Pasar al contenido principal

THE VARIABILITY CHALLENGE IN NANO-CMOS AND BEYOND-CMOS: NOVEL IC DESIGN PARADIGMS FOR MITIGATION AND EXPLOITATION (VIGILANT-UPC)

PID2019-103869RB-C33

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 54
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

BPF-Based Thermal Sensor Circuit for On-Chip Testing of RF Circuits

  • Altet, Josep
  • Barajas, Enrique
  • Mateo, Diego
  • Billong, Alexandre
  • Aragonés, Xavier
  • Perpiñà, X.
  • Reverter, Ferran
© 2021 by the authors., A new sensor topology meant to extract figures of merit of radio-frequency analog integrated circuits (RF-ICs) was experimentally validated. Implemented in a standard 0.35 μm complementary metal-oxide-semiconductor (CMOS) technology, it comprised two blocks: a single metal-oxide-semiconductor (MOS) transistor acting as temperature transducer, which was placed near the circuit to monitor, and an active band-pass filter amplifier. For validation purposes, the temperature sensor was integrated with a tuned radio-frequency power amplifier (420 MHz) and MOS transistors acting as controllable dissipating devices. First, using the MOS dissipating devices, the performance and limitations of the different blocks that constitute the temperature sensor were characterized. Second, by using the heterodyne technique (applying two nearby tones) to the power amplifier (PA) and connecting the sensor output voltage to a low-cost AC voltmeter, the PA’s output power and its central frequency were monitored. As a result, this topology resulted in a low-cost approach, with high linearity and sensitivity, for RF-IC testing and variability monitoring., This research was funded by Spanish AEI–Agencia Estatal de Investigación–grant number PID2019-103869RB-C33. (X.P.) has also received founds from the Spanish Ministry of Science, Innovation and Universities through Agencia Estatal de Investigación (AEI) (projects: HIPERCELLS, RTI2018-098392B-I00, and “Fiabilidad Inteligente”, PCI2020-112028)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Circuit reliability prediction: Challenges and solutions for the device time-dependent variability characterization roadblock

  • Nafria, M.
  • Díaz-Fortuny, Javier
  • Saraza-Canflanca, P.
  • Martín-Martínez, Javier
  • Roca, Elisenda
  • Castro-López, Rafael
  • Rodríguez, Rosana
  • Martín-Lloret, P.
  • Toro-Frias, A.
  • Mateo, D.
  • Barajas, Enrique
  • Aragones, X.
  • Fernández, Francisco V.
Copyright IEEE, The characterization of the MOSFET Time-Dependent Variability (TDV) can be a showstopper for reliability-Aware circuit design in advanced CMOS nodes. In this work, a complete MOSFET characterization flow is presented, in the context of a physics-based TDV compact model, that addresses the main TDV characterization challenges for accurate circuit reliability prediction at design time. The pillars of this approach are described and illustrated through examples., This work was supported by the VIGILANT Project (PID2019-103869RB / AEI / 10.13039/501100011033) and the TEC2016-75151-C3-R Project (AEI/FEDER, UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

True Random Number Generator Based on RRAM-Bias Current Starved Ring Oscillator

  • Arumi, Daniel
  • Manich, S.
  • Gomez-Pau, Álvaro
  • Rodriguez-Montanes, Rosa
  • Bargallo, Mireia G.
  • Campabadal, Francesca
This work presents a resistive random access memory (RRAM)-bias current-starved ring oscillator (CSRO) as true random number generator (TRNG), where the cycle-to-cycle variability of an RRAM device is exploited as source of randomness. A simple voltage divider composed of this RRAM and a resistor is considered to bias the gate terminal of the extra transistor of every current starved (CS) inverter of the ring oscillator (RO). In this way, the delay of the inverters is modified, deriving an unpredictable oscillation frequency every time the RRAM switches to the high resistance state (HRS). The oscillation frequency is finally leveraged to extract the sequence of random bits. The design is simple and adds low area overhead. Experimental measurements are performed to analyze the cycle-to-cycle variability in the HRS. The very same measurements are subsequently used to validate the TRNG by means of electrical simulations. The obtained results passed all the National Institute of Standards and Technology randomness tests (NIST) tests without the need for postprocessing., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

True Random Number Generator Based on the Variability of the High Resistance State of RRAMs

  • Akbari, Maryam
  • Mirzakuchaki, Sattar
  • Arumí, Daniel
  • Manich, Salvador
  • Gómez-Pau, Alvaro
  • Campabadal, Francesca
  • González, Mireia Bargalló
  • Rodríguez-Montañés, Rosa
Hardware-based security primitives like True Random Number Generators (TRNG) have become a crucial part in protecting data over communication channels. With the growth of internet and cloud storage, TRNGs are required in numerous cryptographic operations. On the other hand, the inherently dense structure and low power characteristics of emerging nanoelectronic technologies such as resistive-switching memories (RRAM) make them suitable elements in designing hardware security modules integrated in CMOS ICs. In this paper, a memristor based TRNG is presented by leveraging the high stochasticity of RRAM resistance value in OFF (High Resistive) state. In the proposal, one or two devices can be used depending on whether the objective is focused on saving area or obtaining a higher random bit frequency generation. The generated bits, based on a combination of experimental measurements and SPICE simulations, passed all 15 National Institute of Standards and Technology (NIST) tests and achieved a throughput of tens of MHz., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Estudio, informe, memoria (Report)

Using temperature measurements to enhance security in front of hardware trojans, Emprant mesures de temperatura per millorar seguretat davant trojans implmenentats amb hardware

  • Altet Sanahujes, Josep|||0000-0002-6939-6475
  • Mateo Peña, Diego|||0000-0001-5996-9092
  • Barajas Ojeda, Enrique|||0000-0002-2072-2268
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
The goal of this document is to present a review of the work performed to carry out the task 3.5 of the Spanish National Project PID2019-103869RB-C33, entitled “El Reto de la Variabilidad en NANO-CMOS y BEYOND-CMOS: Nuevos Paradigmas de Diseño de Circuitos Integrados Para su Mitigación y Explotación (VIGILANT-UPC)”, whose principal investigator is Prof. Antonio Rubio. This document also resumes the deliverables of the task 3.5, which are: D2.3a: Report of the integrated circuit used in the experimentation D.2.3b: Report on the experimental characterization of the sensor. D.2.3c: Report of the procedure to extract golden signatures from sensor measurements. D.2.3d: Report of the self-healing procedure developed. D2.3e: Report of the IC measurements. D2.3f: Report on the reliability-aware BIST and machine learning techniques for monitoring of TDV., The goal of this document is to present a review of the work performed to carry out the task 3.5 of the Spanish National Project PID2019-103869RB-C33, entitled “El Reto de la Variabilidad en NANO-CMOS y BEYOND-CMOS: Nuevos Paradigmas de Diseño de Circuitos Integrados Para su Mitigación y Explotación (VIGILANT-UPC)”, whose principal investigator is Prof. Antonio Rubio. This document also resumes the deliverables of the task 3.5, which are: D2.3a: Report of the integrated circuit used in the experimentation D.2.3b: Report on the experimental characterization of the sensor. D.2.3c: Report of the procedure to extract golden signatures from sensor measurements. D.2.3d: Report of the self-healing procedure developed. D2.3e: Report of the IC measurements. D2.3f: Report on the reliability-aware BIST and machine learning techniques for monitoring of TDV.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Stochastic resonance exploration in current-driven ReRAM devices

  • Cirera Hernandez, Albert
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Pérez Leiva, Marcelo Alejandro
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Advances in emerging resistive random-access memory (ReRAM) technology show promise for its use in future computing systems, enabling neuromorphic and memory-centric computing architectures. However, one aspect that holds back the widespread practical use of ReRAM is the behavioral variability of resistive switching devices. In this context, a radically new path towards ReRAM-based electronics concerns the exploitation of noise and the Stochastic Resonance (SR) phenomenon as a mechanism to mitigate the impact of variability. While SR has been already demonstrated in ReRAM devices and its potential impact has been analyzed for memory applications, related works have only focused on voltage input signals. In this work we present preliminary results concerning the exploration of SR in current-driven ReRAM devices, commercially available by Knowm Inc. Our results indicate that additive noise of amplitude s = 0.125uA can stabilize the cycling performance of the devices, whereas higher noise amplitude improves the HRS-LRS resistance window, thus could affect positively the Bit Error Rate (BER) metric in ReRAM memory applications., Supported by the Chilean research grants FONDECYT INICIACION 11180706 and ANID-Basal FB0008, and by the Spanish MCIN grants PID2019-105658RB-I00, and MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Two examples of approximate arithmetic to reduce hardware complexity and power consumption

