Skip to main content

NANOSTRUCTURED MULTILAYERED ARCHITECTURES FOR THE DEVELOPMENT OF OPTOFLUIDIC RESPONSIVE DEVICES, SMART LABELS AND ADVANCED SURFACE FUNCTIONALIZATION

MAT2016-79866-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 47
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publication Artículo científico (JournalArticle)

Robust anti-icing superhydrophobic aluminum alloy surfaces by grafting fluorocarbon molecular chains

  • Rico, V.
  • Mora, Julio
  • García, Paloma
  • Agüero, Alina
  • Borrás, A.
  • González Elipe, A.R.
  • López-Santos, C.
Infusion of low surface tension liquids in nanostructured surfaces is currently used to promote an anti-icing response, although the long term stability of these systems is often jeopardized by losses of the infused liquid. In this work, we propose an alternative to the infusion procedure to induce a more effective and long lasting anti-icing capacity. The method consists of a combination of surface nanostructuration with the chemical grafting of fluorocarbon molecules. Al6061 substrates have been subjected to laser roughening and further modified with a nanostructured Al2O3 thin film to achieve a dual roughness and porous surface state. These surfaces have been subjected to a grafting treatment with perfluorooctyltriethoxysilane (PFOTES) vapor or, for comparative purposes, infused with a low surface tension liquid. A comparative analysis of the wetting, water condensation and anti-icing properties of these two systems showed an outstandingly better performance for the grafted surfaces with respect to the infused ones. Grafted surfaces were markedly superhydrophobic and required higher water vapor pressures to induce condensation. When looking for their anti-icing capacity, they presented quite long freezing delay times for supercooled water droplets (i.e. almost four hours) and exhibited a notably low ice accretion in a wind tunnel test. The high aging resistance and durability of these grafted surfaces and the reproducibility of the results obtained when subjected to successive ice accretion cycles show that molecular grafting is an efficient anti-icing methodology that, in aggressive media, may outperform the classical infusion procedures. The role of the fluorocarbon chains anchored on the surface in inducing an anti-icing functionality is discussed., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors want to specially thank Airbus Group Innovations DE, Concordia Institute of Aerospace Design & Innovation of Concordia University and Department of Engineering Physics of Polytechnique Montreal for, respectively, the rain erosion, thermal cycling and sand erosion tests carried out within the frame of this project. The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00, PID2019-110430GB-C21 and CSIC 201860E050) for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US” (VI PPIT-US).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Surface chemistry and germination improvement of Quinoa seeds subjected to plasma activation

  • Gómez-Ramírez, Ana
  • López-Santos, Carmen
  • Cantos, Manuel
  • García Fernández, José Luis
  • Molina, Rodrigo
  • Cotrino, José
  • Espinós, J.P.
  • González-Elipe, Agustín R.
12 páginas.-- 7 figuras.-- 1 tabla .-- 55 referencias.-- Supplementary information accompanies this paper at doi:10.1038/s41598-017-06164-5, Plasma treatment is recognized as a suitable technology to improve germination efficiency of numerous seeds. In this work Quinoa seeds have been subjected to air plasma treatments both at atmospheric and low pressure and improvements found in germination rate and percentage of success. Seed water uptake by exposure to water vapor, although slightly greater for plasma treated seeds, did not justify the observed germination improvement. To identify other possible factors contributing to germination, the chemical changes experienced by outer parts of the seed upon plasma exposure have been investigated by X-ray photoemission spectroscopy (XPS) and scanning electron microscopy (SEM-EDX). XPS revealed that the outer layers of the Quinoa plasma treated seeds were highly oxidized and appeared enriched in potassium ions and adsorbed nitrate species. Simultaneously, SEM-EDX showed that the enrichment in potassium and other mineral elements extended to the seed pericarp and closer zones. The disappearance from the surface of both potassium ions and nitrate species upon exposure of the plasma treated seeds to water vapor is proposed as a factor favoring germination. The use of XPS to study chemical changes at seed surfaces induced by plasma treatments is deemed very important to unravel the mechanisms contributing to germination improvement., We thank EU-FEDER funds and the MINECO (projects MAT2013-40852-R, MAT2016-79866-R, MINECO-CSIC 201560E055) and RECUPERA 2020 and Junta de Andalucía (project P12-2265 MO) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In Vitro and in Vivo Study of Poly(Lactic–co–Glycolic) (PLGA) Membranes Treated with Oxygen Plasma and Coated with Nanostructured Hydroxyapatite Ultrathin Films for Guided Bone Regeneration Processes

