Pasar al contenido principal

RECICLADO DE FIBRAS A PARTIR DE RESIDUOS DE ROPA Y REMANENTES TEXTILES PARA SU APLICACION EN MATERIALES DE CONSTRUCCION SOSTENIBLES

PID2019-108067RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 51
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Influence of long-fibre content on the reinforcement capacity of nonwovens obtained from recycled textile waste for application in cement composites

  • Julián Gómez, Bárbara
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Ventura Casellas, Heura|||0000-0003-3654-618X
The use of nonwoven fabrics made from recycled textile fibers as reinforcement for cement-based composites offers a synergistic solution for the textile industry and the building sector, both known for their significant environmental impacts. However, a primary limitation in the reinforcing capacity of these nonwovens is the short length of recycled fibers. To overcome this, incorporating longer virgin fibers becomes necessary, which can reduce the material's overall sustainability. Therefore, it is crucial to determine the optimal composition of nonwoven fabrics in terms of recycled short and virgin long fiber content to develop cement building materials with a strong balance of mechanical performance and sustainability. This study investigates the effect of long fiber content on the mechanical behavior of nonwovens prepared from recycled fibers, incorporating long fibers ranging from 0 % to 40 %. Nonwoven fabrics were produced using an enhanced carding and needle-punching method and subsequently characterized for their mechanical properties. Cement composite plates prepared with these nonwovens were then tested under bending and tensile forces to assess their performance. Composites reinforced with nonwovens containing 30 % and 40 % long fibers exhibited excellent flexural and tensile strength (>19 MPa and ∼4 MPa, representing increases of 37 % and 46 %, respectively) and a toughness increase exceeding 160 % compared to composites without long fibers. Digital Image Correlation (DIC) revealed more uniform crack distribution at higher long fiber content. A composition with 30 % long fibers (C30) emerged as the most suitable, offering an optimal balance between mechanical performance and a high recycled fiber content
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

TECTEX-Grupo de investigación en tecnología textil: investigación para contribuir a la transición verde y digital de la industria textil

  • Carrera Gallissà, Enric|||0000-0002-6990-4070
  • Algaba Joaquín, Inés María|||0000-0002-1962-6359
  • Buscio Olivera, Valentina|||0000-0002-0313-5299
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Cano Casas, Francesc|||0000-0002-4920-2194
  • Cayuela Marín, Diana|||0000-0002-1048-8340
  • Ilén, Elina Emilia
  • Oliver Ortega, Helena|||0000-0002-9398-8112
  • Riba Moliner, Marta|||0000-0003-0001-2055
  • Tornero García, José Antonio|||0000-0001-9479-825X
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
El grupo de investigación de ingeniería textil (TECTEX) INTEXTER y del Departamento de Ciencia e Ingeniería de Materiales de la Universitat Politècnica de Catalunya tiene como principal objetivo el desarrollo y optimización de nuevos materiales, procesos y tecnologías de la cadena de valor de la industria textil (desde la producción y caracterización de fibras y tejidos, procesos de tintura y acabado, hasta productos textiles). La finalidad de la actividad de nuestro grupo de investigación es reducir los impactos ambientales, aumentar la circularidad y optimizar los materiales, procesos y tecnologías textiles, así como desarrollar soluciones de alto valor añadido. Todo ello para contribuir a la creación de un sector textil más sostenible y competitivo. En particular, la investigación que llevamos a cabo en TECTEX se centra en contribuir a resolver los retos globales y las necesidades de competitividad industrial europea relacionadas con la transición ecológica y la transición digital, así como con el desarrollo de nuevas soluciones de alto valor añadido enfocadas principalmente al desarrollo de dispositivos y sistemas para aplicaciones biomédicas. En este artículo se presentarán los principales proyectos que actualmente estamos liderando desde nuestro grupo de investigación, como son los proyectos relacionados con la obtención de fibras naturales a partir de residuos agrícolas (HEMPQUAL), la obtención de colorantes naturales a partir de residuos agrícolas (OLIWASTEX), el reciclaje de residuos textiles por métodos mecánicos (RECYWASTEX), el desarrollo de materiales compuestos de cemento reforzados con fibras y estructuras textiles (RECYBUILDMAT), el electrohilado para aplicaciones biomédicas (ONCOFIBRAS y la aplicación del blockchain y trazabilidad a la industria textil (TRICK), Los proyectos presentados en este artículo han recibido financiación de las siguientes entidades: Gobierno de España, Agencia estatal de investigación: PID2019-108067RB-I00/ AEI/10.13039/501100011033 (proyecto RECYBUILDMAT) Gobierno de España y Unión Europea: TED2021-130611B-I00 (proyecto RECYWASTEX), financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea “NextGenerationEU”/PRTR Generalitat de Catalunya: ACE034/21/000053 (proyecto ONCOFIBRAS); 2021PROD00074 (proyecto OLIWASTEX), 2021PROD00079 (proyecto HEMPQUAL) Unión Europea: H2020-958352-TRICK (proyecto TRICK)
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental characterization of comfort performance parameters and multi-criteria sustainability assessment of recycled textile-reinforced cement facade cladding

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Hosseini, Seyed Mohammad Amin|||0000-0002-5558-6817
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Haurie Ibarra, Laia|||0000-0002-0732-8928
  • Lacasta Palacio, Ana María|||0000-0002-9060-6043
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Within the building construction sector, fiber cement boards have attracted interest as facade cladding materials in the last ten years, especially those that incorporate –for reinforcing purposes– natural and/or recycled synthetic fibers (i.e, from the textile industry). So far, the design-governing parameters of facade cladding panels have been mechanical strength, durability, constructability, aesthetics, insulation capacity, and fire resistance. From the sustainability perspective, the impact of the facade on the economic and energy efficiency performance is most often the parameter that leads the decision-making process. Within this context, the quantification of the sustainability performance of the facade –accounting for economic, environmental, and social indicators– is unfrequently carried out in design and project phases, this being attributed to the lack of methodologies that allow considering and quantifying some relevant indicators representative of the facade sustainability performance. As consequence, decisions made based on solely economic and on some of the environmental indicators might lead to solutions with lower sustainability performance than that required (or expected). Recycled textile waste fabric-reinforced cement board as a facade-cladding material for building envelopes is the focus of this research. In order to characterize the fire resistance, and thermal and acoustic insulation –as relevant serviceability parameters– of this material, an experimental program was carried out. Likewise, the sustainability performance of this facade-cladding is assessed through a method based on the Integrated Value Model for Sustainability Assessment (MIVES). This multi-criteria decision making (MCDM) model relies on the value function concept and the multi-disciplinary participation of experts to identify and quantify the relevant indicators of the facade sustainability performance and the relative importance of indicators and requirements. The MIVES-based model generated for this research can be straightforwardly used for assessing the sustainability performance of facade-cladding techniques made of any material and for any type of building (and location). The application of the MIVES model led to the sustainability index of this new material for facade-cladding ranging from 0.68 to 0.71 (/1.00) for different weighting scenarios., The authors express their gratitude to the Spanish Ministry of Economy, Industry, and Competitiveness for the financial support received under the scope of the projects CREEF (PID2019-108978RB-C32) and RECYBUILDMAT (PID2019-108067RB-I00)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Cement composite plates reinforced with nonwoven fabrics from technical textile waste fibres: Mechanical and environmental assessment

  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Álvarez del Castillo, María Dolores|||0000-0001-9956-0523
  • Gónzalez López, Laura
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
In this work, we present the development and characterisation of new cement-based composite panels reinforced with fibres recovered from wastes of protective technical clothing. The developed panels present a flexural strength (~15 MPa) and fracture toughness (~3.5 kJ/m2) that are suitable for their application on ventilated façades. The environmental impact of these panels was evaluated through the life-cycle assessment (LCA) from a cradle-to-gate approach and was compared with similar engineered materials and commercial materials used for ventilated façades (fibre cement facing tiles, ceramic tiles, and natural stone plates). Two functional units were assessed: the panel necessary to cover 1 m2 of façade, and the panel necessary to cover 1 m2 of façade providing a maximum bending stress of 17 or 24 MPa. For 17 MPa, the new composite developed has presented similar environmental performance to fibre cement facing tiles and significantly better than the traditional ceramic tiles and natural stone plates, This work was supported by the Spanish AEI (Agencia Estatal de Investigación, Government of Spain) [grant number PID2019-108067RB- I00]. The author Heura Ventura is a Serra-Húnter fellow. Monica Ardanuy aknowledges the Ministerio de Universidades (Ministry of Universities, Government of Spain) for the mobility grant PRX21/00264 (Subprograma de Movilidad, Plan Estatal de Investigación Científica y Técnica y de Innovación 2017–2020), Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Properties of phase change material impregnated vegetal nonwovens for use in cementitious composite reinforcement, Propietats de materials de canvi de fase impregnats en teixits no teixits vegetals per al seu ús com a reforç en compostos cimentosos, Propiedades de materiales de cambio de fase impregnados en no tejidos vegetales para su uso como refuerzo en compuestos cementicios

