Pasar al contenido principal

CONTROL Y MODIFICACION DE LA MATERIA EN LA NANOESCALA CON TECNOLOGIAS AVANZADAS BASADAS EN LUZ

PID2019-106125GB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optical diagnostics of gold plasmas produced by infrared laser ablation

  • Oujja, Mohamed
  • Camacho, J.J.
  • Sanz, Mikel
  • Castillejo, Marta
  • de Nalda, R.
10 pags., 8 figs., 1 tab., Laser plasmas produced by ablation of a gold target in a vacuum are spatially and temporally characterized by optical emission spectroscopy. A Nd:YAG laser (1064 nm, pulse width 15 ns and fluences of 5.8 and 11 J/cm) is used to ablate the Au target. Au, Au and Auspecies were studied both as a function of the location from the target surface and of the time delay from the laser pulse arrival. Plasma temperature, electron density and average velocities were measured from the spatiotemporal analysis. The results show a faster decay of the continuum emission, Au and Au species than in the case of neutral Au atoms. Higher velocities and a narrower temporal distribution of Au ions are observed when compared to Au atoms. Electron temperature was evaluated from the comparison of Au atomic-Boltzmann local thermodynamic equilibrium spectra with experimental ones at various delay times from the laser pulse incidence. Electron densities and electron temperatures approximately decrease from 2.3 to 1.1 × 10 cm and from 1.6 to 0.4 eV, respectively, as the delay time increases along the first 2 µs of plasma evolution., This research was supported by the Spanish State Research Agency (AEI) and the European Regional Development (FEDER) through Projects CTQ2016-75880-P-AEI/FEDER, PID2019-104124RB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033; the European H2020 IPERION HS Project (Integrated Platform for the European Research Infrastructure ON Heritage Science) (GA 871034, WP5); TOP Heritage-CM (S2018/NMT-4372) project from the Community of Madrid and with the support of Plataforma Temática Interdisciplinar of CSIC “Patrimonio Abierto: Investigación y Sociedad” (PTI-PAIS). M. O. thanks CSIC for contract.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spatiotemporally resolved optical emission spectroscopy and harmonic generation in Cu plasmas

  • Oujja, Mohamed
  • Camacho, J.J.
  • Sanz, Mikel
  • López-Quintas, Ignacio
  • Castillejo, Marta
  • de Nalda, R.
9 pags., 6 figs., Laser-induced ablation plasmas of Cu generated by nanosecond 1064 nm pulses have been examined as media for third harmonic generation of a nanosecond driving pulse. A narrow window of ablation fluences where third harmonic generation is optimized has been identified in a region around twice the ablation threshold. A detailed analysis of the features of the Cu plasma across this critical fluence window, through spatially and temporally resolved optical emission spectroscopy, has been used to assess critical plasma parameters such as temperature, electron density, and abundance of Cu species in different ionization stages. This description has been correlated with the conditions for optimum low-order harmonic generation in the Cu plasma., This research was supported by the Spanish Agencia Estatal de Investigaci on (AEI) and the European Regional Development (FEDER) through Projects CTQ2016-75880-P-AEI/FEDER, PID2019-106125GB- I00/AEI/10.13039/501100011033 and PID2019-104124RB-I00/AEI/ 10.13039/501100011033 and by Community of Madrid by project TOP Heritage-CM (S2018/NMT-4372). M. O. thanks CSIC for contract.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photoinduced Resist-free Imprinting (PRI) in fullerene thin films as revealed by Grazing Incidence Small-angle X-ray scattering

  • Gutiérrez-Fernández, Edgar
  • Rodríguez-Rodríguez, Álvaro
  • García-Gutiérrez, Mari Cruz
  • Nogales, Aurora
  • Rebollar, Esther
  • Solano, Eduardo
  • Ezquerra, Tiberio A.
9 pags., 9 figs., In this article we explore the potential of synchrotron Grazing Incidence Small Angle X-ray Scattering (GISAXS) to evaluate the extension of a Photoinduced Resist-free Imprinting (PRI) effect for grating-like Laser Induced Periodic Surface Structures (LIPSS) on spin-coated thin films of the fullerene derivative [6,6]-phenyl C-butyric acid methyl ester (PCBM). Valuable information about the nature of both the original fullerene LIPSS and of the remaining resist-free nanostructure in terms of geometry, size distribution, lattice periodicity and degree of order can be achieved by simulations of the GISAXS patterns. One of the most interesting features provided by the GISAXS analysis is the estimation of the paracrystalline distortion factor, which can be useful to evaluate the level of order in the nanostructure. Data revealed that LIPSS in PCBM films can be described as one-dimensional paracrystalline lattices with levels of order in accordance with those typically observed in LIPSS of other materials. The PRI effect leaves a qualitatively similar nanostructure but about two times more disordered than the original LIPSS one. Our results show that GISAXS is a powerful tool to characterize Resist-free Imprinting procedures of potential relevance in nanotechnology., This work has been supported by Spanish State Research Agency (AEI) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033. The GISAXS experiments were performed at NCD-SWEET beamline at ALBA synchrotron with the collaboration of ALBA staff.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photophysical and structural modulation of poly(3-hexylthiophene) nanoparticles via surfactant-polymer interaction

