Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Chemical and electrochemical study of fabrics coated with reduced graphene oxide

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Fernández Sáez, Javier
  • Del Río García, Ana Isabel
Polyester fabrics coated with reduced graphene oxide (RGO) have been obtained and later characterized by means of chemical and electrochemical techniques. X-ray photoelectron spectroscopy showed a decrease of the oxygen content as well as an increase of the sp2 fraction after chemical reduction of graphene oxide (GO). The electrical conductivity was measured by electrochemical impedance spectroscopy (EIS) and showed a decrease of 5 orders of magnitude in the resistance (¿) when GO was reduced to RGO. The phase angle also changed from 90° for PES-GO (capacitative behavior) to 0° for RGO coated fabrics (resistive behavior). In general an increase in the number of RGO layers produced an increase of the conductivity of the fabrics. EIS measurements in metal/sample/electrolyte configuration showed better electrocatalytic properties and faster diffusion rate for RGO specimens. Scanning electrochemical microscopy was employed to test the electroactivity of the different fabrics obtained. The sample coated with GO was not conductive since negative feedback was obtained. When GO was reduced to RGO the sample behaved like a conducting material since positive feedback was obtained. Approach curves indicated that the redox mediator had influence on the electrochemical response. The Fe(CN)63¿/4¿ redox mediator produced a higher electrochemical response than Ru(NH3)63+/2+ one., Authors thank to the Spanish Ministerio de Ciencia e Innovacion (contract CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support. J. Molina is grateful to the Conselleria d'Educacio (Generalitat Valenciana) for the FPI fellowship. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y Tecnologia for the FPI fellowship. J.C. Galvan is gratefully acknowledged for help with EIS measurements and data analysis.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis and characterization of electrochemically Platinum-Polyaniline modified carbon textile electrode

  • Fernández Sáez, Javier
  • Del Río García, Ana Isabel
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] The present work deals with the use of a carbon fiber fabric for electrochemical purposes. To carry out such investigation, suitable working electrodes of C, Pt/C and Pt/PANI/C were manufactured. Two types of electrodes were made from: Yarns pulled out from the woven textile (CYEs) and strips, 1 cm x 2 cm area, cut from the fabric (CSEs). Cyclic voltammetry (CV) was employed to carry out the electrosynthesis processes. Cyclic and linear voltammetry, electrochemical impedance spectroscopy (EIS) and scanning electrochemical microscopy (SECM) were used to study the electrocatalytic properties of carbon modified electrodes (CMEs). X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were used to know the chemical composition and to describe the morphology of the Pt/PANI/C and Pt/C modified surfaces. Sulphuric and amaranth solutions were chosen for the electrochemical experiments considering the possible applications of CMEs in the field of electrochemical treatment of industrial wastewater polluted with azo dyes., The authors would like to acknowledge to the Spanish Ministry of Science and Innovation (MICINN) for the financial support (CTM2010-18842-C02-02 and CTM 2011-23583), to the Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support and to the company Carbongen S.A., Cocentaina, Spain, that kindly donated the activated carbon fabric.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis of Pt nanoparticles on electrochemically reduced graphene oxide by potentiostatic and alternate current methods

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Fernández Sáez, Javier
  • Del Río García, Ana Isabel
Reduced graphene oxide (RGO) has been synthesized on Pt wires by means of a potentiodynamic method between +0.6 V and -1.4'V for 20 scans. Cyclic voltammetry characterization of the coatings showed the typical capacitative behavior of graphene. Pt nanoparticles were synthesized on Pt-RGO electrodes by means of potentiostatic methods and a comparison between different synthesis potentials (-0.16, 0, +0.2 and +0.4 V) for the same synthesis charge (mC.cm(-2)) was established. The electrodes obtained were characterized in 0.5 M H2SO4 solution to observe the characteristic oxidation and reduction processes of the Pt surface. A 0.5 M H2SO4/0.5 M CH3OH solution was used to measure the catalytic properties of the deposits against methanol oxidation. The most appropriate potential to perform the synthesis was 0 V followed by -0.16 V and +0.2 V. The morphology of the coatings varied depending on the potential applied as observed by scanning electron microscopy. Alternate current methods were also used to synthesize Pt nanoparticles and compare the results with the traditional potentiostatic method. Different frequencies were used: 0.1, 1, 10, 100, 1000 and 10000 Hz. Alternate current synthesis is more efficient than traditional potentiostatic methods, obtaining more electroactive coatings with less effective synthesis time. (C) 2014 Elsevier Inc. All rights reserved., Authors wish to thank to the Spanish Ministerio de Ciencia e Innovacion (contract CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support. J. Molina is grateful to the Conselleria d'Educacio, Formacio i Ocupacio (Generalitat Valenciana) for the Programa VALi+D Postdoctoral Fellowship. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y Tecnologia for the FPI fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of azo dyes on Pt and Pt/polyaniline/dispersed Pt electrodes

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Fernández Sáez, Javier
  • Del Río García, Ana Isabel
The electrochemical characterization of two organic dyes (amaranth and procion orange MX-2R) has been performed on Pt electrodes and Pt electrodes coated with polyaniline and dispersed Pt. Electrodes with different Pt loads have been synthesized and characterized obtaining that a load of 300 ¿g cm -2 was the optimum one. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) was employed to observe the distribution and morphology of the Pt nanoparticles. The electroactivity of the electrodes has also been characterized by means of scanning electrochemical microscopy (SECM). The chemical characterization of Pt dispersed Pani coated Pt electrodes (Pt-Pani-Pt) was performed by means of X-ray photoelectron spectroscopy (XPS). The electrochemical characterization of the dyes has been performed by means of cyclic voltammetry. Voltammograms have shown that the presence of the dyes diminishes characteristic Pt oxidation and reduction peaks. However, redox processes due to the dyes, appeared in the voltammograms. The different species responsible of these redox processes were generated in the vicinity of the electrode and were not adsorbed on the electrode surface since after stirring, the different redox processes disappeared. Characterization with different scan rates showed that redox processes of both dyes were controlled by diffusion. © 2012 Elsevier B.V., Authors thank to the Spanish Ministerio de Ciencia e Innovacion and European Union Funds (FEDER) (contracts CTM2010-18842-C02-02 and CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support. J. Molina is grateful to the Conselleria d'Educacio (Generalitat Valenciana) for the FPI fellowship. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y Tecnologia for the FPI fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modified carbon fabric electrodes: preparation and electrochemical behavior toward amaranth electrolysis

