Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of chitin nanocrystals on the dielectric behaviour and conductivity of chitosan-based bionanocomposites

  • Salaberria, A.M.
  • Badia, J.D.
  • Fernandes, S.C.M.
  • Sáenz de Juano-Arbona, V.
  • Labidi, J.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] A series of bionanocomposite films based on chitosan, reinforced with chitin nanocrystals, were developed, and assessed in terms of dielectric behaviour and conductivity by using an experimental methodology that allows avoiding the conductivity contribution and the exclusion of contact and interfacial polarization effects. The dielectric relaxations at low and high frequency and temperatures were modeled by Havriliak-Negami functions. Below the glass transition temperature (Tg), the gamma and beta relaxations were observed, which were related to intramolecular and non-cooperative segmental movements. At higher temperatures, an intermolecular and cooperative macromolecular movement, related to the glass transition, gave rise to alpha-relaxation. In addition, two over-Tg p(I) and p(II) relaxations were found, which were related to the displacement of dipoles in the disordered structure of bionanocomposites. The addition of chitin nanocrystals did not affect the apparent activation energy Ea of the gamma-relaxation. However, it decreased the Ea of the beta-relaxation and increased the free volume at temperatures in the vicinities of the alpha-relaxation. Finally, the electric conductivity of the bionanocomposites was lower than that of neat chitosan and chitin due to the interaction between the-OH and-NH2 groups that reduced the ionic mobility, along with the increase of free volume, with the subsequent separation of phases., The European Regional Development Funds and the Spanish Ministry of Science and Innovation for the concession of Research Projects ENE2014-53734-C2-1-R, UPOV13-3E-1947 and ENE2017-86711-C3-1-R are appreciated. Generalitat Valenciana is acknowledged for the project APOSTD14/041 for JD Badia and GRISOLIA/2002/003 for R. Teruel-Juanes. The authors are thankful for the financial support from the Department of Education of the Basque Government (IT1008-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dielectric spectroscopy of novel thiol-ene/epoxy thermosets obtained from allyl-modified hyperbranched poly(ethyleneimine) and diglycidylether of bisphenol A

  • Badia, J.D.
  • Acebo, C.
  • Gil-Castell, O.
  • Serra, A.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Dielectric Thermal Analysis (DETA) of a series of new thermoset obtained by click chemistry was performed. The new thermosets were obtained by a dual-curing process consisting in a first photochemical thiol-ene, followed by a thermal thiol-epoxy starting from an allyl-terminated hyperbranched poly(ethyleneimine) (HBPEI) and different proportions of diglycidylether of bisphenol A (DGEBA) and the corresponding stoichiometric proportions of pentaerythritol tetrakis (3-mercaptopropionate, PETMP). The dielectric behaviour was obtained experimentally supressing the conductive effects. Two sub-Tg intramolecular non-cooperative gamma and beta relaxations and an intermolecular cooperative alpha-relaxation were detected. The gamma-relaxation was ascribed to the dipole orientation of the terminal thiol groups. Two gamma relaxations gamma(epo) and gamma(ene) were observed, according to the influence of the surroundings. Only thermosets with a content of flexible HBPEI/PETMP domains higher than a 50% w/w showed the gamma(ene) relaxation at lower temperatures and higher frequencies. The beta-relaxation was a non-Johari-Goldstein relaxation, ascribed to the dipole transfer of the linear -CH2-O-(C=O)-CH2-CH2- groups of the thiol constrained in the glassy state. The alpha-relaxation was ascribed to the long-term segmental movements of the thermosets, occurring during the transition from the glassy to the rubbery stage. A synergic effect of reducing the rigidity and compactness of the thermosets by the reduction of aromatic moieties of the DGEBA/PETMP units, and the increase of the flexibility induced by the addition of HBPEI/PETMP units affected the macromolecular movement of the thermosets., European Regional Development Funds and the Spanish Ministry of Science, Innovation and Universities for ENE2017-86711-C3-1-R, MAT2017-82849-C2-1-R, ENE2014-53734-C2-1-R, UPOV13-3E-1947 and projects. Ministry of Education for the FPU13/01916) for O. Gil-Castell. Generalitat de Catalunya for the 2017-SGR-77 project. Generalitat Valenciana for the APOSTD14/041 for JD Badia and GRISOLIA/2012/003 for R. Teruel-Juanes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of hydrothermal ageing on the thermal stability, morphology and viscoelastic performance of PLA/sisal biocomposites

