Pasar al contenido principal

NUEVOS RETOS EN CEMENTOS ACTIVADOS ALCALINAMENTE:SOSTENIBILIDAD Y EVALUACION AMBIENTAL

RTI2018-097612-B-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential use of ceramic sanitary ware waste as pozzolanic material

  • Reig Cerdá, Lucía
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] This paper evaluated the pozzolanic activity of ceramic sanitary ware (CSW) waste when blended with Portland cement (PC). CSW waste units were broken, crushed and milled to reduce their particle size. These particles were characterized by scanning electron microscopy (SEM-EDX), laser granulometry, X-ray fluorescence (XRF) and X-ray diffraction tests (XRD), and were then used to replace 0¿50 wt.% PC CEM I 42.5R in pastes and mortars. Workability of the fresh mortars was assessed by the flow-table spread test, and the mechanical properties and microstructure (thermogravimetry, SEM-EDX, XRD and Fourier transform infrared spectroscopy tests) were investigated in samples cured at 20 ¿C for up to 365 days. No significant workability variations were observed with increasing waste contents and, although pozzolanic activity of CSW was relatively slow, it improved with the curing time, and mortars prepared with up to 25 wt.% ceramic waste satisfied the requirements established for other pozzolanic materials, such as fly ash., The authors are grateful to the Spanish Ministry of Science, Innovation and Universities for supporting this research through Project ECOSOST RTI-2018-097612-B-C21, and to FEDER funding. They also thank the Institute for Science and Technology of Concrete (ICITECH) and Universitat Jaume I for providing the means to perform this study. Thanks are extended to the Scientific Instrumentation Centre of the Universitat Jaume I and the Electron Microscopy Service of the Universitat Politicnica de Valencia for their help with the microstructural characterization analyses.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hybrid lime-pozzolan-geopolymer systems: microstructural, mechanical and durability studies

  • Villca, Ariel Rey
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
[EN] This work studies the possibility of using geopolymer materials to enhance the mechanical and durability properties of hydrated lime¿pozzolan mixtures, which gave rise to the so-called ¿hybrid systems¿. Two different waste types were used as pozzolan in the lime¿pozzolan system: rice husk ash (RHA) and spent fluid catalytic cracking (FCC). The geopolymer fabricated with FCC was activated with commercial reagents (NaOH and Na2SiO3), and also with alternative sources of silica to obtain a lower carbon footprint in these mixtures. The alternative silica sources were RHA and residual diatomaceous earth (RDE) from the beer industry. The geopolymer mixture substituted the lime¿pozzolan mixture for 30% replacement in weight. The hybrid systems showed better mechanical strengths for the short and medium curing ages in relation to the lime¿pozzolan mixtures. Thermogravimetric analyses were performed to characterise the types of products formed in these mixtures. In the durability studies, hybrid systems better performed in freeze¿thaw cycles and obtained lower capillarity water absorption values., This research forms part of a project supported by MINECO and FEDER funds (ECOSOST RTI2018-097612-B-C21-AR).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Biomass ashes to produce an alternative alkaline activator for alkali-activated cements

  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Font, A.
[EN] In the last decade, herbaceous and agricultural biomass have been used as an alternative energy source. As consequence, large amounts of residual ashes containing potassium (potassium-rich ashes) have been generated. Olive biomass ash (OBA) and almond shell ash (ABA) have been successfully used as alkali source in the alkaline activation of ground granulated blast furnace slag (BFS). This study focuses on the production of new and alternative alkaline activators for BFS systems using nutshell ashes (NBA), mango seed-bark ashes (MBA) and hazelnut shell ashes (HBA). The chemical and mineralogical composition of these ashes were assessed and, the mechanical and microstructural properties of BFS pastes activated with NBA, MBA and HBA were evaluated. The results indicated that all assessed materials are potassium-rich ashes differing mainly on the amount of CaO and P2O5. The compressive strength of BFS pastes yielded about 26 MPa and, according to FESEM/EDS analysis, K2O (in the range 8.03¿24.33%) replaces chemical bounded Ca+2, forming C-(K)-A-S-H gel., We thank the Spanish Government MINECO and FEDER for funding the ECOSOST RTI-2018-097612-B-C21 Project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Almond-shell biomass ash (ABA): a greener alternative to the use of commercial alkaline reagents in alkali-activated cement

