Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reaching a near zero radiative heat transfer by the inclusion of modified multiwalled-carbon nanotubes (MWCNTs) in polyurethane-polyisocyanurate aerogels

  • Merillas, Beatriz
  • Gómez Álvarez-Arenas, Tomás
  • Villafañe, Fernando
  • Rodríguez-Pérez, Miguel Angel
11 páginas, 10 figuras, 3 tablas, This article studies the effect of adding different contents of surface-modified multiwalled carbon nanotubes (CNTs) on the structure and final properties of polyisocyanurate-polyurethane aerogels. The produced samples were characterized in terms of density, porosity, shrinkage, textural properties, mechanical behavior, ultrasonic behavior, and thermal conductivity. Low-weight aerogels were obtained with densities between 89 and 95 kg/ m3. The inclusion of homogeneously dispersed carbon nanotubes protected the aerogel structure during super- critical drying decreasing the final shrinkage of these samples and, therefore, increasing their porosity. The porous structure of the aerogels containing CNTs was modified, and slightly larger pores were formed. The structural modifications contribute to decrease the stiffness of the samples while improving their resilience and elasticity. Finally, a significant enhancement on the insulating performance of the aerogels has been found when CNTs were added reaching values as low as 12 mW/mK. These fillers were proved to act as infrared opacifiers by absorbing and scattering the infrared radiation, a relevant contribution in these lightweight materials. In fact, the radiation contribution was strongly reduced when the content of CNTs reached 3 wt%, being this contribution near zero. Thus, this content was considered as the optimum for the final properties-balance in these aerogels., Financial support from the FPU grant FPU17/03299 (Beatriz Merillas) from the Ministerio de Ciencia, Innovación y Universidades is grateful acknowledged. Financial assistance from Ministerio de Ciencia, Innovación y Universidades (MCIU) (Spain) (PID2021-127108OB-I00,TED2021-130965B–I00 and PDC2022-133391-I00), Regional Govern- ment of Castilla y León and the EU-FEDER program (CLU-2019-04 and VA202P20) are gratefully acknowledged. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León), and by the Ministry of Science and Innovation MICIN and the European Union NextGenerationEU/PRTR. (C17. I1)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards the Optimization of Polyurethane Aerogel Properties by Densification: Exploring the Structure– Properties Relationship

  • Merillas, Beatriz
  • García-González, Carlos A.
  • Gómez Álvarez-Arenas, Tomás
  • Rodríguez-Pérez, Miguel Angel
12 páginas, 9 figuras, 4 tablas., The aerogel performance for industrial uses can be tailored using several chemical and physical strategies. The effects of a controlled densification on polyurethane aerogels are herein studied by analyzing their textural, mechanical, sound, optical, and thermal insulating properties. The produced aerogels are uniaxially compressed to different strains (30%–80%) analyzing the consequent changes in the structures and, therefore, final properties. As expected, their mechanical stiffness can be significantly increased by compression (until 55-fold higher elastic modulus for 80%-strain), while the light transmittance does not noticeably worsen until it is compressed more than 60%. Additionally, the modifications produced in the heat transfer contributions are analyzed, obtaining the optimum balance between density increase and pore size reduction. The minimum thermal conductivity (14.5%-reduction) is obtained by compressing the aerogel to 50%-strain, where the increment in the solid conduction is surpassed by the reduction of the radiative and gas contributions. This strategy avoids tedious chemical modifications in the synthesis procedure to control the final structure of the aerogels, leading to the possibility of carefully adapting their structure and properties through a simple method such as densification. Thus, it allows to obtain aerogels for current and on-demand applications, which is one of the main challenges in the field., Financial assistance from Ministerio de Ciencia, Innovación y Universidades (MCIU) (Spain) (PID2021- 127108OB-I00, TED2021-130965B-I00, and PDC2022-133391-I00), Regional Government of Castilla y León and the EU-FEDER program (CLU-2019-04) are gratefully acknowledged. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León), and by the Ministry of Science and Innovation MICIN and the European Union NextGenerationEU/PRTR. (C17. I1). This publication is based upon work from ECO-AERoGELS COST Innovation Grant (ref. IG18125) supported by the European Commission., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Studying the Size-Dependence of Graphene Nanoplatelets (GNPs) in the Final Properties of Polyurethane Aerogels: Thermal Insulation and Mechanical Strength

