Pasar al contenido principal

ECODISEÑO DE MEMBRANAS POLIMERICAS PLATAFORMA QUE COMBINAN PROPIEDADES DE LIQUIDO Y SOLIDO Y SUS APLICACIONES

PID2022-143310OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2022
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Self-supported FeCoNi(OH<inf>y</inf>)O<inf>x</inf> oxy-hydroxide doped with Cr and Cu as robust low-loading catalyst for the alkaline oxygen evolution reaction

  • Ruiz Esquius, Jonathan
  • González-Ingelmo, María
  • López García, Miriam
  • Vigil Laruelo, Adrián
  • Santamaría Ramírez, Ricardo
  • Blanco Rodríguez, Clara
  • Rocha, Victoria G.
Self-supported FeCoNi(OHy)Ox oxy-hydroxides co-doped with Cr and Cu were obtained from a CrFeCoNiCu low ordered high entropy precursor synthesised by electrodeposition onto carbon cloth fibres (act-CrFeCoNiCu/CC). For comparison a dopant-free FeCoNi(OHy)Ox catalyst (act-FeCoNi/CC) was also synthesised following the same route. No heat treatment was performed to retain their low ordered structure. When assessed towards the oxygen evolution reaction (OER) in alkaline electrolyte, act-CrFeCoNiCu/CC and act-FeCoNi/CC catalyst reached a comparable current density of 10 mA cm−2 at ca. 1.6 VRHE (η10 of 380–390 mV). Nevertheless, Cr and Cu co-doping translated into improved stability. Evident degradation was observed during OER for act-FeCoNi/CC after 12 h operating at 100 mA cm−2, whereas no signs of degradation were detected for act-CrFeCoNiCu/CC under the same reaction conditions. The latter catalyst even delivered a constant potential for 160 h at 50 mA cm−2 aided to the stabilizing effect of Cr and Cu co-doping., Jonathan Ruiz Esquius (of ComFuturo fellow) is supported by a fellowship from the Fundación General CSIC's ComFuturo programme which has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 101034263. The authors would like to also acknowledge the PID2022-143310OB-I00 and CNS2022-135465 projects funded by MICIN/AEI/10.13039/501100011033/FEDER, EU. M. López García and M. González-Ingelmo PhD thesis are funded by PRE2020-095966 and FICYT Severo Ochoa program BP20-168, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Porous membranes of polymer blends and their use as functional separators for electrochemical batteries

  • Gregorio, Víctor
  • Chang, J. H.
  • García, Nuria
  • Tiemblo, Pilar
This works explores the synthesis of a porous membrane concept combining two polymers: one with a structural role which constitutes the scaffold of the membrane, and the other with the capacity to form a polymer gel with ad-hoc liquids at the pores and surface of the membrane. After liquid infiltration, the structural polymer keeps the mechanical properties and dimensional stability of the membrane constant, i.e. no swelling, for long time periods, while the soluble polymer forms a gel at the pores and membrane surface. In this work, the goal of these membranes is that of a functional separator able to produce semisolid electrolytes by in-situ gel formation upon soaking with liquid electrolytes at electrochemical cells. This functional separator enables the formation of the semisolid electrolyte without modification of the electrochemical cells industrial processes, and avoiding the handling of UHMW gels at an industrial scale. Functional separators comprising polycarbonate (PC) as the structural scaffold and ultrahigh molecular weight (UHMW) polyethylene oxide (PEO) as the soluble polymer for in-situ gel formation are prepared by adapting the non-solvent induced phase separation (NIPS) process to the simultaneous coagulation of the two polymers. The polymer distribution, pore morphology depend on the experimental conditions, especially on the PC/PEO degree of mixing before coagulation. The polymer distribution permits the formation of PEO gel at the pores of the PC scaffold, thus combining the electrochemical properties of UHMW polymer gel electrolytes, with the chemical and mechanical resistance of PC. Moreover the presence of PEO enables the wetting of the PC scaffold (otherwise hydrophobic) with hydrophilic electrolytes such as aqueous ZnCl, the Zn eutectic acetamide Zn(TFSI) (ACE-Zn) and the chloroaluminate acetamidine-AlCl, selected in this work to showcase the separators’ versatility, which do not do not swell, break, or degrade after months soaked in the electrolytes. Symmetric Zn||Zn cells were built using the electrolyte ACE-Zn soaked in PC/PEO membranes (40 μm) and in a 100 μm glass fiber separator. While the latter short-circuited before 150 cycles, functional separators endured 300 cycles with no short-circuiting, proving the formation of the UHMW PEO gel at the functional separators and concomitant increase in cycling stability, highlighting the success of this approach., The authors wish to acknowledge financial support through the projects AMAPOLA H2020-EIC-FETPROACT-2019 G A. 951902 from EU Comission, SuSaNa ERA.NET" title = "http://M-ERA.NET">M-ERA.NET PCI 2022–132931 and PID2022-143310OB-I00 from the Ministry of Science, Innovation and Universities, Spain.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural features that control hydrophobicity generation on PLA surfaces

