Pasar al contenido principal

Fabrication, characterization and modelling of advanced micro and nano-electronic devices

RYC2020-030150-I

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Ramón y Cajal
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Modeling and Simulation of Correlated Cycle-to-Cycle Variability in the Current-Voltage Hysteresis Loops of RRAM Devices

  • Salvador Aguilera, Emili|||0000-0002-1613-6784
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Rodriguez, R.|||0000-0002-4565-6703
  • Miranda, E.|||0000-0003-0470-5318
Resistive RAMs or memristors are nowadays considered serious candidates for the implementation of energy efficient and scalable neuromorphic computing systems. However, a major drawback of this technology is the instability of the device current-voltage (I-V) characteristic as is clearly revealed by the so-called cycle-to-cycle (C2C) variability. This lack of complete reproducibility is a consequence of the spontaneous or induced morphological changes of the filamentary conducting structure occurring at atomic level. Variability is an essential issue any compact model for the conduction characteristics of RRAM devices should be able to cope with to be considered realistic. In this work, a thorough investigation of the C2C variability in the I-V loops of HfO-based memristive structures was carried out with the aim of incorporating this information into the equations of the Dynamic Memdiode Model. From the compact modeling viewpoint, C2C correlation effects are achieved using model parameters expressed as mean-reverting stochastic processes driven by Wiener noise (Ornstein-Uhlenbeck process). The direct and indirect links between the random behavior of the model parameters and the observable magnitudes (high and low resistance states, set and reset voltages, etc.) are discussed. The agreement between simulation and experimental results is statistically assessed using the Wasserstein's distance metric.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Impact of the W etching process on the resistive switching properties of TiN/Ti/HfO2/W memristors

  • Saludes Tapia, Maria Mercedes|||0000-0002-7091-4866
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Miranda, E.|||0000-0003-0470-5318
  • González, M. B.
In this work, we investigate the effects related to the etching process of the W bottom electrode (BE) on the breakdown voltages and the resistive switching (RS) characteristics of TiN/Ti/HfO/W memristors. Two different W-BE etching processes are compared: anisotropic dry etching and isotropic wet etching. In order to complete the analysis, scanning electron microscope inspections are used to investigate the profile of the patterned BE. Finally, the hysteretic current-voltage (I-V) characteristics are simulated using the Dynamic Memdiode Model (DMM).
Dipòsit Digital de Documents de la UAB
Publicación Capítulo o parte de un libro (BookPart)

Impact of the Ti/HfO2 Thickness Ratio on the Resistive Switching Characteristics of Memristive Devices

  • Saludes Tapia, Maria Mercedes|||0000-0002-7091-4866
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Miranda, E.|||0000-0003-0470-5318
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
This work investigates the impact of the Ti thickness on the resistive switching behavior of Ti/HfO-based memristors, with particular focus on the Ti-to-HfO thickness ratio (t/t). Understanding the interplay between the Ti layer and the switching dynamics of the devices is crucial for enhancing their performance and opening up new opportunities for advanced applications. This paper provides a comprehensive analysis of how a modification of the (t/t) ratio affects the Resistive Switching characteristics of the devices. The reported results allow us to identify the optimal conditions required to achieve enhanced memristor functionality, which is essential for applications such as data storage and neuromorphic computing.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal Characterization of Conductive Filaments in Unipolar Resistive Memories

  • Aguilera-Pedregosa, Cristina
  • Maldonado, David
  • González, M. B.
  • Moreno, Enrique
  • Jiménez-Molinos, Francisco
  • Campabadal, Francesca
  • Roldán, J.B.
A methodology to estimate the device temperature in resistive random access memories (RRAMs) is presented. Unipolar devices, which are known to be highly influenced by thermal effects in their resistive switching operation, are employed to develop the technique. A 3D RRAM simulator is used to fit experimental data and obtain the maximum and average temperatures of the conductive filaments (CFs) that are responsible for the switching behavior. It is found that the experimental CFs temperature corresponds to the maximum simulated temperatures obtained at the narrowest sections of the CFs. These temperature values can be used to improve compact models for circuit simulation purposes., The authors thank the support of the Consejería de Conocimiento, Investigación y Universidad, Junta de Andalucía (Spain), and the FEDER program for the projects B-TIC-624-UGR20. M.B.G acknowledges the Ramón y Cajal grant No. RYC2020-030150-I., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

