Pasar al contenido principal

DESARROLLOS COMPACTOS DE SUBSISTEMAS PASIVOS ESPACIALES EMPLEANDO TECNOLOGIA COAXIAL Y MATERIALES PERIODICOS SELECTIVOS EN FRECUENCIA

TEC2010-21520-C04-02

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDAD MIGUEL HERNANDEZ DE ELCHE
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Full-Wave Analysis of Periodic Dielectric Frequency-Selective Surfaces Under Plane Wave Excitation

  • Coves Soler, Angela
  • Marini, Stephan
  • Gimeno Martinez, Benito
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
A novel full-wave method for the modal characterization of dielectric electromagnetic band-gap structures under oblique plane wave excitation is presented, showing the dielectric lattice periodicity in both the longitudinal and the transverse propagation directions. In this method, an eigenvalue problem is obtained in terms of the generalized ABCD matrix of the periodic cell, whose solution provides not only the propagation constant of the fundamental Floquet mode, but also of the higher order modes of the global periodic structure. The proposed analysis technique has been successfully validated with a commercial software based on the frequency domain finite elementmethod. The transmittance of a finite periodic material with a finite number of unit cells has also been successfully verified through comparisons with other theoretical results reported in the technical literature. Then, our new algorithm has been used to study band-gap materials made of rectangular dielectric parallel rods, investigating the variation of the dispersion diagram and the transmission and reflection transfer functions when modifying both geometrical and electrical parameters of this structure. Finally, the response differences when a periodical defect is considered in a finite periodic arrangement have also been highlighted., This work was supported in part by the Ministerio de Ciencia e Innovacion under Grant TEC2010-21520-C04, Spain.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Low-Pass and Bandpass Filters With Ultra-Broad Stopband Bandwidth Based on Directional Couplers

  • Gómez-García, Roberto
  • Sánchez-Soriano, Miguel Ángel
  • Sánchez-Renedo, Manuel
  • Torregrosa-Penalva, Germán
  • Bronchalo, Enrique
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
The design of planar sharp-rejection low-pass and bandpass filters (LPFs and BPFs) featuring a very broad stopband is addressed in this paper. For the LPF case, two new classes of bandstop signal-interference transversal filtering section (TFS) consisting of power directional couplers in reflection mode are proposed. In the BPF application, additional short-circuit stubs are inserted at the TFS input/output accesses. Based on these filtering cells, the devised LPF and BPF approaches are then derived from the cascade of multiple TFSs with frequency-contiguous stopbands. Thus, an overall attenuated band showing an ultra-large spectral width and deep rejection levels through the generation of several transmission zeros (TZs) is synthesized. Furthermore, such unprecedented filtering performances are obtained for much lower circuit complexity than available solutions. The operating principle of the conceived LPF and BPF topologies and guidelines for their realization are detailed. This includes formulas for their analytically designable TZs. For practical validation, three LPF prototypes and one wideband BPF circuit are also fabricated in microstrip technology and tested.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Extended-stopband microstrip lowpass filter using rat-race directional couplers

  • Gómez-García, Roberto
  • Sánchez-Soriano, Miguel Ángel
  • Sánchez-Renedo, Manuel
  • Torregrosa-Penalva, Germán
  • Bronchalo, Enrique
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
A class of microstrip lowpass filter (LPF) with a sharp-rejection, ultra-broad stopband is reported. It employs rat-race directional couplers properly arranged to operate as bandstop transversal filtering sections (TFSs). The theoretical foundations of this LPF approach are described, and the performance control of its building bandstop TFS is verified. Moreover, a proof-of-concept microstrip LPF prototype with a 3 dB cutoff frequency of 1 GHz and a 20 dB stopband up to 5.86 GHz has been built and tested.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Rigorous evaluation of propagation losses in arbitrarily shaped waveguide structures using boundary integral - resonant mode expansion and perturbation of boundary conditions

  • Marini, Stephan
  • Soto Pacheco, Pablo
  • Mattes, Michael
  • Gimeno Martínez, Benito
  • Bleda, Sergio
  • Vidal Pantaleoni, Ana
  • Boria Esbert, Vicente Enrique
  • Bleda, Sergio|||/items/d2b99c60-360f-4a4f-a712-934a01eea569
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
The accurate consideration of propagation losses in arbitrarily shaped waveguide-based structures is studied in this paper. For such a purpose, a software tool based on the perturbation of the boundary conditions on the waveguide metallic walls and on the boundary integral - resonant mode expansion method has been developed. To show the advantages of the proposed technique with respect to the classic power-loss method, the complex propagation wavenumbers of a double ridge and an elliptical waveguide have been first computed and compared with results of a commercial software based on the finite element technique. Next a circular, a sectorial shaped and a triangular shaped waveguide have been considered. Then, a computer-aided design software package based on this modal analysis tool has been applied to predict the propagation loss effects in complex waveguide structures, such as an evanescent mode ridge waveguide filter, a traditional dual mode filter with circular cavities and a twist component for K-band applications.