  • Hernández-Rivas, María
  • Martínez-Gómez, Aránzazu
  • Tiemblo, Pilar
  • García, Nuria
Controlling the wettability of polylactic acid (PLA) surfaces remains a compelling challenge, as this multifunctional biopolymer is widely used in diverse applications and constitutes one of the most employed polymers in additive manufacturing. However, it is often overlooked that PLA is not a single polymer but a family of polymers whose properties vary significantly with the content of the D-isomer. In this work, we aim to rationalize the influence of polymer chain structure on the surface wettability of films prepared from PLA. Five commercial PLA samples were studied to evaluate the influence of D-isomer content and molecular weight on their semicrystalline morphology. Based on these findings, the polymers were processed into films and subjected to a solvent treatment sequence with acetone and ethanol designed to promote crystallization and, consequently, generate surface roughness. The resulting topography and roughness parameters, characterized by profilometry, were correlated with the wettability regime developed on the surface, namely superhydrophobic or parahydrophobic. In addition, the mechanical stability of the rough structures and the durability of the hydrophobic behavior were assessed through friction and water immersion tests, respectively. The results highlight a direct relationship between the D-isomer content and the wetting behavior that can be induced on a PLA surface., The authors thank Spanish Ministry of Science for funding through the Project The authors thank Spanish Ministry of Science for funding through the Project PID2022–143310OB-I00 and FPI Grant PRE2020–094915 awarded to M.H-R and FPI Grant PRE2020–094915 awarded to M.H-R, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Na Battery Electrolytes Prepared by Dissolution of Commercial Polymers in NaPF 6 –Diglyme

  • Campo, Ángela
  • García, Nuria
  • López-Cudero, Ana
  • Hall, Aram
  • Younesi, Reza
  • Tiemblo, Pilar
The incorporation of small amounts of polymers into liquid electrolytes to produce gel electrolytes has many benefits. Decreasing, or even avoiding flow reduces accidents caused by leaks, allows for simpler and more flexible geometries and configurations, stabilizes electrochemical cycling, and may even permit the separate recycling of each cell component. Direct mixing of polymers with liquid electrolytes is very frequently possible, and it is a sustainable and scalable procedure that avoids evaporation stages and produces thermoreversible materials. In this work, some of the polymers most commonly used for gel electrolyte formation─polyvinylidene fluoride (PVDF), polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP), polyvinyl chloride (PVC), poly(methyl methacrylate) (PMMA), and poly(ethylene oxide) (PEO)─are employed to produce gels with the electrolyte NaPF6 1.1 m in diglyme, and their behavior and performance are described. All these polymers are soluble in the electrolyte, and the ultrahigh molecular weight (UHMW) PEO and the halogenated polymers are able to form self-standing gels at concentrations ranging from 5 to 10 wt %. The fluorinated polymer gels left standing in an Ar glovebox progressively become colored, turning almost black after one month, showing a lack of long-term chemical stability. PVC 10 wt % and UHMW PEO 5 wt % gels, however, become hard gels with no macroscopic phase separation and remain stable for periods of months. Their electrochemical stability against Na electrodes was tested, showing that the PVC gel is not stable, and only the UHMW PEO 5 wt % gels were further tested with Prussian white (PW) cathodes. The PEO gel electrolyte, without any physical separator, showed equivalent performance in PW||Na half-cells as the baseline electrolyte with a glass fiber separator, while also being self-standing and solid-like in consistency. The PEO gel electrolytes also showed applicability to PW||HC full cells. Moreover, after electrochemical testing, the coin cells with PEO gels were easily disassembled, and their components were recovered., The authors wish to acknowledge financial support from Project SuSaNa under G.A. N° 958174 (M-ERA.Net-3 Call2021), the Spanish Research Agency (PCI2022-132931), the Spanish Ministry of Science (PID2022-143310OB-I00), and CSIC PIE projects 202360E035 and 202460E102., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bottom-up formation of crystalline PEO/Na+scaffolds in NaPF6-Diglyme-PEO and the electrochemical properties of the resulting electrolytes