  • Gutiérrez-Fernández, Edgar
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
  • Cui, Jing
  • Marina, Sara
  • Martín, Jaime
  • Nogales, Aurora
9 pags., 8 figs., The optical properties of poly(3-hexylthiophene-2,5-diyl) (P3HT) can be controlled by processing the polymer in the form of nanoparticles dispersed in aqueous mediums. Colloids of P3HT were prepared by two different methods: flash –or reprecipitation- and miniemulsion precipitation technique, which result in the latter case in a polymer-water system whose stability is mediated by an ionic surfactant. Both systems yield different color dispersions, thus different absorption spectra, that is explained to be caused by the influence of the surfactant on the structure of P3HT. Differential scanning calorimetry and synchrotron radiation X-ray diffraction experiments reveal the origin of these optical differences, showing evidences of the formation of a blended structure formed due to the interaction between P3HT and the ionic surfactant. This work evidences the potential use of techniques for preparing nanoparticles in water dispersions as a tool to manipulate the structure and thus, the optical properties of these materials., This work has been supported by the Spanish Ministry of Science and Innovation under the projects PID2019-107514 GB-I00/AEI/10.13039/ 501100011033 and PID2019-106125 GB- I00/AEI/10.13039/ 501100011033, and Garantía Juvenil/Fondo Europeo. We thank E. Solano for assistance and support during beamtime in ALBA. J.M. thanks MCIU for the Ramon y Cajal contract and the grant Ref. PGC2018- 094620-A-I00 and Ikerbasque Foundation for the Fellow program
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Femtosecond XUV-IR induced photodynamics in the methyl iodide cation

  • Murillo-Sánchez, M. L.
  • Reitsma, Geert
  • Poullain, S. M.
  • Fernández-Milán, Pedro
  • González-Vázquez, J.
  • de Nalda, R.
  • Martín, Fernando
  • Vrakking, Marc J.J.
  • Kornilov, Oleg
  • Bañares, Luis
12 pags., 7 figs., 1 tab., The time-resolved photodynamics of the methyl iodide cation (CH3I+) are investigated by means of femtosecond XUV-IR pump-probe spectroscopy. A time-delay-compensated XUV monochromator is employed to isolate a specific harmonic, the 9th harmonic of the fundamental 800 nm (13.95 eV, 88.89 nm), which is used as a pump pulse to prepare the cation in several electronic states. A time-delayed IR probe pulse is used to probe the dissociative dynamics on the first excited state potential energy surface. Photoelectrons and photofragment ions - and I+ - are detected by velocity map imaging. The experimental results are complemented with high level ab initio calculations for the potential energy curves of the electronic states of CH3I+ as well as with full dimension on-the-fly trajectory calculations on the first electronically excited state, considering the presence of the IR pulse. The and I+ pump-probe transients reflect the role of the IR pulse in controlling the photodynamics of CH3I+ in the state, mainly through the coupling to the ground state and to the excited state manifold. Oscillatory features are observed and attributed to a vibrational wave packet prepared in the state. The IR probe pulse induces a coupling between electronic states leading to a slow depletion of fragments after the cation is transferred to the ground states and an enhancement of I+ fragments by absorption of IR photons yielding dissociative photoionization., MLMS acknowledges financial support through a predoctoral contract from Universidad Complutense de Madrid (Spain) and FULMATEN-CM project funded by Madrid Regional Government under programme Y2018/NMT-5028. GR thanks the Netherlands Organization for Scientific Research (NWO) for financial support (Rubicon 68-50-1410). This project has received funding (SMP) from the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Sklodowska-Curie Grant agreement No. 842539 (ATTO-CONTROL) and has been financed in part by the Spanish State Research Agency (AEI/10.13039/501100011033), Grants PGC2018-096444-B-I00, PID2019-106125GB-I00 and PID2019-106732GB-I00, and the Madrid Regional Government through the program Proyectos Sin´ergicos de I + D (Grant Y2018/NMT-5028 FULMATEN-CM). FM acknowledges support from the ‘Severo Ochoa’ Programme for Centres of Excellence in R & D (SEV-2016-0686) and the ‘María de Maeztu’ Programme for Units of Excellence in R & D (CEX2018-000805-M). All calculations were performed at the Mare Nostrum Supercomputer of the Red Española de Supercomputacion (BSC-RES) and the Centro de Computaci ´ on´ Científica de la Universidad Autonoma de Madrid (CCC-UAM). MV and OK acknowledge the support ´ from the Deutsche Forschungsgeminschaft (KO 4920/1-1). This work was performed in the Max Born Institut (Berlin) in the kHz Laboratory and received financial support from LaserLab Europe through the MBI002239 project.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructural organization of thin films prepared by sequential dip-coating deposition of poly(butylene succinate), poly(ε-caprolactone) and their copolyesters (PBS-ran-PCL)

