Pasar al contenido principal

MATERIALES COMPUESTOS DE FIBRA DE CARBONO BIO-INSIPIRADOS

PID2020-119003GB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SALAMANCA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of film thickness and substrate roughness on the formation of laser induced periodic surface structures in poly(ethylene terephthalate) films deposited over gold substrates

  • Prada-Rodrigo, Javier
  • Rodríguez-Beltrán, René I.
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
10 pags., 10 figs., 4 tabs., A study of the formation of Laser Induced Periodic Surface Structures (LIPSS) using near-infrared femtosecond pulsed laser irradiation on poly(ethylene terephthalate) (PET) films deposited over gold substrates has been carried out. We report the influence of the gold substrate roughness and the PET film thickness on LIPSS formation and analyze it in terms of the features of the electric field distribution obtained by computer simulations using COMSOLTM. We obtain LIPSS with periods close to the irradiation wavelength as long as the aforementioned substrate and film parameters remain below certain threshold values, in particular for polymer thicknesses below 200 nm and substrate roughness of few nm. However, experiments show the impossibility of LIPSS formation for rough substrates as well as thick films above these threshold values. In our numerical simulations, we notice the generation of Surface Plasmon Polariton (SPP) in the film-substrate interface that gives rise to a periodical field pattern on the surface of the thin film. This periodicity is broken for a certain level of substrate roughness or film thickness. Moreover, the evolution of the period of the SPP as the substrate roughness and film thickness change for given laser parameters is qualitatively in good agreement with the experimental LIPSS period (below but close to the irradiation laser wavelength). In conclusion, the experimental findings are explained by the formation and behavior of SPP in the thin film-substrate interface. On these grounds, we propose that, for our case of study, this SPP formation and the subsequent inhomogeneous rise in temperature induced by the periodic field on the surface of the sample is the leading mechanism contributing to LIPSS formation., Funding: This work was supported by the Spanish State Research Agency (AEI), Spain [project numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/501100011033, and PID2019-106125GB-I00/AEI/10.13039/501100011033] and the Junta de Castilla y León, Spain [project number SA136P20]. J.P.-R. thanks the Spanish Ministry of Universities, Spain [grant number FPU17/01859]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Physicochemical Modifications on Thin Films of Poly(Ethylene Terephthalate) and Its Nanocomposite with Expanded Graphite Nanostructured by Ultraviolet and Infrared Femtosecond Laser Irradiation

  • Rodríguez-Beltrán, René I.
  • Prada-Rodrigo, Javier
  • Crespo Solana, Ana
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
16 pags., 9 figs., 4 tabs. -- This article belongs to the Special Issue Carbon-Based Polymer Composites, In this work, the formation of laser-induced periodic surface structures (LIPSS) on the surfaces of thin films of poly(ethylene terephthalate) (PET) and PET reinforced with expanded graphite (EG) was studied. Laser irradiation was carried out by ultraviolet (265 nm) and near-infrared (795 nm) femtosecond laser pulses, and LIPSS were formed in both materials. In all cases, LIPSS had a period close to the irradiation wavelength and were formed parallel to the polarization of the laser beam, although, in the case of UV irradiation, differences in the formation range were observed due to the different thermal properties of the neat polymer in comparison to the composite. To monitor the modification of the physicochemical properties of the surfaces after irradiation as a function of the laser wavelength and of the presence of the filler, different techniques were used. Contact angle measurements were carried out using different reference liquids to measure the wettability and the solid surface free energies. The initially hydrophilic surfaces became more hydrophilic after ultraviolet irradiation, while they evolved to become hydrophobic under near-infrared laser irradiation. The values of the surface free energy components showed changes after nanostructuring, mainly in the polar component. Additionally, for UV-irradiated surfaces, adhesion, determined by the colloidal probe technique, increased, while, for NIR irradiation, adhesion decreased. Finally, nanomechanical properties were measured by the PeakForce Quantitative Nanomechanical Mapping method, obtaining maps of elastic modulus, adhesion, and deformation. The results showed an increase in the elastic modulus in the PET/EG, confirming the reinforcing action of the EG in the polymer matrix. Additionally, an increase in the elastic modulus was observed after LIPSS formation., This research was funded by the Spanish State Research Agency (AEI), grant numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/ 501100011033, PID2019-106125GB-I00/AEI/10.13039/501100011033, and Junta de Castilla y León (project number SA136P20). J.P.-R. thanks the Spanish Ministry of Universities (grant number FPU17/01859), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

