Pasar al contenido principal

POLIMEROS NANOCELULARES TRANSPARENTES Y AISLANTES TERMICOS: FABRICACION, CARACTERIZACION Y RELACION PROCESO-ESTRUCTURA-PROPIEDADES.

RTI2018-098749-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE VALLADOLID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Encapsulation of Copper Nanoparticles in Electrospun Nanofibers for Sustainable Removal of Pesticides

  • Quilez-Molina, Ana Isabel
  • Barroso-Solares, Suset
  • Hurtado-García, Violeta
  • Heredia-Guerrero, José Alejandro
  • Rodriguez-Mendez, María Luz
  • Rodríguez-Pérez, Miguel Ángel
  • Pinto, Javier
The excellent catalytic properties of copper nanoparticles (CuNPs) for the degradation of the highly toxic and recalcitrant chlorpyrifos pesticide are widely known. However, CuNPs generally present low stability caused by their high sensitivity to oxidation, which leads to a change of the catalytic response over time. In the current work, the immobilization of CuNPs into a polycaprolactone (PCL) matrix via electrospinning was demonstrated to be a very effective method to retard air and solvent oxidation and to ensure constant catalytic activity in the long term. CuNPs were successfully anchored into PCL electrospun fibers in the form of Cu2O at different concentrations (from 1.25 wt % to 5 wt % with respect to the PCL), with no signs of loss by leaching out. The PCL mats loaded with 2.5 wt % Cu (PCL-2.5Cu) almost halved the initial concentration of pesticide (40 mg/L) after 96 h. This process was performed in two unprompted and continuous steps that consisted of adsorption, followed by degradation. Interestingly, the degradation process was independent of the light conditions (i.e., not photocatalytic), expanding the application environments (e.g., groundwaters). Moreover, the PCL-2.5Cu composite presents high reusability, retaining the high elimination capability for at least five cycles and eliminating a total of 100 mg/L of chlorpyrifos, without exhibiting any sign of morphological damages., Financial assistance from Ministerio de Ciencia e Innovación (Spain) (PID2021-127108OB-I00), MCIN/AEI/10.13039/ 501100011033 and the EU NextGenerationEU/PRTR pro gram (PLEC2021-007705), Ministerio de Ciencia, Innovación y Universidades (MCIU) (Spain), FEDER “Una manera de hacer Europa” (EU) (RTI2018−098749−B-I00 and RTI2018−097367-A-I00), Regional Government of Castilla y León and the EU-FEDER program (CLU-2019-04 and VA202P20), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Studying the Size-Dependence of Graphene Nanoplatelets (GNPs) in the Final Properties of Polyurethane Aerogels: Thermal Insulation and Mechanical Strength

  • Lledó, Jaime
  • Martín de León, Judith
  • Gómez Álvarez-Arenas, Tomás
  • Rodriguez-Pérez, Miguel Angel
  • Merillas, Batriz
21 páginas, 15 figuras, 2 tablas., In the present work, the influence of the addition of graphene nanoplatelets presenting different dimensions on polyurethane–polyisocyanurate aerogel structure and properties has been studied. The obtained aerogels synthesized through a sol–gel method have been fully characterized in terms of density, porosity, specific surface area, mechanical stiffness, thermal conductivity, and speed of sound. Opacified aerogels showing high porosity (>92%) and low densities (78–98 kg/m3) have been produced, and the effect of the size and content of graphene nanoplatelets has been studied. It has been observed that formulations with less than 5 wt.% of graphene nanoplatelets larger than 2 microns can effectively reduce the total thermal conductivity by absorption and scattering of the infrared radiation, reducing the heat transfer by this mechanism. The resulting opacified samples are highly insulating materials, with thermal conductivities less than 18 mW/m·K. Moreover, it has been observed that smaller particles with ca. 200 nm of average length can promote an increase in the elastic modulus, therefore obtaining stiffer aerogels, combined with thermal conductivities lower than 20 mW/m·K. Results have been studied in detail, providing a further understanding of the mechanisms for improving the final properties of these materials, making them more suitable for industrial applications, Financial support from the Science and Innovation Ministry of Spain (RTI2018-098749- B-I00 and PID2021-127108OB-I00, TED2021-130965B-I00, and PDC2022-133391-I00) is gratefully acknowledged. Financial assistance from the Junta of Castille and Leon (VA202P20) is gratefully acknowledged. Activities were funded by the EU NextGeneration and Castille and Leon. Com- plementary plans of research and development with the autonomous regions in actions of R&D. Component 17. Investment 1. (C17. I1), of the recovery, transformation, and resilience plan., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unraveling the structure-properties correlation in thermal insulating and mechanically stiff PLA aerogels

  • Lledó, J.
  • Martín-de León, J.
  • Gómez Álvarez-Arenas, Tomás
  • Rodríguez-Pérez, M.A.
  • Merillas, B.
12 páginas, 12 figuras, 1 tabla, In this study, the relationship between the porous structure of polylactic acid-based (PLA) aerogels and their thermal insulation performance have been studied in detail. Different polymer contents were used for the fabrication of these aerogels leading to a wide range of low densities (36–167 kg/m3), porosities over 86 % and high crystallinity degrees (63–69 %). Their nanofibrillar structures led to high specific surface areas (79–91 m2/g), thin fibers (105–340 nm), and small pores (658–3140 nm). The mechanical performance and thermal insulating behavior have been deeply investigated, analyzing the involved mechanisms. The produced aerogels showed high stiffness with elastic modulus from 0.15 MPa to 12.82 MPa and compressive strengths of up to 540 kPa, significantly higher values than the traditional insulating materials, combined with remarkably low thermal conductivity values between 34.83 and 27.11 mW/m∙K, the lowest value found for PLA of aerogels to date. In addition, thermal conductivity was modeled, and the contributions of the different heat transfer mechanisms were calculated. The obtained results have been related to the different PLA aerogel samples and structural characteristics, obtaining a deep understanding of the relationship between the production process, porous structure, and the final mechanical and thermal insulating performance., Financial support from the Science and Innovation Ministry of Spain (RTI2018-098749-B-I00 and PID2021-127108OB-I00, TED2021-130965B–I00, and PDC2022-133391-I00) is gratefully acknowledged. Financial assistance from the Junta of Castille and Leon (VA202P20) is gratefully acknowledged. Activities funded by the EU NextGeneration and Castille and Leon. Complementary plans of research and development with the autonomous regions in actions of R&D. Component 17. Investment 1. (C17. I1), of the recovery, transformation, and resilience plan. This research is also part of the JDC2023-051979-I (Beatriz Merillas), financed by MCIU/AEI/10.13039/501100011033 and the FSE+., Peer reviewed