  • Peñas, Mario I.
  • Ocando, C.
  • Penott-Chang, E.
  • Safari, Maryam
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
  • Nogales, Aurora
  • Hernández, Rebeca
  • Müller, A.J.
10 pags., 7 figs., 2 tabs., In this work, we prepare and characterize multiphasic thin films containing poly(ε-caprolactone), PCL, poly(butylene succinate), PBS, and a poly (butylene succinate-ran-ϵ-caprolactone) (PBS-ran-PCL) random copolyester. To that aim, thin films were prepared by sequential dipping of a silicon substrate into chloroform solutions of the respective polymers. The preparation method resulted in films with varying compositions of PCL and PBS components depending on the initial concentration of the dipping solutions and the number of dipping steps employed for the preparation of the samples. Atomic force microscopy (AFM), grazing incidence X-ray scattering at wide angle (GIWAXS) and scattering-type scanning near-field optical microscopy (s-SNOM) and Fourier transform infrared nanospectroscopy (nano-FTIR) were employed to characterize the films obtained. As chloroform can dissolve all components, the final composition of the film was always rich in the last deposited layer component. The thin films obtained were semicrystalline with a complex axialitic or dendritic morphology of the dominant component (that one deposited last) with traces of the other components, whose presence and location was revealed by s-SNOM/nano-FTIR., This study was supported by Spanish Ministry of Science, Innovation and Universities (MAT2017- 83014-C2-1-P, MAT2017-83014-C2-2-P, PID2019-107514 GB-I00/AEI/ 10.13039/501100011033 and PID2019-106125 GB-I00/AEI/ 10.13039/501100011033). We also acknowledge funding by Basque Government through grant IT1309-19. The authors acknowledge beamtime access at ALBA BL11 via proposal 2018072905 and the assistance of JC Martinez during the measurements. We would also like to thank the financial support provided by the BIODEST project; this project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 778092. CO wants to acknowledge “Diputaci on Foral de Gipuzkoa” in the framework program “Fellows Gipuzkoa de Atracci ́on y Retenci ́on de Talento”. RH is member of the Interdisci-plinary Platform for Sustainable Plastics towards a Circular Economy (SusPlast) from the Spanish National Research Council (CSIC).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Emission characteristics and dynamics of neutral, ionic and molecular species in a laser produced CaF2 plasma

  • Oujja, Mohamed
  • Camacho, J.J.
  • Paradela, D.
  • Castillejo, Marta
  • de Nalda, R.
15 pags., 12 figs., The emission characteristics of a laser-ablated calcium fluoride CaF plasma have been investigated using time and space optical emission spectroscopy. The plasma-plume was produced by focusing 266 nm, 15 ns pulses from a Nd: YAG laser on a calcium fluoride crystal substrate placed in a vacuum chamber. The emission observed in the plasma region is due to electronic relaxation of excited neutral Ca and F, ionic fragments Ca, Ca and F and molecular features of CaF (AΠ- XΣ, BΣ- XΣ and CΠ- XΣ) band systems. Plasma species were analyzed both as a function of the delay from the laser pulse incidence and location from the target surface. Spectroscopic diagnostics were employed to estimate time-resolved electron densities, electron temperatures and velocity expansion of different species. The results show a faster decay of the continuum emission, ionic F, Ca, Ca, F species than in the case of neutral Ca atoms and molecular species of CaF. Different excitation temperatures were measured by comparing Ca and F atomic/ionic Saha-local thermodynamic equilibrium (LTE) spectra with experimental ones at various delay times after the ablation event. Vibrational temperatures of CaF were assessed from the temporal analysis of the AΠ - XΣ Δv = 0 band sequence molecular emission. We observed a non-equilibrium plasma although the plasma is found to maintain partial LTE., This research was supported by the Spanish State Research Agency (AEI) and the European Regional Development (FEDER) through Projects PID2019-104124RB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033; the European H2020 IPERION HS Project (Integrated Platform for the European Research Infrastructure ON Heritage Science (GA 871034, WP5)); TOP Heritage-CM (S2018/NMT-4372) project from the Community of Madrid and with the support of Plataforma Temática Interdisciplinar of CSIC “Patrimonio Abierto: Investigación y Sociedad” (PTI-PAIS).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Generation of multiple triplet states in an orthogonal bodipy dimer: a breakthrough spectroscopic and theoretical approach†

