Pasar al contenido principal

ESTUDIO TEORICO-EXPERIMENTAL SOBRE LA INFLUENCIA DEL TIPO DE COMBUSTIBLE EN LOS PROCESOS DE ATOMIZACION Y EVAPORACION DEL CHORRO DIESEL

TRA2011-26293

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Combination of Visualization Techniques for the Analysis of Evaporating Diesel Sprays

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Gil, A.|||0000-0001-7192-6992
[EN] Evaporating diesel sprays from three different multi-hole nozzles have been studied by means of three different and complementary techniques: Mie scattering, double-pass schlieren, and CH radical chemiluminescence. These three kinds of measurements provided valuable information that has allowed us to shed light on the influence of nozzle geometry on the air-fuel mixing and evaporation processes. For this purpose, three six-hole sac nozzles, with different orifice degrees of conicity have been used. These nozzles had been geometrically and hydraulically characterized in a previous publication, where important non-dimensional coefficients describing the nature of the flow have been evaluated. Injection at different pressure conditions has been carried out in an inert environment of gas to study the mixture process, avoiding window fouling by soot deposition from combustion. Studies have been carried out for three different injection pressures and four different gas densities during spray injection, representative of real engine conditions, with changing temperature and pressure in the discharge camera. Liquid-phase penetration and stabilized liquid length for all nozzles and pressure conditions have been determined with the Mie scattering technique. The cylindrical nozzle provided the highest value of the liquid length at a low injection pressure (30 MPa), because of its higher diameter and the absence of cavitation. When the two conical nozzles are compared, no clear differences have been shown between them. Because with this Mie scattering, it is not possible to follow the vapor behavior and considering constraints associated with the geometrical configuration of diesel sprays generated by the multi-hole nozzles, a double-pass schlieren technique has been used for this purpose. The combination of Mie scattering and schlieren allowed for the liquid and vapor phases to be analyzed in terms of penetration. As far as the CH radicals are concerned, these radicals are supposed to appear beyond the position of the stabilized liquid length; however, results show how first CH radical intensity is detected before liquid-phase penetration reaches the stabilized value. When CH radical apparition delays from the start of the injection between all of the nozzles and for all injection conditions are compared, in overall terms, conical nozzles present less delay than cylindrical nozzles. This means that the air-fuel mixing process is more effective in the case of conical nozzles. Thus, the analysis of all of the results made it possible to link the nozzle geometry, fuel-air mixture, spray evaporation, and incipient combustion. © 2012 American Chemical Society., This work was partly sponsored by "Vicerrectorado de Investigacion, Desarrollo e Innovacion" of the "Universitat Politecnica de Valencia" in the frame of Project "Estudio del Flujo en Toberas de Inyeccion Diesel Mediante Tecnicas LES (LESFLOWGRID)", Reference 2837, and "Ministerio de Ciencia e Innovacion" in the frame of Project "Estudio Teorico-Experimental sobre la Influencia del Tipo de Combustible en los Procesos de Atomizacion y Evaporacion del Chorro Diesel (PROFUEL)", Reference TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of natural and tracer fluorescent emission methods for droplet size measurements in a diesel spray

  • Pastor, José V.|||0000-0003-4113-4681
  • Payri, Raul|||0000-0001-7428-5510
  • Salavert Fernandez, Javier
  • Manin, J.
Spray sizing that records fluorescent emission and scattered light has been widely applied to spray diagnostics over the last two decades. Different experimental strategies have been developed, but comparing the different solutions offered has remained of interest to experimentalists. In this work, a comparison of two fluorescence strategies for measuring droplet size in the liquid phase of a last-generation DI diesel spray is conducted. The natural fluorescent emission of a commercial diesel fuel and the fluorescence emitted by a tracer (Rhodamine B) are compared using theoretical and experimental approaches. The LIF/Mie ratio commonly called Planar Droplet Sizing (PDS) technique is applied in two different ways to elucidate the possible advantages of using a fluorescent dopant. The sprays were injected under non-evaporative conditions into a constant pressure vessel that simulates densities present at the moment of injection in currently used passenger car diesel engines. Characterization of the signal properties was performed by measuring the absorption coefficient, fluorescence emission spectrum, quantum yield and lifetime of both configurations. The scattered light and fluorescence intensities were calculated to verify the dependencies of the droplet surface and volume. When applying the two techniques to quantify droplet size in dense diesel sprays, the results show that signal weakness and lack of control over the properties of natural fluorescence produce distortion in the shape of the spray and cause measurements to be unreliable. © 2012 The Korean Society of Automotive Engineers and Springer-Verlag Berlin Heidelberg., This research has been funded in the frame of the project PROFUEL reference TRA2011-26293 from Ministerio de Ciencia e Innovacion. The injectors are part of the ECN international project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of diesel spray atomization by means of a near-nozzle field visualization technique