  • Fornt Mas, Jordi
  • Jin, Leixin
  • Etxezarreta, Imanol
  • Fontova, Pau
  • Altet Sanahujes, Josep|||0000-0002-6939-6475
  • Calomarde Palomino, Antonio|||0000-0002-4459-8505
  • Morancho Llena, Enrique|||0000-0003-2403-8145
  • Moll Echeto, Francisco de Borja|||0000-0002-1290-3253
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., As the end of Moore's Law approaches, electronic system designers must find ways to keep up with the ever increasing computational demands of the modern era. Some computationally intensive applications, such as multimedia processing, computer vision and artificial intelligence, present a unique feature that makes them especially suitable for hardware-level optimizations: their inherent robustness to noise and errors. This allows circuit designers to relax the constraint that arithmetic operations, such as multiplications and additions, must be completely accurate. Instead, approximations can be used in the arithmetic units, enabling system-level reductions in hardware area and power consumption, as well as improvements in performance, while hardly affecting the output of the final application. In this work, we explore two approximate arithmetic techniques. First, we consider approximations at the circuit design level by implementing several approximate multiplier units and evaluating their accuracy when used in executing YOLOv3, a state-of-the-art camera-based object detection deep neural network. Second, we apply the technique of overscaling to induce approximations in adder circuits by aggressively undervoltaging and overclocking them, and we compare the behavior of exact and approximate adders under these conditions. We find that, on one hand, some approximate multipliers are able to execute the YOLO network with almost no effect on the results, and on the other, approximate adder circuits are much more resilient to overscaling techniques than exact adders., This work was partially supported by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Stochastic resonance effect in binary STDP performed by RRAM devices

  • Salvador Aguilera, Emili
  • Rodríguez Martínez, Rosana
  • Martin Martínez, Javier
  • Crespo Yepes, Albert
  • Miranda Castellano, Enrique Alberto
  • Nafría Maqueda, Montserrat|||0000-0002-9549-2890
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Ntinas, Vasileios|||0000-0002-2367-5567
  • Sirakoulis, Georgios Ch.
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The beneficial role of noise in the binary spike time dependent plasticity (STDP) learning rule, when implemented with memristors, is experimentally analyzed. The two memristor conductance states, which emulate the neuron synapse in neuromorphic architectures, can be better distinguished if a gaussian noise is added to the bias. The addition of noise allows to reach memristor conductances which are proportional to the overlap between pre- and post-synaptic pulses., This research was funded by the Spanish MCIN/AEI/10.13039/501100011033, Projects PID2019- 103869RB and TEC2017-90969-EXP. The Spanish MicroNanoFab ICTS is acknowledged for sample fabrication., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Circuit topology and synthesis flow co-design for the development of computational ReRAM

  • Fernandez Hernandez, Carlos
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Emerging memory technologies will play a decisive role in the quest for more energy-efficient computing systems. Computational ReRAM structures based on resistive switching devices (memristors) have been explored for in-memory computations using the resistance of ReRAM cells for storage and for logic I/O representation. Such approach presents three major challenges: the support for a memristor-oriented logic style, the ad-hoc design of memory array driving circuitry for memory and logic operations, and the development of dedicated synthesis tools to instruct the multi-level operations required for the execution of an arbitrary logic function in memory. This work contributes towards the development of an automated design flow for ReRAM-based computational memories, highlighting some important HW-SW co-design considerations. We briefly present a case study concerning a synthesis flow for a nonstateful logic style and the co-design of the underlying 1T1R crossbar array driving circuit. The prototype of the synthesis flow is based on the ABC tool and the Z3 solver. It executes fast owing to the level-by-level mapping of logic gates. Moreover, it delivers a mapping that minimizes the logic function latency through parallel logic operations, while also using the less possible ReRAM cells., Supported by Synopsys, Chile, by the Chilean grants FONDECYT Regular 1221747 and ANID-Basal FB0008, and by the Spanish MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Toward designing high-speed cost-efficient quantum reversible carry select adders

  • Moghimi, Shekoofeh
  • Reza Reshadinezhad, Mohammad
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Compared to classical computing implementations, reversible arithmetic adders offer a valuable platform for implementing quantum computation models in digital systems and specific applications, such as cryptography and natural language processing. Reversible logic efficiently prevents energy wastage through thermal dissipation. This study presents a comprehensive exploration introducing new carry-select adders (CSLA) based on quantum and reversible logic. Five reversible CSLA designs are proposed and compared, evaluating various criteria, including speed, quantum cost, and area, compared to previously published schemes. These comparative metrics are formulated for arbitrary n-bit size blocks. Each design type is described generically, capable of implementing carry-select adders of any size. As the best outcome, this study proposes an optimized reversible adder circuit that addresses quantum propagation delay, achieving an acceptable trade-off with quantum cost compared to its counterparts. This article reduces calculation delay by 66%, 73%, 82%, and 87% for 16, 32, 64, and 128 bits, respectively, while maintaining a lower quantum cost in all cases., This research was supported in part by the Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

CMOS inverter performance degradation and its correlation with BTI, HCI and OFF state MOSFETs aging

  • Crespo Yepes, Albert
  • Nasarre Campo, Carles
  • Garsot Borras, Norbert
  • Martin Martínez, Javier
  • Rodríguez Martínez, Rosana
  • Barajas Ojeda, Enrique|||0000-0002-2072-2268
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
  • Mateo Peña, Diego|||0000-0001-5996-9092
  • Nafría Maqueda, Montserrat|||0000-0002-9549-2890
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In this work, CMOS inverters are subjected to electrical stress emulating a complete operation cycle and the shifts in the performance parameters (i.e., peak current and inversion voltage) evaluated. Moreover, degradation of the two MOSFETs is also measured as variations of their threshold voltage and mobility. The relationships between the observed transistors and circuit parameter shifts are explained in terms of the different device aging mechanisms (i.e., BTI, CHI and OFF-state) that are active depending on the voltages at the circuit terminals. Moreover, the combined effects of the aging mechanisms that are sequentially activated, at device and circuit levels, and their voltage dependence, are also discussed. Finally, a power law fitting of the inversion voltage degradation of the inverter is used to evaluate its variation at operating conditions., This work was supported in part by the VIGILANT Project (PID2019-103869RB / AEI / 10.13039/501100011033)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

True random number generator based on the variability of the high resistance state of RRAMs

  • Akbari, Maryam
  • Mirzakuchaki, Sattar
  • Arumi Delgado, Daniel|||0000-0002-6638-7485
  • Manich Bou, Salvador|||0000-0001-5265-1209
  • Gómez Pau, Álvaro|||0000-0002-7774-1662
  • Campabadal, Francesca
  • Bargalló González, Mireia
  • Rodríguez Montañés, Rosa|||0000-0001-6231-0862
Hardware-based security primitives like True Random Number Generators (TRNG) have become a crucial part in protecting data over communication channels. With the growth of internet and cloud storage, TRNGs are required in numerous cryptographic operations. On the other hand, the inherently dense structure and low power characteristics of emerging nanoelectronic technologies such as resistive-switching memories (RRAM) make them suitable elements in designing hardware security modules integrated in CMOS ICs. In this paper, a memristor based TRNG is presented by leveraging the high stochasticity of RRAM resistance value in OFF (High Resistive) state. In the proposal, one or two devices can be used depending on whether the objective is focused on saving area or obtaining a higher random bit frequency generation. The generated bits, based on a combination of experimental measurements and SPICE simulations, passed all 15 National Institute of Standards and Technology (NIST) tests and achieved a throughput of tens of MHz.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Influence of punch trough stop layer and well depths on the robustness of bulk FinFETs to heavy ions impact

  • Calomarde Palomino, Antonio|||0000-0002-4459-8505
  • Manich Bou, Salvador|||0000-0001-5265-1209
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Gamiz, Francisco
This study analyzes the effects of the punch-through stop (PTS) layer and well depth in a bulk FinFET SRAM cell on the fraction of charge generated by an ion impact that is collected by the FinFET channel. More than 1700 3D TCAD simulations have been performed to obtain a detailed map of the sensitivity areas in a full cell 6-T SRAM 22 nm bulk-FinFET process. The influence of the well depth on the charge collected by the drain devices of the SRAM cell has been studied, and it has been concluded that the collected charge can be reduced down to 300% simply by modifying the depth of the well, without affecting the performance of the cell. Different PTS layer depths have been analyzed in order to calculate which value minimizes the impact of the charge generated by an ion during its track along the FinFET body. The simulations carried out allow to conclude that the incorporation of a PTS layer not only reduces the leakage current, but also reduces the amount of charge, delivered by the ion, that reaches the drain region. Simulation results also show that the fraction of the charge generated by the ion impact, which is collected by the drain, mainly depends on the depth of the wells, whereas the PTS layer hardly modifies the collected charge., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Probabilistic resistive switching device modeling based on Markov jump processes