  • García-Moreno, I.
  • Postils, V.
  • Rebollar, Esther
  • Ortiz, María J.
  • Agarrabeitia, A.R.
  • Casanova, David
10 pags., 9 figs., Generation of triplet states in assemblies of organic chromophores is extremely appealing for their potential use in optoelectronic applications. In this work, we investigate the intricacies of triplet state generation in an orthogonal BODIPY dimer by combining delayed photoemission techniques with electronic structure calculations. Our analysis provides a deep understanding of the electronic states involved, and describes different competing deactivation channels beyond prompt radiative decay. In particular, we identify charge-transfer (CT) mediated intersystem crossing (ISC) as the most likely mechanism for the triplet state generation in this system. The different emission bands at long times can be associated with delayed fluorescence, CT emission and phosphorescence from multiple low-energy triplets. Interestingly, the dependence of the yield of triplet state population and emission profiles with the solvent polarity evidences the decisive role of the CT configuration in the fate of the photoactivated dimer, controlling the relative ISC, reverse ISC, and internal conversion efficiencies. Overall, the present results provide a rather complete description of the delayed photophysics in the BODIPY dimer, but are not able to fully rationalize the unexpected photoluminescence recorded at long wavelengths (≥ 900 nm). We hypothesize that the origin of this emission, not present in BODIPY monomers, emerges from intermonomer interactions triggered by intramolecular distortions opening up a new vision in the controverted mechanism driving the photophysical behavior from orthogonally linked organic monomers., This work was supported by the Spanish Ministerio de Ciencia e Innovacion (Projects PID2019-106125GB-I00/AEI/10.13039/ 501100011033, PID2020-114755GB-C31, PID2020-114755GB-C32 and PID2019-109555GB-I00) and the Eusko Jaurlaritza (project PIBA19-0004). V. P. also thanks Euskal Herriko Unibertsitatea (UPV/EHU) for the ESPDOC18/85 post-doctoral grant. The authors are thankful for the technical and human support provided by the Donostia International Physics Center (DIPC) Computer Center.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Probing structure development in Poly(vinylidene Fluoride) during “operando” 3-D printing by small and wide angle X-ray scattering

  • Ezquerra, Tiberio A.
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Rebollar, Esther
  • Gálvez, Óscar
  • Šics, Igors
  • Malfois, Marc
12 pags., 8 figs., We have investigated the crystallization of the thermoplastic polymer Poly(vinylidene Fluoride) (PVDF) during “operando” 3D printing Fused Filament Fabrication (FFF). The performance of the 3D printing set-up and the corresponding methodology for performing simultaneous SAXS/WAXS with synchrotron radiation have been discussed. Simultaneous SAXS and WAXS experiments were performed across the printed line with a resolution of 50 μm. The experiments indicate that crystallization is faster at the polymer-air interface than in other points within the printed line. The final crystallinity varies with position being lower at both the interfaces, i.e. polymer-air (13%) and welding zone (11%), while being higher (18%) in the middle part of the printed line. Orientation of the crystalline lamellae is higher at both interfaces, suggesting higher shear rate than in the bulk of the printed line where elongational flow is dominant. The final crystallinity levels in the different locations of the printed line are relatively low, as compared with reported values in melt pressed samples (≈30%), due to the extremely fast crystallization kinetics involved in the solidification of PVDF 3D printed lines. Therefore, it is expected that 3D printed PVDF pieces will exhibit significant structural modifications due to the potential crystallization that eventually will proceed during storage because the glass transition of PVDF is well below room temperature., This work has been supported by Agencia Estatal de Investigación(AEI) through projects: PID2019 - 107514 GB - I00/AEI/10.13039/501100011033 and PID2019 - 106125 GB -I00/AEI/10.13039/501100011033. The experiments with synchrotron radiation were performed at NCD-SWEET beamline at ALBA Synchrotron with the collaboration of ALBA staff (Proposal 2020024176).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of smooth amorphous thin films of silicon carbide with controlled properties through pulsed laser deposition

  • Oujja, Mohamed
  • Tabakkouht, K.
  • Sanz, Mikel
  • Rebollar, Esther
  • Sánchez-Arenillas, M.
  • Marco, J.F.
  • Castillejo, Marta
  • de Nalda, R.
10 pags., 5 figs., 1 tab., Thin films of silicon carbide (SiC) on Si (100) and SrTiO (100) substrates have been grown by nanosecond pulsed laser deposition (PLD) with a Q-switched Nd:YAG laser operating at the wavelengths of 1064, 532 and 266 nm. The deposits obtained consisted of smooth and uniform layers of amorphous SiC, free of holes and cracks, with thicknesses in the range of 30–100 nm and average roughness substantially lower than 1 nm. The role of laser wavelength and of substrate temperature (300 K vs. 1025 K) on morphology, crystallinity and composition of the deposits was assessed. The films were analyzed by X-ray diffraction, micro-Raman spectroscopy and X-ray photoelectron spectroscopy. In addition, optical emission spectroscopy was employed to evaluate the characteristics of the ablation plasma and its correlation with the film growth., This research was supported by the Spanish State Research Agency (AEI) and European Regional Development (FEDER) through Projects PID2019-106125GB-I00/AEI/0.13039/501100011033 and PID2019-104124RB-I00/AEI/0.13039/501100011033. Thanks are given to the Soft and Polymeric Matter group (IEM-CSIC) for the use of AFM. We are grateful to M. Furió from MNCN-CSIC and P. Gonzalez from ICTP-CSIC for Raman and X-ray difraction technical assistance, respectively. Funding Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystallization and phase separation in PEDOT:PSS/PEO blend thin films: Influence on mechanical and electrical properties at the nanoscale