  • Gil Castell, Óscar
  • Badía Valiente, José David
  • Kittikorn, T.
  • Strömberg, E.
  • Ek, Martina
  • Karlsson, S.
  • Ribes-Greus, A.|||0000-0003-2460-8291
The influence of the combined exposure to water and temperature on the behaviour of polylactide/sisal biocomposites coupled with maleic acid anhydride was assessed through accelerated hydrothermal ageing. The biocomposites were immersed in water at temperatures from 65 to 85 °C, between the glass transition and cold crystallisation of the PLA matrix. The results showed that the most influent factor for water absorption was the percentage of fibres, followed by the presence of coupling agent, whereas the effect of the temperature was not significant. Deep assessment was devoted to biocomposites subjected to hydrothermal ageing at 85 °C, since it represents the extreme degrading condition. The morphology and crystallinity of the biocomposites were evaluated by means of X-Ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The viscoelastic and thermal performance were assessed by means of dynamic mechanic thermal analysis (DMTA) and thermogravimetry (TGA). The presence of sisal generally diminished the thermal stability of the biocomposites, which was mitigated by the addition of the coupling agent. After composite preparation, the effectiveness of the sisal fibre was improved by the crystallisation of PLA around sisal, which increased the storage modulus and reduced the dampening factor. The presence of the coupling agent strengthened this effect. After hydrothermal ageing, crystallisation was promoted in all biocomposites therefore showing more fragile behaviour evidencing pores and cracks. However, the addition of coupling agent in the formulation of biocomposites contributed in all cases to minimise the effects of hydrothermal ageing., The authors would like to acknowledge the Spanish Ministry of Economy and Competitiveness, through the Research Project ENE2014-53734-C2-1-R and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is also thanked for the pre-doctoral FPU grant of O. Gil-Castell (FPU13/01916). Generalitat Valenciana is thanked for the APOSTD14/041 program for J.D. Badia. The Chilean Government is thanked for the 13CEI2-21839 project. The financial support given by the Prince of Songkla University and KTH Royal Institute of Technology is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the dissolution time into an acid hydrolytic solvent to taylor electrospun nanofibrous polycaprolactone scaffolds

  • Gil-Castell, O.
  • Badia, J.D.
  • Strömberg, E.
  • Karlsson, S.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The hydrolysis of the polycaprolactone (PCL) as a function of the dissolution time in a formic/acetic acid mixture was considered as a method for tailoring the morphology of nanofibrous PCL scaffolds. Hence the aim of this research was to establish a correlation between the dissolution time of the polymer in the acid solvent with the physicochemical properties of the electrospun nanofibrous scaffolds and their further service life behaviour. The physico-chemical properties of the scaffolds were assessed in terms of fibre morphology molar mass and thermal behaviour. A reduction of the molar mass and the lamellar thickness as well as an increase of the crystallinity degree were observed as a function of dissolution time. Bead-free fibres were found after 24 and 48 h of dissolution time with similar diameter distributions. The decrease of the fibre diameter distributions along with the apparition of beads was especially significant for scaffolds prepared after 72 h and 120 h of dissolution time in the acid mixture. The service life of the obtained devices was evaluated by means of in vitro validation under abiotic physiological conditions. All the scaffolds maintained the nanofibrous structure after 100 days of immersion in water and PBS. The molar mass was barely affected and the crystallinity degree and the lamellar thickness increased along immersion preventing scaffolds from degradation. Scaffolds prepared after 24 h and 48 h kept their fibre diameters whereas those prepared after 72 h and 120 h showed a significant reduction. This PCL tailoring procedure to obtain scaffolds that maintain the nanoscaled structure after such long in vitro evaluation will bring new opportunities in the design of long-term biomedical patches. (C) 2016 Elsevier Ltd. All rights reserved., The European Regional Development Funds and the Spanish Ministry of Economy and Competitiveness are acknowledged for the projects POLYCELL (ENE2014-53734-C2-1-R) and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is thanked for the pre-doctoral FPU grant of O. Gil-Castell (FPU13/01916) and the scholarship for a research stage of 0. Gil-Castell in Kungliga Tekniska Hogskolan (KTH). Generalitat Valenciana is thanked for the APOSTD/2014/041 for J.D. Badia. Universitat de Valencia (UV) and HS LaFe are acknowledged for the DERMASAFE project. The financial support given by the ICTH Royal Institute of Technology and the Universitat Politecnica de Valencia (UPV) are gratefully acknowledged. IESMAT S.A. and Malvern Instruments Ltd are recognised for their grateful collaboration.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tailored electrospun nanofibrous polycaprolactone/gelatin scaffolds into an acid hydrolytic solvent system