  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Font, Alba
  • Bonifacio, Thais
[EN] The use of almond-shell biomass ash (ABA) as an alternative component to the commercial reagents used in the activation of blast furnace slag (BFS) systems is investigated. The presence in its chemical composition of a high content of K2O indicate s that it can alkalinize the medium. 100% waste-based mixtures ABA/BFS were studied by micro- and macrostructural tests. A compressive strength of 44 MPa was achieved by the mortar with 25% ABA addition cured for 7 days at 65 °C. The microstructural analysis showed the formation of slightly different C(K)-A-S-H gels to those formed when using KOH. The use of ABA in BFS mortars is shown as a greener alternative for onstruction materials because the replace- ment of synthetic chemical reagents that produced around a 75¿80% of reduction in the values of kgCO2eq/m3 material, We wish to thank the Spanish Government for project support (MINECO/FEDER-Project RTI2018-09612-B-C21). The authors would like to thank Borges Agricultural & Industrial Nuts for supplying the biomass ash and the Electronic Microscopy Service at the UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reuse of industrial and agricultural waste in the fabrication of geopolymeric binders: mechanical and microstructural behavior

  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Font, Alba
  • Nande, Javier Alejandro
[EN] Resource recovery from waste is one of the most important ways to implement the socalled circular economy, and the use of alkali activated materials can become an alternative for traditional PC-based materials. These types of materials are based on waste resources involving a lower carbon footprint and present similar or high properties and good durability compared to that Portland cement (PC). This research work proposes using new waste generated in different types of industries. Four waste types were employed: fluid catalytic cracking residue (FCC) from the petrochemical industry; ceramic sanitary ware (CSW) from the construction industry; rice husk ash (RHA); diatomaceous waste from beer filtration (DB) (food industry). FCC and CSW were employed as precursor materials, and mixtures of both showed good properties of the obtained alkali activated materials generated with commercial products as activators (NaOH/waterglass). RHA and DB were herein used as an alternative silica source to prepare the alkaline activating solution. Mechanical behavior was studied by the compressive strength development of mortars. The corresponding pastes were characterized by X-ray diffraction, thermogravimetric analysis, and microscopy studies. The results were satisfactory, and demonstrated that employing these alternative activators from waste produces alkali activated materials with good mechanical properties, which were sometimes similar or even better than those obtained with commercial reagents., This research was funded by the Spanish Government and FEDER funds (MINECO/FEDERProject RTI2018-09612-B-C21). This research work forms part of a project supported by MINECO and FEDER funds (ECOSOST RTI2018-097612-B-C21).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Construction System for Single-Family Homes using Load Bearing Straw Bale Walls Quivillungo Community, Bolivar, Ecuador

  • Viera, Paulina
  • Pachala, Jose
  • Rosero, Hernan
  • Caiza, Pablo
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
[EN] This study begins by describing how our team chose an area in the Ecuadorian Andean Region where a prototype single-family home using load bearing straw-bale-walls could be successfully built. The criteria used in this search were based on results from geographic information systems. The next section describes the design and manufacture of a baler machine which is essential to the feasibility of the strawbale home construction procedure. The study then goes on to explain the features of the most important elements of the single-family home structure: fmmdations, straw walls, wall crovVns, roof and structural plaster. The prototype home was built in accordance with existing standards from other cmmtries, taking into account the high seismic hazard of the geographic region and applying the specific capacities of the Quivilllmgo community. The construction was valídated using analytic models that show the existence of relatively low stresses and deformations and highlíght the structural importance of the plaster.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Formulation of alkali-activated slag binder destined for use in developing countries