  • Sanviti, Matteo
  • Martínez-Tong, Daniel E.
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • García-Gutiérrez, Mari Cruz
Thin films of polymeric blends composed of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and polyethylene oxide (PEO) were investigated by varying the concentration of the two components over the entire range of compositions and the molecular weight of PEO. Phase separation and crystallization have been studied at different length scales by combining Atomic Force Microscopy (AFM) and Grazing Incidence Wide Angle X-ray Scattering (GIWAXS) using synchrotron light. Several different arrangements in the thin films of the two polymers constituting the blend were observed and discussed in detail, providing information about their reciprocal influence at the micro- and nano-scale. In addition to that, we were able to estimate quantitative nanomechanical and nanoelectrical properties via AFM and finally revealing the dependence of the thin films' physical properties on their composition and structure. By varying the blend composition, we achieved different coating capability, mechanical properties, and electrical conductivity. Furthermore, depending on the PEO molecular weight, the electrical response of the resulting blends’ thin films shows some differences. In the low range concentration, the blend thin films with high molecular weight PEO present coarser conducting paths than in those with the low molecular weight counterparts. For intermediate concentrations, a more effective phase segregation of PEDOT:PSS and PEO is achieved for high molecular weight PEO. These differences are also translated to different electrical conductivity., We acknowledge funding from the Spanish State Research Agency (AEI) through projects PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033. We also acknowledge funding from Eusko Jaurlaritza (Basque Government) through the Grants IT-1566-22., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of polar phases in ferroelectric poly(vinylidene fluoride) (PVDF) nanoparticles

  • Gutiérrez-Fernández, Edgar
  • Sena-Fernández, Jose
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • Hermoso-Pinilla, Francisco J.
  • Sanz, Mikel
  • Gálvez, Óscar
  • Nogales, Aurora
7 pags., 6 figs., Ferroelectric polymer nanoparticles of poly(vinylidene fluoride) (PVDF) were prepared by dialysis nanoprecipitation. Particles with mean diameter of 230 nm show piezoelectric response as observed by Piezoresponse Force Microscopy (PFM). The origin of this ferroelectric behavior has been attributed to the presence of ferroelectrically active crystalline phases of PVDF in the nanoparticles (mainly β and γ phases) as demonstrated by differential scanning calorimetry (DSC) and temperature dependent Fourier transform infrared spectroscopy (FTIR) and X ray diffraction. The combination of the preparation method and temperature treatment can provide a method for tuning the ferroelectricity in PVDF homopolymer nanoparticles., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MICINN) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033. Also, ‘Programa Operativo de Empleo Juvenil’ (YEI) Comunidad de Madrid (CAM, PEJ-2019-AI/TIC-15699). The synchrotron experiments were performed at NCD-SWEET beamline at ALBA Synchrotron with the collaboration of ALBA staff., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of film thickness and substrate roughness on the formation of laser induced periodic surface structures in poly(ethylene terephthalate) films deposited over gold substrates

  • Prada-Rodrigo, Javier
  • Rodríguez-Beltrán, René I.
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
10 pags., 10 figs., 4 tabs., A study of the formation of Laser Induced Periodic Surface Structures (LIPSS) using near-infrared femtosecond pulsed laser irradiation on poly(ethylene terephthalate) (PET) films deposited over gold substrates has been carried out. We report the influence of the gold substrate roughness and the PET film thickness on LIPSS formation and analyze it in terms of the features of the electric field distribution obtained by computer simulations using COMSOLTM. We obtain LIPSS with periods close to the irradiation wavelength as long as the aforementioned substrate and film parameters remain below certain threshold values, in particular for polymer thicknesses below 200 nm and substrate roughness of few nm. However, experiments show the impossibility of LIPSS formation for rough substrates as well as thick films above these threshold values. In our numerical simulations, we notice the generation of Surface Plasmon Polariton (SPP) in the film-substrate interface that gives rise to a periodical field pattern on the surface of the thin film. This periodicity is broken for a certain level of substrate roughness or film thickness. Moreover, the evolution of the period of the SPP as the substrate roughness and film thickness change for given laser parameters is qualitatively in good agreement with the experimental LIPSS period (below but close to the irradiation laser wavelength). In conclusion, the experimental findings are explained by the formation and behavior of SPP in the thin film-substrate interface. On these grounds, we propose that, for our case of study, this SPP formation and the subsequent inhomogeneous rise in temperature induced by the periodic field on the surface of the sample is the leading mechanism contributing to LIPSS formation., Funding: This work was supported by the Spanish State Research Agency (AEI), Spain [project numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/501100011033, and PID2019-106125GB-I00/AEI/10.13039/501100011033] and the Junta de Castilla y León, Spain [project number SA136P20]. J.P.-R. thanks the Spanish Ministry of Universities, Spain [grant number FPU17/01859]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Physicochemical Modifications on Thin Films of Poly(Ethylene Terephthalate) and Its Nanocomposite with Expanded Graphite Nanostructured by Ultraviolet and Infrared Femtosecond Laser Irradiation

