Pasar al contenido principal

NANOSENSORES PARA LA MONITORIZACION SIMULTANEA ELECTRICA Y OPTICA DE GASES DE CAMBIO CLIMATICO

PID2019-107697RB-C42

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrothermal Synthesis and Annealing Effect on the Properties of Gas-Sensitive Copper Oxide Nanowires

  • Claros, Martha
  • Gràcia Tortadès, Isabel
  • Figueras Costa, Eduard
  • Vallejos, Stella
In this study, we report a straightforward and reproducible hydrothermal synthesis of copper oxide nanowires, their morphological and chemical characterization, and their application in gas sensing. Results show that the hydrothermal process is mainly influenced by the reaction time and the concentration of the reducing agent, demonstrating the synthesis of fine and long nanowires (diameter of 50–200 nm and length of 25 µm) after 10 h of reaction with 0.1 M of pyrrole. Two different annealing temperatures were tested (205 and 450 °C) and their effect on the morphology, chemical composition, and crystal size of the nanowires was analyzed by SEM, XPS, and XRD techniques, respectively. The analysis shows that the Cu<sup>2+</sup> oxidation state is mainly obtained at the higher annealing temperature, and the nanowires’ shape suffers a transformation due to the formation of agglomerated crystallites. The gas sensing tests for acetone, ethanol, toluene, and carbon monoxide show preferential response and sensitivity to acetone and ethanol over the other analytes. The annealing temperature proves to have a higher influence on the stability of the nanowires than on their gas sensitivity and selectivity, showing better medium-term stability for the nanowires annealed at 450 °C., This research was funded by the Czech Science Foundation (GAČR) via Grant no. 20-20123S. This research was made using the infrastructures of CEITEC NanoLab Research Infrastructure supported by MEYS CR (LM2018110). We also acknowledge the support of the MCIN/AEI/10.13039/501100011033 via Grant PID2019-107697RB-C42 (ERDF A way of making Europe)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

UV-light activated APTES modified WO<inf>3-x</inf> nanowires sensitive to ethanol and nitrogen dioxide

  • Tomić, Milena
  • Fohlerova, Zdenka
  • Gràcia Tortadès, Isabel
  • Figueras, Eduard
  • Cané, Carles
  • Vallejos, Stella
The sensing properties of (3-aminopropyl)triethoxysilane modified tungsten oxide nanowires (APTES@WO3-x) based sensors towards several gases and vapors are reported in this work. The developed sensors show high sensitivity to ethanol and nitrogen dioxide under UV-irradiation at room temperature (24 °C). Gas sensing results demonstrate enhanced sensing properties for the APTES@WO3-x compared to non-modified WO3-x sensors, with the APTES@WO3-x sensors showing approximately 17 and 20 times more sensitivity to ethanol and nitrogen dioxide, respectively, compared to the non-modified WO3-x sensors. The APTES@WO3-x sensors also display improved selectivity to nitrogen dioxide (oxidizing gas) and ethanol (among other reducing gases including acetone, toluene, hydrogen, and carbon monoxide). These results are attributed to the presence of the reactive amino group at the APTES@WO3-x sensors, which facilitates the chemical interaction with nitrogen dioxide and ethanol and the electron transfer towards/from WO3-x under UV-light excitation., This work has been supported by the Spanish Ministry of Science and Innovation via Grant TEC2016-79898-C6-1-R, PID2019-107697RB-C42 (AEI/FEDER, EU) and the Ramón y Cajal programme, and the Czech Science Foundation (GAČR) via Grant No 20-20123S. This research has made use of the infrastructures of the Spanish ICTS Network MICRONANOFABS, partially supported by MINECO, and Czech CEITEC Nano Research Infrastructure, supported by MEYS CR (LM2018110)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gas-phase synthesis of iron silicide nanostructures using a single-source precursor: Comparing direct-write processing and thermal conversion

  • Jungwirth, Felix
  • Salvador-Porroche, Alba
  • Porrati, Fabrizio
  • Jochmann, Nicolas P.
  • Knez, Daniel
  • Huth, Michael
  • Gràcia Tortadès, Isabel
  • Cané, Carles
  • Cea, Pilar
  • Teresa, José María de
  • Barth, Sven
The investigation of precursor classes for the fabrication of nanostructures is of specific interest for maskless fabrication and direct nanoprinting. In this study, the differences in material composition depending on the employed process are illustrated for focused-ion-beam- and focused-electron-beam-induced deposition (FIBID/FEBID) and compared to the thermal decomposition in chemical vapor deposition (CVD). This article reports on specific differences in the deposit composition and microstructure when the (H3Si)2Fe(CO)4 precursor is converted into an inorganic material. Maximum metal/metalloid contents of up to 90 at. % are obtained in FIBID deposits and higher than 90 at. % in CVD films, while FEBID with the same precursor provides material containing less than 45 at. % total metal/metalloid content. Moreover, the Fe:Si ratio is retained well in FEBID and CVD processes, but FIBID using Ga+ ions liberates more than 50% of the initial Si provided by the precursor. This suggests that precursors for FIBID processes targeting binary materials should include multiple bonding such as bridging positions for nonmetals. In addition, an in situ method for investigations of supporting thermal effects of precursor fragmentation during the direct-writing processes is presented, and the applicability of the precursor for nanoscale 3D FEBID writing is demonstrated., S.B. acknowledges funding by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) in the Heisenberg Programme (BA 6595/1-1) and through grants BA 6595/2-2 and BA 6595/5-1. M.H. thanks the Deutsche Forschungsgemeinschaft for financial support through grant HU 752/16-1. D.K. acknowledges funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 823717-ESTEEM3. In addition, S.B. thanks Prof. A. Terfort and Prof. M. Wagner for their support at Goethe University Frankfurt. The work was also supported in part by the COST Action COST-FIT4NANO (action CA19140) by providing funding for a STSM of A.S.-P. I.G. and C.C. acknowledge funding by the Spanish Ministry of Science and Innovation via Grant PID2019-107697RB-C42 (AEI/FEDER, EU). J.M.D.T. acknowledges financial support by grant PID2020-112914RB-I00 funded by MCIN/AEI/10.13039/501100011033 and Gobierno de Aragón via grant E13_23R with European Social Funds (Construyendo Europa desde Aragón). A.S.-P. and P.C. are grateful for financial assistance in the framework of the projects PID2019-105881RB-I00 and TED2021-131318B-I00 funded by MCIN/AEI/10.13039/501100011033 and European Union “NextGenerationEU”/PRTR as well as Gobierno de Aragón through the grant E31_23R with European Social Funds (Construyendo Europa desde Aragón). This work was conducted within the Frankfurt Center for Electron Microscopy (FCEM). Technical support by the LMA technicians at Universidad de Zaragoza is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ChemFET gas nanosensor arrays with alignment windows for assembly of single nanowires

  • Chmela, Ondřej
  • Gablech, Imrich
  • Sadílek, Jakub
  • Brodský, Jan
  • Vallejos, Stella
This work focuses on the fabrication and characterization of ChemFET (Chemical Field-Effect Transistor) gas nanosensor arrays based on single nanowire (SNW). The fabrication processes include micro and nanofabrication techniques enabled by a combination of ultraviolet (UV) and e-beam lithography to build the ChemFET structure. Results show the integration and connection of SNWs across the multiple pairs of nanoelectrodes in the ChemFET by dielectrophoresis process (DEP) thanks to the incorporation of alignment windows (200–300 nm) adapted to the diameter of the NWs. Measurements of the SNW ChemFET array’s output and transfer characteristics prove the influence of gate bias on the drain current regulation. Tests upon hydrogen (H2) and nitrogen dioxide (NO2) as analyte models of reducing and oxidizing gases show the ChemFET sensing functionality. Moreover, results demonstrate better response characteristics to H2 when the ChemFET operates in the subthreshold regime. The design concepts and methods proposed for fabricating the SNW-based ChemFET arrays are versatile, reproducible, and most likely adaptable to other systems where SNW arrays are required. [Figure not available: see fulltext.], This work was supported by the Czech Science Foundation (GAČR, No. 22-14886S), and the MCIN/AEI/10.13039/501100011033 (No. PID2019-107697RB-C42 (ERDF A way of making Europe)). Funding note: Open access publishing supported by the National Technical Library in Prague., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Aerosol assisted chemical vapor deposition routes for the selective formation of gas sensitive iron oxide structures

