Pasar al contenido principal

CONTROL AVANZADO DE CONVERTIDORES DE FUENTE DE CORRIENTE (CSI) MONOFASICOS Y TRIFASICOS

PID2021-122821NB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 33
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Control y análisis de la dinámica cero en inversores trifásicos de fuente de corriente mediante un modelo de variables de estado complejas

  • Rahimi, Leila
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Griñó Cubero, Robert|||0000-0001-6045-4600
Este trabajo analiza la dinámica cero de inversores de fuente de corriente trifásicos alimentados desde una fuente de tensión y conectados a una carga resistiva local o a la red eléctrica. El análisis de la dinámica cero concluye que, cuando la fuente de alimentación se modela a partir de su circuito equivalente de Thévenin, se producen problemas de estabilidad que se manifiestan en la corriente del bus cc, si el lazo de control fuerza un buen seguimiento de la tensión de salida. El artículo incluye el diseño de un controlador de bucle anidado alternativo que supera la inestabilidad interna de la corriente del inductor, Este trabajo ha sido financiado en parte por el Gobierno de España a través del programa Agencia Estatal de Investigación en Proyecto PID2021-122821NB-I00 y por la Generalitat de Catalunya a través del Proyecto 2021 SGR 00376. El trabajo de L. Rahimi está financiado por la beca 2022-FPU-UPC-36.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

The Ohm’s Law for (non-symmetric) three-phase three-wire electrical circuits: from a complex-valued to a geometric algebra approach

  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Velasco García, Manel|||0000-0002-0764-3063
  • Zaplana Agut, Isiah|||0000-0002-0862-3240
  • Martí Colom, Pau|||0000-0002-5189-0782
This paper introduces the modelling of three-phase electrical systems using the Geometric Algebra approach and is compared with the complex-valued framework in the case of non-symmetrical conditions. The main benefit of the geometric algebra framework is the possibility of representing the dynamics of unbalanced scenarios by a single-input, single-output relationship. The paper presents step-by-step, building the geometric impedance and revisiting Ohm’s law, and compares the complex-valued modelling widely used in balanced three-phase circuits., This work was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021- 122821NB-I00 and by the Generalitat de Catalunya, Spain through the Projects 2021-SGR-00098, 2021-SGR-00375 and 2021-SGR00376., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Voltage regulation in an interleaved circular chain sliding mode controlled multiphase converter

  • Biel Solé, Domingo|||0000-0002-0364-7681
  • Arroyo de Fàbregas, Adrià
  • Repecho del Corral, Víctor|||0000-0003-0584-5443
In this article a multiphase synchronous buck converter controlled by a sliding mode control (SMC) in a circular chain control (CCC) configuration is presented. The proposed switching functions with the CCC architecture ensure a robust output voltage regulation when facing changes in the load or the input voltage, while providing current equalization among the phases. The novelty of the work is the simple control structure based on a first order SMC implemented by means of hysteresis-band comparators, requiring no external signals or additional hardware to lead the system to an interleaving operation, obtaining a harmonic cancellation that allows the size reduction not only of the output capacitor but also of the inductors. It is proved that, in the steady state, the switching function exhibits a periodic solution with a period equal to the switching period. Besides, the steady-state switching frequency expression as a function of the hysteresis bandwidth is derived. The work includes the analytical analysis of the proposed solution, a set of numerical simulations and, finally, an experimental validation. The numerical and experimental results confirm the predicted good performance of the proposed control., This work was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021- 122821NB-I00 and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Dual active bridge simultaneous input admittance passivity shaping and reference tracking using low order H-infinity control

  • Pérez Ruiz, Juan José
  • Santamargarita Mayor, Daniel
  • Molinero Blanco, David
  • Huerta Sánchez, Francisco
  • Pizarro Pérez, Daniel
  • Cóbreces Álvarez, Santiago
  • Griñó Cubero, Robert|||0000-0001-6045-4600
© 2024 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, This paper presents a design methodology for the output voltage control loop of a dual active bridge (DAB). It is based on fixed-order H8 non-smooth synthesis combined with passivity restrictions over closed-loop impedance transfer function, known to have a critical impact on system voltage stability. The proposal inherits the advantages of modern techniques, making use of simple frequential weighting-based design and plant dynamical complexity black-boxing, while keeping controller complexity low., This work has been funded by BRONTE project (SBPLY/21/180501/000147), by the Junta de Comunidades de Castilla La Mancha and the European Union through the European Regional Development Fund; ASTRAPE project (CM/JIN/2021-019), financed by the Comunidad de Madrid in the framework of the Multiannual Agreement with the Universidad de Alcalá in the line of action ”Stimulus to the Research of Young Doctors”, within the V PRICIT framework program; and projects CRESIPSPE (PID2021-1256280B-C22) and OPEMRES (TED2021-130610B-C21) f inanced by Spanish Ministerio de Ciencia e Innovaci´ on, Agencia Estatal de Investigación and FEDER,UE 10.13039/501100011033. The work of Robert Griñ´ o was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021-122821NB-I00 and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Sliding-mode control in the dq-reference frame for a three-phase CSI feeding an isolated load

  • Boira Pujol, Pau|||0009-0004-0674-2889
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Griñó Cubero, Robert|||0000-0001-6045-4600
© 2026 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper proposes a sliding-mode controller for a single-stage, three-phase current source inverter supplying an isolated load. The control architecture, derived from the dq model of the converter, features two cascaded loops: an inner slidingmode control loop that regulates the q-axis voltage component together with the DC current, and an outer proportional-integral control loop for the d-axis. In contrast to traditional linear methods, the proposed sliding-mode control enhances system robustness and transient performance, while the cascaded scheme overcomes the inherent non-minimum phase behaviour of boosttype converters. The effectiveness of the proposed control strategy is verified through numerical simulations, and its practical feasibility is demonstrated experimentally using a Hardware-in-the-Loop (HIL) platform., This work was supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Novel electric arc current emulation system for low-voltage grids

