Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nitrogen functionalities in mesoporous carbons and their impact on the sulfur infiltration efficiency and in the electrochemical performance of Li–S cells

  • Laverde, Jennifer
  • Rosero-Navarro, Nataly Carolina
  • Buitrago-Sierra, Robinson
  • López, Diana
[EN] The cyclability of Li–S batteries depends strongly on electrochemical cell stability, which is affected by the dilution of lithium polysulfides in the electrolyte. One of the proposed solutions is the use of porous carbonaceous materials in the cathode that trap lithium polysulfide species and prevent them from reaching the electrolyte. This is possible by using dopant heteroatoms in the carbon framework such as nitrogen to generate anchoring sites reducing the shuttle effect. To understand how the sulfur infiltration process in carbonaceous materials is affected by the inclusion of nitrogen in the carbon structure and its effect on the electrochemical performance of Li–S batteries, in this study N-doped mesoporous carbons were prepared by varying the carbonization temperature, focusing on the structural and compositional variations. At the highest carbonization temperature (850 °C), a carbonaceous material with the lowest nitrogen content was obtained mainly prevailing the N-quaternary functionality over N-pyrrolic and N-pyridinic. The sulfur infiltration into the pores of the material was improved due to the moderate polarity obtained under the carbonization temperature used (850 °C). Given the distribution of nitrogen functionalities, it was possible to obtain a material with a high degree of graphitization reflected in the electrochemical performance where after 100 cycles a discharge capacity of 422.3 mA h g was reached with a Coulombic efficiency of 99%., Universidad de Antioquia UdeA and the project 2022-0735 funded by Minciencias. Robison Buitrago-Sierra thanks to the project PE22201. Partial financial support of this work through Ramon y Cajal Grant No. RYC2020–029909-I of The Spanish State Research Agency to N.C. Rosero-Navarro., Supplementary data to this article can be found online at https://doi.org/10.1016/j.ssi.2023.116303., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A Stable Rechargeable Aqueous Zn-Oxygen Battery with Mn-based Bifunctional Electrocatalysts

  • González-Morales, Jorge
  • Aparicio, Mario
  • Rosero-Navarro, Nataly Carolina
  • Mosa Ruiz, Jadra
One promising alternative for more efficient and sustainable energy storage systems is the utilization of Zn-O2 batteries, which boast higher energy densities compared with conventional Li-ion batteries. Despite their potential, Zn-O2 batteries are not yet widely used in industrial applications due to their low cyclability and dependence on Platinum Group Metals (PGM). To address these issues, in this research, the development of bifunctional electrocatalysts based on Mn is proposed. While widely documented electrocatalysts like MnO2 demonstrate excellent catalytic behavior for the Oxygen Reduction Reaction (ORR), they lack Oxygen Evolution Reaction (OER) capacity. In this study, bifunctional electrocatalysts are obtained through the incorporation of N (nitrogen) and C (carbon) by using urea and surfactants. The chemical, microstructural, and electrochemical properties of these electrocatalysts were thoroughly evaluated. The results reveal that these materials exhibit a promising catalytic capacity for both ORR and OER and a stable charge-discharge cycling performance reaching a discharge capacity of 800 mAh g-1 © 2024 The Authors. Published by American Chemical Society, This project PCI2018-092982 Novel carbon-f ree cathode materials for metal−air rechargeable batteries (CarFree) has been funded by EIG-Concert-Japan, Reference (Ministry of Science, Innovation and Universities, Proyectos de I+D+I “Programación Conjunta Internacional” 2018): PCI2018- 092982. J.G.-M. thanks to Comunidad de Madrid for predoctoral contract ( CAM19_PRE_ICGARJUV_002). N.C.R.-N. thanks to Ramon y Cajal Project RyC-RYC2020- 029909-I., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Temperature during Open Vessel Sintering on Li6PS5Cl Solid-State Electrolyte Powders for Use in Cathode Composite Electrodes

  • Warren, Zachary
  • Seghers, Miguel
  • Boissière, Pierre
  • Aparicio, Mario
  • Rosero-Navarro, Nataly Carolina
The sulfide solid electrolyte Li6PS5Cl has beenshown to be an ideal candidate for use in composite electrodes forall solid-state lithium-ion batteries due to its high ionicconductivity, low activation energy, and rapid processability insolvents (solution-based processing). Many reports for solution-based processing of Li6PS5Cl required the electrolyte to bedensified or sealed inside of a closed-quartz vessel prior to a finalhigh-temperature sintering step. This pre-sintering step is useful forunderstanding the full electrochemical properties of the electrolytebut provides little information about usable electrolyte powders forcommercialization. Modern applications of solid electrolytepowders require a feedstock of powdered electrolyte, which canbe processed by tape-casting, screen-printing, aerosol deposition,electrophoretic deposition, and hot powder rolling. The lack of information regarding the sintering of Li6PS5Cl powders for bulkprocessing warrants an investigation into open vessel sintering of solely the Li6PS5Cl electrolyte powders, which can later be used incomposite electrodes. This research uses a solution-based processing technique to synthesize Li6PS5Cl prior to sintering in open-topborosilicate glass containers. Here we show the effects that sintering temperatures have on Li6PS5Cl electrolyte powders duringopen-vessel sintering using X-ray diffraction, scanning electron microscopy, and Raman spectroscopy for morphological analysis.Electrochemical characterization was performed using AC electrical impedance spectroscopy, cyclic voltammetry, andchronoamperometry. Lastly, a full solid-state electrochemical cell was constructed with a cathode composite electrode madefrom the Li6PS5Cl to illustrate the functionality of the electrolyte., This research work is part of PIE project “Innovative andDesigned (Electro)-Chemistry, All-in-One for Lithium SulfideSolid Electrolytes” (IDEAL-Li), reference 20226AT009supported by The Spanish National Research Council(CSIC). Financial support of this work through Ramon yCajal Grant No. RYC2020−029909-I of The Spanish StateResearch Agency to N.C. Rosero-Navarro. Partially supportedby Microxide Project of The Spanish State Research Agency,TED2021−130911B−I00, funded by MCIN/AEI/10.13039/501100011033, and by the European Union “NextGener-ationEU”/PRT. Pierre Boissiè re thanks Erasmus+ Programmefor supporting educational training internship, agreement174191-2023, Peer reviewed