  • Tomić, Milena
  • Gràcia, Isabel
  • Figueras, Eduard
  • Cané, Carles
  • Vallejos, Stella
Iron oxide (Fe2O3) structures with various morphologies are synthesized by aerosol-assisted chemical vapor deposition (AACVD) method. The structures are formed reproducibly by tuning different AACVD synthesis parameters, including temperatures, solvents, and samples’ position in the reaction chamber. The properties of these structures are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). Results demonstrate the formation of six types of crystalline Fe2O3 structures - flattened pyramids (fPy), pyramids (Py), porous pyramids (pPy), sheets (Sh), bricks (Br), and quasi-spherical particles (qsP). The formation of these structures is mainly connected with the use of acetone or acetone/ethanol mixture as solvents and their effect on boosting the influence of the temperature or sample’s position, respectively, on the properties of the structures. The gas sensing tests of the structures with higher aspect ratios or porosity (pPy, Py, fPy, and Sh) showed responses to various gases (acetone, ethanol, toluene, carbon monoxide, hydrogen, methane, ammonia, and nitrous oxide), reporting maximum sensitivity and selectivity to acetone and ethanol. The best results recorded are for the porous pyramids which show sensitivities of 5.1 % ppm− 1 and 3.9 % ppm− 1 (in the range of 10–40 ppm) to acetone and ethanol, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Replication data for Aerosol assisted chemical vapor deposition routes for the selective formation of gas sensitive iron oxide structures

  • Tomić, Milena
  • Gràcia, Isabel
  • Figueras, Eduard
  • Cané, Carles
  • Vallejos, Stella
Iron oxide (Fe<inf>2</inf>O<inf>3</inf>) structures with various morphologies are synthesized by aerosol-assisted chemical vapor deposition (AACVD) method. The structures are formed reproducibly by tuning different AACVD synthesis parameters, including temperatures, solvents, and samples' position in the reaction chamber. The properties of these structures are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). Results demonstrate the formation of six types of crystalline Fe<inf>2</inf>O<inf>3</inf> structures - flattened pyramids (fPy), pyramids (Py), porous pyramids (pPy), sheets (Sh), bricks (Br), and quasi-spherical particles (qsP). The formation of these structures is mainly connected with the use of acetone or acetone/ethanol mixture as solvents and their effect on boosting the influence of the temperature or sample's position, respectively, on the properties of the structures. The gas sensing tests of the structures with higher aspect ratios or porosity (pPy, Py, fPy, and Sh) showed responses to various gases (acetone, ethanol, toluene, carbon monoxide, hydrogen, methane, ammonia, and nitrous oxide), reporting maximum sensitivity and selectivity to acetone and ethanol. The best results recorded are for the porous pyramids which show sensitivities of 5.1 % ppm<sup>−1</sup> and 3.9 % ppm<sup>−1</sup> (in the range of 10–40 ppm) to acetone and ethanol, respectively., We acknowledge the support of MCIN/ AEI /10.13039/501100011033 via Grant PID2019-107697RBC42 ., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoscale, surface-confined phase separation by electron beam induced oxidation

