Pasar al contenido principal

DESARROLLO DE CATALIZADORES Y SOPORTES PARA PROCESOS DE ALMACENAMIENTO QUIMICO DE ENERGIA NEUTROS EN CO2 BASADOS EN LIQUIDOS ORGANICOS PORTADORES DE HIDROGENO

RTI2018-093871-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low gas consumption fabrication of 3He solid targets for nuclear reactions

  • Fernández-Camacho, A.
  • Hufschmidt, Dirk
  • Colaux, Julien L.
  • Valiente-Dobón, J. J.
  • Godhino, V.
  • Jiménez de Haro, María del Carmen
  • Feria, David
  • Gadea, Andrés
  • Lucas, Stéphane
Nanoporous solids that stabilize trapped gas nanobubbles open newpossibilities to fabricate solid targets for nuclear reactions. A methodology is described based on the magnetron sputtering (MS) technique operated under quasistatic flux conditions to produce such nanocomposites films with 3He contents of up to 16 at.% in an amorphous-silicon matrix. In addition to the characteristic low pressure (3–6 Pa) needed for the gas discharge, the method ensures almost complete reduction of the process gas flow during film fabrication. The method could produce similarmaterials to those obtained under classical dynamic flux conditions forMS. The drastic reduction (N99.5%) of the gas consumption is fundamental for the fabrication of targets with scarce and expensive gases. Si:3He and W:3He targets are presented together with their microstructural (scanning and transmission electron microscopy, SEM and TEM respectively) and compositional (Ion Beam Analysis, IBA) characterization. The 3He content achieved was over 1 × 1018 at/cm2 for film thicknesses between 1.5 and 3 μm for both Si and Wmatrices. First experiments to probe the stability of the targets for nuclear reaction studies in inverse kinematics configurations are presented, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel solid 4He targets for experimental studies on nuclear reactions: 6Li + 4He differential cross-section measurement at incident energy of 5.5 MeV

  • Ferrer, F. J.
  • Fernández-Martínez, Begoña
  • Fernández-García, J. P.
  • Barba, F. G.
  • Fernández, Asunción
  • Galaviz, D.
  • Godinho, Vanda
  • Gómez-Camacho, Joaquín
  • Sánchez-Benítez, A. M.
A specially prepared Si/He thin solid film was investigated as a suitable target for experimental studies on nuclear reactions involving 4He targets. For that purpose, the elastically scattered 4He recoil coming from the reaction 6Li + 4He at incident energy of 5.5 MeV was measured. The differential cross section of 6Li on 4He has been found to be fully consistent with previous measurements in the literature. The prospective advantages of using these solid He targets in experiments at radioactive beam facilities are discussed., This work was supported by the Spanish Ministry of Science, Innovation and Universities and co-financed by EU FEDER funds under the following grants: FPA2016-77689-C2-1-R, RTI2018-098117-B-C21, RTI2018-093871-B-I00, PGC2018-096994-B-C22, PGC2018-096994-B-C21 and US-1261006. CSIC support under grant PIE-201760E002 is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural characterization and thermal stability of He charged amorphous silicon films prepared by magnetron sputtering in helium

  • Fernández, Asunción
  • Sauvage, T.
  • Diallo, B.
  • Hufschmidt, D.
  • Jiménez de Haro, María del Carmen
  • Montes, O.
  • Martínez-Blanes, José M.
  • Caballero-Hernández, J.
  • Godinho, Vanda
  • Ferrer, F. J.
  • Ibrahim, S.
  • Brault, P.
  • Thomann, A. L.
Sputtering of silicon in a Helium magnetron discharge has been reported as a bottom-up procedure to obtain amorphous Si films containing high amounts of gas-filled nanopores. Here we compare the microstructure and composition of Si–He nanocomposite films deposited by magnetron sputtering (MS) with 4He in DC or RF and 3He in RF operation modes. Electron microscopy (SEM and TEM), X-ray diffraction (XRD) and ion beam analysis (IBA) have been used to analyze the films and to investigate the in-situ and ex-situ thermal evolution. Depending on deposition conditions different in depth compositions, nanopore size and shape distributions, porosity and He content could be obtained. The presence of impurities (i.e. oxygen) has shown to promote He diffusivity reducing He accumulation. The start temperature of He-release varied in the range 473–723 K without films crystallization. Films grown in RF mode reached contents of 32 and 29 at% of 4He and 3He and were respectively stable up to 573 and 723 K both in vacuum and under inert gas flow. In-situ p-EBS (proton Elastic Back Scattering) allowed monitoring the He release accompanied by blistering/delamination effects visualized by SEM. These results show the potentiality of annealing to hold nano-porous structures after liberation of trapped gas., This work was supported by the Spanish and Junta de Andalucía grants no. RTI2018-093871-BI00, P20-00239 and PID2021-124439NB-I00 (all co-financed by EU FEDER) and the CSIC grant 202160E029., This work was also supported by the region of «Centre Val de Loire» and the European Regional Development Funds (FEDER)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructure and activity of Pd catalysts prepared on commercial carbon support for the liquid phase decomposition of formic acid