  • Rodríguez-Beltrán, René I.
  • Prada-Rodrigo, Javier
  • Crespo Solana, Ana
  • Ezquerra, Tiberio A.
  • Moreno, Pablo
  • Rebollar, Esther
16 pags., 9 figs., 4 tabs. -- This article belongs to the Special Issue Carbon-Based Polymer Composites, In this work, the formation of laser-induced periodic surface structures (LIPSS) on the surfaces of thin films of poly(ethylene terephthalate) (PET) and PET reinforced with expanded graphite (EG) was studied. Laser irradiation was carried out by ultraviolet (265 nm) and near-infrared (795 nm) femtosecond laser pulses, and LIPSS were formed in both materials. In all cases, LIPSS had a period close to the irradiation wavelength and were formed parallel to the polarization of the laser beam, although, in the case of UV irradiation, differences in the formation range were observed due to the different thermal properties of the neat polymer in comparison to the composite. To monitor the modification of the physicochemical properties of the surfaces after irradiation as a function of the laser wavelength and of the presence of the filler, different techniques were used. Contact angle measurements were carried out using different reference liquids to measure the wettability and the solid surface free energies. The initially hydrophilic surfaces became more hydrophilic after ultraviolet irradiation, while they evolved to become hydrophobic under near-infrared laser irradiation. The values of the surface free energy components showed changes after nanostructuring, mainly in the polar component. Additionally, for UV-irradiated surfaces, adhesion, determined by the colloidal probe technique, increased, while, for NIR irradiation, adhesion decreased. Finally, nanomechanical properties were measured by the PeakForce Quantitative Nanomechanical Mapping method, obtaining maps of elastic modulus, adhesion, and deformation. The results showed an increase in the elastic modulus in the PET/EG, confirming the reinforcing action of the EG in the polymer matrix. Additionally, an increase in the elastic modulus was observed after LIPSS formation., This research was funded by the Spanish State Research Agency (AEI), grant numbers PID2020-119003GB-I00/MCIN/AEI/10.13039/501100011033, PID2019-107514GB-I00/AEI/10.13039/ 501100011033, PID2019-106125GB-I00/AEI/10.13039/501100011033, and Junta de Castilla y León (project number SA136P20). J.P.-R. thanks the Spanish Ministry of Universities (grant number FPU17/01859), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Inter and intra molecular dynamics in poly(trimethylene 2,5-furanoate) as revealed by infrared and Broadband Dielectric Spectroscopies

  • Gálvez, Óscar
  • Toledano, Óscar
  • Hermoso, Francisco Javier
  • Linares, Amelia
  • Sanz, Mikel
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Santoro, Gonzalo
  • Irska, Izabela
  • Paszkiewicz, Sandra
  • Szymczyk, Anna
  • Ezquerra, Tiberio A.
9 pags., 9 figs., 2 tabs., Infrared spectroscopy (IR) and Broadband Dielectric Spectroscopy (BDS) experiments have been performed in poly(trimethylene 2,5-furanoate)(PTF) and poly(trimethylene terephthalate)(PTT) below their glass transition temperatures. The BDS experiments reveal a richer inter-molecular dynamic for PTT as characterized by a multimodal β relaxation in contrast with the monomodal one exhibited by PTF. The evolution with temperature of comparable IR absorption bands is very similar for PTF and PTT and shows small shifts in wavenumbers towards lower values, with exception of the band related to the stretching mode of the carbonyl group. In addition, a significant difference appears in the shape of the bands associated with the –C[dbnd]O stretching. While for PTT the absorption feature is comprised of a single component, that for PTF exhibits several components suggesting the presence of hydrogen bonds. This effect may be responsible for the monomodal shape of the β relaxation of PTF since a higher degree of intramolecular coupling between the furan ring and the rest of the monomer is expected. Density Functional Theory (DFT) calculations support the experimental results revealing that as temperature increases an increment of the syn conformations of the 2,5-furandicarboxylic acid (FDCA) moiety is likely to occur in the amorphous state. The energy gain from more stable anti to less stable syn isomers can be compensated by the formation of hydrogen bonds between interchain FDCA moieties in syn conformations. This effect may cause additional hindrance to the intermolecular dynamics of the dielectric β relaxation. It is conceivable that the hindrance exhibited by PTF in both intra and inter-molecular dynamics may play a role in the reduction of gas diffusion and permeability of PTF in comparison with PTT., Grants PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033 funded by MCIN/AEI/10.13039/501100011033 and by “ ERDF A way of making Europe”. GS acknowledges grant RYC2020-029810-I funded by MCIN/ AEI/10.13039/501100011033 and by “ ESF Investing in your future”. SP would like to thank for financial support from the National Science Centre within project SONATA no 2018/31/D/ST8/00792. A
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D Printing-Assisted Nanoimprint Lithography of Polymers