  • Barth, Sven
  • Porrati, Fabrizio
  • Knez, Daniel
  • Jungwirth, Felix
  • Jochmann, Nicolas P
  • Huth, Michael
  • Winkler, Robert
  • Plank, Harald
  • Gracia, Isabel
  • Cané, Carles
Electron-assisted oxidation of Co-Si-based focused electron beam induced deposition (FEBID) materials is shown to form a 2-4 nm metal oxide surface layer on top of an electrically insulating silicon oxide layer less than 10 nm thick. Differences between thermal and electron-induced oxidation on the resulting microstructure are illustrated., S. B. acknowledges funding by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) in the Heisenberg Programme (BA 6595/1-1) and through grants BA 6595/2-2 and BA 6595/5-1. M. H. thanks the Deutsche Forschungsgemeinschaft for financial support through grant HU 752/16-1. D. K. acknowledges funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no. 823717-ESTEEM3. I. G. and C. C. acknowledge funding by the Spanish Ministry of Science and Innovation via Grant PID2019-107697RB-C42 (AEI/FEDER, EU). H. P. and R. W. gratefully acknowledge the financial support by the Austrian Federal Ministry for Digital and Economic Affairs and the National Foundation for Research, Technology, and Development (Christian Doppler Laboratory, DEFINE, Austria). In addition, S. B. thanks Prof. A. Terfort and Prof. M. Wagner for their support at Goethe University Frankfurt. This work was conducted within the Frankfurt Center for Electron Microscopy (FCEM). Martina Dienstleder is gratefully acknowledged for TEM specimen preparation., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

VOCs Sensing by Metal Oxides, Conductive Polymers, and Carbon-Based Materials

  • Tomic, Milena|||0000-0002-6378-2383
  • Šetka, Milena
  • Vojkůvka, Lukaš
  • Vallejos, Stella|||0000-0002-7415-5414
This review summarizes the recent research efforts and developments in nanomaterials for sensing volatile organic compounds (VOCs). The discussion focuses on key materials such as metal oxides (e.g., ZnO, SnO, TiO WO), conductive polymers (e.g., polypyrrole, polythiophene, poly(3,4-ethylenedioxythiophene)), and carbon-based materials (e.g., graphene, graphene oxide, carbon nanotubes), and their mutual combination due to their representativeness in VOCs sensing. Moreover, it delves into the main characteristics and tuning of these materials to achieve enhanced functionality (sensitivity, selectivity, speed of response, and stability). The usual synthesis methods and their advantages towards their integration with microsystems for practical applications are also remarked on. The literature survey shows the most successful systems include structured morphologies, particularly hierarchical structures at the nanometric scale, with intentionally introduced tunable "decorative impurities" or well-defined interfaces forming bilayer structures. These groups of modified or functionalized structures, in which metal oxides are still the main protagonists either as host or guest elements, have proved improvements in VOCs sensing. The work also identifies the need to explore new hybrid material combinations, as well as the convenience of incorporating other transducing principles further than resistive that allow the exploitation of mixed output concepts (e.g., electric, optic, mechanic).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

ZnO Structures with Surface Nanoscale Interfaces Formed by Au, FeO, or CuO Modifier Nanoparticles, Characterization and Gas Sensing Properties

  • Tomic, Milena|||0000-0002-6378-2383
  • Claros, Martha|||0000-0003-2144-3620
  • Gràcia, Isabel|||0000-0001-8563-9468
  • Figueras Costa, Eduardo|||0000-0002-4229-3214
  • Cané, Carles|||0000-0003-0676-9294
  • Vallejos Vargas, Stella
Zinc oxide rod structures are synthetized and subsequently modified with Au, FeO, or CuO to form nanoscale interfaces at the rod surface. X-ray photoelectron spectroscopy corroborates the presence of Fe in the form of oxide-FeO; Cu in the form of two oxides-CuO and CuO, with the major presence of CuO; and Au in three oxidation states-Au 3+, Au +, and Au 0, with the content of metallic Au being the highest among the other states. These structures are tested towards nitrogen dioxide, ethanol, acetone, carbon monoxide, and toluene, finding a remarkable increase in the response and sensitivity of the Au-modified ZnO films, especially towards nitrogen dioxide and ethanol. The results for the Au-modified ZnO films report about 47 times higher response to 10 ppm of nitrogen dioxide as compared to the non-modified structures with a sensitivity of 39.96% ppm -1 and a limit of detection of 26 ppb to this gas. These results are attributed to the cumulative effects of several factors, such as the presence of oxygen vacancies, the gas-sensing mechanism influenced by the nano-interfaces formed between ZnO and Au, and the catalytic nature of the Au nanoparticles.