  • Ntinas, Vasileios|||0000-0002-2367-5567
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Sirakoulis, Georgios
In this work, a versatile mathematical framework for multi-state probabilistic modeling of Resistive Switching (RS) devices is proposed for the first time. The mathematical formulation of memristor and Markov jump processes are combined and, by using the notion of master equations for finite-states, the inherent probabilistic time-evolution of RS devices is sufficiently modeled. In particular, the methodology is generic enough and can be applied for N states; as a proof of concept, the proposed framework is further stressed for both a two-state RS paradigm, namely N=2, and a multi-state device, namely N=4. The presented I-V results demonstrate in a qualitative and quantitative manner, adequate matching with other modeling approaches., The research work was supported by the Hellenic Foundation for Research and Innovation (H.F.R.I.) under the First Call for H.F.R.I. Research Projects to support Faculty members and Researchers and the procurement of high-cost research equipment grant (Project Number: 3830)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

An ultra low-voltage RF front-end receiver for IoT devices

  • Malena, Francesco
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
  • Mateo Peña, Diego|||0000-0001-5996-9092
  • Caselli, Michele
  • Boni, Andrea
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents the design of an RF receiver front-end for IoT application, integrating a low noise amplifier (LNA) and an active mixer. The circuit is designed in 28-nm FDSOI technology, to operate on the ISM 2.4-2.5 GHz band. The inductor-less LNA exploits the parasitic package inductance as resonant load, limiting chip area and costs. The receiver, designed for the stringent requirements of the application, operates with a voltage supply of 0.35 V, and it exhibits in simulation a power consumption below 45 µW. Besides, it achieves a voltage gain of 27.4 dB, a Third Order Input Intercept Point (IIP3) of-26.8dBm, and a noise Figure (NF) of 12.8 dB, with an intermediate frequency (FI) of 2 MHz. The small area of only 0.0021 mm2, combined with the low power consumption and operating voltage, makes the proposed RF receiver well-suited for the IoT application domain., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Power-efficient noise-Induced reduction of ReRAM cell’s temporal variability effects

  • Ntinas, Vasileios|||0000-0002-2367-5567
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Sirakoulis, Georgios
  • Salvador, Emili
  • Pedro, Marta
  • Crespo-Yepes, A.
  • Martin Martinez, Javier
  • Rodríguez Martínez, Rosana
  • Nafría Maqueda, Montserrat|||0000-0002-9549-2890
Resistive Random Access Memory (ReRAM) is apromising novel memory technology for non-volatile storing, with low-power operation and ultra-high area density. However, ReRAM memories still face issues through commercialization, mainly owing to the fact that the high fabrication variations and the stochastic switching of the manufactured ReRAM devices cause high Bit Error Rate (BER). Given that ReRAM devices are nonlinear elements, the nonlinear phenomenon of Stochastic Resonance (SR), which defines that an input disturbance with specific characteristics can improve the total performance of the nonlinear system, is used to reduce the ReRAM cell’s BER. Thus, in this work, the BER of a single ReRAM cell is explored, using the Stanford PKU model, and is improved after the application of specific additive input noise. The power dissipation of the proposed approach is also evaluated and compared with the consideration of higher amplitude writing pulses in the lack of noise, showing that the proposed noiseinduced technique can decrease the BER without the excessive increase of the power dissipation. As a first step, towards the experimental verification of the proposed method, noise-induced measurements on a single fabricated ReRAM device are also performed. Overall, the presented results of the BER reduction with low power dissipation, reaching up to 3:26x less power consumption considering 100 ns writing pulses, are encouraging for ReRAM designers, delivering a circuit-level solution against the device-level problem., This work was supported in part by Spanish MICIU and MINECO under Projects TEC2016-75151-C3-R, TEC2017-90969-EXP and PID2019-103869RB-C3 and in part by FPI-UPC and partially supported by Greece-Russia bilateral joint research project MEM-Q (proj.no./MIS T4∆PΩ-00030/5021467) supported by GSRT, funded by National and European funds., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A reprogrammable graphene nanoribbon-based logic gate

  • Rallis, Konstantinos|||0000-0003-0501-5554
  • Fyrigos, Iosif-Angelos
  • Dimitrakis, Panagiotis
  • Dimitrakopoulos, George N.
  • Karafyllidis, Ioannis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this article, taking into consideration the exceptional technological properties of a unique 2-D material, namely Graphene, we are envisioning its usage as the structure material of a non-back-gated re-programmable switching device. The proposed topology is analyzed in depth, not only by verifying its operation and re-programmability as a 2-input XOR , 3-input XOR and 3-input Majority gate, but also by examining its computing performance in terms of area, delay and power dissipation. More specifically, we are utilizing L-shaped Graphene Nanoribbons (GNRs) to develop comb-shaped Graphene based switching devices. These devices are in position with effective programming through biasing to design any combinatorial circuit as resulting from the aforementioned universal set of Boolean gates. The resulting figures of merit regarding the area with a universal footprint of 2.53 nm2 for every gate independently of the number of inputs, the propagation delay with 2.05×10-2ps and, last but not least, the power dissipation with only 10.204 nW for the gates with greater number of inputs, are quite encouraging and promising. Moreover, the ability of the proposed topology to pave the way towards the implementation of basic circuits has been further investigated, by demonstrating an example of a 1-bit full adder cell and its sufficient operation arriving from the corresponding successful SPICE simulation results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Alternative memristor-based interconnect topologies for fast adaptive synchronization of chaotic circuits

  • Escudero López, Manuel
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
© 2020 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Resistive switching devices (memristors) constitute an emerging device technology promising for a vari- ety of applications that are currently being studied. In this context, the use of memristors as coupling el- ements of the dynamics of chaotic circuits for adaptive synchronization purposes, was recently proposed and the passive crossbar array was evaluated as target interconnect medium. Nonetheless, memristors may suffer from defects and degradation. Therefore, this work evaluates the impact of memristor switch- ing faults in an adaptive chaotic synchronization scheme, exploring at the same time the fault-tolerance of the crossbar architecture. Moreover, inspired from our observations in the stuck-at-OFF fault analy- sis of the memristive crossbar, some alternative scalable memristive interconnect patterns are suggested, whose performance is found independent of the number of interconnected chaotic circuits, requiring a much smaller number of total memristors than the crossbar array. All simulations are based on an ac- curate physics-based model of a bipolar memristor with filamentary switching mechanism. Based on our results, using the alternative topologies instead of the crossbar array leads to significant savings in the synchronization time that increase with the number of interconnected chaotic units, at the cost of more limited scaling capability and fault-tolerance., This work was supported in part by the Chilean research Grants ANID REDES ETAPA INICIAL 2017 No. REDI170604, ANID FONDECYT INICIACION 11180706, ANID BASAL FB0008, and by the Spanish MINECO and ERDF under Grant TEC2016-75151-C3-2-R., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the fitting and improvement of RRAM stanford-based model parameters using TiN/Ti/HfO2/W experimental data

  • Mahboubi, Vahab|||0000-0001-7859-4230
  • Arumi Delgado, Daniel|||0000-0002-6638-7485
  • Gómez Pau, Álvaro|||0000-0002-7774-1662
  • Rodríguez Montañés, Rosa|||0000-0001-6231-0862
  • Manich Bou, Salvador|||0000-0001-5265-1209
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The use of Resistive Random Access Memory (RRAM) devices is becoming pervasive in many applications. In particular, security based primitives can exploit their variability and non-volatility for generating cells for Non-Volatile Secure Memory (NVSM) and Physically Unclonable Function (PUF). Stanford-PKU Resistive Random Access Memory (RRAM) model is a successful model that has been used for simulating different types of RRAM-based systems. However, some circuit-related problems appear when more than one device are coupled together. In this paper, a parameter fitting is performed for a real TiN/Ti/HfO 2 /W RRAMs and the statistical characteristics of the variability in the experimental data are analyzed and included in order to obtain a more reliable model for simulations., This work was supported in part by the Spanish Ministry of Science, Innovation and Universities under Grant PID2019-103869RB-C33/ AEI /10.13039/501100011033, and through FEDER funds under Grant TEC2017- 84321-C4-1-R., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Novel circuit design methodology with graphene nanoribbon based devices

  • Rallis, Konstantinos|||0000-0003-0501-5554
  • Dimitrakopoulos, Giorgos
  • Dimitrakis, Panagiotis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Cotofana, Sorin
  • Karafyllidis, Ioannis
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Graphene has attracted a high amount of interest in recent years in many research fields, including the field of electronics. Due to its spectacular properties, it is investigated as a candidate material for the realization of nanodevices that will constitute conventional or even unconventional computing circuits. In this work, we explore the ability of Graphene Nanoribbon based topologies to create a universal computing set. We propose the design of an AND, OR and NOT gate, as well as the design of a Buffer, for the first time in a configuration similar to the Pass Transistor Logic (PTL) configuration. The valid operation of the proposed topologies is verified through accurate SPICE simulations, providing the ability to design combinational logic using Graphene, based on PTL methodology., This research was supported in part by the Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33 and grant 391 (with the support of the Secretaria d’Universitats i Recerca del Departament d’Empresa i Coneixement de la Generalitat de Catalunya), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