True Random Number Generator Based on RRAM-Bias Current Starved Ring Oscillator

  • Arumi, Daniel
  • Manich, S.
  • Gomez-Pau, Álvaro
  • Rodriguez-Montanes, Rosa
  • Bargallo, Mireia G.
  • Campabadal, Francesca
This work presents a resistive random access memory (RRAM)-bias current-starved ring oscillator (CSRO) as true random number generator (TRNG), where the cycle-to-cycle variability of an RRAM device is exploited as source of randomness. A simple voltage divider composed of this RRAM and a resistor is considered to bias the gate terminal of the extra transistor of every current starved (CS) inverter of the ring oscillator (RO). In this way, the delay of the inverters is modified, deriving an unpredictable oscillation frequency every time the RRAM switches to the high resistance state (HRS). The oscillation frequency is finally leveraged to extract the sequence of random bits. The design is simple and adds low area overhead. Experimental measurements are performed to analyze the cycle-to-cycle variability in the HRS. The very same measurements are subsequently used to validate the TRNG by means of electrical simulations. The obtained results passed all the National Institute of Standards and Technology randomness tests (NIST) tests without the need for postprocessing., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Impact of the W etching process on the resistive switching properties of TiN/Ti/HfO<inf>2</inf>/W memristors

  • Saludes-Tapia, Mercedes
  • Campabadal, Francesca
  • Miranda, Enrique A.
  • González Bargallo, Mireia
In this work, we investigate the effects related to the etching process of the W bottom electrode (BE) on the breakdown voltages and the resistive switching (RS) characteristics of TiN/Ti/HfO2/W memristors. Two different W-BE etching processes are compared: anisotropic dry etching and isotropic wet etching. In order to complete the analysis, scanning electron microscope inspections are used to investigate the profile of the patterned BE. Finally, the hysteretic current–voltage (I-V) characteristics are simulated using the Dynamic Memdiode Model (DMM)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Variability and power enhancement of current controlled resistive switching devices

  • Vinuesa, G.
  • García, H.
  • Lendínez, J. M.
  • García-Ochoa, E.
  • González, Mireia
  • Maldonado, D.
  • Aguilera-Pedregosa, C.
  • Moreno, Eulalia
  • Jiménez-Molinos, F.
  • Roldán, J. B.
  • Campabadal, Francesca
  • Castán, H.
  • Dueñas, S.
In this work, the unipolar resistive switching behaviour of Ni/HfO2/Si(n+) devices is studied. The structures are characterized using both current and voltage sweeps, with the device resistance and its cycle-to-cycle variability being analysed in each case. Experimental measurements indicate a clear improvement on resistance states stability when using current sweeps to induce both set and reset processes. Moreover, it has been found that using current to induce these transitions is more efficient than using voltage sweeps, as seen when analysing the device power consumption. The same results are obtained for devices with a Ni top electrode and a bilayer or pentalayer of HfO2/Al2O3 as dielectric. Finally, kinetic Monte Carlo and compact modelling simulation studies are performed to shed light on the experimental results., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal effects on TiN/Ti/HfO<inf>2</inf>/Pt memristors charge conduction

