Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A computational investigation on the influence of the use of elliptical orifices on the inner nozzle flow and cavitation development in diesel injector nozzles

  • Molina, Santiago|||0000-0001-7879-2421
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Jaramillo, D.
In this paper a computational study was carried out in order to investigate the influence of the use of elliptical orifices on the inner nozzle flow and cavitation development. With this aim, a large number of injection conditions have been simulated and analysed for 5 different nozzles: four nozzles with different elliptical orifices and one standard nozzle with circular orifices. The four elliptical nozzles differ from each other in the orientation of the major axis (vertical or horizontal) and in the eccentricity value, but keeping the same outlet section in all cases. The comparison has been made in terms of mass flow, momentum flux and other important non-dimensional parameters which help to describe the behaviour of the inner nozzle flow: discharge coefficient (C-d), area coefficient (C-a) and velocity coefficient (C-v). The simulations have been done with a code able to simulate the flow under either cavitating or non-cavitating conditions. This code has been previously validated using experimental measurements over the standard nozzle with circular orifices. The main results of the investigation have shown how the different geometries modify the critical cavitation conditions as well as the discharge coefficient and the effective velocity. In particular, elliptical geometries with vertically oriented major axis are less prone to cavitate and have a lower discharge coefficient, whereas elliptical geometries with horizontally oriented major axis are more prone to cavitate and show a higher discharge coefficient. (C) 2013 Elsevier Ltd. All rights reserved., This work was partly sponsored by "Vicerrectorado de Investigacion, Desarrollo e Innovacion" of the "Universitat Politecnica de Valencia" in the frame of the project "Estudio de la influencia del uso de combustibles alternativos sobre el proceso de inyeccion mediante GRID computing (FUELGRID)", Reference SP20120396 and by "Ministerio de Economia y Competitividad" in the frame of the project "Comprension de la influencia de combustibles no convencionales en el proceso de inyeccion y combustion tipo diesel", reference TRA2012-36932. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the influence of the needle eccentricity on the internal flow in diesel injector nozzles by computational fluid dynamics calculations

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Martínez López, Jorge Eugenio
  • Romero, José-Vicente|||0000-0003-3366-6557
  • Roselló, María-Dolores|||0000-0002-5724-7683
In the present paper, a computational study has been performed in order to clarify the effects of the needle eccentricity in a real multihole microsac nozzle. This nozzle has been simulated at typical operating conditions of a diesel engine, paying special attention to the internal flow development and cavitation appearance within the discharge orifices. For that purpose, a multiphase flowsolver based on a homogeneous equilibrium model with a barotropic equation of state has been used, introducing the turbulence effects by Reynolds-averaged Navier Stokes methods with a re-normalization group k-eps model. The results obtained from this investigation have demonstrated the huge influence of the needle position on the flow characteristics, showing important hole to hole differences., This work was partly sponsored by 'Vicerrectorado de Investigacion, Desarrollo e Innovacion' of the 'Universitat Politecnica de Valencia' in the frame of the project 'Estudio de la influencia del uso de combustibles alternativos sobre el proceso de inyeccion mediante GRID computing (FUELGRID)', and by 'Ministerio de Ciencia e Innovacion' in the frame of the project 'Estudio teorico-experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), reference TRA2011-26293. This support is gratefully acknowledged by the authors.