  • Bella, Nabil
  • Gudiel, Edwin
  • Font-Pérez, Alba
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
[EN] Worldwide cement production is around 4.2 billion tons, and the fabrication of one ton of ordinary Portland cement emits around 900 kg of CO2. Blast furnace slag (BFS) is a byproduct used to produce alkali-activated materials (AAM). BFS production was estimated at about 350 million tons in 2018, and the BFS reuse rate in construction materials of developing countries is low. AAM can reduce CO2 emissions in relation to Portland cement materials: Its use in construction would be a golden opportunity for developing countries in forthcoming decades. The present research aims to formulate AAM destined for future applications in developing countries. Two activators were used: NaOH, Na2CO3, and a mixture of both. The results showed that compressive strengths within the 42¿56 MPa range after 28 curing days were obtained for the Na2CO3-activated mortars. The characterization analysis confirmed the presence of hydrotalcite, carbonated phases, CSH and CASH. The economic study showed that Na2CO3 was the cheapest activator in terms of the relative cost per ton and MPa of manufactured mortars. Finally, the environmental benefits of mortars based on this reagent were evidenced, and, in terms of kgCO2 emissions per ton and MPa, the mortars with Na2CO3 yielded 50% lower values than with NaOH., We would also like to thank the Spanish Government MINECO/FEDER (ECOSOST project RTI-2018-097612-B-C21) for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Lime/pozzolan/geopolymer systems: Performance in pastes and mortars

  • Villca, Ariel R.
  • Font, Alba
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] Use of lime as construction material is limited mainly by low initial strength. These properties can be improved by adding pozzolanic materials, but the evolution of the reaction usually needs older ages than 7 days. Alkali-activated materials, or geopolymers, are good-performance materials that can be produced with residual waste. The combination of traditional and new materials can lead to new uses of lime mortars. This paper studies a lime/pozzolan and geopolymer mixture. The chosen pozzolan is fluid catalytic cracking catalyst residue (FCC), a material employed as a precursor in alkali-activated material. FCC is activated by two activators: a mixture of NaOH and waterglass; a mixture of NaOH and rice husk ash (RHA). The new materials were studied in microstructure and mechanical behaviour terms. The results demonstrated that lime/pozzolan/geopolymer obtained superior compressive strengths after 1 curing day to that obtained for the corresponding lime/pozzolan mortar after 90 days. An improvement in compressive strength of around 145% was achieved for the mortar with 40% geopolymer compared to the mortar with only lime/pozzolan at 28 curing days., This research was supported by Centro de Cooperacion al Desarrollo (CCD) of the Universitat Politecnica de Valencia, ADSIDEO-COOPERACION 2017 Program "Reutilizacion de residuos agricolas e industriales para la fabricacion de conglomerantes sostenibles en paises en desarrollo (AD1708)". The investigation is framed within the ECOSOST (RTI2018-097612-B-C21-AR) project supported by MINECO and FEDER funds. The authors are grateful to the Electron Microscopy Service of the Universitat Politecnica de Valencia, Dacsa Group S.A., Cales Pascual S.L. and BP Oil Espana S.A.U.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Environmental assessment of alkali-activated materials based on agro-industrial waste as alkaline activators through leaching tests

  • Salas, Iván
  • Cifrian, Eva
  • Andrés, Ana
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
[EN] Global circular economy drives the development of sustainable alkali activated materials (AAM) for use as construction material from industrial by-products and wastes. The assessment of the potentially hazardous substances release of these new material combinations into the soil and groundwater over time is essential. In this study, the aim is the environmental assessment of three AAMs based on blast furnace slag (BFS), activated with almond shell biomass ash (ABA) as potassium source and three solid sources of silica from the agricultural industry, rice husk ash (RHA), spent diatomaceous earth (SDE) and bamboo leaf ash (BLA), using European horizontal leaching tests proposed for construction materials, for monolithic form, Dynamic Surface Leaching Test (DSLT) and for granular form, Up-flow Percolation Test and the Compliance leaching test, by simulating different scenarios of their entire life cycle. The leaching results of the AAM showed the effectiveness of the inertization of all the recycled materials studied, which exceeded some inert materials limits, by means of the activation process. Despite the absence of significant differences in the leaching mechanisms of the oxyanions As, Cr, Mo, Sb, Se and V between the three AAMs developed, they presented different long-term leaching behavior depending on their form, monolithic, or granular, and therefore in their different life cycle stages. Therefore, it is concluded that although the incorporation of agro-industrial waste as alternative activators in BFS based AAM according to the Dutch Soil Quality Decree (for unrestricted use of monolithic and granular materials) is an environmentally acceptable option, the design of waste derived AAMs should be assessed by means of a combination of leaching tests that cover their expected life cycle., This work was financially supported by the grants RTI-2018-097612-B-C21 and RTI2018-097612-B-C22, funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe".