Pasar al contenido principal

CATALIZADORES PARA LA HIDROGENACION DE BIOCOMPUESTOS CON ACIDO FORMICO Y PARA LA VALORIZACION DE DIOXIDO DE CARBONO

PID2020-119160RB-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effect of the Carbon Support and Conditions on the Carbothermal Synthesis of Cu-Molybdenum Carbide and Its Application on CO2 Hydrogenation to Methanol

  • Dongil, Ana Belén
  • Blanco, Elodie
  • Villora-Picó, Juan José
  • Sepúlveda-Escribano, Antonio
  • Rodríguez-Ramos, Inmaculada
  • Sepúlveda-Escribano, Antonio|||/items/5559b16f-e8a5-408d-8b38-429fa29048b0
The synthesis of methanol by carbon dioxide hydrogenation has been studied using copper-molybdenum carbides supported on high surface area graphite, reduced graphene oxide and carbon nanotubes. The synthesis conditions and the effect of the support were studied. The catalysts were prepared in situ using H2 or He at 600 °C or 700 °C. Both molybdenum carbide and oxycarbide were obtained. A support with less reactive carbon resulted in lower proportion of carbide obtained. The best results were achieved over a 5 wt.% Cu and 10 wt.% Mo on high surface area graphite that reached 96.3% selectivity to methanol.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Catalizadores bimetálicos basados en Ru y Ni para la reacción de reducción de CO2 a CH4

  • Bustinza, Ainhoa
  • Salcedo, Eloy
  • Liu, Yuefeng
  • García-Bordejé, José Enrique
2 figuras.-- Póster presentado en la Reunión Bienal de la Sociedad Española de Catálisis, SECAT 2021,"Nuevos Retos de la Catálisis en Química, Medio ambiente y Energía", celebrada en Valencia, del 18 al 20 Octubre 2021., Debido al calentamiento global, el “Green Deal” de la Comisión Europea ha propuesto la reducción de las emisiones de CO2 al menos un 40% respecto los niveles de 1990 y aumentar la cuota de energía renovable al menos un 32%. El principal problema de la energía renovable es que es intermitente y no está alineada con la demanda. Por tanto, hay una necesidad urgente de encontrar medios de almacenar dicha energía. La tecnología de electrolisis del H2O para transformar la electricidad renovable en H2 es una tecnología madura. Sin embargo, el H2 es difícil de almacenar y transportar. El H2 puede convertirse en CH4 haciéndolo reaccionar con CO2 capturado mediante la reacción de Sabatier. De esta manera, se contribuye a cumplir dos objetivos del “Green Deal” europeo: el aumento de la cuota de energías renovables y la reducción de emisiones de CO2. Puesto que es una reacción altamente exotérmica, la concentración de equilibrio de CH4 aumenta la disminuir la temperatura, por lo que es necesario encontrar catalizadores activos a bajas temperaturas. En este trabajo se han preparado dos tipos de catalizadores bimetalicos. Por un lado, se han preparado por impregnación sucesiva catalizadores bimetálicos soportados en alúmina conteniendo: (i) Ni-Ru y (ii) un metal de metanación (Ni o Ru) y metal alcalino (Na, K). Estos catalizadores bimetálicos se han probado en la reacción de metanación de CO2 con H2. El objetivo es mejorar el comportamiento catalítico respecto a los catalizadores monometálicos. En el caso de los catalizadores bimetálicos Ni-Ru la aproximación es mejorar el catalizador reduciendo la cantidad de Ru al mínimo, mientras que en los bimetálicos con metal alcalino la estrategia consiste en aumentar la basicidad del catalizador, y por tanto, favorecer la adsorción de CO2. Se ha estudiado como influyen distintos parámetros de la síntesis por impregnación sucesiva en el comportamiento catalítico y su relación con la estructura y basicidad de los catalizadores caracterizada mediante diversas técnicas instrumentales (XPS, TEM, TPD y TPSR)., Se agradece la ayuda al Ministerio de Ciencia e Innovación por los proyectos ENE2016-79282-C5-1-R (AEI/UE/FEDER) y PID2020-119160RB-C21
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hybrids of reduced graphene oxide aerogel and CNT for electrochemical O2 reduction