  • Torres-Lagares, Daniel
  • Castellanos-Cosano, Lizett
  • Serrera-Figallo, María-Ángeles
  • García-García, Francisco J.
  • López-Santos, Carmen
  • Barranco, Ángel
  • González-Elipe, Agustín R.
  • Rivera-Jiménez, Cristóbal
  • Gutiérrez-Pérez, José-Luis
The novelty of this study is the addition of an ultrathin layer of nanostructured hydroxyapatite (HA) on oxygen plasma modified poly(lactic–<i>co</i>–glycolic) (PLGA) membranes (PO<sub>2</sub>) in order to evaluate the efficiency of this novel material in bone regeneration. Methods: Two groups of regenerative membranes were prepared: PLGA (control) and PLGA/PO<sub>2</sub>/HA (experimental). These membranes were subjected to cell cultures and then used to cover bone defects prepared on the skulls of eight experimental rabbits. Results: Cell morphology and adhesion of the osteoblasts to the membranes showed that the osteoblasts bound to PLGA were smaller and with a lower number of adhered cells than the osteoblasts bound to the PLGA/PO<sub>2</sub>/HA membrane (<i>p</i> < 0.05). The PLGA/PO<sub>2</sub>/HA membrane had a higher percentage of viable cells bound than the control membrane (<i>p</i> < 0.05). Both micro-CT and histological evaluation confirmed that PLGA/PO<sub>2</sub>/HA membranes enhance bone regeneration. A statistically significant difference in the percentage of osteoid area in relation to the total area between both groups was found. Conclusions: The incorporation of nanometric layers of nanostructured HA into PLGA membranes modified with PO<sub>2</sub> might be considered for the regeneration of bone defects. PLGA/PO<sub>2</sub>/HA membranes promote higher osteosynthetic activity, new bone formation, and mineralisation than the PLGA control group., This study has been subsidised by the Consejería de Salud of the Junta de Andalucia through project PI-0047-2013: “Innovation in Nanomedicine: Guided Bone Regeneration with Nanofunctionalised Resorbable Membranes (Nanorog)”. The authors also thank the AEI (EU FEDER program Project MAT2016-79866-R), We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Energy-sensitive ion- and cathode-luminescent radiation-beam monitors based on multilayer thin-film designs

  • Gil-Rostra, J.
  • Ferrer, F. J.
  • Espinós, J.P.
  • González-Elipe, Agustín R.
  • Yubero, Francisco
A multilayer luminescent design concept is presented to develop energy-sensitive radiation-beam monitors on the basis of colorimetric analysis. Each luminescent layer within the stack consists of rare-earth-doped transparent oxides of optical quality and a characteristic luminescent emission under excitation with electron or ion beams. For a given type of particle beam (electron, protons, α particles, etc.), its penetration depth and therefore its energy loss at a particular buried layer within the multilayer stack depend on the energy of the initial beam. The intensity of the luminescent response of each layer is proportional to the energy deposited by the radiation beam within the layer, so characteristic color emission will be achieved if different phosphors are considered in the layers of the luminescent stack. Phosphor doping, emission efficiency, layer thickness, and multilayer structure design are key parameters relevant to achieving a broad colorimetric response. Two case examples are designed and fabricated to illustrate the capabilities of these new types of detector to evaluate the kinetic energy of either electron beams of a few kilo-electron volts or α particles of a few mega-electron volts., The authors thank financial support from TEP-8067 (Junta de Andalucia/FEDER, UE), MAT2013-40852-R (MINECO/FEDER, UE) and MAT2016-79866-R (AEI/FEDER, UE) projects., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multicolored emission and lasing in DCM-adamantane plasma nanocomposite optical films

  • Alcaire, María
  • Cerdán, L.
  • Lahoz, F.
  • Aparicio, Francisco J.
  • González, J. C.
  • Ferrer, F. J.
  • Borrás, Ana
  • Espinós, J.P.
  • Barranco, Ángel
We present a low-temperature versatile protocol for the fabrication of plasma nanocomposite thin films to act as tunable emitters and optical gain media. The films are obtained by the remote plasma-assisted deposition of a 4-(dicyano-methylene)-2-methyl-6-(4-dimethylamino-styryl)-4H-pyran (DCM) laser dye alongside adamantane. The experimental parameters that determine the concentration of the dye in the films and their optical properties, including light absorption, the refractive index, and luminescence, are evaluated. Amplified spontaneous emission experiments in the DCM/adamantane nanocomposite waveguides show the improvement of the copolymerized nanocomposites’ properties compared to films that were deposited with DCM as the sole precursor. Moreover, one-dimensional distributed feed-back laser emission is demonstrated and characterized in some of the nanocomposite films that are studied. These results open new paths for the optimization of the optical and lasing properties of plasma nanocomposite polymers, which can be straightforwardly integrated as active components in optoelectronic devices., The authors thank the European Regional Development Funds program (EU-FEDER), the Junta de Andalucia (TEP8067), and the Spanish Ministry of Economy and Competitiveness (Project Nos. MAT2016-79866-R, MAT2013-40852-R, MAT2013-42900-P, MAT2014-51937-C3-1-P, RECUPERA 2020, and IJCI-2014-21226) for their financial support., Peer reviewed, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In situ determination of the water condensation mechanisms on superhydrophobic and superhydrophilic titanium dioxide nanotubes

