Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Processing and optimization of laser-activated Cu and Ni inks for ceramic tile inkjet printing

  • Lahlahi-Attalhaoui, Abderrahim
  • Porcar García, Samuel
  • González Cuadra, Jaime
  • Toca Valero, Santiago Luis
  • Fraga Chiva, Diego
  • Jordán, M. D.
  • Cervera, I.
  • Fuente, Germán F. de la
  • Carda, Juan B.
This study presents a technique for the metallization of ceramic surfaces under ambient conditions, using metallic inks activated through direct laser writing. This process represents a significant advancement in surface processing technology in the ceramic tile industry. The method involves crystallizing metallic coatings directly onto the ceramic surface, using a Cu or Ni polymer coordination complex. A uniform and vitrified metallic coating is formed on the ceramic when exposed to pulsed laser irradiation at 1064 nm. X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM) analysis confirm the formation of face-centered cubic phases of Cu and Ni. Scanning Electron Microscopy (SEM) analysis reveals spherical grains embedded in the matrix with diameters smaller than 150 nm. TEM analysis confirms the presence of crystals with an average size smaller than 20 nm, which induce Surface Plasmon Resonance (SPR) effects. The absorption effect observed at 450 and 350 nm, indicated by UV–Vis Diffuse Reflectance Spectroscopy, is attributed to the surface plasmon resonance effects of Cu and Ni particles on the glass coating. X-ray Photoelectron Spectroscopy (XPS) analysis confirms the laser-induced redox transformation of Cu(II) and Ni(II) precursor complexes into reduced Cu(0) and Ni(0) nanoparticles, while also confirming the formation of a thin oxide coating of CuO and NiO on the surface. This approach holds great potential for digital ceramic decoration due to the scalable nature of this technique., The authors wish to express their gratitude to the Ajuntament de Vila-real for their support through the Cátedra de Innovación Cerámica 'Ciutat de Vila-real' and to the Solid State Chemistry Research Group of the Universitat Jaume I for their invaluable contributions. They also extend their thanks to the Generalitat Valenciana for the funding provided through the predoctoral (CIACIF/2022/277) and postdoctoral (CIAPOS/2023/425) contracts, co-financed by the European Social Fund. The authors acknowledge the Valencian Agency for Research for their support of the project INNEST/2024/420. They also thank the State Research Agency for funding the project TED2021-130963B-C22 (reference: AEI/10.13039/501100011033/European Union NextGenerationEU/PRTR). Additionally, the authors express their gratitude to the Spanish Ministry of Science and Innovation for their support through the project PID2020-116719RB-C43 (MCIN/AEI/10.13039/501100011033). Finally, the authors extend their appreciation to the Universitat Jaume I, particularly the Central Scientific Instrumentation Service, for their technical and scientific support, as well as to the Government of Aragón for their backing through the research group T54_23R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrafast development of blue pigment for in situ laser digital coloration in the ceramic industry

  • Lahlahi-Attalhaoui, Abderrahim
  • González Cuadra, Jaime
  • Porcar García, Samuel
  • Toca Valero, Santiago Luis
  • Fraga Chiva, Diego
  • Fuente, Germán F. de la
  • Carda, Juan B.
This study presents a fast and simple method for digital ceramic coloration using inkjet printing, eliminating the need for traditional precalcined pigments. This innovative approach represents a breakthrough in ceramic decoration technology, and introduces a previously unexplored methodology. In this work, CoAl₂O₄ spinel, a pigment commonly used in industrial contexts, is synthesized through laser zone melting (LZM) by applying pulsed laser radiation at 1064 nm. A standardized methodology to optimize pigment quality is developed, based on laser parameters such as pulse width, frequency, speed, power, and line spacing. Scanning electron microscopy (SEM) is used to determine the optimal laser conditions for obtaining a continuous, defect-free coating, showing that the embedded particles on the surface exhibit a nearly spherical morphology with diameters below 100 nm. The sample with the highest surface quality is further analyzed structurally and optically. X-ray diffraction (XRD) confirms the presence of a pure spinel phase without secondary phases, along with a vitreous phase due to pigment embedding. Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy reveal the characteristic vibrational bands of a normal spinel structure. The intense blue color is confirmed by strong absorption at 560 nm in ultraviolet–visible (UV–Vis) spectroscopy, as well as b* and Δb* values of 29 and 1.58, respectively, compared to the traditional pigment. This synthesis approach significantly enhances digital ceramic coloration compared to other methods evaluated in this study, offering a scalable, flexible, and more efficient alternative suitable for industrial-scale production., The authors wish to express their gratitude to the Municipal Council of Vila-real for its support through the “Ciutat de Vila-real” Chair in Innovation in Ceramics, and to the Solid State Chemistry Research Group of the Universitat Jaume I for their invaluable contributions. They also extend their thanks to the Generalitat Valenciana for the funding provided through the predoctoral (CIACIF/2022/277), postdoctoral (CIAPOS/2023/425), and international predoctoral mobility (CIBEFP/2024/008) contracts cofinanced by the European Social Fund. The authors are grateful to the Valencian Agency for Research for its support of the project INNEST/2024/420. They also thank the State Research Agency for funding the project TED2021-130963B-C22 (reference: AEI/10.13039/501100011033/European Union NextGenerationEU/PRTR). Additionally, the authors express their gratitude to the Spanish Ministry of Science and Innovation for their support through the project PID2020-116719RB-C43 (MCIN/AEI/10.13039/501100011033). Finally, the authors extend their appreciation to the Universitat Jaume I, particularly the Central Scientific Instrumentation Service, for their technical and scientific support, as well as to the Government of Aragón for their backing through the research group T54_23R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-temperature, high-throughput spatial atomic layer deposition of NiOx nanocrystalline thin films from [Ni(ipki)2]