MemCA: all-memristor design for deterministic and probabilistic cellular automata hardware realization

  • Ntinas, Vasileios|||0000-0002-2367-5567
  • Fyrigos, Iosif-Angelos
  • Karamani, Rafallia
  • Vasileiadis, Nikolaos
  • Dimitrakis, Panagiotis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, Inspired by the behavior of natural systems, Cellular Automata (CA) tackle the demanding long-distance information transfer of conventional computers by the massive parallel computation performed by a set of locally-coupled dynamical nodes. Although CA are envisioned as powerful deterministic computers, their intrinsic capabilities are expanded after the memristor’s probabilistic switching is introduced into CA cells, resulting in new hybrid deterministic and probabilistic memristor-based CA (MemCA). In the proposed MemCA hardware realization, memristor devices are incorporated in both the cell and rule modules, composing the very first all-memristor CA hardware, designed with mixed CMOS/Memristor circuits. The proposed implementation accomplishes high operating speed and reduced area requirements, exploiting also memristor as an entropy source in every CA cell. MemCA’s functioning is showcased in deterministic and probabilistic operation, which can be externally modified by the selection of programming voltage amplitude, without changing the design. Also, the proposed MemCA system includes a reconfigurable rule module implementation that allows for spatial and temporal rule inhomogeneity., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Beneficial role of noise in Hf-based memristors

  • Rodriguez, Rosana
  • Martin Martinez, Javier
  • Salvador, Emili
  • Crespo Yepes, Albert
  • Miranda, Enrique Alberto
  • Nafria, Montserrat
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Ntinas, Vasileios|||0000-0002-2367-5567
  • Sirakoulis, Georgios Ch.
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The beneficial role of noise in the performance of Hf-based memristors has been experimentally studied. The addition of an external gaussian noise to the bias circuitry positively impacts the memristors characteristics by increasing the OFF/ON resistances ratio. The known stochastic resonance effect has been observed, when changing the standard deviation of the noise. The influence of the additive noise on the memristor current-voltage characteristic and on the set and reset related parameters are also presented., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB and TEC2017-90969-EXP., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

True random number generator based on RRAM-bias current starved ring oscillator

  • Arumi Delgado, Daniel|||0000-0002-6638-7485
  • Manich Bou, Salvador|||0000-0001-5265-1209
  • Gómez Pau, Álvaro|||0000-0002-7774-1662
  • Rodríguez Montañés, Rosa|||0000-0001-6231-0862
  • Bargalló González, Mireia
  • Campabadal, Francesca
This work presents a RRAM-bias current starved ring oscillator (CSRO) as TRNG, where the cycle-to-cycle variability of a RRAM device is exploited as source of randomness. A simple voltage divider composed of this RRAM and a resistor is considered to bias the gate terminal of the extra transistor of every current starved (CS) inverter of the RO. In this way, the delay of the inverters is modified, deriving an unpredictable oscillation frequency every time the RRAM switches to the HRS. The oscillation frequency is finally leveraged to extract the sequence of random bits. The design is simple and add low area overhead. Experimental measurements are performed to analyze the cycle-to-cycle variability in the HRS. The very same measurements are subsequently used to validate the TRNG by means of electrical simulations. The obtained results passed all the NIST tests without the need for post-processing., This work was supported by the Spanish MCIN/AEI/10.13039/501100011033 under Project PID2019-103869RB-C33. The work of M. B. González was supported by the Ramón y Cajal under Grant RYC2020-030150-I., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

High sensitivity temperature measurements to track and Ccompensate aging effects on CMOS amplifiers

  • Mateo Peña, Diego|||0000-0001-5996-9092
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
  • Barajas Ojeda, Enrique|||0000-0002-2072-2268
  • Altet Sanahujes, Josep|||0000-0002-6939-6475
This article presents a method to monitor and compensate gain degradation produced by aging in linear CMOS amplifiers. The proposed procedure relies on a stand-alone temperature sensor circuit. DC measurements at the output of the temperature sensor allow to monitor high-frequency gain, and to select an adaptive biasing to keep a constant gain along the circuit lifetime. The approach is validated experimentally on a high-frequency Power Amplifier, which was subjected to an accelerated aging degradation. Experimental results demonstrate the capability to keep the amplifier gain within 0.3 dB from its fresh value, even after important device aging degradation., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Using current to drive two SDC memristors connected in series and in anti-series

  • Cirera Hernandez, Albert
  • Garrido, Blas
  • Miribel, Pere
  • Colomer-Farrarons, Jordi
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
  • Vourkas, Ioannis
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Networks of bipolar memristors have a rich collective switching behavior, which can be exploited in computing applications. Such a small network is formed by a pair of bipolar memristors connected in a series or anti-series configuration. The latter is known as complementary resistive switch (CRS), and has been studied for memory and for logic applications. While CRS structures have been investigated with voltage-based driving schemes, the collective behavior of current-driven networks of memristors has not yet been explored. To this end, here we present preliminary experimental results from two bipolar self-directed channel (SDC) memristors by Knowm Inc., connected in series with the same or the opposite polarity, driven by current. The amplitude of the applied current pulses varied between |0.1 uA| and |1.0 uA|. The results demonstrate that current-based driving is effective for programming simultaneously memristors that are connected in series. Moreover, the devices in the CRS configuration respond in a complementary way to the applied input current. We observed a stable and uniform performance of the devices in all our experiments. Current pulses of |0.1 uA| did not affect the state of the memristors, so they can be used to perform READ operations in current-driven resistive memory modules., Funded in part by ANID (Chile) grants Basal FB0008 and FONDECYT No. 1221747; also by MICINN (Spain) Grants TED2021-129643B-I00 (FLEXRRAM Project) and PID2019-105658RB-I00 (PRITES Project), and by MCIN/AEI/10.13039/501100011033 Project PID2019-103869RB-C33, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

BPF-based thermal sensor circuit for on-chip testing of RF circuits

  • Altet Sanahujes, Josep|||0000-0002-6939-6475
  • Barajas Ojeda, Enrique|||0000-0002-2072-2268
  • Mateo Peña, Diego|||0000-0001-5996-9092
  • Billong, Alexandre
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
  • Perpiñà Gilabet, Xavier
  • Reverter Cubarsí, Ferran|||0000-0003-1653-0519
A new sensor topology meant to extract figures of merit of radio-frequency analog integrated circuits (RF-ICs) was experimentally validated. Implemented in a standard 0.35 µm complementary metal-oxide-semiconductor (CMOS) technology, it comprised two blocks: a single metaloxide-semiconductor (MOS) transistor acting as temperature transducer, which was placed near the circuit to monitor, and an active band-pass filter amplifier. For validation purposes, the temperature sensor was integrated with a tuned radio-frequency power amplifier (420 MHz) and MOS transistors acting as controllable dissipating devices. First, using the MOS dissipating devices, the performance and limitations of the different blocks that constitute the temperature sensor were characterized. Second, by using the heterodyne technique (applying two nearby tones) to the power amplifier (PA) and connecting the sensor output voltage to a low-cost AC voltmeter, the PA’s output power and its central frequency were monitored. As a result, this topology resulted in a low-cost approach, with high linearity and sensitivity, for RF-IC testing and variability monitoring., This research was funded by Spanish AEI–Agencia Estatal de Investigación–grant number PID2019-103869RB-C33. (X.P.) has also received founds from the Spanish Ministry of Science, Innovation and Universities through Agencia Estatal de Investigación (AEI) (projects: HIPERCELLS, RTI2018-098392B-I00, and “Fiabilidad Inteligente”, PCI2020-112028)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A circuit-level SPICE modeling strategy for the simulation of behavioral variability in ReRAM

  • Cayo, Jose
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio|||0000-0003-1625-1472
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The intrinsic behavioral variability in resistive switching devices (also known as 'memristors' or 'ReRAM devices') can be a reliability limiting factor or an opportunity for applications where randomness of resistance switching is essential, such as hardware security and stochastic computing. The realistic assessment of ReRAM-based circuits & systems towards practical exploitation requires variability-aware ReRAM modeling. In this context, here we present a versatile, circuit-level implementation strategy to incorporate cycle-to-cycle (C2C) variability to the ReRAM model parameters in SPICE simulations. We evaluated the proposed approach with threshold-based models of a voltage-controlled bipolar ReRAM device and managed to reproduce the main features observed in experimental curves for different pulsed voltage inputs. With key upgrades, compared to previous approaches found in the literature, our strategy enables the enhancement of any ReRAM device model towards the exploration of new ways to make the most of the C2C ReRAM variability, and to test the robustness of any designed circuits & systems against ReRAM variability., Supported by the Chilean research grants ANID-Basal FB0008 and FONDECYT Regular 1221747, and by the Spanish MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Aging compensation in a class-A high-frequency amplifier with DC temperature measurements