  • Fernández Sáez, Javier
  • Del Río García, Ana Isabel
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
The electrochemical behavior of non-modified, Pt-modified, and Pt/polyaniline-modified carbon fiber textile electrodes was studied through a series of electrolyses, under potentiostatic conditions, on an amaranth/sulfuric solution in the presence or absence of chloride ion. The morphology of the dispersed Pt, PANI, and PANI/Pt coatings was analyzed by scanning electron microscopy. Scanning electrochemical microscopy confirmed that the textile surface was effectively modified by the electrocatalytic material. Color removal reached values above 90 % in both electroreduction and electrooxidation processes. The amaranth electroreductions carried out with the non-modified electrode showed better charge efficiency than those with the Pt-modified textile electrode. The electrooxidations with Pt-modified textile electrodes showed a significant reduction in electrolysis time. Ultraviolet-visible and Fourier transform infrared with attenuated total reflection spectra enabled the electrochemical behavior of the non-modified and Pt/PANI-modified electrodes to be distinguished., The authors wish to acknowledge to the Spanish Ministerio de Ciencia e Innovacion (contract CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support; and as well as Carbongen S. A. (Cocentaina, Spain), who kindly donated the activated carbon fabric. J. Molina is grateful to the Conselleria d'Educacio, Formacio i Ocupacio (Generalitat Valenciana) for the Programa VALi+D Postdoctoral Fellowship. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y Tecnologia for the FPI fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical treatment of solutions containing a recalcitrant dye: A way of using dimensionally adaptable catalytic fabrics

  • Del Río García, Ana Isabel
  • García, Carolina
  • Fernández Sáez, Javier
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
The objective of this work is to study the decolorization/degradation of reactive dye Remazol Black (RMZB) in sulfuric media. The electrochemical behavior was evaluated by cyclic voltammetry (CV) using platinum (Pt) and glassy carbon (GC) as working electrodes. Different electrolyses were performed potentioscally using Pt, activated carbon textile (ACT) and activated carbon textile electrocatalytically improved with dispersed Pt (Pt-ACT) with and without NaCl. The decolorization was studied by UV-visible spectroscopy. High performance liquid chromatography (HPLC) also permitted us to confirm the dye degradation. Specific applied charge (Q/Ah L-1) was evaluated and the efficiencies of the dye degradation were discussed in terms of electrical energy per order (E-EO/kWh m(-3) order(-1)). Field emission scanning electron microscopy (FESEM) was used to observe the morphological differences of a Pt-ACT electrode before and after the electrolyses, confirming that the corverage of dispersed Pt remains on the surface., The authors thank the Spanish Ministerio de Ciencia e Innovacion (contract CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for the financial support. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y Tecnologia for her FPI fellowship. J. Molina is grateful to the Conselleria d'Educacio, Formacio i Ocupacio (Generalitat Valenciana) for the Program VALi+D Postdoctoral Fellowship. C. Garcia is grateful to the Conselleria d'Educacio, Formacio i Ocupacio (Generalitat Valenciana) for her Geronimo Forteza fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical characterization of reduced graphene oxide-coated polyester fabrics

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Fernández Sáez, Javier
  • Inés Vilches, Juan Carlos
  • Del Río García, Ana Isabel
Reduced graphene oxide (RGO) coated fabrics were obtained by chemical reduction of GO on polyester (PES) fabrics. Conducting fabrics that have different applications were obtained by applying several layers of RGO. Electrochemical techniques not traditionally used for the characterization of these materials were used to test their electrical and electrochemical properties. Electrochemical impedance spectroscopy was used to measure the electrical properties. The resistance of the original PES was more than 10(11) Omega cm(2), but when coated with three RGO layers, the resistance decreased to 23.15 Omega cm(2). Phase angles changed from 90 degrees for PES and PES-GO (capacitative behavior) to 0 degrees for all the RGO coated samples (resistive behavior). Electro-activity was measured by cyclic voltammetry (CV) and scanning electrochemical microscopy. An increase in electro-activity was observed when the inactive GO was reduced to RGO. With CV an increase of electro-activity was observed with an increasing number of RGO layers. The contact between the different RGO sheets is responsible for the electric conduction in the fabrics. The techniques used showed that with only one RGO coating, the contact between the RGO sheets is not good and more coatings were needed to assure good electrical and electrochemical properties. (C) 2013 Elsevier Ltd. All rights reserved., The authors wish to thank the Spanish Ministerio de Ciencia e Innovacion (contracts CTM2010-18842-C02-02 and CTM2011-23583) and Universitat Politecnica de Valencia (Vicerrectorado de Investigacion PAID-06-10 contract 003-233) for their financial support. J. Molina is grateful to the Conselleria d'Educacio, Formacio i Ocupacio (Generalitat Valenciana) for the Programa VALi+D post-doctoral fellowship. A.I. del Rio is grateful to the Spanish Ministerio de Ciencia y TecnologRia for the FPI fellowship.