Pasar al contenido principal

ANALISIS MICROESTRUCTURAL, MECANICO Y DEL CRECIMIENTO CELULAR EN SOPORTES MACROPOROSOS PARA INGENIERIA TISULAR OSEA MEDIANTE TRATAMIENTO DE IMAGEN.

TEC2009-14128

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2009
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fibronectin distribution on demixed nanoscale topographies

  • Perez Garnes, Manuel
  • González García, Cristina
  • Salmerón Sánchez, Manuel
  • Moratal, David|||0000-0002-2825-3646
  • Rico Tortosa, Patricia María
[EN] Purpose: It is known that surface nanotopography influences cell adhesion and differentiation. Our aim is to analyze the effect of nanoscale topography on fibronectin adsorption and, afterwards, on cell adhesion in order to rationalize the cell-material interaction by focusing on the state of the intermediate layer of adsorbed fibronectin at the material interphase. Methods: Nanotopographic surfaces were produced by demixing of thin film polymer blends - PLLA and PS - during a high speed spin-casting process. Fibronectin (FN) was adsorbed on the different nanotopographies and the protein distribution was directly observed by atomic force microscopy (AFM). The fraction of the surface covered by the protein was quantified by image analysis, as well as the distribution of FN between peaks and valleys. Focal adhesion protein -vinculin- was immunostained and quantified by image analysis on the different nanoscale surfaces. Results: Different nanoscale domains were obtained by changing the composition of the system within a height range of 3 nm to 30 nm. FN tends to adsorb on the peaks of nanoisland topographies, especially in compositions that did not enhance cell adhesion. Moreover, protein distribution between valleys and peaks alters the size of focal adhesion plaques, which grew larger on surfaces with an even distribution of fibronectin. Conclusions: Our results suggest that the surface nanotopography is a key material property capable of influencing protein adsorption. Additionally, the distribution of the protein on the different samples was correlated to the initial ability of cells to adhere in terms of the size of the focal plaques. © 2011 Wichtig Editore., This studied was funded by the Spanish Ministry of Science and Innovation through MAT2009-14440-C02-01 and TEC2009-14128 grants. CIBER-BBN is an initiative funded by the VI National R&D&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund. This work was supported by funds for research in the field of Regenerative Medicine through the collaboration agreement with the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Micro-computed tomography image-based evaluation of 3D anisotropy degree of polymer scaffolds

  • Pérez Ramírez, María Úrsula
  • López Orive, Jesús Javier
  • Arana Fernandez de Moya, Estanislao
  • Salmerón Sánchez, Manuel
  • Moratal, David|||0000-0002-2825-3646
Anisotropy is one of the most meaningful determinants of biomechanical behaviour. This study employs micro-computed tomography (mu CT) and image techniques for analysing the anisotropy of regenerative medicine polymer scaffolds. For this purpose, three three-dimensional anisotropy evaluation image methods were used: ellipsoid of inertia (EI), mean intercept length (MIL) and tensor scale (t-scale). These were applied to three patterns (a sphere, a cube and a right prism) and to two polymer scaffold topologies (cylindrical orthogonal pore mesh and spherical pores). For the patterns, the three methods provided good results. Regarding the scaffolds, EI mistook both topologies (0.0158, [-0.5683; 0.6001]; mean difference and 95% confidence interval), and MIL showed no significant differences (0.3509, [0.0656; 0.6362]). T-scale is the preferable method because it gave the best capability (0.3441, [0.1779; 0.5102]) to differentiate both topologies. This methodology results in the development of non-destructive tools to engineer biomimetic scaffolds, incorporating anisotropy as a fundamental property to be mimicked from the original tissue and permitting its assessment by means of mu CT image analysis., The support of the Spanish Ministry of Science and Innovation through project TEC2009-14128 is acknowledged.