Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publication Artículo científico (JournalArticle)

Robust anti-icing superhydrophobic aluminum alloy surfaces by grafting fluorocarbon molecular chains

  • Rico, V.
  • Mora, Julio
  • García, Paloma
  • Agüero, Alina
  • Borrás, A.
  • González Elipe, A.R.
  • López-Santos, C.
Infusion of low surface tension liquids in nanostructured surfaces is currently used to promote an anti-icing response, although the long term stability of these systems is often jeopardized by losses of the infused liquid. In this work, we propose an alternative to the infusion procedure to induce a more effective and long lasting anti-icing capacity. The method consists of a combination of surface nanostructuration with the chemical grafting of fluorocarbon molecules. Al6061 substrates have been subjected to laser roughening and further modified with a nanostructured Al2O3 thin film to achieve a dual roughness and porous surface state. These surfaces have been subjected to a grafting treatment with perfluorooctyltriethoxysilane (PFOTES) vapor or, for comparative purposes, infused with a low surface tension liquid. A comparative analysis of the wetting, water condensation and anti-icing properties of these two systems showed an outstandingly better performance for the grafted surfaces with respect to the infused ones. Grafted surfaces were markedly superhydrophobic and required higher water vapor pressures to induce condensation. When looking for their anti-icing capacity, they presented quite long freezing delay times for supercooled water droplets (i.e. almost four hours) and exhibited a notably low ice accretion in a wind tunnel test. The high aging resistance and durability of these grafted surfaces and the reproducibility of the results obtained when subjected to successive ice accretion cycles show that molecular grafting is an efficient anti-icing methodology that, in aggressive media, may outperform the classical infusion procedures. The role of the fluorocarbon chains anchored on the surface in inducing an anti-icing functionality is discussed., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors want to specially thank Airbus Group Innovations DE, Concordia Institute of Aerospace Design & Innovation of Concordia University and Department of Engineering Physics of Polytechnique Montreal for, respectively, the rain erosion, thermal cycling and sand erosion tests carried out within the frame of this project. The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00, PID2019-110430GB-C21 and CSIC 201860E050) for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US” (VI PPIT-US).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydrophobicity, freezing delay, and morphology of laser-treated aluminum surfaces

  • Rico, Víctor J.
  • López-Santos, Carmen
  • Villagrá, Martín
  • Espinós, J.P.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Borrás, Ana
  • González-Elipe, Agustín R.
Until recently, superhydrophobicity was considered as a hint to predict surface icephobicity, an association of concepts that is by no means universal and that has been proven to depend on different experimental factors and material properties, including the actual morphology and chemical state of surfaces. This work presents a systematic study of the wetting and freezing properties of aluminum Al6061, a common material widely used in aviation, after being subjected to nanosecond pulsed IR laser treatments to modify its surface roughness and morphology. All treated samples, independent of their surface finishing state, presented initially an unstable hydrophilic wetting behavior that naturally evolved with time to reach hydrophobicity or even superhydrophobicity. To stabilize the surface state and to bestow the samples with a permanent and stable hydrophobic character, laser-treated surfaces were covered with a thin layer of CFx prepared by plasma-enhanced chemical vapor deposition. A systematic comparison between freezing delay (FD) and wetting properties of water droplets onto these plasma-/polymer-modified laser-treated surfaces that, under conditions where a heterogeneous nucleation mechanism prevails, surface morphology rather than the actual value of the surface roughness parameter the key feature for long FD times. In particular, it is found that surface morphologies rendering a Cassie–Baxter wetting regime longer FDs than those characterized by a Wenzel-like wetting state. It is that laser treatment, with or without additional coverage with thin CFx coatings, affects wetting and ice formation behaviors and might be an efficient procedure to mitigate icing problems on metal surfaces., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055 and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

3D organic nanofabrics: plasma-assisted synthesis and antifreezing behavior of superhydrophobic and lubricant-infused slippery surfaces

  • Alcaire, Maria
  • López-Santos, Carmen
  • Aparicio, Francisco J.
  • Sánchez-Valencia, J. R.
  • Obrero, José M.
  • Saghi, Zineb
  • Rico, Víctor J.
  • Fuente, Germán F. de la
  • González-Elipe, Agustín R.
  • Barranco, Ángel
  • Borrás, Ana
Herein, we present the development of supported organic nanofabrics formed by a conformal polymer-like interconnection of small-molecule organic nanowires and nanotrees. These organic nanostructures are fabricated by a combination of vacuum and plasma-assisted deposition techniques to generate step by step, single-crystalline organic nanowires forming one-dimensional building blocks, organic nanotrees applied as three-dimensional templates, and the polymer-like shell that produces the final fabric. The complete procedure is carried out at low temperatures and is compatible with an ample variety of substrates (polymers, metal, ceramics; either planar or in the form of meshes) yielding flexible and low solid-fraction three-dimensional nanostructures. The systematic investigation of this progressively complex organic nanomaterial delivers key clues relating their wetting, nonwetting, and anti-icing properties with their specific morphology and outer surface composition. Water contact angles higher than 150° are attainable as a function of the nanofabric shell thickness with outstanding freezing-delay times (FDT) longer than 2 h at −5 °C. The role of the extremely low roughness of the shell surface is settled as a critical feature for such an achievement. In addition, the characteristic interconnected microstructure of the nanofabrics is demonstrated as ideal for the fabrication of slippery liquid-infused porous surfaces (SLIPS). We present the straightforward deposition of the nanofabric on laser patterns and the knowledge of how this approach provides SLIPS with FDTs longer than 5 h at −5 °C and 1 h at −15 °C., We thank the AEI, MINECO (MAT2016-79866-R), and Consejerıa de Economia y Conocimiento de la Junta de Andalucia (US-1263142), the EU through cohesion fund and FEDER 20014-2020 programs and H2020 Phobic2Ice project(ref 690819) for financial support. This project has received funding from the EU-H2020 research and innovation program under the grant agreement No. 654360 (Id285) having benefitted from the access provided by CEA-Leti in Grenoble (France) within the framework of the NFFA-Europe Transnational Access Activity. F.J.A. and J.R.S.-V. acknowledge the Juan de la Cierva and Ramon y Cajal Programs, respectively. C.L.-S. and J.R.S.-V. thank the University of Seville through the VI PPIT-US., Peer reviewed