Pasar al contenido principal

DEGRADACION MECANICA DE MATERIALES DENTALES

PID2019-105377RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE EXTREMADURA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bioinspired design of triboceramics: Learning from the anisotropic microfracture response of dental enamel under sliding contact

  • Sanchez-Gonzalez, Estibaliz
  • Rodriguez-Rojas, Fernando
  • Borrero-Lopez, Oscar
  • Ortiz, Angel L.
  • Guiberteau, Fernando
  • Pinilla-Cienfuegos, Elena|||0000-0002-3734-0821
[EN] In the quest for novel ceramics for tribological applications via bioinspired design, the differences in the fracture modes that arise upon scratching relevant locations of ceramic-like tooth enamel are investigated. It is found that fracture initiates from weak rod-sheath interfaces at relatively low loads, independent of the sliding direction. However, the geometry and propagation of the cracks depends on the orientation of the interfaces relative to the maximum tensile stress: scratching along the occlusal surface propagates approximately sinusoidal cracks, parallel to the sliding direction, while scratching along the cross-section produces straight cracks that propagate normal (scratch parallel to occlusal surface) or parallel (scratch perpendicular to occlusal surface) to the sliding direction. The formation of cracks is hindered in scratching near the enamel-dentine junction. Implications for the microstructural design of triboceramics (bulks and coatings) with improved durability are discussed., The authors wish to thank Dr Florencio Monje Gil for kindly providing tooth specimens from his clinic (CICOM, Centro de Implantologia Cirugia Oral y Maxilofacial, Badajoz, Spain). This study was supported by Junta de Extremadura, Spain, and FEDER/ERDF funds (grants IB16139 and GR18149), and the Spanish Ministry of Science and Innovation (grant PID2019-105377RB-I00). E. P.-C. gratefully acknowledges support from the Spanish Ministry of Economy and Competitiveness (MINECO) under grant FJCI-2015-27228.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of a DLC film on the sliding-wear behaviour of Ti6Al4V: Implications for dental implants

  • Rodriguez-Rojas, Fernando
  • Borrero-Lopez, Oscar
  • Bendavid, Avi
  • Martin, Philip J.
  • Hoffman, Mark
  • Kovylina-Zabyako, Miroslavna
  • Pinilla-Cienfuegos, Elena|||0000-0002-3734-0821
[EN] Titanium alloys are widely used in parts of dental implants, such as screws and abutments. In practice, unwanted relative sliding between contacting implant parts can cause excessive wear, which may lead to early failure. The effect of a submicron diamond-like carbon (DLC) coating on the friction and wear of Ti6Al4V alloys under sliding contact in artificial saliva was investigated. Critically, the DLC film suppressed adhesion between contacting surfaces, significantly lowered the coefficient of friction and contact stress, and ultimately the wear rate, relative to uncoated Ti6Al4V, while maintaining good film-substrate bonding and undergoing a limited extent of fracture. Results are explained within the framework of contact mechanics. Implications for the development of durable dental implants are discussed., This study was supported by the Ministry of Science and Innovation, Spain (grant no. PID2019-105377RB-I00) . E.P.-C gratefully acknowl- edges funding from the Generalitat Valenciana (Grant No. SEJIGENT/2021/039).