  • Hernández-Ferrer, Javier
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
9 figures, 1 table.-- Supplementary material available., Carbon nanotubes (CNTs), graphene aerogels (GAs), and their hybrid (CNT-GA) prepared by hydrothermal treatment were tested in the electrocatalytic oxygen reduction reaction (ORR). The importance of porous structure derived from the combination of mesoporosity coming from CNTs with macroporosity stemming from GAs was evidenced because the hybrid carbon material exhibited synergistic performance in terms of kinetic current and onset potential. Different electrocatalysts were prepared based on these hybrids doped with nitrogen using different precursors and also supporting Fe nanoparticles. N-doped carbon hybrids showed higher electrocatalytic activity than their undoped counterparts. Nevertheless, both doped and undoped materials provided a mixed two and four electron reduction. On the other hand, the addition of a Fe precursor and phenanthroline to the CNT-GA allowed preparing an N-doped hybrid containing Fe nanoparticles which favored the 4-electron oxygen reduction to water, thus being an excellent candidate as a structured cathode in fuel cells., This research was funded by Spanish Ministry MICINN/AI under Projects PID2019-104272RB-C51/AEI/10.13039/501100011033, PID2020-119160RB-C21 and Gobierno de Aragon (Grupo reconocido DGA T03_20R,) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Promotion of Ru or Ni on alumina catalysts with a basic metal for CO2 hydrogenation: Effect of the type of metal (Na, K, Ba)

  • García-Bordejé, José Enrique
  • Dongil, Ana Belén
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
10 figures, 1 table.-- Supplementary information available.-- This article belongs to the Special Issue State-of-the-Art Nanomaterials for Energy Storage/Conversion and Catalysis in Spain., Ru and Ni on alumina catalysts have been promoted with a 10 wt% of alkali metal (K or Na) or alkaline earth metal (Ba) and tested in CO2 methanation. For the catalyst consisting of Ni and Ba, the variation of Ba loading while keeping Ni loading constant was studied. The promotion in terms of enhanced CH4 yield was found only for the addition of barium to 15 wt% Ni/Al2O3. In contrast, K and Na addition increased the selectivity to CO while decreasing conversion. For the Ru-based catalyst series, no enhancement in conversion or CH4 yield was attained by any of the alkaline metals. CO2 temperature-programed desorption (CO2-TPD) revealed that the amount of chemisorbed CO2 increased significantly after the addition of the base metal. The reactivity of COx ad-species for each catalyst was assessed by temperature-programed surface reaction (TPSR). The characterization revealed that the performance in the Sabatier reaction was a result of the interplay between the amount of chemisorbed CO2 and the reactivity of the COx ad-species, which was maximized for the (10%Ba)15%Ni/Al2O3 catalyst., The Financial support from the Spanish Ministry MINECO (projects PID2020- 119160RB-C21 and -C22), Gobierno de Aragón (Grupo Reconocido DGA T03_20R), and associated EU Regional Development Funds are gratefully acknowledged, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cyclic performance in CO2 capture-methanation of bifunctional Ru with different base metals: Effect of the reactivity of COx ad-species

  • García-Bordejé, José Enrique
  • Dongil, Ana Belén
  • Moral Pombo, Jorge
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
9 figures.-- Supplementary information available., Bifunctional materials based on Ru nanoparticles and an alkaline metal (K, Na or Ba) have been scrutinized for several cycles of CO2 capture and subsequent methanation at different temperatures from 250 ºC to 450 ºC. The optimum performance in terms of stable cyclic operation, amount of captured CO2 and relevant methane productivity was attained at different temperature window for each material. For the materials here prepared, the limiting lower operation temperature of stable cyclic performance was determined by the methanation kinetics, which depended on reactivity of COx ad-species captured with each alkaline metal. The highest activity was found with Ba-containing materials, which exhibited a stable and relevant cyclic CH4 productivity at 250 ºC, being one of the lowest operation temperatures reported for a dual functional material to date. This material exhibited stable cyclic performance also in the presence of O2 and H2O, although the CH4 productivity decreases slightly and reversibly compared to that using CO2 containing gas free of O2 and H2O., The Financial support from Spanish Ministry MINECO (projects PID2020-119160RB-C21 and -C22), Gobierno de Aragón (Grupo Reconocido Gobierno de Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of temperature and presence of minor amount of metal on porous carbon materials derived from ZIF8 pyrolysis for electrocatalysis