  • Dávila, Asier
  • Otero Olavarrieta, Alberto
  • Planas, Estefanía
  • Cortajarena Echevarría, José Antonio
  • Arias Pujol, Antoni|||0000-0002-5424-5981
An electric arc is a common distribution grid error, even more so with the use of electric vehicles and renewable energy sources that increase the likelihood of grid errors. Several control systems and strategies are under development to minimize electric-arc faults and to guarantee reliable grid performance. All the control strategies must be validated through emulations of the different fault modes at laboratory scale where there is no risk to either the researchers or the facilities. In this study, a novel system is proposed for the emulation of electric arc current waveforms, based on both real measurements and equation-based modeling. The proposed modular system provides the capability to emulate different levels of arcing currents. Validation of the system was demonstrated, in view of the design, the underlying theoretical analysis, and a set of control system simulations and experiments., This work was supported in part by the Government of the Basque Country within the fund for research groups of the Basque University system IT1440-22, by the Agencia Estatal de Investigación within the project PID2021-122821NB-I00, by the Generalitat de Catalunya within the project 2021 SGR 00376, and by the research project PT10709 funded by i-DE Redes Inteligentes S.A.U. through its Global Smart Grids Innovation Hub. Open Access funding provided by the University of Basque Country UPV/EHU., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Four-Leg voltage source converter with independent phase control for ground fault compensation

  • Dávila, Asier
  • Komrska, Tomáš
  • Arias Pujol, Antoni|||0000-0002-5424-5981
  • Cortajarena Echevarría, José Antonio
  • Planas, Estefanía
  • Peroutka, Zdenek
Electrical faults are a frequent occurrence in medium voltage (MV) distribution grids, often affecting or completely interrupting the electrical supply. Among these, single-phase faults are the most common type and passive elements such as Peterson coils have been traditionally employed to mitigate their impact and maintain a reliable power supply. However, these solutions come with inherent drawbacks, including limited flexibility and functionality, which hinder their effectiveness in dynamic grid scenarios. This work presents a novel system designed to ensure high-quality power supply continuity before, during, and after single-phase faults. The proposed approach uses already installed four-leg power converters in the grid, eliminating the need for additional passive equipment. A new control strategy is developed in the natural abc reference frame, which enables the use of classical control techniques in the MIMO system and simplifies the analysis of the output voltage loops without changing the reference frame. Simulations and experimental results confirm that the proposed control framework effectively compensates for faults and maintains grid stability, improving fault resilience in MV distribution networks., This research has been partially supported by the Technology Agency of the Czech Republic, project TN02000025 National Center for Energy II, partially supported the Department of Education of the Basque Government within the fund for research groups of the Basque university system IT1440- 22, partially supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376. The authors wish to express their gratitude to Gipuzkoako Foru Aldundia for the project Etorkizuna Eraikiz 2024–2025. Open Access funding provided by University of Basque Country., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Control PI basado en pasividad para un inversor trifásico de fuente de corriente alimentando una carga local

  • Boira Pujol, Pau|||0009-0004-0674-2889
  • Ortega, Romeo
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Griñó Cubero, Robert|||0000-0001-6045-4600
Este artículo presenta el diseño de un controlador Proporcional-Integral basado en pasividad para un inversor trifásico de fuente de corriente alimentando una carga resistiva. Gracias a la definición de una nueva salida pasiva, se demuestra que el sistema en lazo cerrado es globalmente y asintóiticamente estable. Este resultado resuelve el problema de estabilidad interna señalado en trabajos anteriores para estos convertidores de potencia. Para reforzar el algoritmo de control, el artículo también incluye el diseño de un esquema de estimación de parámetros para las resistencias parásitas y la conductancia de carga. Se han realizado simulaciones numéricas para validar el algoritmo de control. Asimismo, se compara el comportamiento utilizando el modelo promediado del convertidor de potencia y un modelo de conmutación Hardware-in-the-Loop., Este trabajo ha sido soportado por el Gobierno de España a través del Proyecto PID2021-122821NB-I00 financiado por MICIU/AEI/10.13039/501100011033 y FEDER/UE, y por la Generalitat de Catalunya a través del Proyecto 2021 SGR 00376., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A two-level hysteresis-based sliding mode control for three-level single-phase inverters

  • Repecho del Corral, Víctor|||0000-0003-0584-5443
  • Borràs, Abel
  • Biel Solé, Domingo|||0000-0002-0364-7681
© 2025 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this article, we present a single-phase inverter controlled by a three-level sliding mode control. A simple first order sliding mode is designed to regulate the output voltage and it is implemented through a symmetrical two-level hysteresis band comparator. The hysteresis band of the comparator is dynamically adjusted to bound the switching frequency of the inverter. As a result, the desired voltage tracking is achieved and no average error is induced at the output. The article includes numerical simulation and experimental results carried out in a 1.2 kW prototype that confirm the good performance of the designed control in terms of tracking error and harmonic distortion of the output voltage. The proposal has been tested with input voltage variations, transients of resistive loads and with a nonlinear load showing the expected robustness., This work was supported in part by the Government of Spain through the Agencia Estatal de Investigación Project under Grant PID2021-122821NB-I00 and in part by the Generalitat de Catalunya through the Project 2021 under Grant SGR 00376. Recommended for publication by Associate Editor J. He.(Corresponding author: Víctor Repecho.), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Symbolic and user-friendly geometric algebra routines (SUGAR) for computations in Matlab

