Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analyzing TLS Scan Distribution and Point Density for the Estimation of Forest Stand Structural Parameters

  • Torralba, Jesús|||0000-0001-8644-8604
  • Carbonell-Rivera, Juan Pedro|||0000-0002-6724-6780
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
  • Crespo-Peremarch, Pablo|||0000-0003-2241-4493
[EN] In recent decades, the feasibility of using terrestrial laser scanning (TLS) in forest inventories was investigated as a replacement for time-consuming traditional field measurements. However, the optimal acquisition of point clouds requires the definition of the minimum point density, as well as the sensor positions within the plot. This paper analyzes the effect of (i) the number and distribution of scans, and (ii) the point density on the estimation of seven forest parameters: above-ground biomass, basal area, canopy base height, dominant height, stocking density, quadratic mean diameter, and stand density index. For this purpose, 31 combinations of TLS scan positions, from a single scan in the center of the plot to nine scans, were analyzed in 28 circular plots in a Mediterranean forest. Afterwards, multiple linear regression models using height metrics extracted from the TLS point clouds were generated for each combination. In order to study the influence of terrain slope on the estimation of forest parameters, the analysis was performed by using all the plots and by creating two categories of plots according to their terrain slope (slight or steep). Results indicate that the use of multiple scans improves the estimation of forest parameters compared to using a single one, although using more than three to five scans does not necessarily improves the accuracy. Moreover, it is also shown that lower accuracies are obtained in plots with steep slope. In addition, it was observed that each forest parameter has a strategic distribution depending on the field of view of the TLS. Regarding the point density analysis, the use of 1% to 0.1% (¿136 points·m¿2) of the initial point cloud density (¿37,240.86 points·m¿2) generates an R2adj difference of less than 0.01. These findings are useful for planning more efficient forest inventories, reducing acquisition and processing time as well as costs., This research has been funded by the project PID2020-117808RB-C21 MCIN/AEI/10.13039/501100011033 and by the grant PEJ2018-002924-A Fondo de Garantia Juvenil en I+D+i ESF Investing in your future.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Análisis de posiciones y densidades TLS (Terrestrial Laser Scanning) para optimizar la estimación de parámetros forestales, Analyzing the position and density distributions of the Terrestrial Laser Scanning (TLS) to retrieve forest parameters

  • Torralba, Jesús|||0000-0001-8644-8604
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
  • Carbonell-Rivera, Juan Pedro|||0000-0002-6724-6780
  • Crespo-Peremarch, Pablo|||0000-0003-2241-4493
[EN] In the last decades, the feasibility and efficiency of using TLS (Terrestrial Laser Scanning) in forest inventories have been studied. Data acquisition requires defining the scan locations to register the largest proportion of forest parameters in the plot. In this study, 31 location combinations of TLS scanners, from a single scan in the center of the plot to nine scans, were analyzed in 28 plots in a Mediterranean forest. Multiple linear regression models were generated to estimate mean height and aboveground biomass (AGB) from point cloud elevation metrics from each combination of scan locations. Additionally, the accuracy variation of the selected models by randomly reducing the point density was also analyzed. The analysis of the number of TLS scans shows that an increment in the number of scans does not necessarily mean an improvement in the statistical models for either variable. Results show for both variables that the influence of the point density on the accuracy of the regression model is significant when its value drops below one hundredth part of the initial point density, [ES] En las últimas décadas se ha investigado la viabilidad y eficiencia del uso del TLS (Terrestrial Laser Scanning) en la realización de inventarios forestales. La adquisición de las nubes de puntos en campo implica definir los puntos de ubicación del sensor para registrar la mayor proporción de parámetros forestales en la parcela. En este estudio se realizó un análisis de 31 combinaciones de posiciones de escaneo TLS, considerando desde un escaneo simple en el centro de la parcela hasta un escaneo múltiple de 9 escaneos en 28 parcelas de bosque Mediterráneo. Se generaron modelos de regresión lineal múltiple para la obtención de la altura dominante de la parcela y la biomasa aérea total, a partir de las métricas de distribución de alturas de las nubes de puntos en cada combinación. También se analizó la evolución de la precisión de los modelos seleccionados al reducir aleatoriamente la densidad de puntos. En el análisis del número de escaneos TLS se observa que el aumento del número de tomas no implica una mejora en los modelos para ninguna de las dos variables. Por otro lado, el estudio de la reducción de densidad de puntos muestra para ambas variables forestales que la precisión del modelo de regresión no comienza a decrecer significativamente hasta reducir la nube a una centésima parte de la densidad original de puntos.