  • González Espinosa, Vanessa|||0000-0001-7974-1343
  • Lacasta Palacio, Ana María|||0000-0002-9060-6043
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
Natural fibres offer sustainable reinforcement for composites, while the construction sector seeks materials combining thermal regulation and mechanical performance. This work investigates the little-explored direct impregnation of nonwoven flax fibres with phase change materials (PCM) for multifunctional cement composites. Two PCMs with different phase transition temperatures (21 and 28 ¿C) were evaluated. The nonwoven impregnated with 28 ¿C PCM exhibited superior performance, both in thermal and mechanical terms, and for this reason it was selected for incorporation into the cementitious composites. In addition, a comparison was carried out with a microencapsulated PCM displaying a similar transition temperature. All composite samples underwent thermal analysis and mechanical tests. Thermal performance improvements relative to the control specimens (without PCM) resulted in a significant time delay in temperature response in all cases. The nonwoven impregnated composite manufactured above the transition temperature exhibited superior mechanical performance compared with microencapsulated PCM systems. Although showing lower strength than the control specimen without PCM, its remaining flexural strength of ~7 MPa highlights its potential for non-structural applications, including roof tiles and, in specific cases, ventilated façades., Peer Reviewed, 11 - Ciutats i Comunitats Sostenibles, 12 - Producció i Consum Responsables, 13 - Acció per al Clima, 9 - Indústria, Innovació i Infraestructura
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A textile waste fiber-reinforced cement composite: comparison between short random fiber and textile reinforcement

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Currently, millions of tons of textile waste from the garment and textile industries are generated worldwide each year. As a promising option in terms of sustainability, textile waste fibers could be used as internal reinforcement of cement-based composites by enhancing ductility and decreasing crack propagation. To this end, two extensive experimental programs were carried out, involving the use of either fractions of short random fibers at 6–10% by weight or nonwoven fabrics in 3–7 laminate layers in the textile waste-reinforcement of cement, and the mechanical and durability properties of the resulting composites were characterized. Flexural resistance in pre- and post-crack, toughness, and stiffness of the resulting composites were assessed in addition to unrestrained drying shrinkage testing. The results obtained from those programs were analyzed and compared to identify the optimal composite and potential applications. Based on the results of experimental analysis, the feasibility of using this textile waste composite as a potential construction material in nonstructural concrete structures such as facade cladding, raised floors, and pavements was confirmed. The optimal composite was proven to be the one reinforced with six layers of nonwoven fabric, with a flexural strength of 15.5 MPa and a toughness of 9.7 kJ/m2., This research was funded by the Spanish Ministry of Economy, Industry, and Competitiveness, RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Mechanical performance of aged cement-based matrices reinforced with recycled aramid textile nonwoven fabric: comparison with other FRCMs

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
Utilizing recycled fibers as reinforcement in cement-based matrices is an effective means of promoting waste recycling and adopting a circular economy approach in the construction industry. Within this framework, the recycling and potential reutilization of textile residues can improve the pre- and post-cracking performance of cement-based matrices intended for building components with up to intermediate structural responsibilities (i.e., panels and cladding elements for buildings). This research is focused on the mechanical and durability -through forced aging of dry-wet and freeze-thaw cycles- experimental characterization of laminated fabric-reinforced cementitious matrices (FRCMs) containing 4 and 6 nonwoven fabric layers obtained from end-of-life fire-protecting t-shirts. For this purpose, both direct and flexural tensile tests were conducted to characterize the mechanical performance of the composite. The tests on the 6-fabric layers produced panels with Portland Cement (PC) matrix, after 28-day of curing, led to average values of the maximum tensile strength of 3.7¿MPa with associated toughness index superior to 25¿kJ/m2, and mean modulus of rupture of 11.6¿MPa with a fracture energy index of 4.3¿kJ/m2. After dry-wet accelerated aging, the post-cracking performance of the developed composites decreased (on average, 40% in toughness and 11% in strength) due to fiber embrittlement. To better understand the performance of aged composites, shredded fibers recovered from protective clothing (mainly consisting of meta-aramid fibers) were immersed in the binary matrix. Accordingly, the mechanical properties of the fibers after 5 and 10 cycles of dry-wet aging were studied. Based on the results, replacing partially PC by silica fume (between 30% and 50%) was seen as a sustainable alternative to improve the performance of the aged fibers by more than 10%., The authors express their gratitude to the Agencia Estatal de Investigación, Spanish Ministry of Economy, Industry, and Competitiveness (Government of Spain) for the financial support received under the scope of the project RECYBUILDMAT (PID2019-108067RB-I00/AEI/10.13039/501100011033). Also, they acknowledge the funding of the research group TECTEX (2021 SGR 01056) from the Department de Recerca i Universitats de la Generalitat de Catalunya. The first author acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Cement composite panels reinforced with textile waste and flax nonwoven fabrics: flexural and accelerated aging performance

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
Towards more eco-friendly building materials, nonwoven fabrics from natural-based (flax) and recycled (textile waste) fibers were produced and incorporated into the cementitious composite panels. The textile waste fibers were recovered from two different clothing sources including fashion and fire-proofing garments. The flexural and durability (through forced wet-dry aging cycles) properties of the laminated sandwich-like cement panels reinforced with four different nonwoven fabrics (flax, treated flax, hybrid fashion textile waste/flax, and fire-proofing textile waste) were analyzed. Based on the results, all four different composites showed promising flexural-hardening behaviors in unaged conditions, especially those reinforced with the treated flax or hybrid fabrics which reached flexural strength of more than 16 MPa and energy ab-sorption index of more than 10 kJ/m2. After wet-dry aging, the post-cracking performance of all composites degraded due to fiber embrittlement, this was more evident for untreated flax composite (reduced by ~65%). Nonetheless, the treated flax fabric composite and hybrid fabric composite containing silica fume could show a better performance after aging., The authors express their gratitude to the Agencia Estatal de Investigación, Spanish Ministry of Economy, Industry, and Competitiveness (Government of Spain) for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00/AEI/10.13039/501100011033); 3D-Crete (2019PROD00066/IU68-017262-Codi project: J-02696); and CREEF (PID2019-108978RB-C32/AEI/10.13039/501100011033). The first author acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

The effect of fibres and carbonation conditions on the mechanical properties and microstructure of lime/flax composites

  • Rakhsh Mahpour, Ali|||0000-0002-7968-0250
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Rosell Amigó, Juan Ramón|||0000-0001-5034-8388
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
Fibre and textile-reinforced mortars are increasingly being used for a variety of building applications, including the strengthening of masonry structures. Lime mortars reinforced with sustainable fibres (such as vegetable or cellulosic fibres) may provide an interesting solution. In this paper, a mixture of commercial lime with 20% metakaolin addition was used to produce composites reinforced with non-woven flax fabrics that were cured at different moisture contents (from 0 to 100%) for 7 or 14 days in a CO2 incubator. The composites were char- acterised to determine their flexural behaviour, carbonation level and microstructure. According to the results, no differences exist in the flexural strength of the composites made in the moisture range of 33%–66%. At 7 days of curing, they attained Modulus of Rupture (MOR) values that exceeded 5.5. MPa. Moreover, it was observed that under high moisture conditions, the permeability of the fibres allows for CO2 access, despite the saturation of the pores of the matrix – allowing a reaction in the vicinity of the fibres –, while under dry conditions, the fibre’s moisture retention does not permit the carbonation of the matrix in their vicinity, even though complete carbonation takes place after 14 days
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Characterization of a textile waste nonwoven fabric reinforced cement composite for non-structural building components

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Large amounts of nonrenewable resources are depleted by the construction industry in addition to the generation of million tons of mineral waste and carbon dioxide gas every year. For the sake of a more sustainable consumption pattern of building materials, as well as for reducing the waste flux to landfills, the use of recycled materials and wastes should be researched and motivated. In this sense, textile waste (TW) nonwoven fabric from residues of the garments and textile industries are investigated as internal reinforcement for cement-based matrices to enhance ductility and cracking control. To this end, an extensive experimental program was carried out to characterize both the mechanical and durability properties of the composite. The results were compared with those obtained from flax nonwoven fabric, taken as a reference (FNH and FH composites). All the composites showed a remarkable improvement in terms of toughness and post-cracking stress-bearing capacity, six being the optimum number of TW reinforcing layers. Through the analysis of the results obtained, the feasibility of using TW composite as a potential construction material in non-structural applications was confirmed. The extension to structural applications of low-medium responsibility is still required further research; nonetheless, the results are promising to this respect., The authors express their gratitude to the Spanish Ministry of Economy, Industry and Competitiveness for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Study of the fire and thermal behaviour of façade panels made of natural fibre-reinforced cement-based composites

  • Gónzalez López, Laura
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Haurie Ibarra, Laia|||0000-0002-0732-8928
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
The thermal and fire behaviour of calcium aluminate cement-based composites with a variable metakaolin content (from 0 to 40 wt% addition) reinforced with nonwoven flax fabrics has been examined. The fire behaviour was assessed using epiradiator and small-scale fire testing. The composites did not emit smoke or generate flames, nor did they produce spalling. Their integrity was maintained above 1000 ¿C. Samples having a higher metakaolin content revealed a delay in the temperature of the unexposed surface until reaching 760 ¿C. The effect of exposure to high temperatures (250 ¿C, 450 ¿C, and 950 ¿C) on bending behaviour was examined. The fibres were found to maintain their reinforcing capacity up to 250 ¿C, while the matrix maintained its performance up to 450 ¿C. The addition of metakaolin reduced conductivity and diffusivity. The results of the thermal and fire behaviour of the tested composites indicated that they may be suitable for façade panels for outdoor applications, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A review of the electrical conductivity test methods for conductive fabrics