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • De La Morena, Joaquín|||0000-0003-0208-508X
[EN] In this paper, a high-resolution visualization technique has been used in order to characterize Diesel spray structure in the near-nozzle field. For this purpose, three conical nozzles with different diameters have been used to relate nozzle geometry and spray behavior in non-cavitating conditions. As a first step, geometrical and hydraulic characterization of the nozzles has been performed. The analysis of the images obtained has shown that spray aperture varied significantly during the first millimeters of the spray, until reaching to the stabilized value of spray cone angle, which is the one usually characterized by other visualization techniques. Furthermore, the structure of the liquid-gas interface presented an oscillatory behavior, which is related to primary atomization process. These oscillations have been quantified and statistically correlated with nozzle geometry and operating conditions by means of three different non-dimensional numbers: Reynolds number, air/fuel density ratio, and Ohnesorge number. © 2011 by Begell House, Inc., This research was sponsored by Vicerrectorado de Investigacion, Desarrollo e Innovacion of the Universitat Politecnica de Valencia, under the Project ` Estudio numerico del flujo en toberas de inyeccion diesel con aproximacion LES y mediante grid computing (LESFLOWGRID), Reference 2837, and by Ministerio de Ciencia e Innovacion, under the Project Estudio teorico experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), Reference No. TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the influence of the needle eccentricity on the internal flow in diesel injector nozzles by computational fluid dynamics calculations

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Martínez López, Jorge Eugenio
  • Romero, José-Vicente|||0000-0003-3366-6557
  • Roselló, María-Dolores|||0000-0002-5724-7683
In the present paper, a computational study has been performed in order to clarify the effects of the needle eccentricity in a real multihole microsac nozzle. This nozzle has been simulated at typical operating conditions of a diesel engine, paying special attention to the internal flow development and cavitation appearance within the discharge orifices. For that purpose, a multiphase flowsolver based on a homogeneous equilibrium model with a barotropic equation of state has been used, introducing the turbulence effects by Reynolds-averaged Navier Stokes methods with a re-normalization group k-eps model. The results obtained from this investigation have demonstrated the huge influence of the needle position on the flow characteristics, showing important hole to hole differences., This work was partly sponsored by 'Vicerrectorado de Investigacion, Desarrollo e Innovacion' of the 'Universitat Politecnica de Valencia' in the frame of the project 'Estudio de la influencia del uso de combustibles alternativos sobre el proceso de inyeccion mediante GRID computing (FUELGRID)', and by 'Ministerio de Ciencia e Innovacion' in the frame of the project 'Estudio teorico-experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), reference TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Consequences of using biodiesel on the injection and air-fuel mixing processes in diesel engines

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
  • Salavert Fernández, José Miguel|||0000-0001-8789-5916
  • De La Morena, Joaquín|||0000-0003-0208-508X
A study of the injection process and spray behaviour was made for three different fuels. In particular, blends of rapeseed methyl ester and standard diesel fuel with 5% and 30% biodiesel were used for the current study, as well as pure rapeseed methyl ester. Hydraulic characterization of an eight-hole nozzle was carried out using these three fuels, in order to explore and analyse the influence of the fuel properties on the mass flow rate and the momentum flux at the nozzle exit. Additionally, spray visualization tests were performed in order to obtain information about the spray cone angle, which allows characterization of the air-fuel mixing process. Finally, a theoretical derivation was used to obtain further details of the microscopic characteristics of the spray and to compare the air-fuel mixing efficiencies for the different biodiesel blends., This work was partly supported by Vicerrectorado de Investigacion, Desarrollo e Innovacion of the Universitat Politecnica de Valencia in the framework of the Project Estudio del Flujo en Toberas de Inyeccion Diesel Mediante Tecnicas LES (project no. 2837) and by Ministerio de Ciencia e Innovacion in the framework of the Project Estudio Teorico-experimental sobre la Influencia del Tipo de Combustible en Los Procesos de Atomizacion y Evaporacion del Chorro Diesel (project no. TRA2011-26293).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational study of the cavitation phenomenon and its interaction with the turbulence developed in diesel injector nozzles by Large Eddy Simulation (LES)