  • Velasco García, Manel|||0000-0002-0764-3063
  • Zaplana Agut, Isiah|||0000-0002-0862-3240
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Martí Colom, Pau|||0000-0002-5189-0782
Geometric Algebra (GA) provides a unified, compact mathematical framework for geometric computing, simplifying relations typically handled with more complex tools like matrix multiplication. In fields like robotics, GA replaces conventional coordinate-based approaches with the multiplication of special elements called rotors, offering greater efficiency. Despite its advantages, GA’s complexity and the lack of symbolic tools hinder its broader adoption among applied mathematicians and engineers. To address this, this article introduces Symbolic and User-friendly Geometric Algebra Routines (SUGAR), an open source Matlab toolbox. SUGAR streamlines GA usage in Matlab through a collection of user-friendly functions that support both numeric and symbolic computations, even in high-dimensional algebras. Designed for applied mathematics and engineering, it enables intuitive manipulation of geometric elements and transformations in two- and three-dimensional projective and conformal GAs, consistent with established computational methods. Moreover, SUGAR manages multivector functions such as exponential, logarithmic, sinusoidal, and cosine operations, enhancing its applicability in domains like robotics, control systems, and power electronics. Finally, this article also presents three validation examples across these fields, showcasing SUGAR’s practical utility in solving real-world engineering and applied mathematics problems., The work of I. Zaplana was partially supported by the Spanish National Project PID2020-114819GB-I00 funded by MI- CIU/AEI/10.13039/501100011033 and by the Generalitat de Catalunya through the Project 2021 SGR 00375. The work of A. Dòria-Cerezo was partially supported by the Spanish National Project PID2021-122821NB-I00 funded by MI- CIU/AEI/10.13039/501100011033 and ERDF/EU and by the Generalitat de Catalunya through the Project 2021 SGR 00376. M. Velasco, J. Duarte, and P. Martí were partially supported by the Spanish National Project PID2021-122835OB-C21 funded by MICIU/AEI/10.13039/501100011033., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Optimal recharge sequencing in multi-AGV systems: A mixed ILP approach

  • Lo Iudice, Francesco
  • Olm Miras, Josep Maria|||0000-0003-4925-9251
  • Suárez Feijóo, Raúl|||0000-0002-3853-7095
Battery level is a critical issue in AGV transportation systems, as AGVs cannot run out of power while operating. Hence, at some point they will be forced to stop and recharge at any of the charging stations available in the warehouse. The question that immediately arises is where, and when, to recharge in an optimal way. Assuming that an AGV has already been assigned a task sequence consisting of visiting a number of working stations, stops at charging stations should be optimally inserted. Here, we do so by minimizing the total tour time, including recharges. Recently, this problem was cast as a mixed integer nonlinear program that also included linear and nonlinear constraints. We recast this problem into a mixed integer linear program under linear constraints, which allows to find an exact solution. Moreover, we derive a procedure to reduce the number of variables of the problem. We also show that, when a charging station is visited, bringing the level of charge to the maximum allowed is optimal except for the case where the tour can be completed without other stops. Finally, we present a stochastic formulation of the problem to consider the presence of multiple AGVs in the layout, which may affect the time spent by AGVs at charging stations due to queuing and, consequently, the optimal solution. Interestingly, the linear formulation of the problem allows to fully characterize the optimal solution as a function of the expected occupancies of the charging stations., The work of Josep M. Olm was partially supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376, and the Industrial Doctorate Project 2021 DI 16. The work of Raúl Suárez was partially supported by the Government of Spain through the Project PID2020-114819GB-I00 funded by MICIU/AEI/10.13039/5011000 11033 and ERDF/EU, and by the Generalitat de Catalunya through the Industrial Doctorate Project 2021 DI 16.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

PI Passivity-based control of a stand-alone three-phase current source inverter

  • Boira Pujol, Pau|||0009-0004-0674-2889
  • Ortega Martínez, Romeo
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Griñó Cubero, Robert|||0000-0001-6045-4600
This paper presents the design of a Proportional-Integral Passivity-based Controller (PI-PBC) for a current source inverter feeding a resistive load. Thanks to the definition of a new passive output, the closed-loop system is shown to be globally asymptotically stable. This result solves the internal stability problem reported for these power converters. To robustify the control algorithm, the paper also includes the design of a parameter estimation scheme for the parasitic resistances and the load conductance. Numerical simulations are carried out to validate the control algorithm. The simulation stage compares the behaviour using the averaged model of the power converter and a more realistic switching model, including the three-phase implementation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Improved dynamic resource reservation-based AGV traffic control with optimized task allocation

  • Verma, Parikshit
  • Olm Miras, Josep Maria|||0000-0003-4925-9251
  • Suárez Feijóo, Raúl|||0000-0002-3853-7095
  • Toldrà Fernández, Pol
© 2024 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, Traffic management of multi-AGV fleets through improved dynamic resource reservation (IDRR) has been recently proven to be an interesting alternative within zone control-based approaches in terms of time completion efficiency in in-house transportation tasks. In this paper, preliminary results show that the combination of IDRR with PRIM allocation, a classical market-based task allocation strategy, yields a significant reduction of finishing times in a standard benchmark problem. Hence, further improvements are to be expected from deeper suitability analyses plus better tailored adaptations of optimal task allocation algorithms to zone control-based fleet management systems, and in particular to IDRR., P. Verma was supported by the Generalitat de Catalunya Project 2021 DI 16. J.M. Olm was partially supported by the Government of Spain Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya Projects 2021 SGR 00376 and 2021 DI 16. R. Suarez was partially supported by the ´ Government of Spain Project PID2020-114819GB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya Project 2021 DI 16., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Complex sliding averaging control for three-phase power converters