  • Xie, Zeyue
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
With the substantial growth of the smart textiles market, electrical properties are becoming a basic requirement for most of the advanced textiles used in the development of wearable solutions and other textile-based smart applications. Depending on the textile substrate, the test method to determine the electrical properties can be different. Unlike smart fibers and yarns, the characterization of the electrical properties of fabrics cannot be tested between two connection points because the result would not represent the behavior of the entire fabric, so the electrical properties must be related to an area. The parameters used to characterize the electrical properties of the fabrics include resistance, resistivity, and conductivity. Although all of them can be used to indicate electrical performance, there are significant differences between them and different methods available for their determination, whose suitability will depend on the function and the textile substrate. This paper revises the main parameters used to characterize the electrical properties of conductive fabrics and summarizes the most common methods used to test them. It also discusses the suitability of each method according to several intervening factors, such as the type of conductive fabric (intrinsically or extrinsically conductive), its conductivity range, other fabric parameters, or the final intended application. For intrinsically conductive woven fabrics, all the methods are suitable, but depending on the requirements of conductivity accuracy, the contact resistance from the measuring system should be determined. For intrinsically conductive knitted fabrics, two-point probe, Van der Pauw, and eddy current methods are the most suitable. And for intrinsically conductive nonwoven fabrics, two-point probe and four-point probe methods are the most appropriate. In the case of extrinsically conductive fabrics, the applied method should depend on the substrate and the properties of the conductive layer., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Serviceability parameters and social sustainability assessment of flax fabric reinforced lime-based drywall interior panels

  • Rakhsh Mahpour, Ali|||0000-0002-7968-0250
  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Haurie Ibarra, Laia|||0000-0002-0732-8928
  • Lacasta Palacio, Ana María|||0000-0002-9060-6043
  • Rosell Amigó, Juan Ramón|||0000-0001-5034-8388
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
In the search of more environmentally-friendly construction materials, the use of natural-based fibers has gained much attention as reinforcement in the inorganic-based matrix. In this paper, the nonwoven flax fabric reinforced lime composites are created using a dewatering technique, and the serviceability parameters –thermal conductivity, sound absorption coefficient, and residual flexural resistance after exposure to elevated temperature– are determined experimentally. The tests are carried out on two different lime composites prepared under two distinct curing regimens, i.e., accelerated carbonation in a CO2 chamber and natural carbonation in laboratory conditions, to evaluate the effect of forced carbonation. In addition, the experimental results of the serviceability parameters are included in the MIVES model (Integrated Value Model for Sustainability Assessment) to evaluate the social sustainability of the developed material as an interior drywall panel. MIVES, a type of multi-criteria decision-making method, is based on the value function concept and seminars with experts. According to the results of experimental tests, the accelerated cured sample has higher thermal conductivity (~4 times) and lower sound absorption coefficients (~20%) than the naturally cured one. Nonetheless, the flexural performance of the former is 50% (at room temperature) and 100% (at elevated temperature) better. As for the social sustainability index assessed by the MIVES-based multi-objective approach, it ranges between 0.65 and 0.75 (out of 1.0) for both lime composite panels, at least 20% higher than the control lime panel with no reinforcement. The sustainability model designed for this research can be used for assessing the social sustainability performance of other materials although the weights assigned by the experts could be adapted to reflect the perceptions and local preferences., This work was supported through the project grants PID2019-108067RB-I00/AEI/10.13039/501100011033 and PID2020-117530RB-I00/MCIN/AEI/10.13039/501100011033 by the Ministerio de Ciencia e Innovación (MCIN)/Agencia Estatal de Investigación (AEI) of the Spanish Government. The author Payam Sadrolodabaee acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant)., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Preliminary study on new micro textile waste fiber reinforced cement composite

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Large amounts of nonrenewable resources are depleted by the construction industry in addition to the generation of million tons of mineral waste and carbon dioxide gas every year. For the sake of a more sustainable consumption pattern of building materials, as well as for reducing the waste flux to landfills, the use of recycled materials and wastes should be researched and motivated. One of the promising wastes is textile waste from residues of the garments and textile industries. The recycling and reusing of textile waste would be beneficial for reducing CO2 emissions and energy intake. In this sense, there are already some studies regarding the thermal behavior of this type of material, however, the engineering design properties of textile waste fiber reinforced cement composites to identify the proper application have not been deeply investigated. Hence, the objective of this study was to evaluate the potentiality of using textile waste fiber as reinforcement in the cement paste. To this end, the composites with three different treatments were made and the optimum treatment was chosen based on the flexural test. The result is the feasibility of using this kind of fiber as reinforcement of mortar elements with dewatering treatment., This work was supported by the Spanish Government, Ministerio de Ciencia e Innovación [grant number PID2019-108067RB-I00]., Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Effect of accelerated aging and silica fume addition on the mechanical and microstructural properties of hybrid textile waste-flax fabric-reinforced cement composites

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Incorporating eco-friendly substances obtained from recycled resources and industrial by-products is gaining increased acceptance among building materials. In this context, a cementitious matrix containing supplementary cementitious materials (SCMs) reinforced by recycled fibers may be a promising solution from both a durability and sustainability perspective. This study presents an extensive experimental program carried out on a cement- based composite with Silica Fume (SF), reinforced with recycled textile waste (TW) nonwoven fabric. Initially, the mechanical strength (compression and flexure) of the Portland cement paste substituted with variable SF content (0%–30%) was characterized. Based on the results, laminate plates having six TW fabric layers impregnated with three different cement pastes
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Mechanical properties and durability of biobased fabric-reinforced lime composites intended for strengthening historical masonry structures

  • Rakhsh Mahpour, Ali|||0000-0002-7968-0250
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Rosell Amigó, Juan Ramón|||0000-0001-5034-8388
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
The use of lime-based composites reinforced with fabrics made of natural fibers, is a promising solution for the strengthening of historical masonry structures owing to its moderate mechanical strength, similar color and chemical compatibility, avoiding damage on the historical structure and contributing to crack-width control. In this study, a new lime-based composite reinforced with flax nonwoven fabrics is mechanically characterized to study its reinforcement potential in terms of strength, and stress distribution. To this end, laminate plates with lime/metakaolin matrix and four to six layers of fabric reinforcement were produced and totally carbonated in a CO2 chamber. Both the mechanical (flexural and tensile) and durability (against wet-dry cycles) properties of the composite were subsequently assessed. Furthermore, Digital Image Correlation (DIC) was carried out on tensile testing to study the stress distribution. The 6-layer composites displayed the best performance (with flexural and tensile strengths of approximately 5.3 MPa and 2.5 MPa, respectively), followed by the 5-layer and the 4-layer composites. The DIC analysis revealed a higher stress distribution in the 6-layer composites, with an increased number of cracks, although having a lower severity. As for durability, a decrease of 30–45% is observed in flexural strength, and of 6–18% in tensile strength, depending on the number of reinforcing layers. SEM analysis refers to fiber/matrix debonding as the cause of this decrease. No damage has been observed on the fiber surface, which retains its reinforcing capacity. All of the composites displayed strain-hardening behavior in both the unaged and aged conditions. Study outcomes are intended to serve as the basis for the creation of a future, compatible, reliable, and sustainable system given its potential application in the historical restoration of masonry structures, The authors wish to express their gratitude to the Spanish government’s Ministerio de Ciencia e Innovación (MCIN) and Agencia Estatal de Investigación (AEI) for the financial support provided within the scope of the RECYBUILDMAT project (PID2019–108067RB-I00MICIN/ AEI/10.13039/501100011033), and the Generalitat de Catalunya’s Agència de gestió d’Ajuts Universitaris i de Recerca (AGAUR) for the financial support provided to the TECTEX Research Group (2021 SGR 01056). The author Heura Ventura is a Serra-Húnter fellow
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Self-heating performance of conductive textile-reinforced cement-based composites

  • Xie, Zeyue
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Ventura Casellas, Heura|||0000-0003-3654-618X
The regular distribution of conductive networks in electrically conductive cement composites (ECCC) continues to be a challenge. This study attempted to develop an ECCC with optimal mechanical, electrical, and thermal properties, combining a non-woven conductive layer (made of stainless steel and polyester fibres –SS/PES-) with five additional non-woven reinforcing layers made of recycled textile waste fibres. Four ECCC were prepared, having distinct SS fibre contents (20%, 30%, 40%, 50%) in the conductive layer. Electrical resistivity, self-heating properties, flexural behaviour, and coefficient of linear thermal expansion were assessed. In addition, the specimens having the best heating performance from each sample underwent heating stability tests. Observations confirmed that all ECCCs adhered to Ohm’s law. ECCC displayed the highest resistivity at 20% SS fibre (around 21.3 × 10- 3 O m) and the lowest resistivity at 50% SS fibre (around 4.9 × 10- 3 O m). In terms of heating performance, ECCC containing 20% SS fibre displayed the best performance despite having the highest resistivity, reaching a temperature increase of approximately 46.2 ¿C under 21 V within 30 min and maintaining a residual temperature of approximately 8.7 ¿C after 30 min of cooling. In addition, for all of the ECCC samples, the electrical and heating effects remained consistent over 20 cycles. In mechanical terms, the ECCC had Modulus of Rupture (MOR) values ranging between approximately 9 and 13 MPa. The coefficient of linear thermal expansion (CLTE) was ~13 (10- 6 /¿C). Overall, the study highlights the potential of non-woven fabric as a conductive material in ECCC, offering stable and repeatable conductive networks, noting the ECCC’s broader applications., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Reciclado de fibras provenientes de residuos de ropa y remanentes textiles para su aplicación en materiales de construcción sostenibles (RECYBUILDMAT)