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Romero, José-Vicente|||0000-0003-3366-6557
  • Roselló, María-Dolores|||0000-0002-5724-7683
  • Martínez López, Jorge
Firstly, the code has been validated at real operating diesel engine conditions with experimental data in terms of mass flow, momentum flux and effective velocity, showing that the model is able to predict with a high level of confidence the behavior of the internal flow at cavitating conditions. Once validated, the code has allowed to study in depth the turbulence developed in the discharge orifices and its interaction with cavitation phenomenon. (C) 2011 Elsevier Ltd. All rights reserved., This work was partly sponsored by "Vicerrectorado de Investigacion, Desarrollo e Innovacion'' of the "Universitat Politecnica de Valencia'' in the frame of the project "Estudio numerico de la cavitacion en toberas de inyeccion Diesel mediante Grid Computing (Cavigrid)'', reference No. 2597 and by "Ministerio de Ciencia e Innovacion'' in the frame of the project "Estudio teorico-experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL)'', reference TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Using one-dimensional modeling to analyze the influence of the use of biodiesels on the dynamic behavior of solenoid-operated injectors in common rail systems: Results of the simulations and discussion

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Carreres, Marcos|||0000-0001-6430-6613
The influence of using biodiesel fuels on the hydraulic behavior of a solenoid operated common rail injection system has been explored by means of a one-dimensional model. This model has been previously obtained, including a complete characterization of the different components of the injector (mainly the nozzle, the injector holder and the electrovalve), and extensively validated by means of mass flow rate results under different conditions. After that, both single and multiple injection strategies have been analyzed, using a standard diesel fuel and rapeseed methyl ester (RME) as working fluids. Single long injections allowed the characterization of the hydraulic delay of the injector, the needle dynamics and the discharge capability of the couple injector-nozzle for the two fuels considered. Meanwhile, the effect of biodiesel on main plus post injection strategies has been evaluated in several aspects, such as the separation of the two injections or the effect of the main injection on the post injection fueling. Finally, a modification in the injector hardware has been proposed in order to have similar performances using biodiesel as the original injector configuration using standard diesel fuel., This work was sponsored by "Vicerrectorado de Investigacion, Desarrollo e Innovacion" of the "Universidad Politecnica de Valencia" in the frame of the project "Estudio numerico de la cavitacion en toberas de inyeccion Diesel mediante Grid Computing (Cavigrid)", Reference No. 2597 and by "Ministerio de Ciencia e Innovacion" in the frame of the Project "Estudio teorico experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL)", Reference No. TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Complete modelling of a piezo actuator last-generation injector for diesel injection systems

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Carreres, Marcos|||0000-0001-6430-6613
  • Plazas Torres, Alejandro Hernán
An experimental and computational study of an increasingly used third-generation common-rail injection system with a piezo actuator has been carried out. A complete characterization of the different elements of the system, both geometrically and hydraulically, has been performed in order to describe its behaviour. The information obtained through the characterization has been used to create a one-dimensional model that has been implemented in the commercial software AMESim and extensively validated against experimental data. The results of the validation demonstrate the model ability to predict the injection rate of the injector with a high level of accuracy, therefore, constituting a powerful tool in order to carry out further studies of this type of injection system., This work was supported by the Ministerio de Ciencia e Innovacion in the frame of the project 'Estudio teorico experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL)' [grant number TRA 2011-26293]. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A contribution to the understanding of cavitation effects in Diesel injector nozzles through a combined experimental and computational investigation

  • Payri, F.|||0000-0002-3314-4911
  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Martínez López, Jorge
In this paper a combined experimental and computational study was carried out in order to assess the ability of a homogeneous equilibrium model in predicting the experimental behaviour observed from the hydraulical characterization of a nozzle. The nozzle used was a six-orifice microsac nozzle, with cylindrical holes, and therefore inclined to cavitate. The experimental results available for the validation purpose comprised measurements of mass flow rate and spray momentum flux, which correctly combined provide also fundamental information such as discharge coefficient, nozzle exit effective velocity and area contraction. The model was proved to be able of reproducing the experimental results with high degree of confidence and, through the exploration of the internal flow, allowed the explanation of widely reported experimental findings related to cavitation phenomena: the mass flow choking induced by cavitation and the increment of effective injection velocity., This work was partly sponsored by "Vicerrectorado de lnvestigacion, Desarrollo e Innovacion" of the "Universitat Politecnica de Valencia" in the frame of the Project "Estudio del flujo en toberas de inyeccion diesel mediante tecnicas LES (LESFLOWGRID)", Reference No. 2837 and by "Ministerio de Ciencia e Innovacion" in the frame of the Project "Estudio teorico-experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), Reference TRA2011-26293. This support is gratefully acknowledged by the authors.