  • Porcar, Samuel
  • Schmickler, Marcel
  • Okcu, Hayri
  • Obenlüneschloß, Jorit
  • D'Ercole, Stefano
  • Cervera Gabalda, Laura
  • Galarreta-Rodriguez, Itziar
  • Rubio-Zuazo, Juan
  • González Cuadra, Jaime
  • Lahlahi, Abderahim
  • Fraga, Diego
  • Sanchez-Velasquez, Camilo
  • Bellet, Daniel
  • Fix, Thomas
  • Carda, Juan B.
  • Devi, Anjana
  • Muñoz-Rojas, David
Spatial atomic layer deposition (SALD) is a recent ALD variant enabling much faster deposition rates, even at atmospheric pressure, making it ideal for scalable, low-cost devices. NiOx, a transparent p-type oxide, is widely used in emerging technologies like perovskite solar cells. However, no suitable SALD process for NiO thin films has been reported so far. In this work, we present the deposition of nanocrystalline NiOx thin films via SALD using a recent Ni precursor not yet explored for the ALD of NiO, namely, bis(4-(isopropylamino)pent-3en-2-onato)nickel(II) or [Ni(ipki)2]. O2 has been used as coreactant, with higher deposition rates being achieved if H2O is added to the O2 flow. A narrow ALD window has been obtained between 230 °C and 250 °C, where a GPC of 0.023 nm is observed. This corresponds to a deposition rate of 1.4 nm/min, which is 2 to 10 times faster than the rates reported for conventional ALD of NiO thin films. Remarkably, the growth onset of NiOx starts around only 170 °C. The transmittance of the films reaches nearly 97 % in the visible for 55 nm thick films. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies revealed a high homogeneity of the films. X-ray diffraction (XRD), Raman spectroscopy and X-ray absorption spectroscopy (XAS) studies confirm the presence of a cubic NiOx crystalline phase. Finally, NiOx films have been deposited on Ag nanowire networks, demonstrating the possibility of depositing homogeneous and conformal coatings with this new process., The authors would like to express their gratitude for the financial support provided by several research initiatives: the FOTOCER project (PID2020–116149GB-I00), funded by MCIN/AEI/10.13039/501100011033; the CLUSCERM project (TED2021–130963B-C22), supported by MCIN/AEI/10.13039/501100011033 and the European Union’s NextGenerationEU/PRTR initiative; and the CLUSKER project (INNEST/2024/420), funded by the Valencian Institute of Business Competitiveness (IVACE). Additional support was received from the, jointly funded by ANR (project number 21-CE08–0047) and DFG (project number 490773082). The work has also benefited from funding under the Investissement d’Avenir (PIA) program – LabEx MINOS. Furthermore, the authors acknowledge support through the postdoctoral fellowship CIAPOS/2023/425 and the predoctoral fellowship CIACIF/2022/277, both co-financed by the Valencian regional government and the European Social Fund. Authors also want to thank the “Cátedra de Innovación Cerámica 'Ciutat de Vila-real' de l’Universitat Jaume I” for the financial support. We also acknowledge the Spanish Ministerio de Ciencia, Innovación y Universidades and Consejo Superior de Investigaciones Científicas for financial support and for provision of synchrotron radiation facilities through the projects 2010 6 0E 013, 2021 60 E 030 and CEX2024-001445-S., With funding form the Spanish government through the "Severa Ochoa Centre of Excellence" accreditation (CEX2024-001445-S)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Processing and optimization of laser-activated Cu and Ni inks for ceramic tile inkjet printing