  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ventura Casellas, Heura|||0000-0003-3654-618X
Actualmente existe una creciente preocupación sobre la sostenibilidad del sector de la construcción debido a su gran contribución al cambio climático. Aproximadamente un tercio de las emisiones de CO2 son producidas por este sector, tanto durante la construcción como en la fase operativa de los edificios. Otro problema ambiental es la abundancia de residuos provenientes de ropa usada o de la producción de productos textiles, así como de subproductos de la agricultura. Una manera de lograr una mayor sostenibilidad es recuperar estos residuos para su uso como materia prima en materiales de construcción. Así, el uso de materiales de construcción más sostenibles y, particularmente, la reducción en la cantidad requerida de cemento es de gran interés. El objetivo principal de este proyecto se centra en desarrollar y caracterizar materiales de construcción sostenibles basados en cemento o cal mezclados con nanosilica producida a partir de subproductos de la agricultura del maíz y reforzados con telas no tejidas fabricadas con fibras recuperadas de desechos textiles, para su aplicación en paneles multifuncionales para fachadas ventiladas, pavimentos flotantes y placas para cubierta y para refuerzo de estructuras para obra de mampostería y cerámica para rehabilitación de edificios antiguos e históricos. El proyecto, financiado en el marco de la convocatoria “Retos Investigación 2019” del Ministerio de Ciencia e Innovación, se aborda desde una perspectiva interdisciplinar, que incluye paquetes de trabajo relacionados con el campo de la Ingeniería Textil e Ingeniería de Materiales y paquetes relacionados con la Ingeniería de la Construcción y Tecnología de la Edificación
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Characterization of cement composite plates reinforced with nonwovens obtained from technical waste fibres

  • Gónzalez López, Laura
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Ventura Casellas, Heura|||0000-0003-3654-618X
Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Flax fabric-reinforcement lime composite as a strengthening system for masonry materials: study of adhesion

  • Rakhsh Mahpour, Ali|||0000-0002-7968-0250
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Rosell Amigó, Juan Ramón|||0000-0001-5034-8388
The present study was designed to investigate the bond mechanism between flax nonwoven fabric reinforced lime mortars and four different types of masonry stones. The researchers carried out a comprehensive characterization of the mortars and stones, and analyzed the interface between these materials based onbondextensionandflexuralstrength.Theresultsshowedthatbondstrengthvalues were directly related to adherence extension, which was dependent on surface treatment (such as water, lime, and latex). The flexural tests conducted on stones strengthened with the flax nonwoven fabric reinforced lime composite revealed that the latex treatment showed the best performance. This study provides preliminary evidence that the use of flax nonwoven fabric reinforced lime composite maybeaneffective method for masonry strengthening. However, further research is necessary to reach a comprehensive conclusion. Further studies may include an investigation of the effects of different types of latex, the influence of curing conditions on bond strength, and the long-term performance of the strengthening system. The results of this research may have important implications for the conservation and strengthening of historic masonry structures, as well as for the design of new masonry constructions.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Evaluación de residuos textiles monomateriales para el refuerzo de compuestos de base cemento

  • Oliver Ortega, Helena|||0000-0002-9398-8112
  • Alvarez, Maria
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Ventura Casellas, Heura|||0000-0003-3654-618X
La gestión del abundante volumen de residuos textiles, en continuo crecimiento, y sus escasas opciones de reciclaje, representan uno de los grandes retos actuales de la industria textil. Además, las futuras restricciones respecto a este residuo por parte de la Unión Europea (EU), algunas de ellas de próxima aplicación como la obligación de su recolección en el sistema municipal de residuos o las restricciones de exportación de éste, una solución largamente empleada hoy en día, provocan que sea imperativo encontrar soluciones de reciclaje para este residuo. En este contexto, el proyecto RECYBUILDMAT propone la utilización del residuo textil post-consumo, a través de telas no tejidas, como refuerzo para materiales compuestos cementícios con aplicación en paneles para fachadas ventiladas, pavimentos o elementos de mampostería. De esta forma, no solamente se recupera y aprovecha un residuo de escasa reciclabilidad, incrementándose su circularidad, sino que contribuye a la sostenibilidad de otra de las grandes industrias contaminantes como lo es la industria de la construcción, y en especial la del cemento. No obstante, y a pesar de que los materiales preparados en el marco del proyecto han demostrado su viabilidad y sostenibilidad, la durabilidad podría verse afectada debido al ataque alcalino del cemento sobre las fibras empleadas como refuerzo. Para estudiar este ataque alcalino y ver el efecto que tenía en función de la naturaleza química de las fibras, en este trabajo se estudió el efecto simulante cementíceo en telas no tejidas monomateriales de fibras de lana, algodón, viscosa, poliéster, poliamida y acrílicas. Para ello, siguiendo una aproximación al estándar UNE-EN 12467, las telas se impregnaron con un simulante cementíceo (siguiendo la norma ASTM C1897-20) y se sometieron a 25 ciclos de secado y humedad. El uso del simulante de cemento fue necesario para poder analizar el ataque químico en las fibras. Así, a pesar de que quedaban restos del simulante en la superficie de las fibras, no eran tan voluminosos como los del cemento, permitiendo observar cambios en la morfología y estructura química de las fibras, pudiéndose evaluar si existían signos de degradación. Se concluyó que las fibras químicas de polímero sintético, a diferencia de las naturales y químicas de polímero natural, no muestran ninguna degradación, como es el caso de las fibras acrílicas, o muestran alguna ligera degradación, como las fibras de poliamida o poliéster, por lo que son las mejores candidatas para ser empleadas como refuerzo en los materiales compuestos de matriz cementícia, Desde el grupo de investigación agradecer a la Agencia Estatal de Investigación por la financiación para el proyecto RECYBUILDMAT (PID2019-108067RB-100) que ha permitido desarrollar estudio, y al Departament de Recerca i Universitats de la Generalitat de Catalunya por la financiación al grupo consolidado de investigación TECTEX (2021 SGR 01056). También agradecer a Formació i Treball por proporcionar las muestras de residuo post-consumo con las que se ha elaborado este trabajo. Finalmente, por parte de la autora María Álvarez, agradecer a la Fundación Textil Algodonera y a la Asociación Industria Textil Algodón (AITPA) por reconocer este estudio con el 1r Premio de Innovación al Talento Joven 2023
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Durability of eco-friendly strain-hardening cementitious composite incorporating recycled textile waste fabric and silica fume

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
To reach carbon neutrality, the use of more eco-friendly building materials derived from recycled resources and industrial by-products has been widely encouraged. The use of Portland cement (PC) and concrete as the most used material in the world, after water, ends in the release of million tonnes of CO2 into the atmosphere. On the other hand, fast fashion in the garment industry has resulted in a massive volume of textile waste (TW) that ends up in landfills worldwide. In this regard, a cementitious composite containing industrial by-products as a partial replacement of PC reinforced with recycled TW fibers could be a viable option in terms of both durability and sustainability. In this study, the durability of the hybrid TW/falx nonwoven fabric-reinforced cement composite modified with 30% Silica Fume (SF) was investigated by determining the effect of accelerated wet /dry cycles on the mechanical behavior (through the flexural test) and microstructural characteristics (through scanning and backscat-tered electron microscope). The results show that there was a negligible difference between the mechanical properties of the laminated composite treated with SF with respect to the one without SF in unaged conditions. Nonetheless, after accelerated aging, the fibers in the former could maintain their strength and flexibility, resulting in the composite with better post-cracking mechanical parameters by 40%. © 2022, fib. The International Federation for Structural Concrete. All rights reserved.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Mechanical and durability characterization of a new textile waste micro-fiber reinforced cement composite for building applications

  • Sadrolodabaee, Payam|||0000-0003-2789-4406
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Fiber reinforced mortars (FRM) are growingly used in several fields of building technology (e.g., façade panels, roofing, raised floors and masonry structures) as building elements. One of the promising type of fiber for these composite materials can be textile waste originated from cloth wastes. The use of this sort of recycled materials and wastes as cement reinforcement within the building sector can play a relevant role in sustainability, both the environmental, economic and social perspectives. In this paper, the design mechanical properties (flexural and compressive strengths at 7, 28 and 56 days as well as toughness and stiffness) together with durability properties of cement pastes reinforced with short Textile Waste Fiber (TWF) in contents ranging from 6 to 10 % by weight fraction cement was investigated. The results were compared with those obtained from Kraft Pulp pine Fiber (KPF), taken as reference. The main conclusion is the feasibility of using this type of fiber as potential reinforcement in construction materials with the optimum dosage of 8%. Although the flexural resistance and toughness of the TWF composite are lower than KPF control by almost 9%, the compressive strength and stiffness together with durability properties have proven to be enhanced respect to the reference composite., The authors express their gratitude to the Spanish Ministry of Economy, Industry and Competitiveness for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nuevo material de construcción a partir de residuos de ropa usada

  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ventura Casellas, Heura|||0000-0003-3654-618X
  • Oliver Ortega, Helena|||0000-0002-9398-8112
El nuevo material creado por el grupo de investigación TECTEX, del Campus de Terrassa, mejora las propiedades del fibrocemento, es muy resistente, más flexible que otros materiales de construcción, es ignífugo y contribuye a reducir el impacto medioambiental en la construcción y por la destrucción de los residuos textiles
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Upcycling fibers from end-of-life clothes & textile remnants for sustainable building materials: closing the loop for a circular economy (Recybuildmat)

  • Ardanuy Raso, Mònica|||0000-0002-9809-2577
  • Claramunt Blanes, Josep|||0000-0003-3546-5943
  • Ventura Casellas, Heura|||0000-0003-3654-618X
Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Reciclado de fibras provenientes de residuos de ropa y remanentes textiles para su aplicación en materiales de construcción sostenibles (RECYBUILDMAT)

