Pasar al contenido principal

Novel Contactless Magneto-Mechanical Devices for Precision Miniaturized Robotic Manipulators (MEMS) and Energy Harvesting

RYC-2017-23684

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Ramón y Cajal
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Ultra-Low Power Consumption Electromagnetic Actuator Based on Potential Magnetic Energy Harnessing: Principle of Operation and Experimental Validation

  • Albertos Cabañas, Miguel
  • Valiente Blanco, Ignacio|||0000-0001-5068-7910
  • Manzano Narro, Óscar
  • López Pascual, Diego|||0000-0002-2485-2297
  • Sánchez Prieto, Sebastián|||0000-0002-6729-7932
This paper presents a novel rotary electromagnetic actuator designed for high-speed and high-precision positioning with ultra-low power consumption, intended for industrial and scientific applications such as rotary index tables, pick and place robots, or optical systems, amongothers. The actuator is based on harnessing electromagnetic potential energy and its transformation into kinetic energy to enable accurate and rapid changes between different equilibrium positions of the device. A prototype with an outer diameter of 86 mm and a thickness of 25 mm and a mass of about 0.57 kg has been manufactured and tested. It presents eight equilibrium positions evenly separated to 45 degrees, reachable in just 48 ms with a positioning accuracy of 20 arcmin. Experimental results demonstrate that the device generates a torque of 590 mNm, maximum angular speed and acceleration up to 663 rpm and 14,500 rad/s2, respectively, with an input current of ±500 mA and a maximum power consumption of just 6.3 W. This value of power consumption represents a power saving up to 80%whencompared to a conventional electromagnetic actuator that reproduces the same motion profile. An energy saving up to 38% is calculated for a change between two adjacent equilibrium positions. This innovative technology provides a new tool for precise positioning in highly dynamic applications with unprecedented energy and power savings., Ministerio de Ciencia, Innovación y Universidades
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Improving the efficiency of solar photovoltaics by means of geothermal cooling: a year-long test campaign

  • López Pascual, Diego|||0000-0002-2485-2297
  • Valiente Blanco, Ignacio|||0000-0001-5068-7910
  • Fernández Muñoz, Miguel|||0000-0001-8872-7834
  • Díez Jiménez, Efrén|||0000-0002-3689-841X
Heating up of photovoltaic modules during operation results in a significant power output reduction. This effect is especially relevant in regions with the highest photovoltaic potential, where irradiance and ambient temperature are particularly high. In this paper, a novel low enthalpy geothermal cooling system that improves the efficiency of a commercial solar module is described and experimentally validated. Two heat exchangers, one attached to the backside of the module, and another introduced inside a 15 m deep borehole, are connected in a closed circuit. A water-based coolant is pumped through the system, evacuating the excess heat from the module, and dissipating it underground in a clean and efficient manner, without additional water consumption after filling the system. The performance of the cooling system was experimentally tested by implementing it, for the first time, in a single-axis solar tracking isolated photovoltaic facility. Extensive tests were carried out in Spain, between September 2021 and August 2022 under a wide variety of environmental conditions. The efficiency improvement system has demonstrated its technical feasibility over a one-year period, showing a peak net efficiency improvement up to 13.4 %. Moreover, a positive net efficiency improvement has been demonstrated all year long, even during the winter months., Ministerio de Ciencia e Innovación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Theoretical modelling and optimization of a geothermal cooling system for solar photovoltaics

  • López Pascual, Diego|||0000-0002-2485-2297
  • Valiente Blanco, Ignacio|||0000-0001-5068-7910
  • Fernández Muñoz, Miguel|||0000-0001-8872-7834
  • Díez Jiménez, Efrén|||0000-0002-3689-841X
Solar cells lose efficiency as the operating temperature increases under normal operating conditions, resulting in a very significant power output reduction. This issue is most relevant in areas with the highest photovoltaic energy harvesting potential, where irradiance and ambient temperature are particularly high. A novel cooling system for commercial photovoltaic modules based on low-enthalpy geothermal cooling is proposed in this paper. Excess heat is evacuated from the solar module in a clean and efficient manner by a single-phase and close-loop cooling circuit that uses the underground as a natural heatsink. In addition, a thermoelectrical theoretical model is presented, that allows the optimization of the flowrate and the maximization of the extra power generation of the cooled module. A prototype was manufactured and tested in outdoor conditions in September 2021 in Spain. Test results are in good agreement with the theoretical model, which has been used for prediction of the performance of the system for a typical meteorological year in the region. A peak efficiency improvement of 10.7% is calculated for the month of July, with an optimal flowrate of 1.8 l/min per square meter of solar module. A yearly weighted average power gain of up to 4.9% is also calculated., Ministerio de Ciencia e Innovación, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Experimental study of micromilling process and deburring electropolishing process on FeCo-based soft magnetic alloys