  • Hernández-Ferrer, Javier
  • Gracia Martín, Mario
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
11 figures, 4 tables.-- Supplementary information available., ZIF8 without and with adsorption of minor amounts of Co precursor have been pyrolized at different temperatures studying systematically the effect of carbonization temperature on the texture, composition and ORR performance both in acidic and basic media. The increase of pyrolysis temperature diminished the N content but increased the graphitic character. The trade-off between these two parameters in metal-free electrocatalysts resulted in an improvement of ORR performance, which is met for the highest pyrolysis temperature of 1000 ºC. Moreover, the adsorption of minor amount of Co precursor enhanced further the ORR performance, increased the graphitic character and the porosity of the resulting carbon material. Morphologically, these carbon materials kept the polyhedral shape of ZIF8 and were covered by graphitic nanostructures devoid of metal nanoparticles. Co metal catalysed the growth of these graphitic nanostructures and concomitantly is stabilized as monoatomic Co-Nx-C species preventing the agglomeration as metal nanoparticles. Therefore, the need of an acid washing step is avoided, which is usually necessary in the carbonization of other metal containing MOFs., Grants PID2020-119160RB-C21 and PID2019-104272RB-C51 funded by MCIN/AEI/10.13039/501100011033 and Aragón Government (Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamics of Pd subsurface hydride formation and their impact on the selectivity control for selective butadiene hydrogenation reaction

  • Asedegbega-Nieto, Esther
  • Iglesias Juez, Ana
  • di Michiel, Marco
  • Fernández, M.
  • Rodríguez-Ramos, Inmaculada
  • Guerrero-Ruiz, Antonio
Structure-sensitive catalyzed reactions can be influenced by a number of parameters. So far, it has been established that the formation of Pd-C species is responsible for the behavior of Pd nanoparticles employed as catalysts in a butadiene partial hydrogenation reaction. In this study, we introduce some experimental evidence indicating that subsurface Pd hydride species are governing the reactivity of this reaction. In particular, we detect that the extent of formation/decomposition of PdHx species is very sensitive to the Pd nanoparticle aggregate dimensions, and this finally controls the selectivity in this process. The main and direct methodology applied to determine this reaction mechanism step is time-resolved high-energy X-ray diffraction (HEXRD)., The authors acknowledge financial support from Spanish Ministry MINECO (projects PID2020-119160RB-C21 and -C22)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dual functional materials based on Ni and different alkaline metals on alumina for the cyclic stepwise CO2 capture and methanation

  • García-Bordejé, José Enrique
  • Dongil, Ana Belén
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
8 figures.-- Supplementary information available., Bimetallic catalysts consisting of nickel and one alkali or alkaline-earth metal (Na, K or Ba) on alumina support have been tested in the cyclic CO2 capture and subsequent methanation. The best performance was attained with a different material for cyclic tests (K-Ni/Al) than for Sabatier reaction (Ba-Ni/Al). In cyclic tests, the methane productivity shows different dependence with the temperature for each alkali and alkaline-earth metal. For temperature of 300 °C or above, the dual functional materials show stable cyclic performance when the capture is performed both from 5% CO2 in Ar and from simulated flue gas containing also O2 and H2O. Using the later feed, the CH4 productivity diminish reversibly compared to oxygen free conditions and nickel metal oxidises significantly. K-Ni/Al exhibited the best cyclic performance in terms of CH4 productivity and stability, which is associated to the highest reducibility of oxidised nickel species and the lowest formation of unreducible carbonates., The authors are very grateful to the Grants PID2020-119160RB-C21 and -C22 funded by MCIN/AEI/10.13039/501100011033 and Aragón Government (Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Appendix A. Supplementary data for Dual functional materials based on Ni and different alkaline metals on alumina for the cyclic stepwise CO2 capture and methanation [Dataset]