  • Lahlahi-Attalhaoui, A.
  • Porcar, S.
  • Cuadra, J.G.
  • Toca, S.
  • Fraga, D.
  • Jordán, M.D.
  • Cervera, I.
  • Fuente, G.F. de la
  • Carda, J.B.
This study presents a technique for the metallization of ceramic surfaces under ambient conditions, using metallic inks activated through direct laser writing. This process represents a significant advancement in surface processing technology in the ceramic tile industry. The method involves crystallizing metallic coatings directly onto the ceramic surface, using a Cu or Ni polymer coordination complex. A uniform and vitrified metallic coating is formed on the ceramic when exposed to pulsed laser irradiation at 1064 nm. X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM) analysis confirm the formation of face-centered cubic phases of Cu and Ni. Scanning Electron Microscopy (SEM) analysis reveals spherical grains embedded in the matrix with diameters smaller than 150 nm. TEM analysis confirms the presence of crystals with an average size smaller than 20 nm, which induce Surface Plasmon Resonance (SPR) effects. The absorption effect observed at 450 and 350 nm, indicated by UV–Vis Diffuse Reflectance Spectroscopy, is attributed to the surface plasmon resonance effects of Cu and Ni particles on the glass coating. X-ray Photoelectron Spectroscopy (XPS) analysis confirms the laser-induced redox transformation of Cu(II) and Ni(II) precursor complexes into reduced Cu(0) and Ni(0) nanoparticles, while also confirming the formation of a thin oxide coating of CuO and NiO on the surface. This approach holds great potential for digital ceramic decoration due to the scalable nature of this technique.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrafast development of blue pigment for in situ laser digital coloration in the ceramic industry

  • Lahlahi-Attalhaoui, Abderrahim
  • González Cuadra, Jaime
  • Porcar García, Samuel
  • Toca Valero, Santiago Luis
  • Fraga Chiva, Diego
  • Fuente, Germán F. de la
  • Carda, Juan Bautista
This study presents a fast and simple method for digital ceramic coloration using inkjet printing, eliminating the need for traditional precalcined pigments. This innovative approach represents a breakthrough in ceramic decoration technology, and introduces a previously unexplored methodology. In this work, CoAl₂O₄ spinel, a pigment commonly used in industrial contexts, is synthesized through laser zone melting (LZM) by applying pulsed laser radiation at 1064 nm. A standardized methodology to optimize pigment quality is developed, based on laser parameters such as pulse width, frequency, speed, power, and line spacing. Scanning electron microscopy (SEM) is used to determine the optimal laser conditions for obtaining a continuous, defect‐free coating, showing that the embedded particles on the surface exhibit a nearly spherical morphology with diameters below 100 nm. The sample with the highest surface quality is further analyzed structurally and optically. X‐ray diffraction (XRD) confirms the presence of a pure spinel phase without secondary phases, along with a vitreous phase due to pigment embedding. Fourier‐transform infrared spectroscopy (FTIR) and Raman spectroscopy reveal the characteristic vibrational bands of a normal spinel structure. The intense blue color is confirmed by strong absorption at 560 nm in ultraviolet–visible (UV–Vis) spectroscopy, as well as b* and Δb* values of 29 and 1.58, respectively, compared to the traditional pigment. This synthesis approach significantly enhances digital ceramic coloration compared to other methods evaluated in this study, offering a scalable, flexible, and more efficient alternative suitable for industrial‐scale production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

In situ formation of Ni- and Cr-doped cobalt ferrite pigment in glassy matrix films via laser zone melting

  • Lahlahi-Attalhaoui, A.
  • Porcar, S.
  • Toca, S.
  • Cuadra, J.G.
  • Nebot-Diaz, I.
  • Bakali, J.
  • Mirjolet, M.
  • Kim, M.
  • Franco, C.
  • Pané, S.
  • de la Fuente, G.F.
  • Carda, J.B.
Doped cobalt ferrites (CFO, CoFe₂O₄) are black pigments of considerable interest in ceramic systems, although their conventional production requires high-temperature calcination followed by milling to control particle size. In this work, laser zone melting (LZM) is proposed as an alternative route for the in situ formation and consolidation of CFO spinels directly on the surface, avoiding both pre-synthesis and post-micronization. A precursor layer prepared from milled powders was activated using a high-power nanosecond fiber laser. Irradiance and pulse overlap were systematically varied, identifying an optimal processing window at Oₚ ≈ 97%, with a scanning speed of 2000 mm/s and an irradiance of 3.49 MW/cm². The resulting coatings exhibited distinct crystalline phases together with a vitreous fraction that enabled the integration of ∼200 nm particles into the surface, and L* values as low as 30.55. These findings highlight LZM as a promising route toward ceramic industry electrification and decarbonization.