Pasar al contenido principal

ARQUITECTURAS RADAR MULTI-MODO AVANZADAS CON INCORPORACION DE HARDWARE DE RADIOFRECUENCIA ULTRA-RECONFIGURABLE Y MULTI-FUNCIONAL

TEC2017-82398-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Exploiting Parasitic Capacitances in 3-D Inductors to Design RF CMOS Quasi-Elliptic-Type Broad-Band Bandpass Filters

  • Zhu, Xi
  • Gómez García, Roberto|||0000-0001-9132-6927
A class of RF broad-band bandpass filter (BPF) with quasi-elliptic-type response in low-cost bulk CMOS technology is reported. It is based on the in-series cascade connection of lowpass and highpass filtering stages with 3-D inductors, whose parasitic capacitances are properly exploited. Specifically, they are used to transform the basic inductor into an LC tank, thus allowing to generate an upper transmission zero (TZ) that increases filtering selectivity and out-of-band power-rejection levels in a spurious-free/extended upper stopband. The layout of a basic third-order BPF cell shaped by four 3-D inductors and its lossless equivalent lumped-element circuit are detailed. By means of this lossless equivalent lumped-element model, its scalability to higher-order BPF designs by in-series cascading various BPF-cell replicas is also demonstrated. For experimental-validation purposes, an on-chip RF CMOS BPF prototype with 11-GHz center frequency and 68.5% 3-dB fractional bandwidth is developed using a 0.13-mu m bulk CMOS technology. According to the measured results, it shows an upper stopband with minimum attenuation of 31.7 dB from 22.5 GHz to 67 GHz, alongside with TZs at 3.5 GHz and 22.5 GHz to produce sharp-rejection filtering., Spanish Ministry of Economy Industry and Competitiveness State Research Agency
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Input-reflectionless low-pass filter on multilayered diplexer-based topology

  • Yang, Li|||0000-0002-1264-4810
  • Gómez García, Roberto|||0000-0001-9132-6927
  • Muñoz Ferreras, José María|||0000-0003-1929-3934
  • Zhang, Runqi
A class of two-layered input-reflectionless diplexer-based LPF is reported in this letter. By using a resistively-terminated wideband microstrip vertical transition by the first time for this application, an input-reflectionless response for the conceived LPF device is realized. The RF operational foundations and theoretical examples of this input-reflectionless LPF design approach have been shown and experimentally verified with the development and characterization of a two-LPF-unit microstrip prototype with extended reflectionless stopband., Ministerio de Economía, Industria y Competitividad, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Balanced quasi-elliptic-type combline diplexer with multiextracted-pole junction/output sections

  • Gómez García, Roberto|||0000-0001-9132-6927
  • Yang, Li|||0000-0002-1264-4810
  • Muñoz Ferreras, José María|||0000-0003-1929-3934
A class of coupled-multiline quasi-elliptic-type balanced diplexer device with closely spaced channels and its balanced coupling-routing-diagram formalism to simultaneously model its differential- and common-mode operation are reported. It employs third-order combline-type bandpass filters (BPFs) in its filtering channels, whose resonating lines are connected at one of their extremes to the symmetry plane of the balanced-circuit structure (i.e., virtual grounds for the differential mode), along with a multiextracted-pole/coupled-multiline dual-band BPF junction and single-band BPF output cells. In differential-mode operation, the dual-band BPF junction adds one in-band pole to each diplexer channel and three transmission zeros (TZs) to both channels, whereas the single-band BPF output cells incorporate one in-band pole and two TZs in their corresponding channels. In this manner, increased-selectivity differential-mode BPF transfer functions for the diplexer channels when compared to those of its third-order combline-type BPFs are obtained. Grounded resistors are connected at the symmetry plane of the balanced diplexer for all the resonating lines of the combline-type BPFs, which become detuned with regard to the poles associated with the dual-band BPF junction and the single-band BPF output cells under common-mode excitation. This allows for high common-mode suppression levels in wide spectral ranges to be realized for both channels while maintaining the same TZs as in differential-mode operation. For practical-validation purposes, a 1.6-GHz/1.8-GHz microstrip prototype is manufactured and tested., Ministerio de Economía, Industria y Competitividad, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Optimisation-based design of transversal signal-interference microwave bandpass and lowpass filters with extended stopband

  • Gómez García, Roberto|||0000-0001-9132-6927
  • Yang, Li|||0000-0002-1264-4810
  • Muñoz Ferreras, José María|||0000-0003-1929-3934
Generalised bi-path stepped-impedance-line signal-interference bandpass and lowpass transversal filtering sections (TFSs) with increased stopband bandwidth above the main transmission band are presented. They are realised by partitioning the two in-parallel transmission-line paths in their related classic spectrally periodic TFS approach into a plurality of line sub-segments, whose characteristic-impedance and electrical-length values are derived through optimisation. It is demonstrated that the stopband range above the transmission band in these generalised non-frequency-periodic TFSs can be remarkably broadened with regard to those intrinsic to their conventional bandpass and lowpass TFS counterparts. Furthermore, as added benefits, this is achieved for shorter transmission-line paths and a sharper cut-off slope between the transmission band and the extended stopband. For experimental-validation purposes, three proof-of-concept microstrip prototypes are manufactured and characterised. They correspond to a 1-GHz bandpass TFS, a 1-GHz two-TFS-in-series-cascade-based bandpass filter (BPF) with augmented selectivity and out-of-band power-rejection levels, and one lowpass TFS with a designed 3-dB cut-off frequency of 1.25 GHz., Agencia Estatal de Investigación, European Commission