-7121-2022
  • Díaz Muñoz, Marcos|||0000-0001-7751-4913
  • Porro González, Juan Antonio|||0000-0001-5260-527X