  • Campo, Ángela
  • García, Nuria
  • Hall, Aram
  • Younesi, Reza
  • Hosseinzadegan, Meghdad
  • Rehnlund Maibach, David
  • Tiemblo, Pilar
Ultrahigh Molecular Weight polyethylene oxide (UHMW PEO) and NaPF<inf>6</inf> diglyme produce solid electrolytes with chemical and electrochemical stability in Prussian White (PW)//Hard Carbon (HC) and Na//Al cells. Both the NaPF<inf>6</inf> concentration and the polymer content rule the rheology, and the mechanical and electrochemical properties of the electrolytes. The use of UHMW PEO allows to incorporate minimum concentrations with maximum rheological impact. The solid character is achieved by the formation of rigid scaffold consisting of PEO/Na+ crystalline complexes, which stops flow and provides a mechanical barrier between electrodes. To maximize the benefits of polymer addition, it is worthwhile to test formulations in which the concentration of Na+ and PEO are varied. This is because the PEO/Na+ crystalline complexes reduce the amount of mobile Na+ cations. Na+ complexation and crystalline phase distribution is studied by FTIR, XRD and DSC in NaPF<inf>6</inf> in diglyme solutions of concentration 0.9 to 1.5 m, and their solid electrolytes where PEO varies from 5 to 10 wt%. Ion mobility (conductivity and diffusivity) is studied in relation to their chemical composition and phase distribution, and their electrochemical behaviour is investigated in PW//HC and Na//Al cells. Cells with solid polymer electrolytes show remarkable performance even at room temperature and high current rate (1C)., The authors wish to acknowledge financial support from project SuSaNa under G.A. N 958174 (M-ERA.Net-3 Call2021), Spanish Research Agency (PCI2022-132931), and the Spanish Ministry of Science (PID2022-143310OB-I00) as well as the Swedish Energy Agency (P2021-90018) and the CSIC PIE projects 202360E035 and 202460E102. The NMR Service at ICTP-CSIC is acknowledged for the determination of diffusion coefficients., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the optimization of healing conditions for multifunctional recovery in natural rubber/polycaprolactone and natural rubber/polyethylene oxide thermoplastic elastomers

  • Raza, M. Hassan
  • Guastavino, Francesco
  • Della Giovanna, Laura
  • Torello, Eugenia
  • Mas-Giner, Itziar
  • Hernández-Rivas, María
  • Hernández, Marianella
  • Tiemblo, Pilar
Electrical insulation faces severe mechanical, electrical, thermal, and environmental stresses, where defects distort the local field and initiate partial discharges and compromise dielectric integrity, requiring costly repair or replacement. Self-healing insulation offers a route to extend service life by repairing damage in response to an external stimulus. In this study, self-healing thermoplastic elastomers (TPEs) were prepared by blending a natural rubber (NR) matrix, which provides good electrical insulation, with a thermoplastic healing phase like polycaprolactone (PCL) or polyethylene oxide (PEO). The TPEs were scratched initially, and self-healing protocol were applied at (70, 90, 110 °C) for (2, 4, 6 h) to mobilize the TPEs into the scratch for surface topography healing. Under optimal healing conditions, NR/PEO achieved more than 80% topographical recovery and surface restoration within 2 h at 90 °C, whereas NR/PCL required 3 h at 110 °C. FTIR-ATR showed that the healed NR/PEO scratch matched the composition of the virgin material to perform homogenous healing, and its dielectric breakdown strength was recovered. In contrast, the NR/PCL scratch remained enriched in PCL relative to the virgin state, and this compositional defect coincided with no dielectric recovery. These findings demonstrate that surface topographic closure alone does not guarantee restoration of dielectric functionality. Accordingly, this study proposes an experimental framework that couples optical profilometry, FTIR-ATR, and AC dielectric breakdown testing to integrate topographical, chemical, and functional recovery into a single assessment, enabling reliable evaluation and optimization of healing protocols for self-healing insulation systems., M.H.S acknowledges Grant PID2022-143107OB-I00 funded by ICIU/ AEI/10.13039/501100011033/FEDER, UE. P.T and M.H-R. thank Spanish Ministry of Science for funding through the Project PID2022–143310OB-I00 and FPI Grant PRE2020–094915 awarded to M.H-R., Peer reviewed