  • Ardanuy Raso, Mònica
  • Claramunt Blanes, Josep
  • Ventura Casellas, Heura
Actualmente existe una creciente preocupación sobre la sostenibilidad del sector de la construcción debido a su gran contribución al cambio climático. Aproximadamente un tercio de las emisiones de CO2 son producidas por este sector, tanto durante la construcción como en la fase operativa de los edificios. Otro problema ambiental es la abundancia de residuos provenientes de ropa usada o de la producción de productos textiles, así como de subproductos de la agricultura. Una manera de lograr una mayor sostenibilidad es recuperar estos residuos para su uso como materia prima en materiales de construcción. Así, el uso de materiales de construcción más sostenibles y, particularmente, la reducción en la cantidad requerida de cemento es de gran interés. El objetivo principal de este proyecto se centra en desarrollar y caracterizar materiales de construcción sostenibles basados en cemento o cal mezclados con nanosilica producida a partir de subproductos de la agricultura del maíz y reforzados con telas no tejidas fabricadas con fibras recuperadas de desechos textiles, para su aplicación en paneles multifuncionales para fachadas ventiladas, pavimentos flotantes y placas para cubierta y para refuerzo de estructuras para obra de mampostería y cerámica para rehabilitación de edificios antiguos e históricos. El proyecto, financiado en el marco de la convocatoria “Retos Investigación 2019” del Ministerio de Ciencia e Innovación, se aborda desde una perspectiva interdisciplinar, que incluye paquetes de trabajo relacionados con el campo de la Ingeniería Textil e Ingeniería de Materiales y paquetes relacionados con la Ingeniería de la Construcción y Tecnología de la Edificación, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Cement composite plates reinforced with nonwoven fabrics from technical textile waste fibres: Mechanical and environmental assessment

  • Ventura Casellas, Heura
  • Álvarez del Castillo, María Dolores
  • Gónzalez López, Laura
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
In this work, we present the development and characterisation of new cement-based composite panels reinforced with fibres recovered from wastes of protective technical clothing. The developed panels present a flexural strength (~15 MPa) and fracture toughness (~3.5 kJ/m2) that are suitable for their application on ventilated façades. The environmental impact of these panels was evaluated through the life-cycle assessment (LCA) from a cradle-to-gate approach and was compared with similar engineered materials and commercial materials used for ventilated façades (fibre cement facing tiles, ceramic tiles, and natural stone plates). Two functional units were assessed: the panel necessary to cover 1 m2 of façade, and the panel necessary to cover 1 m2 of façade providing a maximum bending stress of 17 or 24 MPa. For 17 MPa, the new composite developed has presented similar environmental performance to fibre cement facing tiles and significantly better than the traditional ceramic tiles and natural stone plates, This work was supported by the Spanish AEI (Agencia Estatal de Investigación, Government of Spain) [grant number PID2019-108067RB- I00]. The author Heura Ventura is a Serra-Húnter fellow. Monica Ardanuy aknowledges the Ministerio de Universidades (Ministry of Universities, Government of Spain) for the mobility grant PRX21/00264 (Subprograma de Movilidad, Plan Estatal de Investigación Científica y Técnica y de Innovación 2017–2020), Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Characterization of cement composite plates reinforced with nonwovens obtained from technical waste fibres

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mechanical properties and durability of biobased fabric-reinforced lime composites intended for strengthening historical masonry structures

  • Rakhsh Mahpour, Ali
  • Ardanuy Raso, Mònica
  • Ventura Casellas, Heura
  • Rosell Amigó, Juan Ramón
  • Claramunt Blanes, Josep
The use of lime-based composites reinforced with fabrics made of natural fibers, is a promising solution for the strengthening of historical masonry structures owing to its moderate mechanical strength, similar color and chemical compatibility, avoiding damage on the historical structure and contributing to crack-width control. In this study, a new lime-based composite reinforced with flax nonwoven fabrics is mechanically characterized to study its reinforcement potential in terms of strength, and stress distribution. To this end, laminate plates with lime/metakaolin matrix and four to six layers of fabric reinforcement were produced and totally carbonated in a CO2 chamber. Both the mechanical (flexural and tensile) and durability (against wet-dry cycles) properties of the composite were subsequently assessed. Furthermore, Digital Image Correlation (DIC) was carried out on tensile testing to study the stress distribution. The 6-layer composites displayed the best performance (with flexural and tensile strengths of approximately 5.3 MPa and 2.5 MPa, respectively), followed by the 5-layer and the 4-layer composites. The DIC analysis revealed a higher stress distribution in the 6-layer composites, with an increased number of cracks, although having a lower severity. As for durability, a decrease of 30–45% is observed in flexural strength, and of 6–18% in tensile strength, depending on the number of reinforcing layers. SEM analysis refers to fiber/matrix debonding as the cause of this decrease. No damage has been observed on the fiber surface, which retains its reinforcing capacity. All of the composites displayed strain-hardening behavior in both the unaged and aged conditions. Study outcomes are intended to serve as the basis for the creation of a future, compatible, reliable, and sustainable system given its potential application in the historical restoration of masonry structures, The authors wish to express their gratitude to the Spanish government’s Ministerio de Ciencia e Innovación (MCIN) and Agencia Estatal de Investigación (AEI) for the financial support provided within the scope of the RECYBUILDMAT project (PID2019–108067RB-I00MICIN/ AEI/10.13039/501100011033), and the Generalitat de Catalunya’s Agència de gestió d’Ajuts Universitaris i de Recerca (AGAUR) for the financial support provided to the TECTEX Research Group (2021 SGR 01056). The author Heura Ventura is a Serra-Húnter fellow, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Preliminary study on new micro textile waste fiber reinforced cement composite

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
Large amounts of nonrenewable resources are depleted by the construction industry in addition to the generation of million tons of mineral waste and carbon dioxide gas every year. For the sake of a more sustainable consumption pattern of building materials, as well as for reducing the waste flux to landfills, the use of recycled materials and wastes should be researched and motivated. One of the promising wastes is textile waste from residues of the garments and textile industries. The recycling and reusing of textile waste would be beneficial for reducing CO2 emissions and energy intake. In this sense, there are already some studies regarding the thermal behavior of this type of material, however, the engineering design properties of textile waste fiber reinforced cement composites to identify the proper application have not been deeply investigated. Hence, the objective of this study was to evaluate the potentiality of using textile waste fiber as reinforcement in the cement paste. To this end, the composites with three different treatments were made and the optimum treatment was chosen based on the flexural test. The result is the feasibility of using this kind of fiber as reinforcement of mortar elements with dewatering treatment., This work was supported by the Spanish Government, Ministerio de Ciencia e Innovación [grant number PID2019-108067RB-I00]., Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Evaluación de residuos textiles monomateriales para el refuerzo de compuestos de base cemento

  • Oliver Ortega, Helena
  • Alvarez, Maria
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Ventura Casellas, Heura
La gestión del abundante volumen de residuos textiles, en continuo crecimiento, y sus escasas opciones de reciclaje, representan uno de los grandes retos actuales de la industria textil. Además, las futuras restricciones respecto a este residuo por parte de la Unión Europea (EU), algunas de ellas de próxima aplicación como la obligación de su recolección en el sistema municipal de residuos o las restricciones de exportación de éste, una solución largamente empleada hoy en día, provocan que sea imperativo encontrar soluciones de reciclaje para este residuo. En este contexto, el proyecto RECYBUILDMAT propone la utilización del residuo textil post-consumo, a través de telas no tejidas, como refuerzo para materiales compuestos cementícios con aplicación en paneles para fachadas ventiladas, pavimentos o elementos de mampostería. De esta forma, no solamente se recupera y aprovecha un residuo de escasa reciclabilidad, incrementándose su circularidad, sino que contribuye a la sostenibilidad de otra de las grandes industrias contaminantes como lo es la industria de la construcción, y en especial la del cemento. No obstante, y a pesar de que los materiales preparados en el marco del proyecto han demostrado su viabilidad y sostenibilidad, la durabilidad podría verse afectada debido al ataque alcalino del cemento sobre las fibras empleadas como refuerzo. Para estudiar este ataque alcalino y ver el efecto que tenía en función de la naturaleza química de las fibras, en este trabajo se estudió el efecto simulante cementíceo en telas no tejidas monomateriales de fibras de lana, algodón, viscosa, poliéster, poliamida y acrílicas. Para ello, siguiendo una aproximación al estándar UNE-EN 12467, las telas se impregnaron con un simulante cementíceo (siguiendo la norma ASTM C1897-20) y se sometieron a 25 ciclos de secado y humedad. El uso del simulante de cemento fue necesario para poder analizar el ataque químico en las fibras. Así, a pesar de que quedaban restos del simulante en la superficie de las fibras, no eran tan voluminosos como los del cemento, permitiendo observar cambios en la morfología y estructura química de las fibras, pudiéndose evaluar si existían signos de degradación. Se concluyó que las fibras químicas de polímero sintético, a diferencia de las naturales y químicas de polímero natural, no muestran ninguna degradación, como es el caso de las fibras acrílicas, o muestran alguna ligera degradación, como las fibras de poliamida o poliéster, por lo que son las mejores candidatas para ser empleadas como refuerzo en los materiales compuestos de matriz cementícia, Desde el grupo de investigación agradecer a la Agencia Estatal de Investigación por la financiación para el proyecto RECYBUILDMAT (PID2019-108067RB-100) que ha permitido desarrollar estudio, y al Departament de Recerca i Universitats de la Generalitat de Catalunya por la financiación al grupo consolidado de investigación TECTEX (2021 SGR 01056). También agradecer a Formació i Treball por proporcionar las muestras de residuo post-consumo con las que se ha elaborado este trabajo. Finalmente, por parte de la autora María Álvarez, agradecer a la Fundación Textil Algodonera y a la Asociación Industria Textil Algodón (AITPA) por reconocer este estudio con el 1r Premio de Innovación al Talento Joven 2023, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Comparing the mechanical performance of flax nonwoven fabric reinforced lime composites modified with two types of lime