  • García-Bordejé, José Enrique
  • Dongil, Ana Belén
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
XPS alkaline: The Na 1s XPS peak (Figure S13) can be fitted to two main contributions one at 1071.6 eV which can be ascribed to sodium carbonates and bicarbonates and other at 1073.1 eV which can be ascribed to sodium oxides and hydroxides. The ratio of carbonate species to alumina (Table 1) do not vary significantly or decreases slightly after reaction in agreement with C 1s fitting. Therefore, there is no building up of stable carbonates at 450 ºC, which are comparable to those formed from atmospheric CO2 adsorption at room temperature.-- We have fitted the Ba 3d5/2 peak to two peaks separated by around 2 eV (Figure S14). One peak at 779.0 eV which can be ascribed to barium oxide (BaO).The other peak at 781.0 eV that can be ascribed to Ba atoms in a decomposed barium carbonate layer. [5–8] In contrast to other materials, the Ba-containing materials contains less total carbon, nickel carbide and carbonates after CO2 reaction than before reaction (Table 1). In fact, the spectra of passivated material and reacted material are quite similar (Figure S15). This suggests that no stable carbonates or carbide species different from CO2 adsorbed at room temperature are formed. Some authors also found the carbonate localized in the outermost 20 A of passivated Ba titanate. The authors related this carbonate formation to possible contamination by atmosphere.-- Under a Creative Commons license BY-NC 4.0., Figure S1. Cyclic CO2 capture and hydrogenation at 250 ºC for the different catalysts: (a) Na-Ni/Al; (b) K-Ni/Al; (c) Ba-Ni/Al. Figure S2. Cyclic CO2 capture and hydrogenation at 350 ºC for the different catalysts: (a) Na-Ni/Al; (b) K-Ni/Al; (c) Ba-Ni/Al. Figure S3. Cyclic CO2 capture and hydrogenation at 400 ºC for the different catalysts: (a) Na-Ni/Al; (b) K-Ni/Al; (c) Ba-Ni/Al. Figure S4. Cyclic CO2 capture and hydrogenation at 450 ºC for the different catalysts: (a) Na-Ni/Al; (b) K-Ni/Al; (c) Ba-Ni/Al. Figure S5. produced CH4 (a) and CO (b) and released CO2 (c) within 100 s upon H2 admission at 250 ºC. Figure S6. Produced CH4 (a) and CO (b) and released CO2 (c) within 100 s upon H2 admission at 300 ºC. Figure S7. Produced CH4 (a) and CO (b) and released CO2 (c) within 100 s upon H2 admission at 350 ºC. Figure S8. Produced CH4 (a) and CO (b) and released CO2 (c) within 100 s upon H2 admission at 400 ºC. Figure S9. Produced CH4 (a) and CO (b) and released CO2 (c) within 100 s upon H2 admission at 450 ºC. Figure S10. HAADF-STEM images (a,c,e) and particle size distribution (b,d,f) of DFMs: (a,b) K-Ni/al; (c,d) Na-Ni/Al; (e,f) Ba-Ni/Al. Figure S11. Cyclic CO2 capture and hydrogenation at 350 ºC for the different catalysts using feed B (5% CO2, 11% H2O, 4.5% O2 in Ar): (a) K-Ni/Al; (b) Na-Ni/Al; (c) Ba-Ni/Al. Figure S12. Comparison of productivity switching the composition of the capture gas between feed A (5% CO2 in Ar), feed B (5% CO2, 11% H2O, 4.5% O2 in Ar) and feed A again. (a) cyclic CH4 productivity with feed B;Figure S13. Temperature programmed reaction of 15%Ni on alumina. Fitting of Ni 2p3/2: Table S1. Result of the Fitting of Ni 2p3/2 peaks for Ba-Ni. Table S2. Result of the Fitting of Ni 2p3/2 peaks for K-Ni. Table S3. Result of the Fitting of Ni 2p3/2 peaks for Na-Ni. Fitting of C 1s: Table S4. Result of the Fitting of C1s peaks for Ba-Ni. Table S5. Result of the Fitting of C1s and K2p peaks for K-Ni. Table S4. Result of the Fitting of C1s peaks for Na-Ni. XPS alkaline: Figure S14. Fitting of XPS Na 1s peak for Na-Ni/Al after passivation, after CO2 capture at 350 ºC and this latter material reduced in-situ at 250 ºC and 350 ºC. Figure S15. Fitting of XPS Ba 3d5/2 peak for Ba-Ni/Al after passivation, after CO2 capture at 350 ºC and this latter material reduced in-situ at 250 ºC and 350 ºC., The authors are very grateful to the Grants PID2020-119160RB-C21 and -C22 funded by MCIN/AEI/10.13039/501100011033 and Aragón Government (Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Advances in process intensification of direct air CO2 capture with chemical conversion