  • Gil-Castell, O.
  • Badia, J.D.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Blended nanofibrous scaffolds based on polycaprolactone (PCL) and gelatin (Ge) were successfully prepared. A formic/acetic acid (1:1) mixture was used to dissolve PCL/Ge blends from 100/0 to 20/80 %wt in steps of 10 %wt. The hydrolysis of the PCL diluted in the formic/acetic acid mixture was considered as a method for tailoring the surface morphology and physicochemical features of the nanofibrous PCL/Ge scaffolds as a function of the dissolution time. The fibre diameter remained in the nanoscale range for all the studied scaffolds, which is crucial to mimic the extra-cellular matrix size. The reduction of the intrinsic viscosity, molar mass and hydrodynamic radius found for the PCL molecules as a function of the dissolution time, consequently diminished the entanglement capability of the polymeric chains. Subsequently, the fibre diameter decreased as dissolution time increased, for all the studied compositions. While the crystallinity of the scaffolds with high PCL content increased as a function of the dissolution time, the scaffolds with high percentage of Ge showed the lowest crystallinity degree, which was ascribed to the hindering effect of the Ge diffused among the PCL segments. The wettability increased as a function of the Ge content due to the high hydrophilic behaviour of these molecules. It also increased as a function of the dissolution time, due to the more hydroxyl groups available in PCL segments to interact with water molecules. As a whole, the physicochemical assessment of the electrospun scaffolds revealed an effective tailoring procedure to obtain functionalised PCL/Ge scaffolds with specific properties as a function of the dissolution time before electrospinning., The Spanish Ministry of Economy and Competitiveness is acknowledged for the projects POLYCELL (ENE2014-53734-C2-1-R), POLYDECARBOCELL (ENE2017-86711-C3-1-R) and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is thanked for the pre-doctoral FPU grant of O. Gil-Castell (FPU13/01916). Generalitat Valenciana is thanked for the APOSTD/2014/041 for J.D. Badia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Performance of sulfonated poly(vinyl alcohol)/graphene oxide polyelectrolytes for direct methanol fuel cells

  • Gil-Castell, Óscar
  • Santiago, Óscar
  • Navarro, Emilio
  • Leo, Teresa J.
  • B. Pascual-Jose|||0000-0001-7562-916X
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The use nanotechnology along with the consideration of a functionalization and stabilization approach to the poly(vinyl alcohol) (PVA) was considered useful for the preparation of cost-effective polyelectrolyte membranes. A set of nanocomposite and crosslinked membranes based in PVA/SSA/GO were prepared and analyzed as polyelectrolytes in direct methanol fuel cells (DMFCs). The crosslinking and sulfonation by the use of sulfosuccinic acid (SSA) enhanced the stability and increased the proton conducting sites in the PVA structure. The presence of graphene oxide (GO) augmented the stability, remarkably decreased the methanol crossover and enhanced power density curves. An optimum value for proton conductivity was found for the 0.50%wt of GO proportion, which decreased to higher concentrations of GO. Given the power density curve dependency on both the proton conductivity and the crossover reduction, the performance of these membranes as polyelectrolytes in DMFCs is strictly related to the balance between both factors. Therefore, a proportion of GO of 0.75%wt may assure suitable proton conductivity 3 mS·cm-1 and high resistance to methanol permeability, reaching promising power density of 16 mW·cm-2 with lower hydration levels., The Spanish Ministry of Economy, Industry, and Competitiveness is acknowledged for the projects ENE2017-86711-C3-1-R, ENE2017-86711-C3-2-R, ENE2017-90932-REDT, and UPOV13-3E-1947. The Spanish Ministry of Education, Culture, and Sports is thanked for the predoctoral FPU grant for O. Gil-Castell (grant no. FPU13/01916).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Crosslinked chitosan/poly(vinyl alcohol)-based polyelectrolytes for proton exchange membranes

