Pasar al contenido principal

ELECTRODOS NANOESTRUCTURADOS PARA PILAS DE COMBUSTIBLES DE OXIDOS SOLIDOS SIMETRICAS

RTI2018-093735-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE MALAGA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructured BaCo0.4Fe0.4Zr0.1Y0.1O3-δ cathodes with different microstructural architectures

  • Santos-Gómez, Lucía dos
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
This article belongs to the Special Issue 10th Anniversary of Nanomaterials—Recent Advances in Nanomaterials for Energy and Catalysis., Lowering the operating temperature of solid oxide fuel cells (SOFCs) is crucial to make this technology commercially viable. In this context, the electrode efficiency at low temperatures could be greatly enhanced by microstructural design at the nanoscale. This work describes alternative microstructural approaches to improve the electrochemical efficiency of the BaCo0.4Fe0.4Zr0.1Y0.1O3-δ (BCFZY) cathode. Different electrodes architectures are prepared in a single step by a cost-effective and scalable spray-pyrolysis deposition method. The microstructure and electrochemical efficiency are compared with those fabricated from ceramic powders and screen-printing technique. A complete structural, morphological and electrochemical characterization of the electrodes is carried out. Reduced values of area specific resistance are achieved for the nanostructured cathodes, i.e., 0.067 Ω·cm2 at 600 °C, compared to 0.520 Ω·cm2 for the same cathode obtained by screen-printing. An anode supported cell with nanostructured BCFZY cathode generates a peak power density of 1 W·cm−2 at 600 °C., This research was funded by Ministerio de Ciencia, Innovación y Universidades (Spain), grant number RTI2018-093735-B-I00 and UMA18-FEDERJA-033.Lucía dos Santos-Gómez thanks the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Intermediate-Temperature Electrochemical Performance of Air Electrodes for Solid Oxide Cells with Spray-Pyrolyzed Active Layers

  • Zapata-Ramírez, Víctor
  • Dos Santos-Gómez, Lucía
  • Mather, Glenn C.
  • Marrero-López, David
  • Pérez-Coll, Domingo
The potential of interactive layers of mixed-conducting oxides for improving the performance of air electrodes of solid oxide cells in the intermediate-temperature range is demonstrated. Active layers of CeGdO (CGO), CePrO (CPO), and SrFeMoO (SFM) with thickness in the range 200-400 nm are deposited on CGO-based electrolyte by spray pyrolysis, followed by deposition of a SFM/CGO composite air electrode by painting. The morphologies and phase composition of the active layers are examined by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy microanalysis. The electrochemical performance of the electrolyte-electrode assemblies is determined by impedance spectroscopy in the range 600-800 °C. Significant improvements in the performance of the electrode process and the geometrically normalized ohmic conductance are observed for the assembly with a CPO active layer with mixed-oxide-ionic-electronic conductivity, especially in the low-temperature range, attributable to extension of the surface path of the electrochemical reactions. The CGO intermediate layer also improves performance but to a lesser degree, most likely due to better ionic-current collection in comparison to the assemblies with either SFM as the active layer or no active layer., We acknowledge the “Fundacioń Domingo Martínez” (Ayuda a la Investigación 2017. Área de Materiales: celdas decombustible) and “Ministerio de Ciencia, Innovación y Universidades” (RTI2018-095088-B-I00 and RTI2018-093735-B-I00) for financial support. Collaboration between the research groups was facilitated by the “Red de Excelencia”program (MINECO, MAT2017-090695-REDT).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Investigation of PO43− oxyanion-doping on the properties of CaFe0.4Ti0.6O3−δ for potential application as symmetrical electrodes for SOFCs

  • Santos-Gómez, Lucía dos
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
  • Slater, Peter R.
CaTi0.6-xFe0.4PxO3-δ (0≤x ≤ 0.075) perovskite series are investigated as potential symmetrical electrodes for SOFCs. Pure phase compounds with a cubic perovskite structure (s.g. Pm3m) are obtained for x ≤ 0.025, while higher doping level leads to the formation of Ca10(PO4)6(OH)2 as secondary phase. The P-doped compounds are structurally stable under reducing atmosphere unlike the undoped phase. Conductivity values of the P-doped samples are slightly higher than that of the undoped one, i.e. 0.11 and 0.07 Scm−1 for CaTi0.575Fe0.4P0.025O3-δ and CaTi0.6Fe0.4O3-δ, respectively, at 750 °C in air. The performance of CaTi0.575Fe0.4P0.025O3-δ acting simultaneously as both anode and cathode was also tested in a symmetrical solid oxide fuel cell with a 240 μm thick YSZ electrolyte. Hence, these results show that PO43− units can be introduced into CaTi0.6Fe0.4O3-δ perovskite structure, having beneficial effects on the electrochemical performance and the phase stability., This work was supported by Ministerio de Ciencia, Innovación y Universidades through the RTI2018-093735-B-I00 and UMA18-FEDERJA-033 research projects (Spain). L. dos Santos-Gómez thanks to the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I). J.M. Porras-Vázquez thanks the University of Málaga for his funding., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Perspectives on Cathodes for Protonic Ceramic Fuel Cells

