Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reaching a near zero radiative heat transfer by the inclusion of modified multiwalled-carbon nanotubes (MWCNTs) in polyurethane-polyisocyanurate aerogels

  • Merillas, Beatriz
  • Gómez Álvarez-Arenas, Tomás
  • Villafañe, Fernando
  • Rodríguez-Pérez, Miguel Angel
11 páginas, 10 figuras, 3 tablas, This article studies the effect of adding different contents of surface-modified multiwalled carbon nanotubes (CNTs) on the structure and final properties of polyisocyanurate-polyurethane aerogels. The produced samples were characterized in terms of density, porosity, shrinkage, textural properties, mechanical behavior, ultrasonic behavior, and thermal conductivity. Low-weight aerogels were obtained with densities between 89 and 95 kg/ m3. The inclusion of homogeneously dispersed carbon nanotubes protected the aerogel structure during super- critical drying decreasing the final shrinkage of these samples and, therefore, increasing their porosity. The porous structure of the aerogels containing CNTs was modified, and slightly larger pores were formed. The structural modifications contribute to decrease the stiffness of the samples while improving their resilience and elasticity. Finally, a significant enhancement on the insulating performance of the aerogels has been found when CNTs were added reaching values as low as 12 mW/mK. These fillers were proved to act as infrared opacifiers by absorbing and scattering the infrared radiation, a relevant contribution in these lightweight materials. In fact, the radiation contribution was strongly reduced when the content of CNTs reached 3 wt%, being this contribution near zero. Thus, this content was considered as the optimum for the final properties-balance in these aerogels., Financial support from the FPU grant FPU17/03299 (Beatriz Merillas) from the Ministerio de Ciencia, Innovación y Universidades is grateful acknowledged. Financial assistance from Ministerio de Ciencia, Innovación y Universidades (MCIU) (Spain) (PID2021-127108OB-I00,TED2021-130965B–I00 and PDC2022-133391-I00), Regional Govern- ment of Castilla y León and the EU-FEDER program (CLU-2019-04 and VA202P20) are gratefully acknowledged. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León), and by the Ministry of Science and Innovation MICIN and the European Union NextGenerationEU/PRTR. (C17. I1)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards the Optimization of Polyurethane Aerogel Properties by Densification: Exploring the Structure– Properties Relationship

  • Merillas, Beatriz
  • García-González, Carlos A.
  • Gómez Álvarez-Arenas, Tomás
  • Rodríguez-Pérez, Miguel Angel
12 páginas, 9 figuras, 4 tablas., The aerogel performance for industrial uses can be tailored using several chemical and physical strategies. The effects of a controlled densification on polyurethane aerogels are herein studied by analyzing their textural, mechanical, sound, optical, and thermal insulating properties. The produced aerogels are uniaxially compressed to different strains (30%–80%) analyzing the consequent changes in the structures and, therefore, final properties. As expected, their mechanical stiffness can be significantly increased by compression (until 55-fold higher elastic modulus for 80%-strain), while the light transmittance does not noticeably worsen until it is compressed more than 60%. Additionally, the modifications produced in the heat transfer contributions are analyzed, obtaining the optimum balance between density increase and pore size reduction. The minimum thermal conductivity (14.5%-reduction) is obtained by compressing the aerogel to 50%-strain, where the increment in the solid conduction is surpassed by the reduction of the radiative and gas contributions. This strategy avoids tedious chemical modifications in the synthesis procedure to control the final structure of the aerogels, leading to the possibility of carefully adapting their structure and properties through a simple method such as densification. Thus, it allows to obtain aerogels for current and on-demand applications, which is one of the main challenges in the field., Financial assistance from Ministerio de Ciencia, Innovación y Universidades (MCIU) (Spain) (PID2021- 127108OB-I00, TED2021-130965B-I00, and PDC2022-133391-I00), Regional Government of Castilla y León and the EU-FEDER program (CLU-2019-04) are gratefully acknowledged. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León), and by the Ministry of Science and Innovation MICIN and the European Union NextGenerationEU/PRTR. (C17. I1). This publication is based upon work from ECO-AERoGELS COST Innovation Grant (ref. IG18125) supported by the European Commission., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unraveling the structure-properties correlation in thermal insulating and mechanically stiff PLA aerogels

  • Lledó, J.
  • Martín-de León, J.
  • Gómez Álvarez-Arenas, Tomás
  • Rodríguez-Pérez, M.A.
  • Merillas, B.
12 páginas, 12 figuras, 1 tabla, In this study, the relationship between the porous structure of polylactic acid-based (PLA) aerogels and their thermal insulation performance have been studied in detail. Different polymer contents were used for the fabrication of these aerogels leading to a wide range of low densities (36–167 kg/m3), porosities over 86 % and high crystallinity degrees (63–69 %). Their nanofibrillar structures led to high specific surface areas (79–91 m2/g), thin fibers (105–340 nm), and small pores (658–3140 nm). The mechanical performance and thermal insulating behavior have been deeply investigated, analyzing the involved mechanisms. The produced aerogels showed high stiffness with elastic modulus from 0.15 MPa to 12.82 MPa and compressive strengths of up to 540 kPa, significantly higher values than the traditional insulating materials, combined with remarkably low thermal conductivity values between 34.83 and 27.11 mW/m∙K, the lowest value found for PLA of aerogels to date. In addition, thermal conductivity was modeled, and the contributions of the different heat transfer mechanisms were calculated. The obtained results have been related to the different PLA aerogel samples and structural characteristics, obtaining a deep understanding of the relationship between the production process, porous structure, and the final mechanical and thermal insulating performance., Financial support from the Science and Innovation Ministry of Spain (RTI2018-098749-B-I00 and PID2021-127108OB-I00, TED2021-130965B–I00, and PDC2022-133391-I00) is gratefully acknowledged. Financial assistance from the Junta of Castille and Leon (VA202P20) is gratefully acknowledged. Activities funded by the EU NextGeneration and Castille and Leon. Complementary plans of research and development with the autonomous regions in actions of R&D. Component 17. Investment 1. (C17. I1), of the recovery, transformation, and resilience plan. This research is also part of the JDC2023-051979-I (Beatriz Merillas), financed by MCIU/AEI/10.13039/501100011033 and the FSE+., Peer reviewed