  • García-Bordejé, José Enrique
  • Gonzalez-Olmos, R.
14 figures, 6 tables., Capturing CO2 from air (DAC) is becoming an attractive technological route to face the climate crisis. This paper reviews the existing research efforts to integrate DAC with conversion technologies to transform the captured CO2 into chemicals or fuels. The approach can potentially lead to net zero carbon emissions, thus being of interest in a circular economy framework. A growing amount of research has been devoted to the combination of DAC with CO2 conversion, leading to creative strategies which start to be scaled up. In this review, we have critically analysed the existing approaches by the degree of process integration. From the point of view of process intensification, the integration of both capture and reaction in the same vessel can potentially lead to equipment and energy cost savings besides other synergistic effects. In this vessel, the DAC and conversion can occur either in consecutive stages with change of feed or spontaneously in a cascade reaction without changing the conditions. As a side effect, the benefits entailed by process intensification in different levels of integration may be a decisive driving force for the widespread deployment of DAC. This paper discusses the ongoing research and perspectives to guide researchers in this promising new field., The authors acknowledge sincerely the funding of MCIN/AEI/10.13039/501100011033 (Grant PID2020-119160RB-C21) and Aragón Government (Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged. We also acknowledge the support by projects Opti-CCU (2022-DI-00053) and RFC+PU (2021 BP 00029) funded by the Catalan Government. GESPA group from IQS has been recognized as Consolidated Research Group by the Catalan Government (2021 SGR 00321)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cobalto atómicamente disperso en carbón poroso dopado con nitrógeno a partir de la cabonización de ZIF-8 para la ORR

  • Hernández-Ferrer, Javier
  • Gracia Martín, Mario
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
1 figura.- Abstract del póster de Tecnologías para la generación sostenible de energía presentada en la XVI Reunión del Grupo Español del Carbón (Reunión GEC 2023), celebrada en Gijón del 22 al 25 de octubre de 2023., La reducción electroquímica de oxigeno es una reacción de gran importancia para la transición energética ya que está en la base de las pilas de combustible y las baterías de aire. El reto que existe actualmente es aumentar la actividad másica a la vez que evitar o reducir el uso de metales nobles. Especies del tipo metal transición-N-C, que imitan ftalocianinas se han demostrado como una buena alternativa para obtener una alta actividad másica [1] [10]. Estas especias se podrían preparar por la carbonización controlada de MOFs ya que estos contienen tanto metales como nitrógenos atómicamente dispersos. Algunos trabajos pioneros carbonizaron ZIF-67 ) [16] or ZIF-8 [17] con metales. En estos trabajos se realizó un lavado ácido para eliminar las nanopartículas formadas, pero aun así quedaban nanopartículas encapsuladas reduciendo la actividad másica en la ORR. En este trabajo hemos carbonizado ZIF8 con y sin impregnación de 0.9 wt% Co y lo hemos carbonizado a tres temperaturas diferentes, 700 ºC, 900 ºC y 1000 ºC. Los carbones dopados con nitrógeno se han caracterizado exhaustivamente y se han probado en la ORR tanto en medio neutro como básico. De esa manera ha sido posible poner algo de luz el efecto de la temperatura de carbonización y en el efecto de la presencia de Co en las propiedades de los materiales carbonosos y en su comportamiento electrocatalítico en la ORR., Proyectos PID2020-119160RB-C21 y PID2019-104272RB-C51 financiados por gobierno de Aragón (Aragón T03_20R) y MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Innovative approaches to sustainable ammonia synthesis under mild conditions