  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Boira Pujol, Pau|||0009-0004-0674-2889
  • Repecho del Corral, Víctor|||0000-0003-0584-5443
  • Biel Solé, Domingo|||0000-0002-0364-7681
This article addresses the implementation of complex-valued sliding mode controllers in three-phase power converters. The work includes the design and experimental assessment of two different strategies. The methods provide easy-to-code algorithms with a low computational burden, retain the sliding mode properties as robustness and fast transient response, and do not require any additional processing often used to decouple the dynamics of the three-phase system. The article includes the description of the algorithms and a detailed analysis of the proposed implementations. In addition, the performance of the methods is compared in numerical simulations, and the algorithms are experimentally tested in a three-phase inverter. The advantages of the proposed approaches, with respect to traditional sliding mode controllers, are that they do not require any decoupling stage, are easy to implement, and use zero vectors., This work was supported in part by the Government of Spain through the Project PID2021-122821NB-I00 under Grant MI-CIU/AEI/10.13039/ 501100011033 and ERDF/EU, and in part by the Generalitat de Catalunya through the Project 2021 SGR 00376. (Corresponding author: Arnau Dòria-Cerezo.), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Introducing modeling, analysis, and control of three-phase electrical systems using geometric algebra

  • Velasco García, Manel|||0000-0002-0764-3063
  • Zaplana Agut, Isiah|||0000-0002-0862-3240
  • Dòria Cerezo, Arnau|||0000-0001-9352-066X
  • Duarte Mejía, Josué Neftali
  • Martí Colom, Pau|||0000-0002-5189-0782
© 2025 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This article introduces a novel framework based on geometric algebra (GA) for the modeling, analysis, and control of three-phase electrical systems, with a focus on unbalanced scenarios. The proposed approach utilizes GA to represent these systems using simplified single-input/single-output (SISO) models, significantly reducing their mathematical complexity while maintaining accuracy. The framework introduces GA-valued transfer functions (GA-TFs), enabling the extension of well-established multivariable (MIMO) techniques, such as Youla-Kucera parameterization, into the GA domain as an illustrative example. This demonstrates the adaptability of classical tools within the new algebra. The validity and potential of the approach are showcased through numerical examples of balanced and unbalanced systems, as well as physical implementations in a laboratory setup. The results confirm that GA provides a robust and scalable foundation for simplifying the analysis and control of three-phase systems, paving the way for future theoretical and practical advancements., Received 13 June 2024; revised 16 September 2024, 9 December 2024, and 31 January 2025; accepted 8 March 2025. Date of publication 2 May 2025; date of current version 2 October 2025. The work of Manel Velasco, Josue Duarte, and Pau Mart ı was supported in part by Spanish National Project PID2021-122835OB-C21 under Grant MICIU/AEI/10.13039/501100011033; Isiah Zaplana was supported in part by Spanish National Project PID2020-114819GB-I00 under Grant MICIU/AEI/10.13039/501100011033; Arnau Doria-Cerezo was supported in part by Spanish National Project PID2021-122821NB-I00 under Grant MICIU/AEI/10.13039/501100011033 and ERDF/EU, and in part by the Generalitat de Catalunya through the Project 2021 SGR 00376. (Corresponding author: Manel Velasco.), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

DC interface impedance shaping for DC/AC grid forming converters in railway applications

  • Huerta Sánchez, Francisco
  • del Toro Zarza, José Manuel
  • Bueno Peña, Emilio José
  • Griñó Cubero, Robert|||0000-0001-6045-4600
  • Cóbreces Álvarez, Santiago
Among the different groups of stability issues that railway systems have to face are the electrical resonance instability phenomena. Within this group, one of the possible instability problems that appear is due to the constant power load (CPL) behavior of the traction and the auxiliary power system (APS) converters. This behavior interacts negatively with the variable impedance of the catenary and can cause catenary voltage fluctuations and compromise the stability of the railway line. In order to solve this problem, this paper proposes the use of a structured H 8 synthesis to design an ac voltage controller for the APS converter. The algorithm models the dc input admittance of the converter addressing three objectives: catenary stability, tracking of the ac output voltage reference, and robustness against unmodeled uncertainties. Experimental results with different types of loads (resistive and/or induction machine loads) demonstrate its compliance with railway standards and the modeling of the specified admittance., This work was supported in part by BRONTE Project under Grant SBPLY/21/180501/000147; in part by the Junta de Comunidades de Castilla La Mancha and European Union (EU) through European Regional Development Fund (ERDF); in part by ASTRAPE through the Comunidad de Madrid in the Framework of the Multiannual Agreement with the Universidad de Alcalá in the line of Action “Stimulus to the Research of Young Doctors,” within the V Plan Regional de Investigación Científica e Innovación Tecnológica (PRICIT) Framework Program under Project CM/JIN/2021-019; and in part by ERDF/EU under Project OPEMRES TED2021-130610B-C21, Project CRESIPS-PE PID2021-125628OB-C22, and Project MICIU/AEI/10.13039/501100011033. The work of Robert Griñó was supported by ERDF/EU under Project PID2021-122821NB-I00 and Project MICIU/AEI/10.13039/501100011033 and in part by the Generalitat de Catalunya under Project 2021 SGR 00376., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Novel electric arc current emulation system for low-voltage grids