  • Jiménez-Molinos, Francisco
  • Vinuesa, Guillermo
  • García, Hector
  • Tarre, Aivar
  • Tamm, Aile
  • Kalam, Kristian
  • Kukli, Kaupo
  • Dueñas, Salvador
  • Castán, Helena
  • González, Mireia
  • Campabadal, Francesca
  • Roldán, Juan Bautista
TiN/Ti/HfO2/Pt resistive switching devices have been fabricated, measured, and modeled. After programming the devices in the low resistance state, the current-voltage characteristic below the reset switching voltage was measured at different temperatures (from 90 to 350 K). A weak but complex temperature dependence was obtained for several voltage regimes. These memristors belong to a wider set known as valence change memories, whose conductance is determined by the formation of conductive filaments (CFs) linked to a high density of oxygen vacancies in a dielectric sandwiched between two metal electrodes. This usually leads to ohmic conduction in the low resistance state. However, a non-linear current dependence has been also observed in the measured devices, in addition to symmetric current-voltage curves for positive and negative biases in the 0-0.6 V voltage range. Three different thermal dependences have been considered for explaining the whole set of experimental data. Two of them are linked to ohmic filamentary conduction; the CF shows a conductivity enhancement due to thermally activated mechanisms at low temperatures; on the contrary, a CF conductivity degradation is observed at the higher temperatures. Finally, an additional slightly higher value for the non-linear current component as the temperature rises has also been taken into account. A semiempirical compact model has been implemented including these conduction mechanisms and their corresponding temperature dependences, the device has been simulated in LT-Spice and the experimental currents have been correctly reproduced., This research was supported by the projects A-TIC-117-UGR18, B-TIC-624-UGR20, and IE2017-5414 funded by the Consejería de Conocimiento, Investigación y Universidad, Junta de Andalucía (Spain), and the FEDER program. The study was also supported by the European Regional Development Fund project “Emerging Orders in Quantum and Nanomaterials” (No. TK134) and the Estonian Research Agency (PRG753). M.B.G. acknowledges the Ramón y Cajal under Grant No. RYC2020-030150-I., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of the voltage ramp rate on the conduction characteristics of HfO2-based resistive switching devices

  • García, Hector
  • Vinuesa, Guillermo
  • García-Ochoa, Elena
  • Aguirre, Fernando
  • González, Mireia Bargalló
  • Jiménez-Molinos, Francisco
  • Campabadal, Francesca
  • Roldán, Juan B.
  • Miranda, Enrique
  • Dueñas, Salvador
  • Castán, Helena
Memristive devices have shown a great potential for non-volatile memory circuits and neuromorphic computing. For both applications it is essential to know the physical mechanisms behind resistive switching; in particular, the time response to external voltage signals. To shed light in these issues we have studied the role played by the applied voltage ramp rate in the electrical properties of TiN/Ti/HfO2/W metal-insulator-metal resistive switching devices. Using an ad hoc experimental set-up, the current-voltage characteristics were measured for ramp rates ranging from 100 mV s−1-1 MV s−1. These measurements were used to investigate in detail the set and reset transitions. It is shown that the highest ramp rates allow controlling the resistance values corresponding to the intermediate states at the very beginning of the reset process, which is not possible by means of standard quasistatic techniques. Both the set and reset voltages increase with the ramp rate because the oxygen vacancies movement is frequency dependent so that, when the ramp rate is high enough, the conductive filaments neither fully form nor dissolve. In agreement with Chua’s theory of memristive devices, this effect causes the device resistance window to decrease as the ramp rate increases, and even to vanish for very high ramp rates. Remarkably, we demonstrate that the voltage ramp rate can be straightforwardly used to control the conductance change of the switching devices, which opens up a new way to program the synaptic weights when using these devices to mimic synapses for neuromorphic engineering applications. Moreover, the data obtained have been compared with the predictions of the dynamic memdiode model., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cycle-to-cycle variability analysis of Ti/Al<inf>2</inf>O<inf>3</inf>-based memristors

  • Rasbach, Julius
  • Saludes-Tapia, Mercedes
  • González, Mireia Bargalló
  • Campabadal, Francesca
In this work, an experimental analysis of the resistive switching behavior of TiN/Ti/Al2O3/W memristors is presented. The main focus is on the analysis of the variability of the key parameters during long series of cycles, using both sweep and pulsed voltage measurement sequences. In addition, the correlation of the resistive switching parameters between subsequent cycles has been investigated. The results demonstrate that memristors based on Ti/Al2O3 exhibit a low cycle-to-cycle variability between consecutive cycles, indicating their potential use for emerging applications., Consejo Superior de Investigaciones Científicas (España) Agencia Estatal de Investigación (España), Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Exploring Conductance Quantization Effects in Electroformed Filaments for Their Potential Application to a Resistance Standard