  • Castillejos-López, Eva
  • García-Bordejé, José Enrique
6 figures, 2 tables., Ammonia is one of the most important chemicals in the world because it is a feedstock for fertilizer production and, moreover, it has been proposed as a convenient storage media for renewable H2. Currently, it is produced by Haber-Bosch process, which entails harsh operation conditions and a high carbon footprint, rendering the process difficult to be run by renewable energy. Therefore, substituting the conventional Haber-Bosch process by other approach less energy-intensive and carbon-free is an urgent need. A milder process for ammonia synthesis will enable the implementation of smaller distributed plants more aligned with renewable energies. For this reason, there is a plethora of current research focusing on the development of suitable catalysts with higher activity and selectivity for nitrogen reduction and processes that will work under less severe operating conditions or even at ambient conditions. Some of the most relevant research approaches are here revised and compared., The Financial support from Spanish Investigation Agency (projects PID2020-119160RB−C21 and -C22), Gobierno de Aragón (Grupo Reconocido Gobierno de Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hidrogenación de CO2 mediante catalizadores basados en Ru sobre distintos soportes: efecto de la basicidad

  • Gracia Martín, Mario
  • García-Bordejé, José Enrique
1 figura.-- Póster presentado en la XVI REUNIÓN GEC 2023 en la sección Aplicaciones catalíticas, medioambientales y biosanitarias, Gijón (España), celebrada del 22 al 25 de octubre de 2023., Debido a que la energía de fuentes renovables se obtiene de manera fluctuante y descentralizada se hace necesario su almacenamiento y transporte. Por otro lado, una economía circular requiere la utilización de CO2 como materia prima. La conversión de energía renovable en H2 por electrolisis de agua y su posterior reacción con CO2 para producir CH4 permite abordar estos dos desafíos al mismo tiempo. Además, el CH4 sintético se puede almacenar y transportar usando las actuales infraestructuras, lo que no es posible con el H2 producido directamente por electrolisis del agua. La reacción entre CO2 con H2 se descubrió hace un siglo y se conoce con el nombre de la reacción de Sabatier [1]. Como catalizadores se han empleado principalmente Ni o Ru soportados en óxidos metálicos. En este trabajo se ha abordado la mejora de los catalizadores mediante usando diferentes soportes con distintas basicidades y mediante la preparación de catalizadores bimetálicos. Los catalizadores bimetálicos con la doble función de captura y conversión también se han ensayado en ciclos para la captura del CO2 de gases de combustión., Proyectos PID2020-119160RB-C21 financiados por MCIN/AEI/10.13039/501100011033 y gobierno de Aragón (Aragón T03_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reactivity of n-butene using carbon supported Mo carbide and Ni, Mo, Co phosphides catalysts