  • Altet Sanahujes, Josep|||0000-0002-6939-6475
  • Aragonès Cervera, Xavier|||0000-0003-1352-8675
  • Barajas Ojeda, Enrique|||0000-0002-2072-2268
  • Gisbert Beguer, Xavier
  • Martínez Domingo, Sergio
  • Mateo Peña, Diego|||0000-0001-5996-9092
One of the threats to nanometric CMOS analog circuit reliability is circuit performance degradation due to transistor aging. To extend circuit operating life, the bias of the main devices within the circuit must be adjusted while the aging degradation process affects them by using a monitor circuit that tracks the evolution of the circuit performance. In this paper, we propose the use of DC temperature measurements in the proximity of the circuit to perform the monitoring of circuit performance degradation and as an observable variable to adjust the bias of the main devices to restore the degraded performance to the original values. To this end, we present experimental results obtained from nine samples of a standard CMOS integrated circuit containing a high-frequency class-A power amplifier and a differential temperature sensor. After accelerated aging, the gain of the amplifier is degraded up to 50%. We propose two different procedures to perform DC temperature measurements that allow tracking of the amplifier gain degradation due to aging and, by uniquely observing temperature readings, automatically set a new bias for the amplifier devices that restores the original amplifier gain. Whereas one of the procedures is able to restore the gain up to a certain limit, the second allows full gain restoration., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A reprogrammable graphene nanoribbon-based logic gate

  • Rallis, Konstantinos
  • Fyrigos, Iosif-Angelos
  • Dimitrakis, Panagiotis
  • Dimitrakopoulos, George N.
  • Karafyllidis, Ioannis
  • Rubio Sola, Jose Antonio
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this article, taking into consideration the exceptional technological properties of a unique 2-D material, namely Graphene, we are envisioning its usage as the structure material of a non-back-gated re-programmable switching device. The proposed topology is analyzed in depth, not only by verifying its operation and re-programmability as a 2-input XOR , 3-input XOR and 3-input Majority gate, but also by examining its computing performance in terms of area, delay and power dissipation. More specifically, we are utilizing L-shaped Graphene Nanoribbons (GNRs) to develop comb-shaped Graphene based switching devices. These devices are in position with effective programming through biasing to design any combinatorial circuit as resulting from the aforementioned universal set of Boolean gates. The resulting figures of merit regarding the area with a universal footprint of 2.53 nm2 for every gate independently of the number of inputs, the propagation delay with 2.05×10-2ps and, last but not least, the power dissipation with only 10.204 nW for the gates with greater number of inputs, are quite encouraging and promising. Moreover, the ability of the proposed topology to pave the way towards the implementation of basic circuits has been further investigated, by demonstrating an example of a 1-bit full adder cell and its sufficient operation arriving from the corresponding successful SPICE simulation results., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

True random number generator based on the variability of the high resistance state of RRAMs

  • Akbari, Maryam
  • Mirzakuchaki, Sattar
  • Arumi Delgado, Daniel
  • Manich Bou, Salvador
  • Gómez Pau, Álvaro
  • Campabadal, Francesca
  • Bargalló González, Mireia
  • Rodríguez Montañés, Rosa
Hardware-based security primitives like True Random Number Generators (TRNG) have become a crucial part in protecting data over communication channels. With the growth of internet and cloud storage, TRNGs are required in numerous cryptographic operations. On the other hand, the inherently dense structure and low power characteristics of emerging nanoelectronic technologies such as resistive-switching memories (RRAM) make them suitable elements in designing hardware security modules integrated in CMOS ICs. In this paper, a memristor based TRNG is presented by leveraging the high stochasticity of RRAM resistance value in OFF (High Resistive) state. In the proposal, one or two devices can be used depending on whether the objective is focused on saving area or obtaining a higher random bit frequency generation. The generated bits, based on a combination of experimental measurements and SPICE simulations, passed all 15 National Institute of Standards and Technology (NIST) tests and achieved a throughput of tens of MHz., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

An ultra low-voltage RF front-end receiver for IoT devices

  • Malena, Francesco
  • Aragonès Cervera, Xavier
  • Mateo Peña, Diego
  • Caselli, Michele
  • Boni, Andrea
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents the design of an RF receiver front-end for IoT application, integrating a low noise amplifier (LNA) and an active mixer. The circuit is designed in 28-nm FDSOI technology, to operate on the ISM 2.4-2.5 GHz band. The inductor-less LNA exploits the parasitic package inductance as resonant load, limiting chip area and costs. The receiver, designed for the stringent requirements of the application, operates with a voltage supply of 0.35 V, and it exhibits in simulation a power consumption below 45 µW. Besides, it achieves a voltage gain of 27.4 dB, a Third Order Input Intercept Point (IIP3) of-26.8dBm, and a noise Figure (NF) of 12.8 dB, with an intermediate frequency (FI) of 2 MHz. The small area of only 0.0021 mm2, combined with the low power consumption and operating voltage, makes the proposed RF receiver well-suited for the IoT application domain., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

CMOS inverter performance degradation and its correlation with BTI, HCI and OFF state MOSFETs aging

  • Crespo Yepes, Albert
  • Nasarre Campo, Carles
  • Garsot Borras, Norbert
  • Martin Martínez, Javier
  • Rodríguez Martínez, Rosana
  • Barajas Ojeda, Enrique
  • Aragonès Cervera, Xavier
  • Mateo Peña, Diego
  • Nafría Maqueda, Montserrat
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In this work, CMOS inverters are subjected to electrical stress emulating a complete operation cycle and the shifts in the performance parameters (i.e., peak current and inversion voltage) evaluated. Moreover, degradation of the two MOSFETs is also measured as variations of their threshold voltage and mobility. The relationships between the observed transistors and circuit parameter shifts are explained in terms of the different device aging mechanisms (i.e., BTI, CHI and OFF-state) that are active depending on the voltages at the circuit terminals. Moreover, the combined effects of the aging mechanisms that are sequentially activated, at device and circuit levels, and their voltage dependence, are also discussed. Finally, a power law fitting of the inversion voltage degradation of the inverter is used to evaluate its variation at operating conditions., This work was supported in part by the VIGILANT Project (PID2019-103869RB / AEI / 10.13039/501100011033)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Probabilistic resistive switching device modeling based on Markov jump processes

  • Ntinas, Vasileios
  • Rubio Sola, Jose Antonio
  • Sirakoulis, Georgios
In this work, a versatile mathematical framework for multi-state probabilistic modeling of Resistive Switching (RS) devices is proposed for the first time. The mathematical formulation of memristor and Markov jump processes are combined and, by using the notion of master equations for finite-states, the inherent probabilistic time-evolution of RS devices is sufficiently modeled. In particular, the methodology is generic enough and can be applied for N states; as a proof of concept, the proposed framework is further stressed for both a two-state RS paradigm, namely N=2, and a multi-state device, namely N=4. The presented I-V results demonstrate in a qualitative and quantitative manner, adequate matching with other modeling approaches., The research work was supported by the Hellenic Foundation for Research and Innovation (H.F.R.I.) under the First Call for H.F.R.I. Research Projects to support Faculty members and Researchers and the procurement of high-cost research equipment grant (Project Number: 3830)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Aging compensation in a class-A high-frequency amplifier with DC temperature measurements

  • Altet Sanahujes, Josep
  • Aragonès Cervera, Xavier
  • Barajas Ojeda, Enrique
  • Gisbert Beguer, Xavier
  • Martínez Domingo, Sergio
  • Mateo Peña, Diego
One of the threats to nanometric CMOS analog circuit reliability is circuit performance degradation due to transistor aging. To extend circuit operating life, the bias of the main devices within the circuit must be adjusted while the aging degradation process affects them by using a monitor circuit that tracks the evolution of the circuit performance. In this paper, we propose the use of DC temperature measurements in the proximity of the circuit to perform the monitoring of circuit performance degradation and as an observable variable to adjust the bias of the main devices to restore the degraded performance to the original values. To this end, we present experimental results obtained from nine samples of a standard CMOS integrated circuit containing a high-frequency class-A power amplifier and a differential temperature sensor. After accelerated aging, the gain of the amplifier is degraded up to 50%. We propose two different procedures to perform DC temperature measurements that allow tracking of the amplifier gain degradation due to aging and, by uniquely observing temperature readings, automatically set a new bias for the amplifier devices that restores the original amplifier gain. Whereas one of the procedures is able to restore the gain up to a certain limit, the second allows full gain restoration., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Design and simulation of peripheral driving circuitry for computational ReRAM, Diseño y simulación de circuito periférico de actuación para ReRAM computacional