  • Gil-Castell, O.
  • Arenga, Francesca
  • Salaberria, A. M.
  • Baschetti, M.G.
  • Labidi, J.
  • Badia, J.D.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The preparation polyelectrolytes based on crosslinked poly(vinyl alcohol) (PVA) and chitosan (CS) was considered as a feasible alternative to develop highly functionalised, cost-effective and eco-friendly membranes for proton exchange fuel cell technologies. CS/PVA-based membranes were combined with sulfosuccinic acid (SSA) as crosslinking and sulfonating agent, and glycerol (GL) to promote flexibility and favour their manageability. The chemical structure, the thermo-oxidative behaviour, the ethanol uptake, the electric, the proton conductivity, and the performance in direct ethanol fuel cell (DEFC) were assessed. In general, all the CS/PVA-based polyelectrolytes showed a synergetic increase of thermo-oxidative stability, appropriate absorption and diffusion of ethanol and good proton conductivity, suitable for the typical service conditions of fuel cells. The GL in the membranes reacted with SSA, reduced the ethanol absorption, diffusion coefficient and proton conductivity, but acted as a plasticiser that increased the ductile manageability of the polyelectrolytes to be mounted on the membrane-electrode assembly (MEA). Higher presence of CS and higher the proportion of GL in the polyelectrolyte, improved the material performance in the DEFC. In particular, the crosslinked polyelectrolyte 40CS/PVA/SSA/20GLwith a 40 %wt. of CS referred to PVA, and a 20 %wt. of GL referred to CS, showed a suitable behaviour in the DEFC test, with a maximum value of power density of 746 mW·cm-2., The Spanish Ministry of Economy, Industry and Competitiveness is acknowledged for the projects ENE2017-86711-C3-1-R and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is thanked for the pre-doctoral FPU grant for O. Gil-Castell (FPU13/01916)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Suitability of blends from virgin and reprocessed polylactide: performance and energy valorization kinetics

  • Gil-Castell, O.
  • Badia, J.D.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] A blending strategy of virgin and reprocessed polylactide may be postulated as an alternative to reduce the material cost at industrial level, and as a valorisation route to plastic waste management of production scraps. The performance of blends prepared from virgin polylactide and polylactide mechanically reprocessed up to two cycles (PLA-V/R) was assessed in terms of thermo-oxidative stability, morphology, viscoelasticity and thermal kinetics for energetic valorisation. PLA-V/R blends showed appropriate thermo-oxidative stability. The amorphous nature of polylactide was preserved after blending. The viscoelastic properties showed an increment of the mechanical blend effectiveness, which suggested the feasibility of PLA-V/R blends to be used under similar mechanical conditions to those of virgin PLA goods. Finally, it was shown that the energetic valorisation of PLA-V/R blends would result in a more feasible process, due to the lower required activation energy, thus highlighting the advantages of the energetic demand for the process. In conclusion, PLA-V/R blends showed similar processability, service performance and valorisation routes than virgin PLA and therefore could be relevant in the sustainable circular industry of bioplastics., The authors would like to thank the support of the European Regional Development Fund and the Spanish Ministry of Economy and Competitiveness, through the Research Projects ENE2014-53734-C2-1-R and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is also thanked for the FPU grant for O. Gil-Castell (FPU13/01916). Generalitat Valenciana is recognized for the APOSTD14/041 program for J.D. Badia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of sisal and hydrothermal ageing on the dielectric behaviour of polylactide/sisal biocomposites