  • Villalba Alumbreros, Gabriel
  • López Cámara, Enrique
  • Martínez Gómez, Javier|||0000-0001-8807-7595
  • Cóbreces Álvarez, Santiago|||0000-0002-3308-4613
  • Valiente Blanco, Ignacio|||0000-0001-5068-7910
  • Díez Jiménez, Efrén|||0000-0002-3689-841X
FeCo-based soft magnetic alloys are commonly used in macroscale devices to improve its electromagnetic performance, whereas they have been barely used in the microscale. Current FeCo alloy micromanufacturing processes present some difficulties like low structural strength, oxidation at high temperature processes, stoichiometry mismatches in deposition processes and tough workability. In this work, a microcutting of FeCo-2 V-based soft magnetic alloys process is presented and described as an alternative method to obtain microparts with high magnetic properties and good geometrical finish. The results of the machining process are analysed by varying the machining parameters such as depth of cut, tool diameter, rotation speed and feed speed on simple machining operations. The study has been done for 50-μm-diameter endmill and 250-μm-diameter endmill tools. It concludes that the roughness is minimized when machining parameter combination is 0.24 mm/min of feed rate and 8 μm of depth of cut size for a 250-μm-diameter tool, while for a 50-μm-diameter tool, the selected feed rate is 0.24 mm/min, for a depth of cut between 2 and 4 μm. An automated precision 3-axis CNC station is used. Shapes needed for actuators such as angular slots, disks, or slender square geometries are shown in this work with excellent magnetic and mechanical properties. Additionally, a complementary electropolishing process is described. This process helps to eliminate burr in edges and residuals of the milling operation. This study demonstrates that micromilling can be a good alternative for microfabrication of FeCo-2 V components, suitable for precision microassemblies on MEMS., European Commission, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Experimental characterization of a geothermal cooling system for enhancement of the efficiency of solar photovoltaic panels

  • López Pascual, Diego|||0000-0002-2485-2297
  • Valiente Blanco, Ignacio|||0000-0001-5068-7910
  • Manzano Narro, Óscar
  • Fernández Muñoz, Miguel|||0000-0001-8872-7834
  • Díez Jiménez, Efrén|||0000-0002-3689-841X
2022 The 5th International Conference on Renewable Energy and Environment Engineering (REEE 2022), 24–26 August, 2022, Brest, France., The efficiency of solar photovoltaic panels reduces when their temperature increases during normal operation conditions, resulting in a very significant power output reduction. This phenomenon is especially relevant in regions with high photovoltaic potential where irradiance and ambient temperature are particularly high as well. To overcome this issue, a compact cooling system for commercial photovoltaic panels based on low-enthalpy geothermal cooling is proposed. Overheating is evacuated from the solar panel by a single-phase close-loop cooling system that gets benefit of a natural underground heat sink, which is at a constant and low temperature. A prototype, integrating a single axis sun tracking mechanism, has been assembled and tested in outdoor conditions in June 2022 in Alcalá de Henares, Madrid, Spain. As it has been experimentally demonstrated, with a coolant flowrate of 1.8 l/min per square meter of panel surface, the cooling system reduces the temperature of the cooled panel up to 20 C, which resulted in a real improvement of the panel’s efficiency up to 13.8%. Finally, a sensitivity analysis of the net power gain and the net extra energy produced by the cooled panel is presented., Ministerio de Ciencia e Innovación, Universidad de Alcalá