Pasar al contenido principal

DESARROLLO DE ALTERNATIVAS SOSTENIBLES A LOS EMBALAJES PLASTICOS MEDIANTE LA VALORIZACION DE BIOMATERIALES RESIDUALES RENOVABLES

PID2020-114365RB-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural properties of coated papers with cellulosic nanofibres using different metering systems and drying technologies

  • Fillat, Ursula
  • Vergara, Priscilla
  • Villar, J. C.
  • Gómez Hernández, Nuria
10 Pág., Cellulose nanofibres (CNFs) can improve the quality of cardboard packaging. This work evaluates the ability of CNFs to impart barrier properties to commercial paper used in packaging. Three CNFs were tested: mechanical (m-CNFs), by TEMPO mediated oxidation (T-CNFs) and carboxymethylated (c-CNFs). Two metering systems (wound rod and blade micrometer) were used to apply one, five and 10 layers of CNFs suspensions, and two drying methods (hot air jet and contact with a hot polished surface in a speed dryer) were evaluated. The quality of the CNFs coated papers was measured by structural (thickness, roughness and air permeance) and optical properties (gloss) and visual appearance. c-CNFs coatings obtained the lowest air permeance values, from 0.1 to 0.01 μm/Pa·s depending on the number of coating layers, and were below those of commercial starch. T-CNFs also reduced air permeance at low weights, reaching 1.1 μm/Pa·s with one layer and 0.1 when five layers were applied. Five layers of m-CNFs were needed for good results. SEM images showed good coverage at low coat weight in c-CNFs and T-CNFs, whereas m-CNFs was unable to cover the base paper. With increased layers of m-CNFs, an adequate film was formed. c-CNFs had the highest fibrillation degree and acid group content, and was the CNFs coating with most potential as a coating for paper., This work was supported by the Spanish Ministry of Science and Innovation (CTQ2017-84963-C2-2-R and PID2020-114365RB-C22) and Madrid Regional Government (RETO PROSOST S2018/EMT-4459). Morphological analysis of coated surface samples was carried out in the National Centre of Electronic Microscopy at the Complutense University of Madrid. The authors thank P. Pereira, P. Meza and P. Castellano for their contribution to the experimental work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of metering systems and drying methods on the barrier properties of paper coated with multiple layers of cellulose nanofibres

  • Gómez Hernández, Nuria
  • Vergara, Priscilla
  • Fillat, Ursula
  • Villar, J. C.
13 Pág., Developing environmentally friendly barrier coatings as an alternative to petroleum-based polymer packaging is a challenge. Cellulose nanofibres (CNF) films have exhibited great potential as water and gas barrier layers. Recycled paper was multi-layer coated with three commercial CNF (mechanical (M-CNF), TEMPO (T-CNF) and carboxymethylated (C-CNF)) using two metering systems (wound rod and blade micrometer) and two drying methods (tension-free contact drying and air drying). The coatability and rheological behaviour of the CNF suspensions were analysed. The gas, water and grease barrier properties of the CNF coated papers were determined and compared with the results of paper coated with cationic starch. The three CNF suspensions and the starch suspension were successfully coated using both metering systems. In the multi-layer coating, air drying yielded higher coat weights than contact drying, and the difference was more noticeable in M-CNF and T-CNF coated samples. A lack of uniformity observed in CNF coatings increased with the number of coating layers. M-CNF coated samples had a whitish surface with a uniform appearance, but coating was insufficiently compact to provide barrier properties. T-CNF coating exhibited a cracked surface and consequently provided no barrier properties. Drying stresses caused breakage of T-CNF coating, which could be explained by the drop in apparent viscosity at much lower rheological shear stresses in the T-CNF suspension. C-CNF showed successful coatability and provided barrier properties to paper with both metering systems and drying methods. Air permeance decreased considerably and the water wettability of the paper decreased by 60% compared to the reference paper, even with a single coating layer (about 1 g·m−2). In addition, a greaseproof paper (grease resistance >1800 s and kit no >10) was obtained with multi-layer C-CNF coating. Although water vapour permeability at 90 % RH and 20 °C decreased slightly with a single layer of CNF coating, higher amounts of CNF did not improve this parameter., This work was financial supported by the Spanish Ministry of Science and Innovation (PID2020-114365RB-C22) and Madrid Regional Government (RETO PROSOST S2018/EMT-4459). The authors would like to thank P. Pereira, P. Meza and B. Landivar for their assistance and contribution to the experimental work, as well as the grant from the RESALVALOR (319RT0575) for stay of Priscilla Vergara at the University of Coimbra., Peer reviewed