  • Fernández-Morales, J.M.
  • Martínez Quintana, Laura
  • Dongil, Ana Belén
  • Asedegbega, E.
  • Castillejos, E.
  • Rodríguez-Ramos, Inmaculada
  • Guerrero-Ruiz, Antonio
Conversion of 1-butene was studied over Mo carbides and Ni, Co and Mo phosphides, under continuous gas phase operating conditions at atmospheric pressure and 100 °C, using 1-butene/helium mixture in a molar ratio of 4:1. The conversion was in the range 30–44% and the values were quite stable except for (1:2)CoP, (1:2)NiP, (1:2)MoP-and MoxC supported catalysts. The main reaction was isomerization of 1-butene, and the selectivity to dimerization was observed in a higher ratio on (1:2)MoP and MoxC supported on high surface area graphite. In situ XRD, XPS, NH3-TPD and thermogravimetry (TG) have been used to assess for the formed species on the surface. © 2023 The Authors, Financial support from the Spanish Ministry MINECO (projects PID2020-119160RB-C21 and -C22) and RYC2020-030626-I and from Spanish National Research Council 20228AT002 is gratefully acknowledged., Supplementary material, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Formic Acid Dehydration Using Mechanochemically Prepared TiO2-Graphite Composites

  • Yruela-Garrido, Marta
  • Martín-Rodríguez, Nuria
  • Castillejos-López, Eva
  • Campos Castellanos, Eduardo
  • Conesa, José María
  • Rodríguez-Ramos, Inmaculada
  • Guerrero-Ruiz, Antonio
Commercial high surface area graphite (HSAG300) and commercial TiO2 were used to produce composite materials through a simple mechanochemical method involving milling and ultrasonic treatments. The acid and basic sites exposed on the surfaces of these materials were characterized by temperature-programmed desorption (TPD) of ammonia and carbon dioxide. The catalytic materials were tested in the dehydration reaction of formic acid to produce hydrogen-free CO. While HSAG300 is practically inactive under reaction conditions (continuous gas flow at temperatures in the range of 100-250 ºC), all samples containing TiO2 are active, exhibiting high selectivity to CO without significant deactivation at moderate reaction temperatures. It is demonstrated that the presence of graphite in the catalysts enhances the specific catalytic activity of TiO2. Assuming that the dehydration reaction is catalyzed by acid sites on the TiO2 surfaces, a comparative evaluation of the surface sites reveals that the graphite-TiO2 interactions not only change the density of surface sites but also modify the strength of the acid centers of TiO2. In summary, the interaction of HSAG300 with TiO2 modulates the surface properties of the prepared composite catalysts, decreasing the total number of basic surface sites and increasing the strength of acidic sites compared to bare TiO2., Authors recognize financial support from Spanish Project grants PID2020-119160RB C21 and -C22 funded by MCIN/AEI, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Effect of post activation treatment and presence of minor amount of metal on nitrogen-doped carbon materials derived from laser-assisted pyrolysis for oxygen reduction reaction

  • Pakrieva, Ekaterina
  • Hernández-Ferrer, Javier
  • Martínez, Gema
  • Balas, Francisco
  • Hueso, José L.
  • García-Bordejé, José Enrique
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Santamaría, Jesús
Trabajo presentado a las XXXVII Jornadas Nacionales de Ingeniería Química: El puente hacía un futuro sostenible, celebradas en Castellón del 13 al 15 de septiembre de 2023.-- Temática: Energía y Sostenibilidad., The authors thank the Spanish Ministry of Science and Innovation (LAERTES project) and the European Commission (ERC-Advanced Grant CADENCE) for funding. The synthesis of materials has been performed by the Platform of Production of Biomaterials and Nanoparticles of the NANBIOSIS ICTS, more specifically by the Nanoparticle Synthesis Unit of the CIBER in BioEngineering, Biomaterials & Nanomedicine (CIBERBBN). The characterization has been carried out in the ELECMI-ICTS facilities. Financial support from Diputación General de Aragón under project T03_23R (Grupo Reconocido), Projects PID 2020-119160RB-C21 and PID2019-104272RB-C51 funded by MCIN/AEI/10.13039/501100011033 are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Isothermal stepwise CO2 capture-methanation using a dual functional material: effect of the temperature and type of alkaline metal