  • Suñé, Jordi|||0000-0003-0108-4907
  • Aguirre, Fernando Leonel|||0000-0001-7793-1194
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Miranda, E.|||0000-0003-0470-5318
The ballistic conduction through narrow constrictions connecting charge reservoirs exhibits conductance quantization effects. Since the quantum of conductance (Formula presented.) is only related to fundamental constants of nature, these effects might allow the implementation of a standard of resistance, fulfilling the requirements of the 2019 revised International System of Units. Moreover, this standard would be able to work at room temperature and without a magnetic field, thus allowing its on-chip implementation. In this work, the authors propose that breakdown filaments in thin oxide layers might be useful to this purpose. In particular, conductance quantization effects in nanolaminate AlO/HfO dielectrics are reported and the role of intrinsic values of conductance and extrinsic parasitic elements are analyzed. The fact that breakdown filaments are irreversible is an advantage due to their expected stability and to the lack of cycle-to-cycle variations (as compared to resistive switching devices). Although the reported sample-to-sample variations are still too large for a real application, there is room for improving the controlover breakdown filaments through material design and electroforming conditions. Provided that this control is achieved, an on-chip implementation of a resistance standard for the realization of self-calibrating electrical systems and equipment with zero-chain traceability would be possible.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Modeling and simulation of successive breakdown events in thin gate dielectrics using standard reliability growth models

  • Miranda, E.|||0000-0003-0470-5318
  • Aguirre, Fernando Leonel|||0000-0001-7793-1194
  • Salvador, E.
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Suñé, Jordi|||0000-0003-0108-4907
The application of constant electrical stress to a metal-insulator-semiconductor (MOS) or metal-insulator-metal (MIM) structure can generate multiple breakdown events in the dielectric film. Very often, these events are detected as small jumps in the current-time characteristic of the device under test and can be treated from the stochastic viewpoint as a counting process. In this letter, a wide variety of standard reliability growth models for this process are assessed in order to determine which option provides the best simulation results compatible with the experimental observations. For the generation of the breakdown event arrivals, two alternative stochastic methods for the power-law Poisson process are investigated: first, the inversion algorithm for the cumulative distribution function and second, an on-the-fly method based on the so-called rejection algorithm. Though both methods are equivalent, the first one is more appropriate for data analysis using spreadsheet calculations while the second one is highly suitable for circuit simulation environments like LTSpice. The connection of the selected nonhomogeneous Poisson process with the Weibull model for dielectric breakdown is also discussed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Event-Driven Stochastic Compact Model for Resistive Switching Devices

  • Suñé, Jordi|||0000-0003-0108-4907
  • Bargallo Gonzalez, Mireia|||0000-0001-6792-4556
  • Saludes Tapia, Maria Mercedes|||0000-0002-7091-4866
  • Campabadal, Francesca|||0000-0001-7758-4567
  • Miranda, E.|||0000-0003-0470-5318
A stochastic compact model for resistive switching (RS) devices is presented. The motivation is twofold: first, introducing variability in a natural way, and second, accounting for the discrete jumps of conductance observed during set and reset transitions. The model is based on an event generation rate, and it is an 'on-the-fly' procedure because events are randomly generated as the simulation proceeds in time. For the generation of events, we assume a mixed nonhomogeneous Poisson process (NHPP). Before considering RS, we deal with the generation of successive breakdown (BD) events in metal-insulator-semiconductor structures. This confirms the validity of the approach by comparing it with experimental data in which discrete events are evident. To deal with RS, we transform a previous compact model into a stochastic model. Comparison with experiments in TiN/Ti/HfO2/W devices shows the validity of the approach. Current-voltage loops and potentiation-depression transients in pulsed experiments are captured with a single set of parameters. Moreover, the model is an adequate framework to deal with both cycle-to-cycle and device-to-device variability.