  • Fernández López, Cristina
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., As an alternative approach to the von Neumann architecture, the notion of computational resistive random- access memory (ReRAM) has emerged, promising faster and more energy-efficient computing systems. In this context, we present a classification of ReRAM-compatible logic design strategies and highlight the potential of nonstateful ratioed logic for computational ReRAM modules. We provide insights towards the design of ad-hoc peripheral circuitry that allows the fusion of memory and ratioed logic operations in the ReRAM module in a reliable manner; i.e., the driving/sensing circuitry allows carrying out memory operations and in-memory multi- level ratioed logic operations. To this end, we present in detail a computational ReRAM driver and focus our description on the operational features that enable memory/logic operations in every row of the crossbar array. We validate circuit functionality through LTSpice simulations for read/write memory and logic operations using a threshold-type bipolar ReRAM device model. The presented practical solutions contribute to the viable development of computational ReRAM., Supported by Synopsys, Chile, by the Chilean grants FONDECYT Regular 1221747 and ANID-Basal FB0008, by the UTFSM Initiation in Scientific Investigation Program (PIIC) grant 016/2021, and by the Spanish MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

BPF-based thermal sensor circuit for on-chip testing of RF circuits

  • Altet Sanahujes, Josep
  • Barajas Ojeda, Enrique
  • Mateo Peña, Diego
  • Billong, Alexandre
  • Aragonès Cervera, Xavier
  • Perpiñà Gilabet, Xavier
  • Reverter Cubarsí, Ferran
A new sensor topology meant to extract figures of merit of radio-frequency analog integrated circuits (RF-ICs) was experimentally validated. Implemented in a standard 0.35 µm complementary metal-oxide-semiconductor (CMOS) technology, it comprised two blocks: a single metaloxide-semiconductor (MOS) transistor acting as temperature transducer, which was placed near the circuit to monitor, and an active band-pass filter amplifier. For validation purposes, the temperature sensor was integrated with a tuned radio-frequency power amplifier (420 MHz) and MOS transistors acting as controllable dissipating devices. First, using the MOS dissipating devices, the performance and limitations of the different blocks that constitute the temperature sensor were characterized. Second, by using the heterodyne technique (applying two nearby tones) to the power amplifier (PA) and connecting the sensor output voltage to a low-cost AC voltmeter, the PA’s output power and its central frequency were monitored. As a result, this topology resulted in a low-cost approach, with high linearity and sensitivity, for RF-IC testing and variability monitoring., This research was funded by Spanish AEI–Agencia Estatal de Investigación–grant number PID2019-103869RB-C33. (X.P.) has also received founds from the Spanish Ministry of Science, Innovation and Universities through Agencia Estatal de Investigación (AEI) (projects: HIPERCELLS, RTI2018-098392B-I00, and “Fiabilidad Inteligente”, PCI2020-112028)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

High sensitivity temperature measurements to track and Ccompensate aging effects on CMOS amplifiers

  • Mateo Peña, Diego
  • Aragonès Cervera, Xavier
  • Barajas Ojeda, Enrique
  • Altet Sanahujes, Josep
This article presents a method to monitor and compensate gain degradation produced by aging in linear CMOS amplifiers. The proposed procedure relies on a stand-alone temperature sensor circuit. DC measurements at the output of the temperature sensor allow to monitor high-frequency gain, and to select an adaptive biasing to keep a constant gain along the circuit lifetime. The approach is validated experimentally on a high-frequency Power Amplifier, which was subjected to an accelerated aging degradation. Experimental results demonstrate the capability to keep the amplifier gain within 0.3 dB from its fresh value, even after important device aging degradation., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación

Using temperature measurements to enhance security in front of hardware trojans, Emprant mesures de temperatura per millorar seguretat davant trojans implmenentats amb hardware

  • Altet Sanahujes, Josep
  • Mateo Peña, Diego
  • Barajas Ojeda, Enrique
  • Aragonès Cervera, Xavier
The goal of this document is to present a review of the work performed to carry out the task 3.5 of the Spanish National Project PID2019-103869RB-C33, entitled “El Reto de la Variabilidad en NANO-CMOS y BEYOND-CMOS: Nuevos Paradigmas de Diseño de Circuitos Integrados Para su Mitigación y Explotación (VIGILANT-UPC)”, whose principal investigator is Prof. Antonio Rubio. This document also resumes the deliverables of the task 3.5, which are: D2.3a: Report of the integrated circuit used in the experimentation D.2.3b: Report on the experimental characterization of the sensor. D.2.3c: Report of the procedure to extract golden signatures from sensor measurements. D.2.3d: Report of the self-healing procedure developed. D2.3e: Report of the IC measurements. D2.3f: Report on the reliability-aware BIST and machine learning techniques for monitoring of TDV., The goal of this document is to present a review of the work performed to carry out the task 3.5 of the Spanish National Project PID2019-103869RB-C33, entitled “El Reto de la Variabilidad en NANO-CMOS y BEYOND-CMOS: Nuevos Paradigmas de Diseño de Circuitos Integrados Para su Mitigación y Explotación (VIGILANT-UPC)”, whose principal investigator is Prof. Antonio Rubio. This document also resumes the deliverables of the task 3.5, which are: D2.3a: Report of the integrated circuit used in the experimentation D.2.3b: Report on the experimental characterization of the sensor. D.2.3c: Report of the procedure to extract golden signatures from sensor measurements. D.2.3d: Report of the self-healing procedure developed. D2.3e: Report of the IC measurements. D2.3f: Report on the reliability-aware BIST and machine learning techniques for monitoring of TDV., Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Toward designing high-speed cost-efficient quantum reversible carry select adders

  • Moghimi, Shekoofeh
  • Reza Reshadinezhad, Mohammad
  • Rubio Sola, Jose Antonio
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Compared to classical computing implementations, reversible arithmetic adders offer a valuable platform for implementing quantum computation models in digital systems and specific applications, such as cryptography and natural language processing. Reversible logic efficiently prevents energy wastage through thermal dissipation. This study presents a comprehensive exploration introducing new carry-select adders (CSLA) based on quantum and reversible logic. Five reversible CSLA designs are proposed and compared, evaluating various criteria, including speed, quantum cost, and area, compared to previously published schemes. These comparative metrics are formulated for arbitrary n-bit size blocks. Each design type is described generically, capable of implementing carry-select adders of any size. As the best outcome, this study proposes an optimized reversible adder circuit that addresses quantum propagation delay, achieving an acceptable trade-off with quantum cost compared to its counterparts. This article reduces calculation delay by 66%, 73%, 82%, and 87% for 16, 32, 64, and 128 bits, respectively, while maintaining a lower quantum cost in all cases., This research was supported in part by the Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB-C33, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A circuit-level SPICE modeling strategy for the simulation of behavioral variability in ReRAM

  • Cayo, Jose
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The intrinsic behavioral variability in resistive switching devices (also known as 'memristors' or 'ReRAM devices') can be a reliability limiting factor or an opportunity for applications where randomness of resistance switching is essential, such as hardware security and stochastic computing. The realistic assessment of ReRAM-based circuits & systems towards practical exploitation requires variability-aware ReRAM modeling. In this context, here we present a versatile, circuit-level implementation strategy to incorporate cycle-to-cycle (C2C) variability to the ReRAM model parameters in SPICE simulations. We evaluated the proposed approach with threshold-based models of a voltage-controlled bipolar ReRAM device and managed to reproduce the main features observed in experimental curves for different pulsed voltage inputs. With key upgrades, compared to previous approaches found in the literature, our strategy enables the enhancement of any ReRAM device model towards the exploration of new ways to make the most of the C2C ReRAM variability, and to test the robustness of any designed circuits & systems against ReRAM variability., Supported by the Chilean research grants ANID-Basal FB0008 and FONDECYT Regular 1221747, and by the Spanish MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the fitting and improvement of RRAM stanford-based model parameters using TiN/Ti/HfO2/W experimental data

  • Mahboubi, Vahab
  • Arumi Delgado, Daniel
  • Gómez Pau, Álvaro
  • Rodríguez Montañés, Rosa
  • Manich Bou, Salvador
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The use of Resistive Random Access Memory (RRAM) devices is becoming pervasive in many applications. In particular, security based primitives can exploit their variability and non-volatility for generating cells for Non-Volatile Secure Memory (NVSM) and Physically Unclonable Function (PUF). Stanford-PKU Resistive Random Access Memory (RRAM) model is a successful model that has been used for simulating different types of RRAM-based systems. However, some circuit-related problems appear when more than one device are coupled together. In this paper, a parameter fitting is performed for a real TiN/Ti/HfO 2 /W RRAMs and the statistical characteristics of the variability in the experimental data are analyzed and included in order to obtain a more reliable model for simulations., This work was supported in part by the Spanish Ministry of Science, Innovation and Universities under Grant PID2019-103869RB-C33/ AEI /10.13039/501100011033, and through FEDER funds under Grant TEC2017- 84321-C4-1-R., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