  • Rakhsh Mahpour, Ali
  • Ardanuy Raso, Mònica
  • Ventura Casellas, Heura
  • Rosell Amigó, Juan Ramón
  • Claramunt Blanes, Josep
The use of more environmentally friendly materials is gaining increased acceptance in strengthening historic masonry structures. Therefore, using vegetable nonwoven fabric as reinforcement in the lime composite may be a promising solution. This study presents a comparison extensive experimental program carried out on two flax nonwoven fabric reinforced lime composites ( CL-90 and putty CL-90) modified with two kinds of various metakaolin (MK). Laminate plates comprising six layers of fabric impregnated with a lime matrix were created and cured in a CO2 chamber for up to 7 days and both the mechanical (flexural and direct tension) Further and scanning electron microscopy (SEM) was used to complement the analysis of mechanical characterization. The results confirmed that the 6 layers composites with Putty LC-90 lime had a better mechanical performance. The results and outcomes of this study may serve as the basis for future research on these composites and their potential use in structural applications in the building construction and restoration of historical masonry structures, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Effect of accelerated aging and silica fume addition on the mechanical and microstructural properties of hybrid textile waste-flax fabric-reinforced cement composites

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
Incorporating eco-friendly substances obtained from recycled resources and industrial by-products is gaining increased acceptance among building materials. In this context, a cementitious matrix containing supplementary cementitious materials (SCMs) reinforced by recycled fibers may be a promising solution from both a durability and sustainability perspective. This study presents an extensive experimental program carried out on a cement- based composite with Silica Fume (SF), reinforced with recycled textile waste (TW) nonwoven fabric. Initially, the mechanical strength (compression and flexure) of the Portland cement paste substituted with variable SF content (0%–30%) was characterized. Based on the results, laminate plates having six TW fabric layers impregnated with three different cement pastes, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A textile waste fiber-reinforced cement composite: comparison between short random fiber and textile reinforcement

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
Currently, millions of tons of textile waste from the garment and textile industries are generated worldwide each year. As a promising option in terms of sustainability, textile waste fibers could be used as internal reinforcement of cement-based composites by enhancing ductility and decreasing crack propagation. To this end, two extensive experimental programs were carried out, involving the use of either fractions of short random fibers at 6–10% by weight or nonwoven fabrics in 3–7 laminate layers in the textile waste-reinforcement of cement, and the mechanical and durability properties of the resulting composites were characterized. Flexural resistance in pre- and post-crack, toughness, and stiffness of the resulting composites were assessed in addition to unrestrained drying shrinkage testing. The results obtained from those programs were analyzed and compared to identify the optimal composite and potential applications. Based on the results of experimental analysis, the feasibility of using this textile waste composite as a potential construction material in nonstructural concrete structures such as facade cladding, raised floors, and pavements was confirmed. The optimal composite was proven to be the one reinforced with six layers of nonwoven fabric, with a flexural strength of 15.5 MPa and a toughness of 9.7 kJ/m2., This research was funded by the Spanish Ministry of Economy, Industry, and Competitiveness, RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nuevo material de construcción a partir de residuos de ropa usada

  • Ardanuy Raso, Mònica
  • Claramunt Blanes, Josep
  • Ventura Casellas, Heura
  • Oliver Ortega, Helena
El nuevo material creado por el grupo de investigación TECTEX, del Campus de Terrassa, mejora las propiedades del fibrocemento, es muy resistente, más flexible que otros materiales de construcción, es ignífugo y contribuye a reducir el impacto medioambiental en la construcción y por la destrucción de los residuos textiles, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Durability of eco-friendly strain-hardening cementitious composite incorporating recycled textile waste fabric and silica fume

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
To reach carbon neutrality, the use of more eco-friendly building materials derived from recycled resources and industrial by-products has been widely encouraged. The use of Portland cement (PC) and concrete as the most used material in the world, after water, ends in the release of million tonnes of CO2 into the atmosphere. On the other hand, fast fashion in the garment industry has resulted in a massive volume of textile waste (TW) that ends up in landfills worldwide. In this regard, a cementitious composite containing industrial by-products as a partial replacement of PC reinforced with recycled TW fibers could be a viable option in terms of both durability and sustainability. In this study, the durability of the hybrid TW/falx nonwoven fabric-reinforced cement composite modified with 30% Silica Fume (SF) was investigated by determining the effect of accelerated wet /dry cycles on the mechanical behavior (through the flexural test) and microstructural characteristics (through scanning and backscat-tered electron microscope). The results show that there was a negligible difference between the mechanical properties of the laminated composite treated with SF with respect to the one without SF in unaged conditions. Nonetheless, after accelerated aging, the fibers in the former could maintain their strength and flexibility, resulting in the composite with better post-cracking mechanical parameters by 40%. © 2022, fib. The International Federation for Structural Concrete. All rights reserved., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Cement composite panels reinforced with textile waste and flax nonwoven fabrics: flexural and accelerated aging performance

  • Sadrolodabaee, Payam
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
  • Claramunt Blanes, Josep
Towards more eco-friendly building materials, nonwoven fabrics from natural-based (flax) and recycled (textile waste) fibers were produced and incorporated into the cementitious composite panels. The textile waste fibers were recovered from two different clothing sources including fashion and fire-proofing garments. The flexural and durability (through forced wet-dry aging cycles) properties of the laminated sandwich-like cement panels reinforced with four different nonwoven fabrics (flax, treated flax, hybrid fashion textile waste/flax, and fire-proofing textile waste) were analyzed. Based on the results, all four different composites showed promising flexural-hardening behaviors in unaged conditions, especially those reinforced with the treated flax or hybrid fabrics which reached flexural strength of more than 16 MPa and energy ab-sorption index of more than 10 kJ/m2. After wet-dry aging, the post-cracking performance of all composites degraded due to fiber embrittlement, this was more evident for untreated flax composite (reduced by ~65%). Nonetheless, the treated flax fabric composite and hybrid fabric composite containing silica fume could show a better performance after aging., The authors express their gratitude to the Agencia Estatal de Investigación, Spanish Ministry of Economy, Industry, and Competitiveness (Government of Spain) for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00/AEI/10.13039/501100011033); 3D-Crete (2019PROD00066/IU68-017262-Codi project: J-02696); and CREEF (PID2019-108978RB-C32/AEI/10.13039/501100011033). The first author acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mechanical and durability characterization of a new textile waste micro-fiber reinforced cement composite for building applications

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
Fiber reinforced mortars (FRM) are growingly used in several fields of building technology (e.g., façade panels, roofing, raised floors and masonry structures) as building elements. One of the promising type of fiber for these composite materials can be textile waste originated from cloth wastes. The use of this sort of recycled materials and wastes as cement reinforcement within the building sector can play a relevant role in sustainability, both the environmental, economic and social perspectives. In this paper, the design mechanical properties (flexural and compressive strengths at 7, 28 and 56 days as well as toughness and stiffness) together with durability properties of cement pastes reinforced with short Textile Waste Fiber (TWF) in contents ranging from 6 to 10 % by weight fraction cement was investigated. The results were compared with those obtained from Kraft Pulp pine Fiber (KPF), taken as reference. The main conclusion is the feasibility of using this type of fiber as potential reinforcement in construction materials with the optimum dosage of 8%. Although the flexural resistance and toughness of the TWF composite are lower than KPF control by almost 9%, the compressive strength and stiffness together with durability properties have proven to be enhanced respect to the reference composite., The authors express their gratitude to the Spanish Ministry of Economy, Industry and Competitiveness for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Upcycling fibers from end-of-life clothes & textile remnants for sustainable building materials: closing the loop for a circular economy (Recybuildmat)

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of long-fibre content on the reinforcement capacity of nonwovens obtained from recycled textile waste for application in cement composites

  • Julián Gómez, Bárbara
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Ventura Casellas, Heura
The use of nonwoven fabrics made from recycled textile fibers as reinforcement for cement-based composites offers a synergistic solution for the textile industry and the building sector, both known for their significant environmental impacts. However, a primary limitation in the reinforcing capacity of these nonwovens is the short length of recycled fibers. To overcome this, incorporating longer virgin fibers becomes necessary, which can reduce the material's overall sustainability. Therefore, it is crucial to determine the optimal composition of nonwoven fabrics in terms of recycled short and virgin long fiber content to develop cement building materials with a strong balance of mechanical performance and sustainability. This study investigates the effect of long fiber content on the mechanical behavior of nonwovens prepared from recycled fibers, incorporating long fibers ranging from 0 % to 40 %. Nonwoven fabrics were produced using an enhanced carding and needle-punching method and subsequently characterized for their mechanical properties. Cement composite plates prepared with these nonwovens were then tested under bending and tensile forces to assess their performance. Composites reinforced with nonwovens containing 30 % and 40 % long fibers exhibited excellent flexural and tensile strength (>19 MPa and ∼4 MPa, representing increases of 37 % and 46 %, respectively) and a toughness increase exceeding 160 % compared to composites without long fibers. Digital Image Correlation (DIC) revealed more uniform crack distribution at higher long fiber content. A composition with 30 % long fibers (C30) emerged as the most suitable, offering an optimal balance between mechanical performance and a high recycled fiber content, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Serviceability parameters and social sustainability assessment of flax fabric reinforced lime-based drywall interior panels