  • Dávila, Asier
  • Otero Olavarrieta, Alberto
  • Planas, Estefanía
  • Cortajarena Echevarría, José Antonio
  • Arias Pujol, Antoni
An electric arc is a common distribution grid error, even more so with the use of electric vehicles and renewable energy sources that increase the likelihood of grid errors. Several control systems and strategies are under development to minimize electric-arc faults and to guarantee reliable grid performance. All the control strategies must be validated through emulations of the different fault modes at laboratory scale where there is no risk to either the researchers or the facilities. In this study, a novel system is proposed for the emulation of electric arc current waveforms, based on both real measurements and equation-based modeling. The proposed modular system provides the capability to emulate different levels of arcing currents. Validation of the system was demonstrated, in view of the design, the underlying theoretical analysis, and a set of control system simulations and experiments., This work was supported in part by the Government of the Basque Country within the fund for research groups of the Basque University system IT1440-22, by the Agencia Estatal de Investigación within the project PID2021-122821NB-I00, by the Generalitat de Catalunya within the project 2021 SGR 00376, and by the research project PT10709 funded by i-DE Redes Inteligentes S.A.U. through its Global Smart Grids Innovation Hub. Open Access funding provided by the University of Basque Country UPV/EHU., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The Ohm’s Law for (non-symmetric) three-phase three-wire electrical circuits: from a complex-valued to a geometric algebra approach

  • Dòria Cerezo, Arnau
  • Velasco García, Manel
  • Zaplana Agut, Isiah
  • Martí Colom, Pau
This paper introduces the modelling of three-phase electrical systems using the Geometric Algebra approach and is compared with the complex-valued framework in the case of non-symmetrical conditions. The main benefit of the geometric algebra framework is the possibility of representing the dynamics of unbalanced scenarios by a single-input, single-output relationship. The paper presents step-by-step, building the geometric impedance and revisiting Ohm’s law, and compares the complex-valued modelling widely used in balanced three-phase circuits., This work was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021- 122821NB-I00 and by the Generalitat de Catalunya, Spain through the Projects 2021-SGR-00098, 2021-SGR-00375 and 2021-SGR00376., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Introducing modeling, analysis, and control of three-phase electrical systems using geometric algebra

  • Velasco García, Manel
  • Zaplana Agut, Isiah
  • Dòria Cerezo, Arnau
  • Duarte Mejía, Josué Neftali
  • Martí Colom, Pau
© 2025 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This article introduces a novel framework based on geometric algebra (GA) for the modeling, analysis, and control of three-phase electrical systems, with a focus on unbalanced scenarios. The proposed approach utilizes GA to represent these systems using simplified single-input/single-output (SISO) models, significantly reducing their mathematical complexity while maintaining accuracy. The framework introduces GA-valued transfer functions (GA-TFs), enabling the extension of well-established multivariable (MIMO) techniques, such as Youla-Kucera parameterization, into the GA domain as an illustrative example. This demonstrates the adaptability of classical tools within the new algebra. The validity and potential of the approach are showcased through numerical examples of balanced and unbalanced systems, as well as physical implementations in a laboratory setup. The results confirm that GA provides a robust and scalable foundation for simplifying the analysis and control of three-phase systems, paving the way for future theoretical and practical advancements., Received 13 June 2024; revised 16 September 2024, 9 December 2024, and 31 January 2025; accepted 8 March 2025. Date of publication 2 May 2025; date of current version 2 October 2025. The work of Manel Velasco, Josue Duarte, and Pau Mart ı was supported in part by Spanish National Project PID2021-122835OB-C21 under Grant MICIU/AEI/10.13039/501100011033; Isiah Zaplana was supported in part by Spanish National Project PID2020-114819GB-I00 under Grant MICIU/AEI/10.13039/501100011033; Arnau Doria-Cerezo was supported in part by Spanish National Project PID2021-122821NB-I00 under Grant MICIU/AEI/10.13039/501100011033 and ERDF/EU, and in part by the Generalitat de Catalunya through the Project 2021 SGR 00376. (Corresponding author: Manel Velasco.), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Dual active bridge simultaneous input admittance passivity shaping and reference tracking using low order H-infinity control

  • Pérez Ruiz, Juan José
  • Santamargarita Mayor, Daniel
  • Molinero Blanco, David
  • Huerta Sánchez, Francisco
  • Pizarro Pérez, Daniel
  • Cóbreces Álvarez, Santiago
  • Griñó Cubero, Robert
© 2024 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, This paper presents a design methodology for the output voltage control loop of a dual active bridge (DAB). It is based on fixed-order H8 non-smooth synthesis combined with passivity restrictions over closed-loop impedance transfer function, known to have a critical impact on system voltage stability. The proposal inherits the advantages of modern techniques, making use of simple frequential weighting-based design and plant dynamical complexity black-boxing, while keeping controller complexity low., This work has been funded by BRONTE project (SBPLY/21/180501/000147), by the Junta de Comunidades de Castilla La Mancha and the European Union through the European Regional Development Fund; ASTRAPE project (CM/JIN/2021-019), financed by the Comunidad de Madrid in the framework of the Multiannual Agreement with the Universidad de Alcalá in the line of action ”Stimulus to the Research of Young Doctors”, within the V PRICIT framework program; and projects CRESIPSPE (PID2021-1256280B-C22) and OPEMRES (TED2021-130610B-C21) f inanced by Spanish Ministerio de Ciencia e Innovaci´ on, Agencia Estatal de Investigación and FEDER,UE 10.13039/501100011033. The work of Robert Griñ´ o was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021-122821NB-I00 and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Complex sliding averaging control for three-phase power converters