MemCA: all-memristor design for deterministic and probabilistic cellular automata hardware realization

  • Ntinas, Vasileios
  • Fyrigos, Iosif-Angelos
  • Karamani, Rafallia
  • Vasileiadis, Nikolaos
  • Dimitrakis, Panagiotis
  • Rubio Sola, Jose Antonio
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, Inspired by the behavior of natural systems, Cellular Automata (CA) tackle the demanding long-distance information transfer of conventional computers by the massive parallel computation performed by a set of locally-coupled dynamical nodes. Although CA are envisioned as powerful deterministic computers, their intrinsic capabilities are expanded after the memristor’s probabilistic switching is introduced into CA cells, resulting in new hybrid deterministic and probabilistic memristor-based CA (MemCA). In the proposed MemCA hardware realization, memristor devices are incorporated in both the cell and rule modules, composing the very first all-memristor CA hardware, designed with mixed CMOS/Memristor circuits. The proposed implementation accomplishes high operating speed and reduced area requirements, exploiting also memristor as an entropy source in every CA cell. MemCA’s functioning is showcased in deterministic and probabilistic operation, which can be externally modified by the selection of programming voltage amplitude, without changing the design. Also, the proposed MemCA system includes a reconfigurable rule module implementation that allows for spatial and temporal rule inhomogeneity., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Circuit topology and synthesis flow co-design for the development of computational ReRAM

  • Fernandez Hernandez, Carlos
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Emerging memory technologies will play a decisive role in the quest for more energy-efficient computing systems. Computational ReRAM structures based on resistive switching devices (memristors) have been explored for in-memory computations using the resistance of ReRAM cells for storage and for logic I/O representation. Such approach presents three major challenges: the support for a memristor-oriented logic style, the ad-hoc design of memory array driving circuitry for memory and logic operations, and the development of dedicated synthesis tools to instruct the multi-level operations required for the execution of an arbitrary logic function in memory. This work contributes towards the development of an automated design flow for ReRAM-based computational memories, highlighting some important HW-SW co-design considerations. We briefly present a case study concerning a synthesis flow for a nonstateful logic style and the co-design of the underlying 1T1R crossbar array driving circuit. The prototype of the synthesis flow is based on the ABC tool and the Z3 solver. It executes fast owing to the level-by-level mapping of logic gates. Moreover, it delivers a mapping that minimizes the logic function latency through parallel logic operations, while also using the less possible ReRAM cells., Supported by Synopsys, Chile, by the Chilean grants FONDECYT Regular 1221747 and ANID-Basal FB0008, and by the Spanish MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Using current to drive two SDC memristors connected in series and in anti-series

  • Cirera Hernandez, Albert
  • Garrido, Blas
  • Miribel, Pere
  • Colomer-Farrarons, Jordi
  • Rubio Sola, Jose Antonio
  • Vourkas, Ioannis
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Networks of bipolar memristors have a rich collective switching behavior, which can be exploited in computing applications. Such a small network is formed by a pair of bipolar memristors connected in a series or anti-series configuration. The latter is known as complementary resistive switch (CRS), and has been studied for memory and for logic applications. While CRS structures have been investigated with voltage-based driving schemes, the collective behavior of current-driven networks of memristors has not yet been explored. To this end, here we present preliminary experimental results from two bipolar self-directed channel (SDC) memristors by Knowm Inc., connected in series with the same or the opposite polarity, driven by current. The amplitude of the applied current pulses varied between |0.1 uA| and |1.0 uA|. The results demonstrate that current-based driving is effective for programming simultaneously memristors that are connected in series. Moreover, the devices in the CRS configuration respond in a complementary way to the applied input current. We observed a stable and uniform performance of the devices in all our experiments. Current pulses of |0.1 uA| did not affect the state of the memristors, so they can be used to perform READ operations in current-driven resistive memory modules., Funded in part by ANID (Chile) grants Basal FB0008 and FONDECYT No. 1221747; also by MICINN (Spain) Grants TED2021-129643B-I00 (FLEXRRAM Project) and PID2019-105658RB-I00 (PRITES Project), and by MCIN/AEI/10.13039/501100011033 Project PID2019-103869RB-C33, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Stochastic resonance effect in binary STDP performed by RRAM devices

  • Salvador Aguilera, Emili
  • Rodríguez Martínez, Rosana
  • Martin Martínez, Javier
  • Crespo Yepes, Albert
  • Miranda Castellano, Enrique Alberto
  • Nafría Maqueda, Montserrat
  • Rubio Sola, Jose Antonio
  • Ntinas, Vasileios
  • Sirakoulis, Georgios Ch.
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The beneficial role of noise in the binary spike time dependent plasticity (STDP) learning rule, when implemented with memristors, is experimentally analyzed. The two memristor conductance states, which emulate the neuron synapse in neuromorphic architectures, can be better distinguished if a gaussian noise is added to the bias. The addition of noise allows to reach memristor conductances which are proportional to the overlap between pre- and post-synaptic pulses., This research was funded by the Spanish MCIN/AEI/10.13039/501100011033, Projects PID2019- 103869RB and TEC2017-90969-EXP. The Spanish MicroNanoFab ICTS is acknowledged for sample fabrication., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Power-efficient noise-Induced reduction of ReRAM cell’s temporal variability effects

  • Ntinas, Vasileios
  • Rubio Sola, Jose Antonio
  • Sirakoulis, Georgios
  • Salvador, Emili
  • Pedro, Marta
  • Crespo-Yepes, A.
  • Martin Martinez, Javier
  • Rodríguez Martínez, Rosana
  • Nafría Maqueda, Montserrat
Resistive Random Access Memory (ReRAM) is apromising novel memory technology for non-volatile storing, with low-power operation and ultra-high area density. However, ReRAM memories still face issues through commercialization, mainly owing to the fact that the high fabrication variations and the stochastic switching of the manufactured ReRAM devices cause high Bit Error Rate (BER). Given that ReRAM devices are nonlinear elements, the nonlinear phenomenon of Stochastic Resonance (SR), which defines that an input disturbance with specific characteristics can improve the total performance of the nonlinear system, is used to reduce the ReRAM cell’s BER. Thus, in this work, the BER of a single ReRAM cell is explored, using the Stanford PKU model, and is improved after the application of specific additive input noise. The power dissipation of the proposed approach is also evaluated and compared with the consideration of higher amplitude writing pulses in the lack of noise, showing that the proposed noiseinduced technique can decrease the BER without the excessive increase of the power dissipation. As a first step, towards the experimental verification of the proposed method, noise-induced measurements on a single fabricated ReRAM device are also performed. Overall, the presented results of the BER reduction with low power dissipation, reaching up to 3:26x less power consumption considering 100 ns writing pulses, are encouraging for ReRAM designers, delivering a circuit-level solution against the device-level problem., This work was supported in part by Spanish MICIU and MINECO under Projects TEC2016-75151-C3-R, TEC2017-90969-EXP and PID2019-103869RB-C3 and in part by FPI-UPC and partially supported by Greece-Russia bilateral joint research project MEM-Q (proj.no./MIS T4∆PΩ-00030/5021467) supported by GSRT, funded by National and European funds., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

True random number generator based on RRAM-bias current starved ring oscillator

  • Arumi Delgado, Daniel
  • Manich Bou, Salvador
  • Gómez Pau, Álvaro
  • Rodríguez Montañés, Rosa
  • Bargalló González, Mireia
  • Campabadal, Francesca
This work presents a RRAM-bias current starved ring oscillator (CSRO) as TRNG, where the cycle-to-cycle variability of a RRAM device is exploited as source of randomness. A simple voltage divider composed of this RRAM and a resistor is considered to bias the gate terminal of the extra transistor of every current starved (CS) inverter of the RO. In this way, the delay of the inverters is modified, deriving an unpredictable oscillation frequency every time the RRAM switches to the HRS. The oscillation frequency is finally leveraged to extract the sequence of random bits. The design is simple and add low area overhead. Experimental measurements are performed to analyze the cycle-to-cycle variability in the HRS. The very same measurements are subsequently used to validate the TRNG by means of electrical simulations. The obtained results passed all the NIST tests without the need for post-processing., This work was supported by the Spanish MCIN/AEI/10.13039/501100011033 under Project PID2019-103869RB-C33. The work of M. B. González was supported by the Ramón y Cajal under Grant RYC2020-030150-I., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Exploring different circuit-level approaches to the forming of resistive random access memories