  • Rakhsh Mahpour, Ali
  • Sadrolodabaee, Payam
  • Ardanuy Raso, Mònica
  • Haurie Ibarra, Laia
  • Lacasta Palacio, Ana María
  • Rosell Amigó, Juan Ramón
  • Claramunt Blanes, Josep
In the search of more environmentally-friendly construction materials, the use of natural-based fibers has gained much attention as reinforcement in the inorganic-based matrix. In this paper, the nonwoven flax fabric reinforced lime composites are created using a dewatering technique, and the serviceability parameters –thermal conductivity, sound absorption coefficient, and residual flexural resistance after exposure to elevated temperature– are determined experimentally. The tests are carried out on two different lime composites prepared under two distinct curing regimens, i.e., accelerated carbonation in a CO2 chamber and natural carbonation in laboratory conditions, to evaluate the effect of forced carbonation. In addition, the experimental results of the serviceability parameters are included in the MIVES model (Integrated Value Model for Sustainability Assessment) to evaluate the social sustainability of the developed material as an interior drywall panel. MIVES, a type of multi-criteria decision-making method, is based on the value function concept and seminars with experts. According to the results of experimental tests, the accelerated cured sample has higher thermal conductivity (~4 times) and lower sound absorption coefficients (~20%) than the naturally cured one. Nonetheless, the flexural performance of the former is 50% (at room temperature) and 100% (at elevated temperature) better. As for the social sustainability index assessed by the MIVES-based multi-objective approach, it ranges between 0.65 and 0.75 (out of 1.0) for both lime composite panels, at least 20% higher than the control lime panel with no reinforcement. The sustainability model designed for this research can be used for assessing the social sustainability performance of other materials although the weights assigned by the experts could be adapted to reflect the perceptions and local preferences., This work was supported through the project grants PID2019-108067RB-I00/AEI/10.13039/501100011033 and PID2020-117530RB-I00/MCIN/AEI/10.13039/501100011033 by the Ministerio de Ciencia e Innovación (MCIN)/Agencia Estatal de Investigación (AEI) of the Spanish Government. The author Payam Sadrolodabaee acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant)., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A review of the electrical conductivity test methods for conductive fabrics

  • Xie, Zeyue
  • Ventura Casellas, Heura
  • Ardanuy Raso, Mònica
With the substantial growth of the smart textiles market, electrical properties are becoming a basic requirement for most of the advanced textiles used in the development of wearable solutions and other textile-based smart applications. Depending on the textile substrate, the test method to determine the electrical properties can be different. Unlike smart fibers and yarns, the characterization of the electrical properties of fabrics cannot be tested between two connection points because the result would not represent the behavior of the entire fabric, so the electrical properties must be related to an area. The parameters used to characterize the electrical properties of the fabrics include resistance, resistivity, and conductivity. Although all of them can be used to indicate electrical performance, there are significant differences between them and different methods available for their determination, whose suitability will depend on the function and the textile substrate. This paper revises the main parameters used to characterize the electrical properties of conductive fabrics and summarizes the most common methods used to test them. It also discusses the suitability of each method according to several intervening factors, such as the type of conductive fabric (intrinsically or extrinsically conductive), its conductivity range, other fabric parameters, or the final intended application. For intrinsically conductive woven fabrics, all the methods are suitable, but depending on the requirements of conductivity accuracy, the contact resistance from the measuring system should be determined. For intrinsically conductive knitted fabrics, two-point probe, Van der Pauw, and eddy current methods are the most suitable. And for intrinsically conductive nonwoven fabrics, two-point probe and four-point probe methods are the most appropriate. In the case of extrinsically conductive fabrics, the applied method should depend on the substrate and the properties of the conductive layer., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Characterization of a textile waste nonwoven fabric reinforced cement composite for non-structural building components

  • Sadrolodabaee, Payam
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Fuente Antequera, Albert de la
Large amounts of nonrenewable resources are depleted by the construction industry in addition to the generation of million tons of mineral waste and carbon dioxide gas every year. For the sake of a more sustainable consumption pattern of building materials, as well as for reducing the waste flux to landfills, the use of recycled materials and wastes should be researched and motivated. In this sense, textile waste (TW) nonwoven fabric from residues of the garments and textile industries are investigated as internal reinforcement for cement-based matrices to enhance ductility and cracking control. To this end, an extensive experimental program was carried out to characterize both the mechanical and durability properties of the composite. The results were compared with those obtained from flax nonwoven fabric, taken as a reference (FNH and FH composites). All the composites showed a remarkable improvement in terms of toughness and post-cracking stress-bearing capacity, six being the optimum number of TW reinforcing layers. Through the analysis of the results obtained, the feasibility of using TW composite as a potential construction material in non-structural applications was confirmed. The extension to structural applications of low-medium responsibility is still required further research; nonetheless, the results are promising to this respect., The authors express their gratitude to the Spanish Ministry of Economy, Industry and Competitiveness for the financial support received under the scope of the projects RECYBUILDMAT (PID2019-108067RB-I00) and CREEF (PID2019-108978RB-C32)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Properties of phase change material impregnated vegetal nonwovens for use in cementitious composite reinforcement, Propietats de materials de canvi de fase impregnats en teixits no teixits vegetals per al seu ús com a reforç en compostos cimentosos, Propiedades de materiales de cambio de fase impregnados en no tejidos vegetales para su uso como refuerzo en compuestos cementicios

  • González Espinosa, Vanessa
  • Lacasta Palacio, Ana María
  • Ardanuy Raso, Mònica
  • Claramunt Blanes, Josep
Natural fibres offer sustainable reinforcement for composites, while the construction sector seeks materials combining thermal regulation and mechanical performance. This work investigates the little-explored direct impregnation of nonwoven flax fibres with phase change materials (PCM) for multifunctional cement composites. Two PCMs with different phase transition temperatures (21 and 28 ¿C) were evaluated. The nonwoven impregnated with 28 ¿C PCM exhibited superior performance, both in thermal and mechanical terms, and for this reason it was selected for incorporation into the cementitious composites. In addition, a comparison was carried out with a microencapsulated PCM displaying a similar transition temperature. All composite samples underwent thermal analysis and mechanical tests. Thermal performance improvements relative to the control specimens (without PCM) resulted in a significant time delay in temperature response in all cases. The nonwoven impregnated composite manufactured above the transition temperature exhibited superior mechanical performance compared with microencapsulated PCM systems. Although showing lower strength than the control specimen without PCM, its remaining flexural strength of ~7 MPa highlights its potential for non-structural applications, including roof tiles and, in specific cases, ventilated façades., Peer Reviewed, 11 - Ciutats i Comunitats Sostenibles, 12 - Producció i Consum Responsables, 13 - Acció per al Clima, 9 - Indústria, Innovació i Infraestructura, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Study of the fire and thermal behaviour of façade panels made of natural fibre-reinforced cement-based composites

  • Gónzalez López, Laura
  • Claramunt Blanes, Josep
  • Haurie Ibarra, Laia
  • Ventura Casellas, Heura
  • Ardanuy Raso, Mònica
The thermal and fire behaviour of calcium aluminate cement-based composites with a variable metakaolin content (from 0 to 40 wt% addition) reinforced with nonwoven flax fabrics has been examined. The fire behaviour was assessed using epiradiator and small-scale fire testing. The composites did not emit smoke or generate flames, nor did they produce spalling. Their integrity was maintained above 1000 ¿C. Samples having a higher metakaolin content revealed a delay in the temperature of the unexposed surface until reaching 760 ¿C. The effect of exposure to high temperatures (250 ¿C, 450 ¿C, and 950 ¿C) on bending behaviour was examined. The fibres were found to maintain their reinforcing capacity up to 250 ¿C, while the matrix maintained its performance up to 450 ¿C. The addition of metakaolin reduced conductivity and diffusivity. The results of the thermal and fire behaviour of the tested composites indicated that they may be suitable for façade panels for outdoor applications, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Flax fabric-reinforcement lime composite as a strengthening system for masonry materials: study of adhesion

  • Rakhsh Mahpour, Ali
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Rosell Amigó, Juan Ramón
The present study was designed to investigate the bond mechanism between flax nonwoven fabric reinforced lime mortars and four different types of masonry stones. The researchers carried out a comprehensive characterization of the mortars and stones, and analyzed the interface between these materials based onbondextensionandflexuralstrength.Theresultsshowedthatbondstrengthvalues were directly related to adherence extension, which was dependent on surface treatment (such as water, lime, and latex). The flexural tests conducted on stones strengthened with the flax nonwoven fabric reinforced lime composite revealed that the latex treatment showed the best performance. This study provides preliminary evidence that the use of flax nonwoven fabric reinforced lime composite maybeaneffective method for masonry strengthening. However, further research is necessary to reach a comprehensive conclusion. Further studies may include an investigation of the effects of different types of latex, the influence of curing conditions on bond strength, and the long-term performance of the strengthening system. The results of this research may have important implications for the conservation and strengthening of historic masonry structures, as well as for the design of new masonry constructions., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The effect of fibres and carbonation conditions on the mechanical properties and microstructure of lime/flax composites

  • Rakhsh Mahpour, Ali
  • Ventura Casellas, Heura
  • Ardanuy Raso, Mònica
  • Rosell Amigó, Juan Ramón
  • Claramunt Blanes, Josep
Fibre and textile-reinforced mortars are increasingly being used for a variety of building applications, including the strengthening of masonry structures. Lime mortars reinforced with sustainable fibres (such as vegetable or cellulosic fibres) may provide an interesting solution. In this paper, a mixture of commercial lime with 20% metakaolin addition was used to produce composites reinforced with non-woven flax fabrics that were cured at different moisture contents (from 0 to 100%) for 7 or 14 days in a CO2 incubator. The composites were char- acterised to determine their flexural behaviour, carbonation level and microstructure. According to the results, no differences exist in the flexural strength of the composites made in the moisture range of 33%–66%. At 7 days of curing, they attained Modulus of Rupture (MOR) values that exceeded 5.5. MPa. Moreover, it was observed that under high moisture conditions, the permeability of the fibres allows for CO2 access, despite the saturation of the pores of the matrix – allowing a reaction in the vicinity of the fibres –, while under dry conditions, the fibre’s moisture retention does not permit the carbonation of the matrix in their vicinity, even though complete carbonation takes place after 14 days, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental characterization of comfort performance parameters and multi-criteria sustainability assessment of recycled textile-reinforced cement facade cladding