  • Lledó, Jaime
  • Martín de León, Judith
  • Gómez Álvarez-Arenas, Tomás
  • Rodriguez-Pérez, Miguel Angel
  • Merillas, Batriz
21 páginas, 15 figuras, 2 tablas., In the present work, the influence of the addition of graphene nanoplatelets presenting different dimensions on polyurethane–polyisocyanurate aerogel structure and properties has been studied. The obtained aerogels synthesized through a sol–gel method have been fully characterized in terms of density, porosity, specific surface area, mechanical stiffness, thermal conductivity, and speed of sound. Opacified aerogels showing high porosity (>92%) and low densities (78–98 kg/m3) have been produced, and the effect of the size and content of graphene nanoplatelets has been studied. It has been observed that formulations with less than 5 wt.% of graphene nanoplatelets larger than 2 microns can effectively reduce the total thermal conductivity by absorption and scattering of the infrared radiation, reducing the heat transfer by this mechanism. The resulting opacified samples are highly insulating materials, with thermal conductivities less than 18 mW/m·K. Moreover, it has been observed that smaller particles with ca. 200 nm of average length can promote an increase in the elastic modulus, therefore obtaining stiffer aerogels, combined with thermal conductivities lower than 20 mW/m·K. Results have been studied in detail, providing a further understanding of the mechanisms for improving the final properties of these materials, making them more suitable for industrial applications, Financial support from the Science and Innovation Ministry of Spain (RTI2018-098749- B-I00 and PID2021-127108OB-I00, TED2021-130965B-I00, and PDC2022-133391-I00) is gratefully acknowledged. Financial assistance from the Junta of Castille and Leon (VA202P20) is gratefully acknowledged. Activities were funded by the EU NextGeneration and Castille and Leon. Com- plementary plans of research and development with the autonomous regions in actions of R&D. Component 17. Investment 1. (C17. I1), of the recovery, transformation, and resilience plan., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced thermal insulation performance of silica aerogel composites through infrared opacifier integration for high-temperature applications

  • Merillas, Beatriz
  • Almeida, Cláudio M.R.
  • Gómez Álvarez-Arenas, Tomás
  • Rodríguez-Pérez, Miguel Angel
  • Durães, Luisa
10 páginas, 9 figuras, 1 tabla., The inclusion of different fillers in silica aerogels reinforced by a reticulated polyurethane skeleton, allows for the development of a strategy to obtain composites with superior characteristics. Different fillers (TiO2, GO, SiC) and contents (0.2, 0.5 and 1.0 wt.%) were explored, analyzing their effects on the porous structures, mechanical stiffness and thermal conductivity of the composites. These exhibited low densities, reduced shrinkage, and high specific surface areas of approximately 550 m2/g. The incorporated fillers were homogeneously dispersed, leading to a general decrease in the mean pore size. Despite observing a slight reduction in the elastic modulus with respect to the non-doped composite, the benefits of this strategy are twofold; the composites can withstand strains above 80 % without breaking, significantly improving the mechanical stability when compared to non- reinforced silica aerogels, and while achieving high resilience. Additionally, enhanced thermal insulating per- formance was found for some materials. After analyzing the heat transfer contributions, the optimum particle contents for an improved thermal insulation were identified (1.0 wt.% TiO2 and 0.2 wt.% SiC), leading to an effective reduction of the radiation term and reaching overall reductions of 10 and 6.5 % at 100 ◦C. Therefore, the silica aerogel-based composites herein produced represent a step forward in their usability and versatility for cutting-edge applications., Financial assistance from Ministerio de Ciencia, Innovaci´on y Uni- versidades (MCIU) (Spain) (PID2021-127108OB-I00, TED2021- 130965B-I00, PID2020-120010RB-I0 and PDC2022-133,391-I00), Regional Government of Castilla y Le´on and the EU-FEDER program (CLU-2019-04 and VA202P20) are gratefully acknowledged. This work was supported by the Regional Government of Castilla y Le´on (Junta de Castilla y Le´on), and by the Ministry of Science and Innovation MICIN and the European Union NextGenerationEU / PRTR. (C17. I1). CERES research unit was supported by national funds from FCT - Fundaç˜ao para a Ciˆencia e a Tecnologia, I.P., and when appropriate co-funded by the European Regional Development Fund (ERDF), under the scope of projects 10.54499/UIDB/00102/2020 and 10.54499/UIDP/00102/ 2020., Peer reviewed