Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

FIB in-situ fabrication of pseudo vertical diamond Schottky diode: H-terminated ohmic contact and O-terminated Schottky barrier

  • Valendolf Nunes, Jackeline
  • Leinen, D.
  • Alba Muñoz, Gonzalo
  • Lloret Vieira, Fernando Manuel
  • Piñero Charlo, José Carlos
  • Suzuki, Mariko
  • Araújo Gay, Daniel
Among diamond-based devices, the Schottky barrier diode (SBD) shows significant promise, achieving high breakdown voltages (9.5 MV⋅cm ) and reduced serial resistance (1 Ω) through structural advancements. The performance of SBDs depends on the interface between the Schottky contact, surface termination, and diamond. Studies have highlighted the impact of interface configuration on Schottky barrier height (SBH), particularly for hydrogen (H) and oxygen (O)-terminated diamonds. H-terminated surfaces exhibit negative electron affinity (NEA), whereas O-terminated surfaces show positive electron affinity (PEA). This surface behaviour has a strong impact on electron affinity, surface conductivity, work function, and the SBH which are critical for device performance. To know more about the metal-surface-diamond interface, tungsten (W) and platinum (Pt) deposited by electron beam-induced deposition (EBID), in a FIB dual beam, were employed as Schottky contacts on H and O-terminated diamond. The resulting structure has a pseudo vertical configuration with a back ohmic contact on a p ++ boron-doped layer. The current–voltage (I-V) and X-ray photoelectron spectroscopy (XPS) measurements resulted in a SBH of 1.69 eV for W and 1.76 eV for Pt, with an ideal factor (n) of 1.22 and 1.18, respectively. These n values demonstrated a chemical reactivity between metal-surface-diamond. Finally, a combination of two techniques for the SBH estimation is discussed.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

On the Piezoelectric Properties of Zinc Oxide Thin Films Synthesized by Plasma Assisted DC Sputter Deposition

  • McKinlay, Michael
  • Fleming, Lewis
  • Pelayo García, Manuel
  • Nieto Sierra, Lucía
  • Villar Castro, María del Pilar
  • Araújo Gay, Daniel
  • García, Basilio Javier
  • Gibson, Des
  • García Núñez, Carlos
This work presents a study of piezoelectric zinc oxide (ZnO) thin films deposited by a novel post-reactive sputtering method. The process utilizes a rotating drum with DC magnetron sputtering deposition onto substrates with subsequent DC plasma-assisted oxidation of the deposited metal to metal oxide. The paper analyzes the influence of plasmaassisted magnetron sputtering (PA-MS) deposition parameters (O2 plasma source power, O2 flow, and Ar flow) on the morphological, structural, optical, and piezoelectric properties of ZnO thin films. Design of experiments has been utilized to evaluate the role of these parameters on the growth rate (rg) and the properties of resulting films. Results indicate a predominant influence of the plasma power on the rg over other parameters. Among the eight tested samples, three of them show high crystal quality with high intensity (0001) diffraction peak, characteristic of the wurtzite crystalline structure of ZnO, and one of them exhibits piezoelectric coefficient values of ≈11pC N−1. That sample corresponding to a ZnO film deposited at the lowest rg of 0.075 nm s−1, confirmed the key role of the deposition parameters on the piezoelectric response of films, and demonstrated PA-MS as a promising technique to produce high-quality piezoelectric thin films.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Smart Cut Transfer of Wide-Bandgap Materials: The Case of Diamond

  • Widiez, Julie
  • Chrétien, Jérémie
  • Masante, Cédric
  • Gilles, Pierrick
  • Piñero Charlo, José Carlos
  • Milesi, Frédéric
  • Fernández de los Reyes, Daniel
  • Lloret Vieira, Fernando Manuel
  • Colonel, Lucas
  • Mazen, Frédéric
  • Araújo Gay, Daniel
  • Le Van Jodin, Lucie
Diamond exhibits a unique combination of exceptional properties, making it a highly attractive material for advanced technologies. Yet, these outstanding characteristics come at a cost: Diamond remains difficult to fabricate and is not readily available in large formats. In this context, the well-known Smart Cut layer transfer process—based on ion implantation and annealing—has been adapted for the first time to diamond. Turning a limitation into an advantage, the metastable nature of diamond allows for reducing the thermal budget required for cleavage. By finely tuning the implantation conditions, a buried sp2-rich layer can be created to serve as a fracture plane. Using this method, we successfully transfer an ~800-nm-thick diamond film onto a silicon substrate via metal bonding. After plasma etching of the residual sp2-rich layer, the transferred diamond preserves good crystalline quality, as confirmed by transmission electronic microscopy (TEM), electron energy loss spectroscopy (EELS), nanobeam diffraction, and Raman spectroscopy. While some implantation-induced point defects remain, they may be mitigated by a post-transfer annealing step. These results show that Smart Cut can be extended to ultrahard and chemically inert materials like diamond. This opens new perspectives for cost-effective, epi-ready diamond substrates on engineered hosts, paving the way for future high-performance electronics and quantum technologies.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Microscopic evidence of carbide formation at the interface of tungsten-based ohmic contacts on diamond

  • Valendolf Nunes, Jackeline
  • Piñero Charlo, José Carlos
  • Alba Muñoz, Gonzalo
  • Lloret Vieira, Fernando Manuel
  • Fernández de los Reyes, Daniel
  • Araújo Gay, Daniel
The fabrication of ohmic contacts is a fundamental technological step toward the development and manufacture of reliable electronic devices. However, in the case of diamond-based devices, there is a lack of knowledge related to the formation of these types of contacts. While the role of interface carbide formation on refractory–metal/diamond contacts has been reported as a key mechanism for the thermal stabilization and optimization of ohmic behaviour; there is still a lack of knowledge, at the diamond/tungsten (W) interface, related to the structural and chemical characteristics versus electrical performance. To fulfil this lack, W onto boron-doped diamond contacts were fabricated on a p+diamond layer by Electron-Beam Induced Deposition and followed by an annealing process. Then, W-diamond contacts were chemically, electrically, and structurally characterized at room temperature before and after thermal treatment. Once annealed, the Transfer Length Method (TLM) analysis revealed ohmic behaviour with specific contact resistance of 2.74 ×10 4 Ω⋅cm2. Electron Energy Loss Spectroscopy in Scanning Transmission Electron Microscopy (STEM-EELS) revealed tungsten carbide (WC) formation at the interface after annealing. So, a relation between WC formation and ohmic contact characteristics is demonstrated.