  • Martínez-García, Patricia
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Sena-Fernández, Jose
  • Ezquerra, Tiberio A.
5 pags., 7 figs., Fused filament fabrication, commonly referred to as 3D printing, is an additive manufacturing method finding plenty of applications nowadays. In contrast, polymer nanopatterning by nanolithographic techniques plays an important role in obtaining functional surfaces and coatings for applications in different fields including micro- and nanoelectronics. In spite of their relevance, additive manufacturing and polymer nanolithography have not found yet a common niche to be developed. Although both approaches are oriented to achieve different types of objects, it is shown that the confluence of both technologies can be desirable and potentially convenient. Herein, it is demonstrated that by employing conventional 3D printing, it is possible to fabricate nanostructured polymer surfaces in a relatively simple way by using similar approaches as those used in nanoimprint lithography but without the need for clean room conditions. To do that, a printed-assisted nanoimprint lithography concept (3DPrANIL) has been tested for different types of polymer and silicon templates. It is demonstrated that a polymeric nanostructured hydrophilic template can be replicated accurately on another polymer rendering a nanostructured surface with enhanced hydrophobicity. The results support 3DPrANIL as novel method to obtain micro- and nanostructured surfaces with different functionalities like iridescence and hydrophobicity., This study was funded by AEI /10.13039 /501100011033/ Unión EuropeaNextGenerationEU/PRTR (grants PID2019-107514GB-I00/AEI/10.13039/501100011033, PID2019-106125GB-I00/ AEI/10.13039/501100011033,and TED2021-129845B-I00). Dr. G. Doerk is gratefully acknowledged(Center for Functional Nanomaterials, Brookhaven National Laboratory,USA) for the support in the preparation of silicon molds. The synchrotronexperiments were performed at NCD-SWEET beamline at ALBASynchrotron with the collaboration of M. Malfois and I.Šics., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dewetting Effects in Poly(vinylidene fluoride-trifluoroethylene) Thin Films on Poly(3-hexylthiophene) Substrates

  • Cui, Jing
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
  • Nogales, Aurora
7 pags., 5 figs., 1 tab., Bilayers of ferroelectric polymers [poly(vinylidene fluoride-trifluoroethylene), PVDF-TrFE] on semiconducting poly(3-hexylthiophene) (P3HT) substrates have been prepared by sequential spin coating. When creating thin layers of PVDF-TrFE from its solution in methyl ether ketone (MEK), they exhibit dewetting in the form of holes for thicker P3HT substrates, whereas they form continuous layers on thinner P3HT substrates. The dispersive and polar components of the surface tension of the different P3HT substrates were obtained through contact angle measurements. An estimation of the shape of the disjoining pressure as a function of thickness of a liquid film of MEK on top of the different P3HT substrates was obtained. Through these estimations, we observe that the stability region for continuous film formation shifts toward higher thicknesses for the samples where experimentally the holes are observed. This work provides understanding on the mechanism of stable film formation and effective tools to control the formation of holes, in functional polymer bilayers, of special importance in the fabrication of organic thin film-based devices., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MICINN) through projects PID2019-107514GB-I00/AEI/10.13039/501100011033 and PID2019-106125GB-I00/AEI/10.13039/501100011033, the Key Scientific Research Project of Henan province (18A430004), and the group innovation space project of ZZULI (2017ZCKJ214). Previous experiments performed by J.C. during her PhD inspired this work. The description of these experiments in J.C thesis is similar to the description of the experiments on this manuscript. J.C. also acknowledges the China Scholarship Council for funding her research during her stay at IME-CSIC (File No. 201207040083)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of film thickness on laser induced surface structures formation on optically transparent polymer films