  • García-Bordejé, José Enrique
  • Dongil, Ana Belén
  • Rodríguez-Ramos, Inmaculada
1 figure.-- Work presented at the EuropaCAT 2023, 15th European Congress of Catalysis, 27 august-1 september 2023, Prague (Czech Republic)., After the pioneering works of Farrauto et al. [1], dual functional materials (DFM) have emerged recently for been studied in the last years for the stepwise isothermal CO2 capture and methanation. Different combinations of transition metals (Ni, or Ru) and alkali or alkaline earth metals have been explored [2]. For a real application, it is important to assess its cyclic stability at different temperatures under realistic conditions, such as real flue gas, which also contains O2 and H2O and other impurities. In addition, it should be born in mind that operating at the lowest temperature as possible is also highly searched for. This would reduce the energy required for heating when the flue CO2-containing gas is emitted at low temperature or for direct capture from the air (DAC). Herein, we have performed a parametric study of the effect of the reaction temperature on the cyclic performance of DFMs consisting of a metal active in methanation (Ni or Ru) and different alkaline metals (Na, K, Ba) with CO2 capture ability [3]., Grants PID2020-119160RB-C21 and C22 funded by MICIN/AEI/10.13039/501100011033 and Aragón Government (Aragón T03_20R) amd associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Materiales de doble función soportados en alumina para la captura de CO2 de gases de chimenea o de la atmosfera y su conversión a metano

  • García-Bordejé, José Enrique
  • Moral Pombo, Jorge
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
4 figures.-- Work presented at the CICAT 2024, 29º Congreso Iberoamericano de Catálisis, 23th-27th september 2024, Bilbao (Spain)., [EN] Dual functional materials (DFM) consist of two chemical species supported on alumina: one to capture CO2 (Na, K or Ba) and other to catalyse methanation (Ru or Ni). These materials have been tested in cycles of CO2 capture and methanation, whereby the CO2 capture was performed from a simulated flue gas and also from air (DAC). Using simulated flue gas, both processes of capture and methanation were performed isothermally at different temperatures (250-450 ºC) changing the feed between the flue gas and H2. The cyclic stability and the CH4 productivity depended on the temperature and alkaline metal. The highest CH4 productivity was attained at 250 ºC and 300 ºC when using Ba and at 350-450 ºC when using K and Na. The presence of H2O and O2 in the flue gas produced a reversible inhibition of CO2 capture for Ru-based DFMs while for Ni-based DFMs a slight irreversible deactivation also occurs due to the formation of some unreducible Ni species, being minimal for NiK. The DFMs have been tested in cycles of direct air capture (DAC) at ambient temperature. The first results are very promising achieving a high capture capacity of 400 μmol g-1 maintained during 20 cycles., [ES] Los materiales de doble función (DFM) contienen dos especies químicas: una para capturar el CO2 (Na, K o Ba) y otra para catalizar la metanación (Ru o Ni). Los materiales se han probado en ciclos de captura de CO2 tanto simulando un gas de chimenea como para captura directa del aire (DAC). Usando el gas de chimenea, las dos etapas (captura y metanación) se han realizado isotermamente a varias temperaturas (250-450 ºC) cambiando la alimentación entre el gas conteniendo el CO2 y el H2. La estabilidad cíclica y la productividad hacia CH4 son dependientes de la temperatura y del metal básico usado. Las mayores productividades a CH4 se obtuvieron a 250-300 ºC usando Ba y a 350-450 ºC usando K y Na. La presencia de H2O y O2 produce una inhibición reversible de la captura de CO2 para los DFMs con Ru, mientras que para los DFMs con Ni se observa una ligera desactivación irreversible, siendo este efecto menor en el NiK. Asimismo, los DFM se han probado en ciclos de captura directa del aire (DAC) a temperatura ambiente. Los primeros resultados son muy prometedores, consiguiendo una elevada capacidad de captura (400 µmol g-1) que se mantiene durante 20 ciclos., The authors are very grateful to the Grants PID2020-119160RB-C21 and -C22 funded by MCIN/AEI/10.13039/501100011033 and Aragón Government (Aragón T03_20R), and associated EU Regional Development Funds are gratefully acknowledged., Peer reviewed