  • Dòria Cerezo, Arnau
  • Boira Pujol, Pau
  • Repecho del Corral, Víctor
  • Biel Solé, Domingo
This article addresses the implementation of complex-valued sliding mode controllers in three-phase power converters. The work includes the design and experimental assessment of two different strategies. The methods provide easy-to-code algorithms with a low computational burden, retain the sliding mode properties as robustness and fast transient response, and do not require any additional processing often used to decouple the dynamics of the three-phase system. The article includes the description of the algorithms and a detailed analysis of the proposed implementations. In addition, the performance of the methods is compared in numerical simulations, and the algorithms are experimentally tested in a three-phase inverter. The advantages of the proposed approaches, with respect to traditional sliding mode controllers, are that they do not require any decoupling stage, are easy to implement, and use zero vectors., This work was supported in part by the Government of Spain through the Project PID2021-122821NB-I00 under Grant MI-CIU/AEI/10.13039/ 501100011033 and ERDF/EU, and in part by the Generalitat de Catalunya through the Project 2021 SGR 00376. (Corresponding author: Arnau Dòria-Cerezo.), Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Symbolic and user-friendly geometric algebra routines (SUGAR) for computations in Matlab

  • Velasco García, Manel
  • Zaplana Agut, Isiah
  • Dòria Cerezo, Arnau
  • Martí Colom, Pau
Geometric Algebra (GA) provides a unified, compact mathematical framework for geometric computing, simplifying relations typically handled with more complex tools like matrix multiplication. In fields like robotics, GA replaces conventional coordinate-based approaches with the multiplication of special elements called rotors, offering greater efficiency. Despite its advantages, GA’s complexity and the lack of symbolic tools hinder its broader adoption among applied mathematicians and engineers. To address this, this article introduces Symbolic and User-friendly Geometric Algebra Routines (SUGAR), an open source Matlab toolbox. SUGAR streamlines GA usage in Matlab through a collection of user-friendly functions that support both numeric and symbolic computations, even in high-dimensional algebras. Designed for applied mathematics and engineering, it enables intuitive manipulation of geometric elements and transformations in two- and three-dimensional projective and conformal GAs, consistent with established computational methods. Moreover, SUGAR manages multivector functions such as exponential, logarithmic, sinusoidal, and cosine operations, enhancing its applicability in domains like robotics, control systems, and power electronics. Finally, this article also presents three validation examples across these fields, showcasing SUGAR’s practical utility in solving real-world engineering and applied mathematics problems., The work of I. Zaplana was partially supported by the Spanish National Project PID2020-114819GB-I00 funded by MI- CIU/AEI/10.13039/501100011033 and by the Generalitat de Catalunya through the Project 2021 SGR 00375. The work of A. Dòria-Cerezo was partially supported by the Spanish National Project PID2021-122821NB-I00 funded by MI- CIU/AEI/10.13039/501100011033 and ERDF/EU and by the Generalitat de Catalunya through the Project 2021 SGR 00376. M. Velasco, J. Duarte, and P. Martí were partially supported by the Spanish National Project PID2021-122835OB-C21 funded by MICIU/AEI/10.13039/501100011033., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Voltage regulation in an interleaved circular chain sliding mode controlled multiphase converter

  • Biel Solé, Domingo
  • Arroyo de Fàbregas, Adrià
  • Repecho del Corral, Víctor
In this article a multiphase synchronous buck converter controlled by a sliding mode control (SMC) in a circular chain control (CCC) configuration is presented. The proposed switching functions with the CCC architecture ensure a robust output voltage regulation when facing changes in the load or the input voltage, while providing current equalization among the phases. The novelty of the work is the simple control structure based on a first order SMC implemented by means of hysteresis-band comparators, requiring no external signals or additional hardware to lead the system to an interleaving operation, obtaining a harmonic cancellation that allows the size reduction not only of the output capacitor but also of the inductors. It is proved that, in the steady state, the switching function exhibits a periodic solution with a period equal to the switching period. Besides, the steady-state switching frequency expression as a function of the hysteresis bandwidth is derived. The work includes the analytical analysis of the proposed solution, a set of numerical simulations and, finally, an experimental validation. The numerical and experimental results confirm the predicted good performance of the proposed control., This work was partially supported by the Government of Spain through the Agencia Estatal de Investigación Project PID2021- 122821NB-I00 and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Improved dynamic resource reservation-based AGV traffic control with optimized task allocation

  • Verma, Parikshit
  • Olm Miras, Josep Maria
  • Suárez Feijóo, Raúl
  • Toldrà Fernández, Pol
© 2024 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, Traffic management of multi-AGV fleets through improved dynamic resource reservation (IDRR) has been recently proven to be an interesting alternative within zone control-based approaches in terms of time completion efficiency in in-house transportation tasks. In this paper, preliminary results show that the combination of IDRR with PRIM allocation, a classical market-based task allocation strategy, yields a significant reduction of finishing times in a standard benchmark problem. Hence, further improvements are to be expected from deeper suitability analyses plus better tailored adaptations of optimal task allocation algorithms to zone control-based fleet management systems, and in particular to IDRR., P. Verma was supported by the Generalitat de Catalunya Project 2021 DI 16. J.M. Olm was partially supported by the Government of Spain Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya Projects 2021 SGR 00376 and 2021 DI 16. R. Suarez was partially supported by the ´ Government of Spain Project PID2020-114819GB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya Project 2021 DI 16., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimal recharge sequencing in multi-AGV systems: A mixed ILP approach

