Pasar al contenido principal

DISEÑO DE ARQUITECTURAS DE TRANSMISION RECONFIGURABLES ENERGETICAMENTE EFICIENTES PARA SISTEMAS DE COMUNICACIONES MOVILES DE PROXIMA GENERACION

TEC2014-58341-C4-2-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD DE ZARAGOZA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Radio-over-fiber linearization with optimized genetic algorithm CPWL model

  • Mateo, C.
  • Carro, P.L.
  • García-Dúcar, P.
  • Mingo, J. de
  • Salinas, I.
This article proposes an optimized version of a canonical piece-wise-linear (CPWL) digital predistorter in order to enhance the linearity of a radio-over-fiber (RoF) LTE mobile fronthaul. In this work, we propose a threshold allocation optimization process carried out by a genetic algorithm (GA) in order to optimize the CPWL model (GA-CPWL). Firstly, experiments show how the CPWL model outperforms the classical memory polynomial DPD in an intensity modulation/direct detection (IM/DD) RoF link. Then, the GA-CPWL predistorter is compared with the CPWL model in several scenarios, in order to verify that the proposed DPD offers better performance in different optical transmission conditions. Experimental results reveal that with a proper threshold allocation, the GA-CPWL predistorter offers very promising outcomes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Efficiency enhancement by reconfigurable matching networks in LINC transmitters

  • Mateo, C.
  • Carro, P.L.
  • Garcia-Ducar, P.
  • de Mingo, J.
  • Perez-Cisneros, J.R.
  • Sanchez-Perez, C.
This paper proposes the use of a transmitter based on a linear amplification with nonlinear components (LINC) architecture, in which the reconfigurable matching networks (RMNs) are included. By varying the RMN active cell number, it is possible to change the load impedance at the power amplifier (PA) output, improving the amplifier drain efficiency and therefore the efficiency of the whole system. A long-term evolution (LTE) downlink signal with a bandwidth of 1.4 MHz and a peak-to-average power ratio (PAPR) of 11.48 dB is applied in order to carry out the experiments. Results show that the use of the RMNs in a LINC architecture improves the efficiency at all tested frequencies, especially at 927 MHz reaching an enhancement of 36.50%. Regarding the distortion, the adjacent channel leakage ratio (ACLR) values increase in all cases, with an improvement of 3.5 dB at 958 MHz. Finally, in terms of error vector magnitude (EVM), the proposed architecture offers a value of 1.96% at 927 MHz.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Analytical and experimental performance evaluation of BLE neighbor discovery process including non-idealities of real chipsets

  • Pérez-Diaz de Cerio, David
  • Hernández, Ángela
  • Valenzuela, José Luis
  • Valdovinos, Antonio
The purpose of this paper is to evaluate from a real perspective the performance of Bluetooth Low Energy (BLE) as a technology that enables fast and reliable discovery of a large number of users/devices in a short period of time. The BLE standard specifies a wide range of configurable parameter values that determine the discovery process and need to be set according to the particular application requirements. Many previous works have been addressed to investigate the discovery process through analytical and simulation models, according to the ideal specification of the standard. However, measurements show that additional scanning gaps appear in the scanning process, which reduce the discovery capabilities. These gaps have been identified in all of the analyzed devices and respond to both regular patterns and variable events associated with the decoding process. We have demonstrated that these non-idealities, which are not taken into account in other studies, have a severe impact on the discovery process performance. Extensive performance evaluation for a varying number of devices and feasible parameter combinations has been done by comparing simulations and experimental measurements. This work also includes a simple mathematical model that closely matches both the standard implementation and the different chipset peculiarities for any possible parameter value specified in the standard and for any number of simultaneous advertising devices under scanner coverage.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Proposal and evaluation of BLE discovery process based on new features of bluetooth 5.0

  • Hernández-Solana, Ángela
  • Perez-Diaz-De-Cerio, David
  • Valdovinos, Antonio
  • Valenzuela, José Luis
The device discovery process is one of the most crucial aspects in real deployments of sensor networks. Recently, several works have analyzed the topic of Bluetooth Low Energy (BLE) device discovery through analytical or simulation models limited to version 4.x. Non-connectable and non-scannable undirected advertising has been shown to be a reliable alternative for discovering a high number of devices in a relatively short time period. However, new features of Bluetooth 5.0 allow us to define a variant on the device discovery process, based on BLE scannable undirected advertising events, which results in higher discovering capacities and also lower power consumption. In order to characterize this new device discovery process, we experimentally model the real device behavior of BLE scannable undirected advertising events. Non-detection packet probability, discovery probability, and discovery latency for a varying number of devices and parameters are compared by simulations and experimental measurements. We demonstrate that our proposal outperforms previous works, diminishing the discovery time and increasing the potential user device density. A mathematical model is also developed in order to easily obtain a measure of the potential capacity in high density scenarios.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Minimization of Feedback Loop Distortions in Digital Predistortion of a Radio-Over-Fiber System with Optimization Algorithms

  • Mateo, C.
  • Carro, P.L.
  • Garcia-Ducar, P.
  • De Mingo, J.
  • Salinas, I.
This article proposes the linearization of an intensity modulation/direct detection radio-over-fiber (RoF) link with feedback loop. The goal is to carry out the predistortion process in a real scenario, in which the output signals are a few kilometers far from the baseband unit (BBU). First, the feedback loop is considered ideal, so the output signals are captured at the remote radio head side. Then, the feedback loop is taken into account, and both the input and output signals are captured at the BBU side. Applying optimization algorithms, such as Fibonacci, Golden, or Powell, it is possible to seek the optimal attenuation value within only a few iterations, which minimizes the distortion of the feedback loop. Experiments are carried out in a RoF system with 10 and 25 km length fiber within the long-Term evolution (LTE) standard. Measured results show how with a proper choice of the attenuation it is possible to reach analogous results regarding to an ideal feedback loop in terms of adjacent channel power ratio, the output signal power and error vector magnitude.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Markov mode-multiplexing mode in OFDM outphasing transmitters

  • Carro, P.L.
  • Garcia-Ducar, P.
  • Mingo, J.
  • Valdovinos, A.
Outphasing transmitters have been explored to study the trade-off between linearity and efficiency. The outphasing technique enhances efficiency by operating two amplifiers at lower output amplitudes, using two constant envelope signals. Their major drawback is the inherent sensitivity to gain and phase imbalances between the two amplifier branches. Another important issue is related to the degradation of efficiency, especially in isolated combiners. This paper presents a Statistical Markov-Chain Mode-Multiplexing (MM) transmitter which combines features of the MM and Reverse MM-LINC. Commercial analog devices and a digital platform for signal processing purposes are used to test the performance with an orthogonal frequency multiplexing modulation (OFDM), which is one of the most used modulation schemes in wireless communication systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A low-cost tracking system for running race applications based on bluetooth low energy technology

  • Perez-Diaz-De-Cerio, D.
  • Hernández-Solana, Á.
  • Valdovinos, A.
  • Valenzuela, J.L.
Timing points used in running races and other competition events are generally based on radio-frequency identification (RFID) technology. Athletes’ times are calculated via passive RFID tags and reader kits. Specifically, the reader infrastructure needed is complex and requires the deployment of a mat or ramps which hide the receiver antennae under them. Moreover, with the employed tags, it is not possible to transmit additional and dynamic information such as pulse or oximetry monitoring, alarms, etc. In this paper we present a system based on two low complex schemes allowed in Bluetooth Low Energy (BLE): the non-connectable undirected advertisement process and a modified version of scannable undirected advertisement process using the new capabilities present in Bluetooth 5. After fully describing the system architecture, which allows full real-time position monitoring of the runners using mobile phones on the organizer side and BLE sensors on the participants’ side, we derive the mobility patterns of runners and capacity requirements, which are determinant for evaluating the performance of the proposed system. They have been obtained from the analysis of the real data measured in the last Barcelona Marathon. By means of simulations, we demonstrate that, even under disadvantageous conditions (50% error ratio), both schemes perform reliably and are able to detect the 100% of the participants in all the cases. The cell coverage of the system needs to be adjusted when non-connectable process is considered. Nevertheless, through simulation and experimental, we show that the proposed scheme based on the new events available in Bluetooth 5 is clearly the best implementation alternative for all the cases, no matter the coverage area and the runner speed. The proposal widely exceeds the detection requirements of the real scenario, surpassing the measured peaks of 20 sensors per second incoming in the coverage area, moving at speeds that range from 1.5 m/s to 6.25 m/s. The designed real test-bed shows that the scheme is able to detect 72 sensors below 600 ms, fulfilling comfortably the requirements determined for the intended application. The main disadvantage of this system would be that the sensors are active, but we have proved that its consumption can be so low (9.5 µA) that, with a typical button cell, the sensor battery life would be over 10, 000 h of use.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

GaN HEMT Class-E Rectifier for DC plus AC Power Recovery

  • Ruiz, M.N.
  • Vegas, D.
  • Perez-Cisneros, J.R.
  • Garcia, J.A.
A 915 MHz GaN HEMT-based class-E rectifier is proposed in this paper to be used for DC+AC wireless power recovery. Taking advantage of the time reversal (TR) duality principle, the rectifier was derived from a class-E inverter, whose output network was designed for high-efficiency operation over a wide range of resistive loads. The addition of an appropriate gate-side termination allows the device to be turned-on without an additional RF source for gate driving. The rectifier reduced sensitivity to load variation, as well as its capability for efficiently and linearly recovering the envelope of an AM RF excitation, were then characterized. An average efficiency of 82% has been measured for the combined RF-to-DC and RF-to-AC power conversion of a 1.6 W modulated carrier. Frequency multiplexing and frequency modulation alternatives for high-level DC+AC wireless power transmission are finally presented.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Anti-Collision Adaptations of BLE Active Scanning for Dense IoT Tracking Applications

  • Hernandez-Solana, A.
  • Perez-Diaz-De-Cerio, D.
  • Valdovinos, A.
  • Valenzuela, J.L.
Bluetooth low energy (BLE) is one of most promising technologies to enable the Internet-of-Things (IoT) paradigm. The BLE neighbor discovery process (NDP) based on active scanning may be the core of multiple IoT applications in which a large and varying number of users/devices/tags must be detected in a short period of time. Minimizing the discovery latency and maximizing the number of devices that can be discovered in a limited time are challenging issues due to collisions between frames sent by advertisers and scanners. The mechanism for resolution of collisions between scanners has a great impact on the achieved performance, but backoff in NDP has been poorly studied so far. This paper includes a detailed analysis of backoff in NDP, identifies and studies the factors involved in the process, reveals the limitations and problems presented by the algorithm suggested by the specifications and proposes simple and practical adaptations on scanner functionality. They are easily compatible with the current definitions of the standard, which together with a new proposal for the backoff scheme, may significantly improve the discovery latencies and, thus, the probability of discovering a large number of devices in high density scenarios.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Evaluation of Radio Resource Management Impact on RoF Signal Transmission for Downlink LTE

  • Carro, P.L.
  • Hernandez-Solana, A.
  • Valdovinos Bardaji, A.
Analog radio-over-fiber (RoF) is a suitable technology for efficiently developing the cloud-RAN concept in fifth generation deployments based on long-term evolution advanced (LTE-A). Distortion and radiofrequency (RF) power amplifier gain should be taken into account in order to achieve the desired transmission power at the base station. Both mainly depend on several parameters that characterize the optical link, such as the RF input power and bias current. This paper analyzes the link performance due to variations on the traffic load as expected under real operation. In this paper, we show that it is possible in this scenario to adaptively choose the optimum RF input power to minimize the measured error vector magnitude and reduce the RF subsystem gain. Results show that this adaptation allows to relax the RF amplifier gain requirements up to 3-4 dB for medium load conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

DPD Linearization Complexity Reduction of Remote Radio Heads in C-RAN with Radio over Fiber Fronthaul

  • Carro, P.L.
  • Mateo, C.
  • Garcia-Ducar, P.
  • De Mingo, J.
  • Valdovinos, A.
Radio-over-Fiber (RoF) is a suitable technology for efficiently developing the cloud-RAN concept in Fifth Generation (5G) deployments based on Long Term Evolution Advanced LTE-A. Distortion coming out from the radiofrequency (RF) power amplifier should be taken into account in order to achieve the desired performance at the base station. In this paper, a complexity reduction technique based on a variable degree polynomial predistorter is proposed. The obtained results show that it is possible to achieve a reduction of operations with a penalty of 1.6 dB in ACLR and negligible impact on the EVM.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Low-cost test measurement setup for real IoT BLE sensor device characterization

  • Perez-Diaz-de-Cerio, D.
  • Hernández-Solana, Á.
  • Valdovinos, A.
  • Olmos, J.
  • Valenzuela, J.L.
The methodology presented in this paper aims to characterize impairments shown by real devices which are usually neglected on standardized tests but that become very important in massive IoT scenarios. For instance, we have measured that real BLE scanners are not able to scan continuously even though they are configured to do so. Besides, we have also found and demonstrated that some manufacturers seem not to apply any backoff mechanism although it is mandatory. These two unexpected behaviors have a significant impact on the performance of massive wireless sensor networks based on BLE. So, it becomes necessary to characterize these and other impairments. The proposed tests are based on device current consumption measurements and their association with the information obtained from upper layers. We describe a new low-cost generic measurement setup and provide all the necessary data (configuration parameters, scripts, etc.) for applying the proposed methodology. As an example, we use it to profile the behavior of Bluetooth Low Energy devices. Furthermore, the proposed setup can also inspire researchers to characterize other wireless technology devices, like Wi-Fi, Zigbee, LoRa, etc.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

RoF SpatialMux MIMO-LTE Fronthaul System Transmission Parameter Selection with Nelder-Mead Optimization Algorithm

  • Mateo, C.
  • Carro, P.L.
  • Garcia-Ducar, P.
  • De Mingo, J.
  • Salinas, I.
In this paper the optimization of the transmission conditions in a multiple-input multiple-output (MIMO) Radio-over-Fiber (RoF) system by applying the Nelder-Mead method is proposed. With this algorithm it is possible to seek the optimum RF signal power and the bias current of both lasers in few iterations. The experiments have been carried out in a MIMO IM/DD RoF system, where MIMO signals are wavelength multiplexed. The signals and the carrier frequency belong to the LTE standard. Experimental results show that fast convergence is accomplished under different bandwidths yielding to good tradeoff between noise and non-linearity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Evaluation of Nonlinear Effects in a RoF SpatialMux MIMO-LTE Fronthaul System

  • Mateo, C.
  • Carro, P.L.
  • Garcia-Ducar, P.
  • De Mingo, J.
  • Salinas, I.
This paper analyzes the optimum transmission conditions of a radio-over-fiber (RoF) fronthaul system in multiple-input multiple-output (MIMO) schemes. By varying different transmission parameters, such as the laser bias current or the input signal power, it is possible to minimize the nonlinear effects produced by the RoF system. The experimental setup consists of an intensity modulation/direct detection (IM/DD) scheme with 10 km-length. The carrier frequency is set to 2.65 GHz, within the band 7 of the LTE standard. LTE MIMO signals with several bandwidths and modulations are applied in order to carry out the experiments. Results show that with a properly bias current and input signal power it is possible to minimize the distortions of the system, improving Adjacent Channel Power Ratio (ACPR) and Error Vector Magnitude (EVM) values.