  • Badia, J.D.
  • Reig-Rodrigo, P.
  • Kittikorn, T.
  • Strömberg, E.
  • Ek, M.
  • Karlsson, S.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The dielectric properties of virgin polylactide (PLA) and its reinforced composites with different weight amounts of sisal fibres were assessed at broad temperature (from - 130 degrees C to 130 degrees C) and frequency ranges (from 10(-2)-10(7) Hz), before and after being subjected to accelerated hydrothermal ageing. The synergetic effects of both the loading of sisal and hydrothermal ageing were analysed by means of dielectric relaxation spectra. The relaxation time functions were evaluated by the Havriliak-Negami model, substracting the ohmic contribution of conductivity. The intramolecular and intermolecular relaxations were respectively analysed by means of Arrhenius and Vogel-Fulcher-Tammann-Hesse thermal activation models. The addition of fibre increased the number of hydrogen bonds, which incremented the dielectric permittivity and mainly hindered the non-cooperative relaxations of the biocomposites by increasing the activation energy. Hydrothermal ageing enhanced the formation of the crystalline phase at the so-called transcrystalline region along sisal. This fact hindered the movement of the amorphous PLA fraction, and consequently decreased the dielectric permittivity and increased the dynamic fragility. (C) 2017 Elsevier Ltd. All rights reserved., The authors acknowledge the European Regional Development Fund and the Spanish Ministry of Economy and Competitiveness, through the Research Projects ENE2014-53734-C2-1-R and UPOV13-3E-1947. The Regional Valencian Government is thanked for the APOSTD14/041 program for J.D. Badia. The financial support given by the Prince of Songkla University and KTH Royal Institute of Technology is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Relevant factors for the eco-design of polylactide/sisal biocomposites to control biodegradation in soil in an end-of-life scenario

  • Badia, J.D.
  • Strömberg, E.
  • Kittikorn, T.
  • Ek, M.
  • Karlsson, S.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The eco-design considers the factors to prepare biocomposites under an end-of-life scenario. PLA/sisal biocomposites were obtained from amorphous polylactide and sisal loadings of 10, 20 and 30 wt% with and without coupling agent, and subjected to biodegradation in soil according to standard IS0846. Mass loss, differential scanning calorimetry and size-exclusion chromatography were used for monitoring biodegradation. A statistical factorial analysis based on the molar mass M-n, and crystallinity degree X-c pointed out the relevance and interaction of amount of fibre and use of coupling agent with the time of burial in soil., During the preparation of biocomposites, chain scission provoked a similar reduction of M-n, for coupled and non-coupled biocomposites. The amount of fibre was relevant for the increase of Xc due to the increase of nucleation sites. The coupling agent accelerated the evolution of both factors: reduction of M-n, and the consequent increase of Xc, mainly during biodegradation in soil. Both factors should be balanced to facilitate microbial assimilation of polymer segments, since bacterial digestion is enhanced by chain scission but blocked by the promotion of crystalline fractions. (C) 2017 Elsevier Ltd. All rights reserved., The authors would like to acknowledge the European Regional Development Funds and the Spanish Ministry of Economy and Competitiveness, through the Research Projects ENE2014-53734-C2-1-R and UPOV13-3E-1947. Generalitat Valenciana is thanked for the APOSTDI4/041 program for J.D. Badia. The financial support given by the Prince of Songkla University and KTH Royal Institute of Technology is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical recycling of polylactide, upgrading trends and combination of valorization techniques

  • Badia, J.D.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The upcoming introduction of polylactides in the fractions of polymer waste encourages technologists to ascertain its valorization at the best quality conditions. Mechanical recycling of PLA represents one of the most cost-effective methodologies, but the recycled materials are usually directed to downgraded applications, due to the inherent thermomechanical degradation affecting its mechanical, thermal and rheological performance. In this review, the current state of mechanical recycling of PLA is reported, with special emphasis on a multi-scale comparison among different studies. Additionally, the applications of physical and chemical upgrading strategies, as well as the chances to blend and/or composite recycled PLA are considered. Moreover, the different valorization techniques that can be combined to optimize the value of PLA goods along its life cycle are discussed. Finally, a list of different opportunities to nurture the background of the mechanical recycling of PLA is proposed, in order to contribute to the correct waste management of PLA wastes. (C) 2016 Elsevier Ltd. All rights reserved., The authors acknowledge the Spanish Ministry of Economy and Competitiveness for the projects POLYCELL (ENE2014-53734-C2-1-R) and TETRA-SEC (UPOV13-3E-1947). The Chilean Corporation for the Promotion of Productivity (CORFO) is thanked for the funding of project CEN-Chile (13CEI2-21839). Generalitat Valenciana is recognized for the BIOARMED project (APOSTD/2014/041) for J.D. Badia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Polylactide-based self-reinforced composites biodegradation: Individual and combined influence of temperature, water and compost