  • Lo Iudice, Francesco
  • Olm Miras, Josep Maria
  • Suárez Feijóo, Raúl
Battery level is a critical issue in AGV transportation systems, as AGVs cannot run out of power while operating. Hence, at some point they will be forced to stop and recharge at any of the charging stations available in the warehouse. The question that immediately arises is where, and when, to recharge in an optimal way. Assuming that an AGV has already been assigned a task sequence consisting of visiting a number of working stations, stops at charging stations should be optimally inserted. Here, we do so by minimizing the total tour time, including recharges. Recently, this problem was cast as a mixed integer nonlinear program that also included linear and nonlinear constraints. We recast this problem into a mixed integer linear program under linear constraints, which allows to find an exact solution. Moreover, we derive a procedure to reduce the number of variables of the problem. We also show that, when a charging station is visited, bringing the level of charge to the maximum allowed is optimal except for the case where the tour can be completed without other stops. Finally, we present a stochastic formulation of the problem to consider the presence of multiple AGVs in the layout, which may affect the time spent by AGVs at charging stations due to queuing and, consequently, the optimal solution. Interestingly, the linear formulation of the problem allows to fully characterize the optimal solution as a function of the expected occupancies of the charging stations., The work of Josep M. Olm was partially supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376, and the Industrial Doctorate Project 2021 DI 16. The work of Raúl Suárez was partially supported by the Government of Spain through the Project PID2020-114819GB-I00 funded by MICIU/AEI/10.13039/5011000 11033 and ERDF/EU, and by the Generalitat de Catalunya through the Industrial Doctorate Project 2021 DI 16., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Control y análisis de la dinámica cero en inversores trifásicos de fuente de corriente mediante un modelo de variables de estado complejas

  • Rahimi, Leila
  • Dòria Cerezo, Arnau
  • Griñó Cubero, Robert
Este trabajo analiza la dinámica cero de inversores de fuente de corriente trifásicos alimentados desde una fuente de tensión y conectados a una carga resistiva local o a la red eléctrica. El análisis de la dinámica cero concluye que, cuando la fuente de alimentación se modela a partir de su circuito equivalente de Thévenin, se producen problemas de estabilidad que se manifiestan en la corriente del bus cc, si el lazo de control fuerza un buen seguimiento de la tensión de salida. El artículo incluye el diseño de un controlador de bucle anidado alternativo que supera la inestabilidad interna de la corriente del inductor, Este trabajo ha sido financiado en parte por el Gobierno de España a través del programa Agencia Estatal de Investigación en Proyecto PID2021-122821NB-I00 y por la Generalitat de Catalunya a través del Proyecto 2021 SGR 00376. El trabajo de L. Rahimi está financiado por la beca 2022-FPU-UPC-36., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Sliding-mode control in the dq-reference frame for a three-phase CSI feeding an isolated load

  • Boira Pujol, Pau
  • Dòria Cerezo, Arnau
  • Griñó Cubero, Robert
© 2026 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper proposes a sliding-mode controller for a single-stage, three-phase current source inverter supplying an isolated load. The control architecture, derived from the dq model of the converter, features two cascaded loops: an inner slidingmode control loop that regulates the q-axis voltage component together with the DC current, and an outer proportional-integral control loop for the d-axis. In contrast to traditional linear methods, the proposed sliding-mode control enhances system robustness and transient performance, while the cascaded scheme overcomes the inherent non-minimum phase behaviour of boosttype converters. The effectiveness of the proposed control strategy is verified through numerical simulations, and its practical feasibility is demonstrated experimentally using a Hardware-in-the-Loop (HIL) platform., This work was supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

PI Passivity-based control of a stand-alone three-phase current source inverter

  • Boira Pujol, Pau
  • Ortega Martínez, Romeo
  • Dòria Cerezo, Arnau
  • Griñó Cubero, Robert
This paper presents the design of a Proportional-Integral Passivity-based Controller (PI-PBC) for a current source inverter feeding a resistive load. Thanks to the definition of a new passive output, the closed-loop system is shown to be globally asymptotically stable. This result solves the internal stability problem reported for these power converters. To robustify the control algorithm, the paper also includes the design of a parameter estimation scheme for the parasitic resistances and the load conductance. Numerical simulations are carried out to validate the control algorithm. The simulation stage compares the behaviour using the averaged model of the power converter and a more realistic switching model, including the three-phase implementation., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

DC interface impedance shaping for DC/AC grid forming converters in railway applications

  • Huerta Sánchez, Francisco
  • del Toro Zarza, José Manuel
  • Bueno Peña, Emilio José
  • Griñó Cubero, Robert
  • Cóbreces Álvarez, Santiago
Among the different groups of stability issues that railway systems have to face are the electrical resonance instability phenomena. Within this group, one of the possible instability problems that appear is due to the constant power load (CPL) behavior of the traction and the auxiliary power system (APS) converters. This behavior interacts negatively with the variable impedance of the catenary and can cause catenary voltage fluctuations and compromise the stability of the railway line. In order to solve this problem, this paper proposes the use of a structured H 8 synthesis to design an ac voltage controller for the APS converter. The algorithm models the dc input admittance of the converter addressing three objectives: catenary stability, tracking of the ac output voltage reference, and robustness against unmodeled uncertainties. Experimental results with different types of loads (resistive and/or induction machine loads) demonstrate its compliance with railway standards and the modeling of the specified admittance., This work was supported in part by BRONTE Project under Grant SBPLY/21/180501/000147; in part by the Junta de Comunidades de Castilla La Mancha and European Union (EU) through European Regional Development Fund (ERDF); in part by ASTRAPE through the Comunidad de Madrid in the Framework of the Multiannual Agreement with the Universidad de Alcalá in the line of Action “Stimulus to the Research of Young Doctors,” within the V Plan Regional de Investigación Científica e Innovación Tecnológica (PRICIT) Framework Program under Project CM/JIN/2021-019; and in part by ERDF/EU under Project OPEMRES TED2021-130610B-C21, Project CRESIPS-PE PID2021-125628OB-C22, and Project MICIU/AEI/10.13039/501100011033. The work of Robert Griñó was supported by ERDF/EU under Project PID2021-122821NB-I00 and Project MICIU/AEI/10.13039/501100011033 and in part by the Generalitat de Catalunya under Project 2021 SGR 00376., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Four-Leg voltage source converter with independent phase control for ground fault compensation