  • Macías-Montero, M.
  • López-Santos, Carmen
  • Filippin, Nicolas
  • Rico, Víctor J.
  • Espinós, J.P.
  • Fraxedas, J.
  • Pérez-Dieste, Virginia
  • Escudero, Carlos
  • González-Elipe, Agustín R.
  • Borrás, Ana
One-dimensional (1D) nanostructured surfaces based on high-density arrays of nanowires and nanotubes of photoactive titanium dioxide (TiO2) present a tunable wetting behavior from superhydrophobic to superhydrophilic states. These situations are depicted in a reversible way by simply irradiating with ultraviolet light (superhydrophobic to superhydrophilic) and storage in dark. In this article, we combine in situ environmental scanning electron microscopy (ESEM) and near ambient pressure photoemission analysis (NAPP) to understand this transition. These experiments reveal complementary information at microscopic and atomic level reflecting the surface wettability and chemical state modifications experienced by these 1D surfaces upon irradiation. We pay special attention to the role of the water condensation mechanisms and try to elucidate the relationship between apparent water contact angles of sessile drops under ambient conditions at the macroscale with the formation of droplets by water condensation at low temperature and increasing humidity on the nanotubes' surfaces. Thus, for the as-grown nanotubes, we reveal a metastable and superhydrophobic Cassie state for sessile drops that tunes toward water dropwise condensation at the microscale compatible with a partial hydrophobic Wenzel state. For the UV-irradiated surfaces, a filmwise wetting behavior is observed for both condensed water and sessile droplets. NAPP analyses show a hydroxyl accumulation on the as-grown nanotubes surfaces during the exposure to water condensation conditions, whereas the water filmwise condensation on a previously hydroxyl enriched surface is proved for the superhydrophilic counterpart., We thank the Junta de Andalucia (TEP8067, FQM-196, and P12-FQM-2265), the European Regional Development Funds program (EU-FEDER), and the AEI and MINECO (projects MAT2013-40852-R, MAT2013-42900-P, MINECO-CSIC 201560E055, and MAT2016-79866-R) for financial support,, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Self-assembly of the non-planar Fe(III) phthalocyanine small-molecule: unraveling the impact on the magnetic properties of organic nanowires

  • Filippin, Nicolas
  • López-Flores, Víctor
  • Rojas, T. Cristina
  • Saghi, Zineb
  • Rico, Víctor J.
  • Sánchez-Valencia, J. R.
  • Espinós, J.P.
  • Zitolo, Andrea
  • Viret, Michel
  • Midgley, Paul A.
  • Barranco, Ángel
  • Borrás, Ana
In this article we show for the first time the formation of magnetic supported organic nanowires (ONWs) driven by self-assembly of a nonplanar Fe(III) phthalocyanine chloride (FePcCl) molecule. The ONWs grow by a crystallization mechanism on roughness-tailored substrates. The growth methodology consists of a vapor deposition under low vacuum and mild temperature conditions. The structure, microstructure, and chemical composition of the FePcCl NWs are thoroughly elucidated and compared with those of Fe(II) phthalocyanine NWs by a consistent and complementary combination of advanced electron microscopies and X-ray spectroscopies. In a further step, we vertically align the NWs by conformal deposition of a SiO2 shell. Such orientation is critical to analyze the magnetic properties of the FePcCl and FePc supported NWs. A ferromagnetic behavior below 30 K with an easy axis perpendicular to the phthalocyanine plane was observed in the two cases with the FePcCl nanowires presenting a wider hysteresis. These results open the path to the fabrication of nanostructured one-dimensional small-molecule spintronic devices., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In Vitro Comparative Study of Oxygen Plasma Treated Poly(Lactic–Co–Glycolic) (PLGA) Membranes and Supported Nanostructured Oxides for Guided Bone Regeneration Processes