  • Arzac, G.M.
  • Montes, O.
  • Fernández, Asunción
In this work, a series of Pd catalysts supported on commercially available activated carbon (Norit ®) were prepared by employing different metal precursors (Pd(NO3)2 and Na2PdCl4) by the impregnation-reduction method at different pH. Catalysts were tested for the liquid phase decomposition of formic acid to generate hydrogen. The best results, in terms of small particle size and high catalytic activity were achieved for the Pd/C sample prepared by using Pd(NO3)2 salt impregnated at pH = 2.5, and reduced with sodium borohydride. The particle size of the best Pd/C catalyst is (4.1 ± 1.4) nm with initial TOFs of 2929 and 683 h−1 at 60 and 30 °C respectively and an apparent activation energy of 40 kJ mol−1. Samples prepared by using Na2PdCl4 precursor, consisted of particles with higher size and thus lower activity than the ones prepared with Pd(NO3)2. Regardless the Pd precursor employed, the best results in terms of particle size and activity were achieved at the point of zero charge of the support when the Pd species and the carbon surface were both neutral. The impregnation pH not only determines the particle size, but also the nature of the reducing agent does. The catalytic activity was shown to be size-dependent and it was shown that a mixture of surface Pd0 and PdII oxidation states is beneficial for the activity. When comparing with literature catalysts with similar composition, we found that our best catalyst is competitive enough and that Norit ® support could be promising for future studies on this reaction., This work was supported by the Spanish Ministry of Science and Innovation and Universities under grant no. RTI2018-093871-B-I00 and the Junta de Andalucía under grant no. P20_00239, both co-financed by EU FEDER funds. TEM measurements were performed at the LANE facilities of the ICMS., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation, characterization and activation of Pd catalysts supported on CNx foam for the liquid phase decomposition of formic acid

  • Arzac, G.M.
  • Rojas, T. Cristina
  • Real, C.
  • Fernández, Asunción
In this work, we have prepared a series of Pd catalysts on a CNx support for the liquid phase decomposition of formic acid. The structured CNx support was obtained through thermal pyrolysis of melamine foam and the pyrolysis conditions were optimized to achieve high surface area. The resulting support contains high amount of nitrogen with a contribution of pyridinic component. Several Pd catalysts were prepared and under optimized conditions, we were able to obtain small (2.7 ± 0.9) nm Pd particles by using the oxidized support in powdery form. The activity of the optimized catalyst was studied under different conditions in the fresh and the used form. The fresh catalyst did not show significant activity. However, we found that the catalyst activated after use. Activation was understood in terms of the variation of surface Pd oxidation states under the effect of formic acid/sodium formate solutions. We found that the best activity is achieved under an optimal proportion of Pd0/PdII surface states according to previous reports. Under the best conditions, the activity of the best catalyst (8.6Pd/CN0.3) was as high as 9245 h−1, attributable to the small particle size, the Pd0/PdII ratio, the amount of pyridinic nitrogen, and the testing conditions, which included the preadsorption of sodium formate., This work was supported by the Spanish Ministry of Science and Innovation and Universities under grant no. RTI2018-093871-B-I00 and Junta de Andalucía P20-00239, both co-financed by EU FEDER funds. TEM measurements were performed at the LANE facilities of the ICMS. Many thanks to Almudena Calvo for her help with the drawings in the TOC image., Peer reviewed