  • Sadrolodabaee, Payam
  • Hosseini, Seyed Mohammad Amin
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Haurie Ibarra, Laia
  • Lacasta Palacio, Ana María
  • Fuente Antequera, Albert de la
Within the building construction sector, fiber cement boards have attracted interest as facade cladding materials in the last ten years, especially those that incorporate –for reinforcing purposes– natural and/or recycled synthetic fibers (i.e, from the textile industry). So far, the design-governing parameters of facade cladding panels have been mechanical strength, durability, constructability, aesthetics, insulation capacity, and fire resistance. From the sustainability perspective, the impact of the facade on the economic and energy efficiency performance is most often the parameter that leads the decision-making process. Within this context, the quantification of the sustainability performance of the facade –accounting for economic, environmental, and social indicators– is unfrequently carried out in design and project phases, this being attributed to the lack of methodologies that allow considering and quantifying some relevant indicators representative of the facade sustainability performance. As consequence, decisions made based on solely economic and on some of the environmental indicators might lead to solutions with lower sustainability performance than that required (or expected). Recycled textile waste fabric-reinforced cement board as a facade-cladding material for building envelopes is the focus of this research. In order to characterize the fire resistance, and thermal and acoustic insulation –as relevant serviceability parameters– of this material, an experimental program was carried out. Likewise, the sustainability performance of this facade-cladding is assessed through a method based on the Integrated Value Model for Sustainability Assessment (MIVES). This multi-criteria decision making (MCDM) model relies on the value function concept and the multi-disciplinary participation of experts to identify and quantify the relevant indicators of the facade sustainability performance and the relative importance of indicators and requirements. The MIVES-based model generated for this research can be straightforwardly used for assessing the sustainability performance of facade-cladding techniques made of any material and for any type of building (and location). The application of the MIVES model led to the sustainability index of this new material for facade-cladding ranging from 0.68 to 0.71 (/1.00) for different weighting scenarios., The authors express their gratitude to the Spanish Ministry of Economy, Industry, and Competitiveness for the financial support received under the scope of the projects CREEF (PID2019-108978RB-C32) and RECYBUILDMAT (PID2019-108067RB-I00)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

TECTEX-Grupo de investigación en tecnología textil: investigación para contribuir a la transición verde y digital de la industria textil

  • Carrera Gallissà, Enric
  • Algaba Joaquín, Inés María
  • Buscio Olivera, Valentina
  • Claramunt Blanes, Josep
  • Cano Casas, Francesc
  • Cayuela Marín, Diana
  • Ilén, Elina Emilia
  • Oliver Ortega, Helena
  • Riba Moliner, Marta
  • Tornero García, José Antonio
  • Ventura Casellas, Heura
  • Ardanuy Raso, Mònica
El grupo de investigación de ingeniería textil (TECTEX) INTEXTER y del Departamento de Ciencia e Ingeniería de Materiales de la Universitat Politècnica de Catalunya tiene como principal objetivo el desarrollo y optimización de nuevos materiales, procesos y tecnologías de la cadena de valor de la industria textil (desde la producción y caracterización de fibras y tejidos, procesos de tintura y acabado, hasta productos textiles). La finalidad de la actividad de nuestro grupo de investigación es reducir los impactos ambientales, aumentar la circularidad y optimizar los materiales, procesos y tecnologías textiles, así como desarrollar soluciones de alto valor añadido. Todo ello para contribuir a la creación de un sector textil más sostenible y competitivo. En particular, la investigación que llevamos a cabo en TECTEX se centra en contribuir a resolver los retos globales y las necesidades de competitividad industrial europea relacionadas con la transición ecológica y la transición digital, así como con el desarrollo de nuevas soluciones de alto valor añadido enfocadas principalmente al desarrollo de dispositivos y sistemas para aplicaciones biomédicas. En este artículo se presentarán los principales proyectos que actualmente estamos liderando desde nuestro grupo de investigación, como son los proyectos relacionados con la obtención de fibras naturales a partir de residuos agrícolas (HEMPQUAL), la obtención de colorantes naturales a partir de residuos agrícolas (OLIWASTEX), el reciclaje de residuos textiles por métodos mecánicos (RECYWASTEX), el desarrollo de materiales compuestos de cemento reforzados con fibras y estructuras textiles (RECYBUILDMAT), el electrohilado para aplicaciones biomédicas (ONCOFIBRAS y la aplicación del blockchain y trazabilidad a la industria textil (TRICK), Los proyectos presentados en este artículo han recibido financiación de las siguientes entidades: Gobierno de España, Agencia estatal de investigación: PID2019-108067RB-I00/ AEI/10.13039/501100011033 (proyecto RECYBUILDMAT) Gobierno de España y Unión Europea: TED2021-130611B-I00 (proyecto RECYWASTEX), financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea “NextGenerationEU”/PRTR Generalitat de Catalunya: ACE034/21/000053 (proyecto ONCOFIBRAS); 2021PROD00074 (proyecto OLIWASTEX), 2021PROD00079 (proyecto HEMPQUAL) Unión Europea: H2020-958352-TRICK (proyecto TRICK), Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Self-heating performance of conductive textile-reinforced cement-based composites

  • Xie, Zeyue
  • Claramunt Blanes, Josep
  • Ardanuy Raso, Mònica
  • Ventura Casellas, Heura
The regular distribution of conductive networks in electrically conductive cement composites (ECCC) continues to be a challenge. This study attempted to develop an ECCC with optimal mechanical, electrical, and thermal properties, combining a non-woven conductive layer (made of stainless steel and polyester fibres –SS/PES-) with five additional non-woven reinforcing layers made of recycled textile waste fibres. Four ECCC were prepared, having distinct SS fibre contents (20%, 30%, 40%, 50%) in the conductive layer. Electrical resistivity, self-heating properties, flexural behaviour, and coefficient of linear thermal expansion were assessed. In addition, the specimens having the best heating performance from each sample underwent heating stability tests. Observations confirmed that all ECCCs adhered to Ohm’s law. ECCC displayed the highest resistivity at 20% SS fibre (around 21.3 × 10- 3 O m) and the lowest resistivity at 50% SS fibre (around 4.9 × 10- 3 O m). In terms of heating performance, ECCC containing 20% SS fibre displayed the best performance despite having the highest resistivity, reaching a temperature increase of approximately 46.2 ¿C under 21 V within 30 min and maintaining a residual temperature of approximately 8.7 ¿C after 30 min of cooling. In addition, for all of the ECCC samples, the electrical and heating effects remained consistent over 20 cycles. In mechanical terms, the ECCC had Modulus of Rupture (MOR) values ranging between approximately 9 and 13 MPa. The coefficient of linear thermal expansion (CLTE) was ~13 (10- 6 /¿C). Overall, the study highlights the potential of non-woven fabric as a conductive material in ECCC, offering stable and repeatable conductive networks, noting the ECCC’s broader applications., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mechanical performance of aged cement-based matrices reinforced with recycled aramid textile nonwoven fabric: comparison with other FRCMs

  • Sadrolodabaee, Payam
  • Fuente Antequera, Albert de la
  • Ardanuy Raso, Mònica
  • Claramunt Blanes, Josep
Utilizing recycled fibers as reinforcement in cement-based matrices is an effective means of promoting waste recycling and adopting a circular economy approach in the construction industry. Within this framework, the recycling and potential reutilization of textile residues can improve the pre- and post-cracking performance of cement-based matrices intended for building components with up to intermediate structural responsibilities (i.e., panels and cladding elements for buildings). This research is focused on the mechanical and durability -through forced aging of dry-wet and freeze-thaw cycles- experimental characterization of laminated fabric-reinforced cementitious matrices (FRCMs) containing 4 and 6 nonwoven fabric layers obtained from end-of-life fire-protecting t-shirts. For this purpose, both direct and flexural tensile tests were conducted to characterize the mechanical performance of the composite. The tests on the 6-fabric layers produced panels with Portland Cement (PC) matrix, after 28-day of curing, led to average values of the maximum tensile strength of 3.7¿MPa with associated toughness index superior to 25¿kJ/m2, and mean modulus of rupture of 11.6¿MPa with a fracture energy index of 4.3¿kJ/m2. After dry-wet accelerated aging, the post-cracking performance of the developed composites decreased (on average, 40% in toughness and 11% in strength) due to fiber embrittlement. To better understand the performance of aged composites, shredded fibers recovered from protective clothing (mainly consisting of meta-aramid fibers) were immersed in the binary matrix. Accordingly, the mechanical properties of the fibers after 5 and 10 cycles of dry-wet aging were studied. Based on the results, replacing partially PC by silica fume (between 30% and 50%) was seen as a sustainable alternative to improve the performance of the aged fibers by more than 10%., The authors express their gratitude to the Agencia Estatal de Investigación, Spanish Ministry of Economy, Industry, and Competitiveness (Government of Spain) for the financial support received under the scope of the project RECYBUILDMAT (PID2019-108067RB-I00/AEI/10.13039/501100011033). Also, they acknowledge the funding of the research group TECTEX (2021 SGR 01056) from the Department de Recerca i Universitats de la Generalitat de Catalunya. The first author acknowledges the Banco Santander for the Research Scholarships (Postdoc-UPC 2022 Grant)., Peer Reviewed, Postprint (published version)