  • Cui, Jing
  • Nogales, Aurora
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
9 pags., 9 figs., Laser-induced periodic surface structures can be prepared on polymer thin films, despite the absence of light absorption at the wavelength of the irradiating laser, by using a bilayer approach. Nanostructuring of a poly(3-hexylthiophene-2,5-diyl) (P3HT) layer, by laser irradiation at 532 nm, covered by a thin layer of a non-absorbing polymer, in this case, the ferroelectric copolymer poly(vinylidene fluoride - trifluoro ethylene),P(VDF-TrFE), allows the development of a grating-like structure on the surface. The range of thicknesses of the upper layer, which leads to the formation of LIPSS, has been determined. It is verified that for a thickness larger than 40 nm, no periodic structures are formed, neither in the upper layer nor in the bottom P3HT one. This can be explained considering a mechanical restriction which prevents P3HT rearrangement. The upper nanostructured surface layer exhibits ferroelectric properties as proven by piezoresponse force microscopy measurements., This research was funded by the Spanish State Research Agency (AEI) through projects PID2019-107514 GB-I00/AEI/10.13039/501100011033 and PID2019-106125 GB-I00/AEI/10.13039/501100011033. The assistance of D. Hermida from ESRF is gratefully acknowledged. J.C also acknowledges the China Scholarship Council for funding her research during her stay at IEM-CSIC (File No 201207040083)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the crystal structure and hydrogen bonding during cold crystallization of Poly(trimethylene 2,5-furanoate)

  • Toledano, Óscar
  • Galvez, Óscar
  • Sanz, Mikel
  • García-Arcos, Carlos
  • Rebollar, Esther
  • Nogales, Aurora
  • García-Gutiérrez, Mari Cruz
  • Santoro, Gonzalo
  • Irska, I.
  • Paszkiewicz, S.
  • Szymczyk, A.
  • Ezquerra, Tiberio A.
12 pags., 11 figs., 2 tabs., Here, we present a detailed description of the in situ isothermal crystallization of poly(trimethylene 2,5-furandicarboxylate)(PTF) as revealed by real-time Fourier transform infrared spectroscopy (FTIR) and grazing incidence wide-angle X-ray scattering (GIWAXS). From FTIR experiments, the evolution of hydrogen bonding with crystallization time can be monitored in real time, while from GIWAXS, crystal formation can be followed. Density functional theory (DFT) calculations have been used to simulate FTIR spectra for different theoretical structures, enabling a precise band assignment. In addition, based on DFT ab initio calculations, the influence of hydrogen bonding on the evolution with crystallization time can be understood. Moreover, from DFT calculations and comparison with both FTIR and GIWAXS experiments, a crystalline structure of poly(trimethylene 2,5-furandicarboxylate) is proposed. Our results demonstrate that hydrogen bonding is present in both the crystalline and the amorphous phases and its rearrangement can be considered as a significant driving force for crystallization of poly(alkylene 2,5-furanoate)s., This work was supported by grants PID2019-107514GB-I00/AEI/10.13039/501100011033, PID2019-106125GB-I00/AEI/10.13039/501100011033, and TED2021-131914B−I00 andTED2021-129845B−I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”. G.S.acknowledges grant RYC2020-029810-I funded by MCIN/AEI/10.13039/501100011033 and by “ESF Investing in yourfuture”. O.T. acknowledges support from the Spanish Ministry of Universities with European Union funds Next GenerationEU through a Margarita Salas fellowship. S.P. would like to thank them for financial support from the National Science Centre within project SONATA no. 2018/31/D/ST8/00792.The authors acknowledge J.P. Sánchez for technical supportand E. Solano and M. Malfois for support in the experimentsperformed in NCD-SWEET beamline at ALBA synchrotron(Cerdanyola del Vallès, Barcelona, Spain) with the collabo-ration of ALBA staff.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser-Induced Periodic Surface Structures in Polymers with Tailored Laser Fields

  • de Nalda, R.
  • Corrales, Maria Eugenia
  • Recio, Pedro
  • Casasús, Ignacio M.
  • Bañares, Luis
  • Ezquerra, Tiberio A.
  • Rebollar, Esther
7 pags., 4 figs., In this work, laser-induced periodic surface structures (LIPSS) are generated on the surface of thin films of poly(trimethylene terephthalate) (PTT) fabricated by spin coating on silicon. Previous studies have shown the appearance of LIPSS in this type of materials with femtosecond laser pulses in the near-infrared region of the spectrum, despite the extremely low absorption of the polymer. The present work consists of an exploration of the effect of adding complexity to the femtosecond laser fields employed for irradiation. Changes in the repetition rate of the pulse train, the pulse duration, and the pulse temporal chirp are explored, and conditions for optimum LIPSS formation are identified. The effects of these modifications on the polymer surface topography, assessed by atomic force microscopy, are described and discussed., This work has been funded by the Spanish State Research Agency (AEI)through projects PID2019-106125GB-I00/AEI/10.13039/501100011033,PID2019-107514GB-I00/AEI/10.13039/501100011033, and PID2021-122839NB-I00. P.R. is grateful to Universidad Complutense de Madrid(UCM) for a Margarita Salas postdoctoral contract. I.M.C. is grateful tothe Spanish Ministry of Universities for an FPU predoctoral contract(FPU21/04608). We thank Sandra Paszkiewicz and Anna Szymczyk forthe preparation of the PTT. The facilities of the Center for UltrafastLasers (CLUR) of the Universidad Complutense de Madrid are rate fully acknowledged., Peer reviewed