  • Cirera, Albert
  • Fernandez, Carlos
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Advances in emerging resistive random-access memory (ReRAM) technology show promise to be used in future memory-centric computing systems. In ReRAM arrays that consist of two-terminal bipolar resistive switching (RS) devices, SET/RESET programming voltage pulses are used to switch them from low resistance state (LRS) to high resistance state (HRS). The recent commercialization of discrete and crossbar-array organized RS devices have certainly pushed forward experimentation with such emerging memory technology. One barrier still preventing their widespread practical use is the behavioral variability and the lack of a straightforward manner to implement the forming process and achieve uniform SET/RESET programing. In this paper, different circuit topologies and approaches are explored to perform the forming of the conductive channel in commercial discrete RS devices by Knowm Inc. A target-resistance is pursued through pulsed voltage stress, followed by cycle-to-cycle stabilization using a custom transimpedance amplifier circuit. Moreover, a voltage controlled low-current source is proposed as an approach to alleviate the complexity and risk of the forming process in device characterization., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Beneficial role of noise in Hf-based memristors

  • Rodriguez, Rosana
  • Martin Martinez, Javier
  • Salvador, Emili
  • Crespo Yepes, Albert
  • Miranda, Enrique Alberto
  • Nafria, Montserrat
  • Rubio Sola, Jose Antonio
  • Ntinas, Vasileios
  • Sirakoulis, Georgios Ch.
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The beneficial role of noise in the performance of Hf-based memristors has been experimentally studied. The addition of an external gaussian noise to the bias circuitry positively impacts the memristors characteristics by increasing the OFF/ON resistances ratio. The known stochastic resonance effect has been observed, when changing the standard deviation of the noise. The influence of the additive noise on the memristor current-voltage characteristic and on the set and reset related parameters are also presented., This research was funded by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019- 103869RB and TEC2017-90969-EXP., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Two examples of approximate arithmetic to reduce hardware complexity and power consumption

  • Fornt Mas, Jordi
  • Jin, Leixin
  • Etxezarreta, Imanol
  • Fontova, Pau
  • Altet Sanahujes, Josep
  • Calomarde Palomino, Antonio
  • Morancho Llena, Enrique
  • Moll Echeto, Francisco de Borja
  • Rubio Sola, Jose Antonio
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., As the end of Moore's Law approaches, electronic system designers must find ways to keep up with the ever increasing computational demands of the modern era. Some computationally intensive applications, such as multimedia processing, computer vision and artificial intelligence, present a unique feature that makes them especially suitable for hardware-level optimizations: their inherent robustness to noise and errors. This allows circuit designers to relax the constraint that arithmetic operations, such as multiplications and additions, must be completely accurate. Instead, approximations can be used in the arithmetic units, enabling system-level reductions in hardware area and power consumption, as well as improvements in performance, while hardly affecting the output of the final application. In this work, we explore two approximate arithmetic techniques. First, we consider approximations at the circuit design level by implementing several approximate multiplier units and evaluating their accuracy when used in executing YOLOv3, a state-of-the-art camera-based object detection deep neural network. Second, we apply the technique of overscaling to induce approximations in adder circuits by aggressively undervoltaging and overclocking them, and we compare the behavior of exact and approximate adders under these conditions. We find that, on one hand, some approximate multipliers are able to execute the YOLO network with almost no effect on the results, and on the other, approximate adder circuits are much more resilient to overscaling techniques than exact adders., This work was partially supported by Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of punch trough stop layer and well depths on the robustness of bulk FinFETs to heavy ions impact

  • Calomarde Palomino, Antonio
  • Manich Bou, Salvador
  • Rubio Sola, Jose Antonio
  • Gamiz, Francisco
This study analyzes the effects of the punch-through stop (PTS) layer and well depth in a bulk FinFET SRAM cell on the fraction of charge generated by an ion impact that is collected by the FinFET channel. More than 1700 3D TCAD simulations have been performed to obtain a detailed map of the sensitivity areas in a full cell 6-T SRAM 22 nm bulk-FinFET process. The influence of the well depth on the charge collected by the drain devices of the SRAM cell has been studied, and it has been concluded that the collected charge can be reduced down to 300% simply by modifying the depth of the well, without affecting the performance of the cell. Different PTS layer depths have been analyzed in order to calculate which value minimizes the impact of the charge generated by an ion during its track along the FinFET body. The simulations carried out allow to conclude that the incorporation of a PTS layer not only reduces the leakage current, but also reduces the amount of charge, delivered by the ion, that reaches the drain region. Simulation results also show that the fraction of the charge generated by the ion impact, which is collected by the drain, mainly depends on the depth of the wells, whereas the PTS layer hardly modifies the collected charge., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Alternative memristor-based interconnect topologies for fast adaptive synchronization of chaotic circuits

  • Escudero López, Manuel
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
© 2020 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Resistive switching devices (memristors) constitute an emerging device technology promising for a vari- ety of applications that are currently being studied. In this context, the use of memristors as coupling el- ements of the dynamics of chaotic circuits for adaptive synchronization purposes, was recently proposed and the passive crossbar array was evaluated as target interconnect medium. Nonetheless, memristors may suffer from defects and degradation. Therefore, this work evaluates the impact of memristor switch- ing faults in an adaptive chaotic synchronization scheme, exploring at the same time the fault-tolerance of the crossbar architecture. Moreover, inspired from our observations in the stuck-at-OFF fault analy- sis of the memristive crossbar, some alternative scalable memristive interconnect patterns are suggested, whose performance is found independent of the number of interconnected chaotic circuits, requiring a much smaller number of total memristors than the crossbar array. All simulations are based on an ac- curate physics-based model of a bipolar memristor with filamentary switching mechanism. Based on our results, using the alternative topologies instead of the crossbar array leads to significant savings in the synchronization time that increase with the number of interconnected chaotic units, at the cost of more limited scaling capability and fault-tolerance., This work was supported in part by the Chilean research Grants ANID REDES ETAPA INICIAL 2017 No. REDI170604, ANID FONDECYT INICIACION 11180706, ANID BASAL FB0008, and by the Spanish MINECO and ERDF under Grant TEC2016-75151-C3-2-R., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Novel circuit design methodology with graphene nanoribbon based devices

  • Rallis, Konstantinos
  • Dimitrakopoulos, Giorgos
  • Dimitrakis, Panagiotis
  • Rubio Sola, Jose Antonio
  • Cotofana, Sorin
  • Karafyllidis, Ioannis
  • Sirakoulis, Georgios Ch.
© 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Graphene has attracted a high amount of interest in recent years in many research fields, including the field of electronics. Due to its spectacular properties, it is investigated as a candidate material for the realization of nanodevices that will constitute conventional or even unconventional computing circuits. In this work, we explore the ability of Graphene Nanoribbon based topologies to create a universal computing set. We propose the design of an AND, OR and NOT gate, as well as the design of a Buffer, for the first time in a configuration similar to the Pass Transistor Logic (PTL) configuration. The valid operation of the proposed topologies is verified through accurate SPICE simulations, providing the ability to design combinational logic using Graphene, based on PTL methodology., This research was supported in part by the Spanish MCIN/AEI/10.13039/501100011033, Project PID2019-103869RB-C33 and grant 391 (with the support of the Secretaria d’Universitats i Recerca del Departament d’Empresa i Coneixement de la Generalitat de Catalunya), Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Stochastic resonance exploration in current-driven ReRAM devices

  • Cirera Hernandez, Albert
  • Vourkas, Ioannis
  • Rubio Sola, Jose Antonio
  • Pérez Leiva, Marcelo Alejandro
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Advances in emerging resistive random-access memory (ReRAM) technology show promise for its use in future computing systems, enabling neuromorphic and memory-centric computing architectures. However, one aspect that holds back the widespread practical use of ReRAM is the behavioral variability of resistive switching devices. In this context, a radically new path towards ReRAM-based electronics concerns the exploitation of noise and the Stochastic Resonance (SR) phenomenon as a mechanism to mitigate the impact of variability. While SR has been already demonstrated in ReRAM devices and its potential impact has been analyzed for memory applications, related works have only focused on voltage input signals. In this work we present preliminary results concerning the exploration of SR in current-driven ReRAM devices, commercially available by Knowm Inc. Our results indicate that additive noise of amplitude s = 0.125uA can stabilize the cycling performance of the devices, whereas higher noise amplitude improves the HRS-LRS resistance window, thus could affect positively the Bit Error Rate (BER) metric in ReRAM memory applications., Supported by the Chilean research grants FONDECYT INICIACION 11180706 and ANID-Basal FB0008, and by the Spanish MCIN grants PID2019-105658RB-I00, and MCIN/AEI/10.13039/501100011033 grant PID2019-103869RB-C33., Peer Reviewed, Postprint (author's final draft)