  • Torres-Lagares, Daniel
  • Castellanos-Cosano, Lizett
  • Serrera-Figallo, María-Ángeles
  • López-Santos, Carmen
  • Barranco, Ángel
  • González-Elipe, Agustín R.
  • Gutiérrez-Pérez, José-Luis
(1) Background: The use of physical barriers to prevent the invasion of gingival and connective tissue cells into bone cavities during the healing process is called guided bone regeneration. The objective of this in-vitro study was to compare the growth of human osteoblasts on Poly(Lactic–co–Glycolic) (PLGA) membranes modified with oxygen plasma and Hydroxyapatite (HA), silicon dioxide (SiO2), and titanium dioxide (TiO2) composite nanoparticles, respectively. (2) Methods: All the membranes received a common treatment with oxygen plasma and were subsequently treated with HA nanostructured coatings (n = 10), SiO2 (n = 10) and TiO2 (n = 10), respectively and a PLGA control membrane (n = 10). The assays were performed using the human osteoblast line MG-63 acquired from the Center for Scientific Instrumentation (CIC) from the University of Granada. The cell adhesion and the viability of the osteoblasts were analyzed by means of light-field microphotographs of each condition with the inverted microscope Axio Observer A1 (Carl Zeiss). For the determination of the mitochondrial energy balance, the MitoProbe™ JC-1 Assay Kit was employed. For the determination of cell growth and the morphology of adherent osteoblasts, two techniques were employed: staining with phalloidin-TRITC and staining with DAPI. (3) Results: The modified membranes that show osteoblasts with a morphology more similar to the control osteoblasts follow the order: PLGA/PO2/HA > PLGA/PO2/SiO2 > PLGA/PO2/TiO2 > PLGA (p < 0.05). When analysing the cell viability, a higher percentage of viable cells bound to the membranes was observed as follows: PLGA/PO2/SiO2 > PLGA/PO2/HA > PLGA/PO2/TiO2 > PLGA (p < 0.05), with a better energy balance of the cells adhered to the membranes PLGA/PO2/HA and PLGA/PO2/SiO2. (4) Conclusion: The membrane in which osteoblasts show characteristics more similar to the control osteoblasts is the PLGA/PO2/HA, followed by the PLGA/PO2/SiO2., This study has been subsidised by the Consejería de Salud of the Junta de Andalucia through project PI-0047-2013: ‘Innovation in Nanomedicine: Guided Bone Regeneration with Nanofunctionalised Resorbable Membranes (Nanorog)’. The authors also thank the AEI (EU FEDER program Project MAT2016- 79866-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of irrigation conditions in the germination of plasma treated Nasturtium seeds

  • Molina, Ricardo
  • López-Santos, Carmen
  • Gómez-Ramírez, Ana
  • Vílchez, Alberto
  • Espinós, J.P.
  • González-Elipe, Agustín R.
Plasma treatments had emerged as a useful technique to improve seed germination. In this work we investigate the influence of different irrigation conditions and plasma treatments on the germination of nasturtium seeds. During plasma treatment, seeds experience a progressive weight loss as a function of treatment time that has been associated to water release, a process that is more pronounced after longer plasma treatment times. Seeds treated for short times (<30 s) are able to germinate more efficiently than untreated specimen under hydric stress (drought conditions), while plasma treatments for longer times (up to 300 s) impaired germination independently on irrigation conditions. Characterization analysis of plasma treated seeds by FTIR-ATR, SEM/EDX and XPS showed that plasma treatment affected the chemical state of pericarp while, simultaneously, induced a considerable increase in the seeds water uptake capacity. The decrease in germination efficiency found after plasma treatment for long times, or for short times under optimum irrigation conditions, has been attributed to that the excess of water accumulated in the pericarp hampers the diffusion up to the embryo of other agents like oxygen which are deemed essential for germination., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanoparticle formation and emission during laser ablation of ceramic tiles