BN nanosheets reinforced zirconia composites: An in-depth microstructural and mechanical study

  • Muñoz-Ferreiro, Carmen
  • Reveron, Helen
  • Rojas, T. Cristina
  • Reyes, D.F.
  • Dankic-Cottrino, Sandrine
  • Moreno, P.
  • Prada-Rodrigo, J.
  • Morales-Rodríguez, Ana
  • Chêvalier, J.
  • Gallardo-López, A.
  • Poyato, Rosalía
This paper deals with the effect of hydroxylated boron nitride nanosheets (BNNS) incorporation on the microstructural and mechanical features of zirconia ceramics. Few-layered BNNS were synthesized via a simple hydroxide-assisted planetary ball milling exfoliation technique. 3 mol% yttria tetragonal zirconia polycrystal (3Y-TZP) with 2.5 vol% BNNS powders were prepared by an environmentally friendly process in water, and spark-plasma sintered at three temperatures to explore the in-situ reduction of the functionalized BNNS. An exhaustive study by (S)TEM techniques was performed to elucidate the influence of the sintering temperature on the matrix and the 3Y-TZP/BNNS interfaces, revealing that BNNS were homogeneously distributed throughout the matrix with an abrupt transition at 3Y-TZP/BNNS interfaces. BNNS effectively hindered slow crack growth, thus increasing the composite's crack growth resistance by about 30 %. A 1 MPa·m rising R-curve was also induced by crack bridging., This research was supported by projects PGC2018–101377-B-100 and PID2022–140191NB-I0 funded by MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación, Spanish Government, Agencia Estatal de Investigación) and by ERDF (European Regional Development Funding) “A way of making Europe”, and by project P20_01024 (Junta de Andalucía/FEDER, UE 2014–2020). C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US (Plan Propio Universidad de Sevilla, Spain) fellowship through the contract USE-18740-H. Daniel F. Reyes would like to thank the University of Cádiz and the Ministry of Universities for the award of the grant “Recualificación del Profesorado” (UCA/R155REC/2021), funded by the Ministry of Universities of the Spanish Government through the European Recovery Instrument (Order UNI/551/2021). We would also like to thank the central services of the University of Cádiz (DME-SC-ICyT-ELECMI-UCA) for the support offered to obtain the TEM measurements. P. Moreno and J. Prada-Rodrigo also acknowledge the support of Ministerio de Ciencia e Innovación (PID2020-119003GB-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Boron nitride nanosheets as an effective strategy against the slow crack growth and hydrothermal ageing in zirconia composites

  • Muñoz-Ferreiro, C.
  • Morales-Rodríguez, A.
  • Reveron, H.
  • Guisado-Arenas, E.
  • Dankic-Cottrino, Sandrine
  • Moreno, Pablo
  • Prada-Rodrigo, J.
  • Chêvalier, Jérôme
  • Gallardo-López, Ángela
  • Poyato, R.
This paper explores the effectiveness of boron nitride nanosheets in preventing the premature failure of yttria-stabilized tetragonal zirconia ceramics, particularly in humid environments. A simple, low-cost and scalable technique -shear exfoliation in a kitchen blender- was used to prepare BNNS, and pure zirconia and composites with 1, 2.5 and 5 vol. % BNNS were spark plasma sintered. Accelerated hydrothermal ageing experiments in autoclave revealed a remarkable improvement of low temperature degradation resistance in all the composites. Fracture toughness and slow crack growth of the composites with 1 and 2.5 vol. % BNNS were evaluated by bending tests performed in notched specimens. Although the composites presented fracture toughness values similar to those of the reference zirconia, an increase of ∼18 % on crack-tip toughness was achieved. Similar R-curves evaluated in air and in oil-impregnated 2.5 vol. % BNNS composites revealed a limitation of stress-assisted corrosion by water in zirconia, thanks to the BNNS incorporation., This research was supported by projects PID2022–140191NB-I00 and PID2020–119003GB-I00 funded by MCIN/AEI/ 10.13039/ 501100011033 and by FEDER, UE. C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US (Plan Propio Universidad de Sevilla, Spain) fellowship through the contract USE-18740-H. The authors are grateful to the JECS Trust for funding the visit of C. Muñoz-Ferreiro to MATEIS Laboratory (INSA Lyon) (Contract No. 2020248). The authors thank Prof. J.S. Blázquez (University of Seville) for his advice and assistance regarding the KJMA model., Peer reviewed