  • Gil-Castell, O.
  • Badia, J.D.
  • Ingles-Mascaros, S.
  • Serra, A.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Self-reinforced polymer composites (SRCs) are proposed as a suitable alternative for composite development, based in the combination of a polymeric matrix and a polymeric fibre made of the same polymer. SRCs based in polylactide (PLA) could be fully biodegradable and their valorisation routes could presumably be assimilated to those for neat PEA. In this sense, the aim of this study was to develop new self-reinforced PLA-based composites and ascertain their biodegradability. For this purpose, PLA-based SRCs were obtained through a thermo-compression procedure and their biodegradability corroborated under standard conditions (ISO 20200). Moreover, a deep study of the effect of the different factors involved in the biodegradation of the composites such as the temperature, the water and the compost medium was considered relevant to delimitate the long-term properties and valorisation routes for these materials. The macroscopic and microscopic appearance as well as the thermo-oxidative stability, the thermal properties and the molar mass were evaluated. Although degradation was perceived due to the effect of temperature, the synergistic combination of water and temperature and compost was found to play a key role in the biodegradation of these materials. Overall, these SRCs can be considered as promising candidates, since their end-of-life management options can be guaranteed under standardised composting conditions. (C) 2018 Elsevier Ltd. All rights reserved., The authors would like to thank the support of the European Regional Development Fund and the Spanish Ministry of Economy and Competitiveness, through the Research Projects ENE2014-53734-C2-1-R and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is also thanked for the FPU grant for O. Gil-Castell (FPU13/01916). Generalitat Valenciana is recognised for the APOSTD14/041 program for J.D. Badia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrospun Poly(ethylene-co-vinyl alcohol)/Graphene Nanoplatelets Composites of Interest in Intelligent Food Packaging Applications

  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
  • Echegoyen, Y.
  • Badia, Jose D.
  • Lagaron Cabello, José María
[EN] Graphene nanoplatelets (GNPs) were synthetized from graphite powder and, thereafter, embedded in poly(ethylene-co-vinyl alcohol) (EVOH) fibers by electrospinning in the 0.1-2 wt.-% range. The morphological, chemical, and thermal characterization performed on the electrospun nanocomposite fibers mats revealed that the GNPs were efficiently dispersed and rolled along the EVOH fibrilar matrix up to contents of 0.5 wt.-%. Additionally, the dielectric behavior of the nanocomposite fibers was evaluated as a function of the frequency range and GNPs content. The obtained results indicated that their dielectric constant rapidly decreased with the frequency increase and only increased at low GNPs loadings while the nanocomposite fiber mats became electrically conductive, with the maximum at 0.5 wt.-% GNPs content. Finally, the electrospun mats were subjected to a thermal post-treatment and dark films with a high contact transparency were obtained, suggesting that the nanocomposites can be used either in a nonwoven fibers form or in a continuous film form. This study demonstrates the potential of electrospinning as a promising technology to produce GNPs-containing materials with high electrical conductivity that can be of potential interest in intelligent packaging applications as "smart" labels or tags., This research was funded by the European Regional Development Funds (ERDF) and Ministry of Science, Innovation, and Universities (MICIU) project numbers ENE2014-53734-C2-1-R, ENE2017-86711-C3-1-R, UPOV13-3E-1947, and AGL2015-63855-C2-1-R. S.T.-G. acknowledges the MICIU for his Juan de la Cierva contract (IJCI-2016-29675). J.D.B. and R.T.-J. also thank Generalitat Valenciana (GV) for their projects APOSTD14/041 and GRISOLIA/2012/003, respectively.