  • Mather, Glenn C.
  • Muñoz-Gil, Daniel
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Marrero-López, David
  • Pérez-Coll, Domingo
This article belongs to the Special Issue Recent Advances in Electrodes for Proton-Conducting Solid Oxide Fuel Cells., Protonic ceramic fuel cells (PCFCs) are promising electrochemical devices for the efficient and clean conversion of hydrogen and low hydrocarbons into electrical energy. Their intermediate operation temperature (500–800 °C) proffers advantages in terms of greater component compatibility, unnecessity of expensive noble metals for the electrocatalyst, and no dilution of the fuel electrode due to water formation. Nevertheless, the lower operating temperature, in comparison to classic solid oxide fuel cells, places significant demands on the cathode as the reaction kinetics are slower than those related to fuel oxidation in the anode or ion migration in the electrolyte. Cathode design and composition are therefore of crucial importance for the cell performance at low temperature. The different approaches that have been adopted for cathode materials research can be broadly classified into the categories of protonic–electronic conductors, oxide-ionic–electronic conductors, triple-conducting oxides, and composite electrodes composed of oxides from two of the other categories. Here, we review the relatively short history of PCFC cathode research, discussing trends, highlights, and recent progress. Current understanding of reaction mechanisms is also discussed., This work was funded by MICINN (Spain), grant numbers RTI2018-095088-B-I00 and RTI2018-093735-B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Recent progress in nanostructured electrodes for solid oxide fuel cells deposited by spray pyrolysis

  • Santos-Gómez, Lucía dos
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
Low-temperature solid oxide fuel cells (LT-SOFCs), operating below 650 °C, are attracting a great interest due to their long-term stability and potential application for stationary and portable power generation. Much effort is being devoted to investigating new electrode materials because the electrode polarization resistance remains a serious limitation to the performance. Nanostructured electrodes offer the possibility of increasing the SOFC efficiency at low temperatures. Among the different electrode preparation techniques, spray pyrolysis deposition is a versatile, economic and industrially scalable method to grow electrodes directly on the electrolyte, reducing preparation steps and time. Recent progresses in this field are summarized here, especially highlighting the wide variety of different microstructural strategies used to improve the electrode performance, i.e. nanocomposite cathodes graded cathodes, infiltrated cathodes and cathodes with active/functional layers. Finally, the current existing challenges and the future working directions for further enhancing the properties of new nanostructured electrodes are discussed., This work was supported by Ministerio de Ciencia, Innovación y Universidades through the RTI2018-093735-B-I00 and UMA18-FEDERJA-033 research projects (Spain). L. dos Santos-Gómez and J. Zamudio-García thanks the Ministerio de Ciencia, Innovación y Universidades for the Juan de la Cierva Formación (FJC2018-036746-I) and FPU (FPU17/02621) grants, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modification of the microstructure and transport properties of La2CuO4−δ electrodes via halogenation routes

  • Santos-Gómez, Lucía dos
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
This article belongs to the Special Issue Solid Oxide Fuel Cell Electrode and Electrochemical Performance., Ruddlesden–Popper type electrodes with composition La2CuO4−δ are alternative cathode materials for solid oxide fuel cells (SOFCs); however, the undoped compound exhibits low electrical conductivity for potential applications, which is usually increased by alkaline-earth doping. A promising alternative to alkaline-earth doping is the modification of the anionic framework by halogen doping. In this study, La2CuO4−0.5xAx (A = F, Cl, Br; x = 0–0.3) compounds are prepared by a freeze-drying precursor method, using an anion doping strategy. The composition, structure, morphology and electrical properties are studied to evaluate their potential use in solid oxide fuel cells (SOFCs). The halogen-doped materials show higher electrical conductivity and improved electrocatalytic activity for oxygen reduction reactions when compared to the pristine material, with polarization resistance values 2.5 times lower, i.e., 0.20, 0.11 and 0.08 Ω cm2 for undoped, F- and Cl-doped samples, respectively, at 800 °C. Moreover, halogen doping prevents superficial copper segregation in La2CuO4−δ, making it an attractive strategy for the development of highly efficient electrodes for SOFCs., This work was supported by the Ministerio de Economía, Industria y Competitividad from Spain (RTI2018-093735-B-I00 and PID2019-110249RB-I00) and Junta de Andalucía (UMA18-FEDERJA-033). L.d.S.-G. and J.Z.-G. thank the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Incorporación (IJC2020-044746-I) and his FPU grant (FPU17/02621), respectively., Peer reviewed