  • Dávila, Asier
  • Komrska, Tomáš
  • Arias Pujol, Antoni
  • Cortajarena Echevarría, José Antonio
  • Planas, Estefanía
  • Peroutka, Zdenek
Electrical faults are a frequent occurrence in medium voltage (MV) distribution grids, often affecting or completely interrupting the electrical supply. Among these, single-phase faults are the most common type and passive elements such as Peterson coils have been traditionally employed to mitigate their impact and maintain a reliable power supply. However, these solutions come with inherent drawbacks, including limited flexibility and functionality, which hinder their effectiveness in dynamic grid scenarios. This work presents a novel system designed to ensure high-quality power supply continuity before, during, and after single-phase faults. The proposed approach uses already installed four-leg power converters in the grid, eliminating the need for additional passive equipment. A new control strategy is developed in the natural abc reference frame, which enables the use of classical control techniques in the MIMO system and simplifies the analysis of the output voltage loops without changing the reference frame. Simulations and experimental results confirm that the proposed control framework effectively compensates for faults and maintains grid stability, improving fault resilience in MV distribution networks., This research has been partially supported by the Technology Agency of the Czech Republic, project TN02000025 National Center for Energy II, partially supported the Department of Education of the Basque Government within the fund for research groups of the Basque university system IT1440- 22, partially supported by the Government of Spain through the Project PID2021-122821NB-I00 funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU, and by the Generalitat de Catalunya through the Project 2021 SGR 00376. The authors wish to express their gratitude to Gipuzkoako Foru Aldundia for the project Etorkizuna Eraikiz 2024–2025. Open Access funding provided by University of Basque Country., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Novel slow–fast behaviour in an oscillator driven by a frequency-switching force

  • Bonet Revés, Carles
  • Jeffrey, Mike R.
  • Martín de la Torre, Pablo
  • Olm Miras, Josep Maria
When an oscillator switches abruptly between different frequencies, there is some ambiguity in deciding how the system should be modelled at the switch. Here we describe two seemingly natural models of a switch in a simple periodically-forced harmonic oscillator, which disagree starkly in their predictions of its long time behaviour. Attempting to resolve the disagreement by ‘regularizing’ the switch not only preserves the disagreement, but shows it increases with time. One of the models corresponds to a conventional ‘Filippov’ description of a nonsmooth system, while the second exhibits a structure that irreversibly ages, developing a number of novel multi-scale behaviours that we believe have not been reported before. These include slow–fast staircases, novel mixed-mode oscillations, and a synchronized canard explosion. These features are proven to exist using asymptotic analysis, but as they involve a slow–fast time-scale separation that increases with time, they lie beyond the reach of numerical methods., The authors thank DD Novaes for helpful conversations regarding the discontinuous system. PM was partially supported by the Spanish MINECO-FEDER Grant PID2021-123968NB-I00 and the Catalan grant 2017SGR1049. This work is also supported by the Spanish State Research Agency, through the Severo Ochoa and María de Maeztu Program for Centers and Units of Excellence in R&D (CEX2020-001084-M). CB was partly supported by the Spanish MINECO-FEDER Grant PGC2018-098676-B-100 (AEI/FEDER/UE) and Catalan grant 2017SGR1049. JMO was partially supported by the Spanish Agencia Estatal de Investigación Project PID2021-122821NB-I00., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Control PI basado en pasividad para un inversor trifásico de fuente de corriente alimentando una carga local

  • Boira Pujol, Pau
  • Ortega, Romeo
  • Dòria Cerezo, Arnau
  • Griñó Cubero, Robert
Este artículo presenta el diseño de un controlador Proporcional-Integral basado en pasividad para un inversor trifásico de fuente de corriente alimentando una carga resistiva. Gracias a la definición de una nueva salida pasiva, se demuestra que el sistema en lazo cerrado es globalmente y asintóiticamente estable. Este resultado resuelve el problema de estabilidad interna señalado en trabajos anteriores para estos convertidores de potencia. Para reforzar el algoritmo de control, el artículo también incluye el diseño de un esquema de estimación de parámetros para las resistencias parásitas y la conductancia de carga. Se han realizado simulaciones numéricas para validar el algoritmo de control. Asimismo, se compara el comportamiento utilizando el modelo promediado del convertidor de potencia y un modelo de conmutación Hardware-in-the-Loop., Este trabajo ha sido soportado por el Gobierno de España a través del Proyecto PID2021-122821NB-I00 financiado por MICIU/AEI/10.13039/501100011033 y FEDER/UE, y por la Generalitat de Catalunya a través del Proyecto 2021 SGR 00376., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A two-level hysteresis-based sliding mode control for three-level single-phase inverters

  • Repecho del Corral, Víctor
  • Borràs, Abel
  • Biel Solé, Domingo
© 2025 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this article, we present a single-phase inverter controlled by a three-level sliding mode control. A simple first order sliding mode is designed to regulate the output voltage and it is implemented through a symmetrical two-level hysteresis band comparator. The hysteresis band of the comparator is dynamically adjusted to bound the switching frequency of the inverter. As a result, the desired voltage tracking is achieved and no average error is induced at the output. The article includes numerical simulation and experimental results carried out in a 1.2 kW prototype that confirm the good performance of the designed control in terms of tracking error and harmonic distortion of the output voltage. The proposal has been tested with input voltage variations, transients of resistive loads and with a nonlinear load showing the expected robustness., This work was supported in part by the Government of Spain through the Agencia Estatal de Investigación Project under Grant PID2021-122821NB-I00 and in part by the Generalitat de Catalunya through the Project 2021 under Grant SGR 00376. Recommended for publication by Associate Editor J. He.(Corresponding author: Víctor Repecho.), Peer Reviewed, Postprint (author's final draft)