  • Salmatonidis, Apostolos
  • Viana, Mar
  • Pérez, Noemí
  • Alastuey, Andrés
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Sanfélix, Vicenta
  • Monfort, Eliseo
Pulsed laser ablation (PLA) is a widely used technology, for surface structuring and tile decoration in the ceramic industry. During PLA, nanoparticles (NP <100 nm) are unintentionally released and may impact exposure. This work aims to understand the mechanisms controlling NP formation and release during ablation of different types of ceramic tiles, using different laser setups (near-IR and mid-IR). The measurements took place at laboratory and pilot-plant-scale, with varying laser wavelength, frequency, velocity, and pulse duration. In total, the combination of 4 types of ceramic tiles and 2 lasers was assessed. Particle number concentration and size distribution (SMPS with nano-DMA, DiSCmini, butanol-CPC) and particle mass concentration (DustTrak-DRX) were monitored. Samples were also collected for morphological and chemical characterization (TEM/EDX). High particle number concentrations were detected (3.5 *104/cm3 to 2.5 *106/cm3) for all of the tiles and under both laser setups. Particle formation (<10 nm) by nucleation was detected, and secondary amorphous SiO2 nanoparticles (>10 nm) were formed and released during ablation of the porcelain tiles. Different release mechanisms were identified: during ablation with the near-IR laser particles were emitted through melting and nucleation, while emissions from the mid-IR laser were attributed to melting and mechanical shockwaves. Particle number and mass emissions were dependent on the tile surface characteristics (e.g., porosity, crystallinity) and chemical properties. This work is potentially relevant from the point of view of exposure mitigation strategies in industrial facilities where PLA is carried out., The current work was carried out in the framework of the CERASAFE project (www.cerasafe.eu), with the support of SIINN ERA-NET (project id: 16), and is funded by the Spanish MINECO (PCIN-2015-173-C02-01). Partial support from project MAT2016-79866-R (AEI/FEDER, UE) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Laser‐induced coloration of ceramic tiles covered with magnetron sputtered precursor layers

  • Rico, Víctor J.
  • Lahoz, Ruth
  • Rey-García, F.
  • Francisco, I. de
  • Gil-Rostra, J.
  • Espinós, J.P.
  • Fuente, Germán F. de la
  • González-Elipe, Agustín R.
This paper reports a new methodology for the coloring of glazed ceramic tiles consisting of the near infrared pulsed laser processing of copper containing oxide coatings prepared by magnetron sputtering. As a second approach, the employ for the same purpose of a novel laser furnace technique is also described. Changing the laser parameters and using the laser furnace to treat the tiles at high temperature during irradiation has resulted in a wide color palette. The optical characterization of the modified tiles by UV‐Vis spectroscopy has been complemented with their microstructural and compositional analysis by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Time Of Flight Secondary Ion Mass Spectrometry (TOF‐SIMS). The chemical composition of the surface was obtained by X‐ray Photoemission Spectroscopy (XPS) and its structure determined by X?ray diffraction (XRD). The chemical resistance was characterized by several tests following the norm ISO 10545‐13. Color changes have been attributed to surface microstructural and chemical transformations that have been accounted for by simple models involving different ablation, melting, diffusion, and segregation/agglomeration phenomena depending on the laser treatments employed., Financial support from the EU (LIFE11/ENV/ES560), Innovaragón (ITA‐DGA/ES 1368), DGA (Group T87), and projects 201560E055, MAT2015‐69035‐REDC and MAT2016‐79866‐R from MINECO are gratefully acknowledged. F. Rey‐García acknowledges the Portuguese Science and Technology Foundation (FCT) for the Grant SFRH/BPD/108581/2015., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Metal films by laser ablation backwriting on glass

  • Angurel, Luis A.
  • Molina Mansilla, Ricardo
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Muñoz Rojas, David
  • Huerta, C. M. de la
  • Nguyen, V. H.
  • Fuente, Germán F. de la
Resumen del trabajo presentado a la Science and Applications of Thin Films, Conference & Exhibition; celebrada en Izmir (Turquia) del 17 al 21 de septiembre de 2018., The use of lasers to achieve transformations at interfaces, either on solids under air, controlled atmospheres or a diversity of liquid environments, is evolving at a fast pace and in-line with recent advances in photonic technologies. The singular properties of lasers, which provide a choice of emission parameters, such as emission wavelength, pulsed or cw mode and pulse width, together with the use of optomechanical means to scan in beam or line fashion, are ideal in order to trigger physico-chemical phenomena which are not available with alternative methods and are, at large, based on thermally activated processes. Recently developed methods in our Laboratories include those that are based, on the one hand, on strongly photothermal interactions; on the other, on mixed type interactions, where photothermal, photophysical and, in some cases, photochemical types may cohexist. In the former case, a solid may melt and, with the controled laser movement, directionally solidify into a material with controlled microstructure. In the latter case, an ablation process with extreme physical or chemical consequences may be triggered and be localised at the irradiated interface. A brief description of the phenomena behind laser-solid interactions will be presented, along with results obtained with the Laser Ablation Backwriting (LAB) method and applied to surface modification of glass. This has been recently developed in order to modify physico-chemical and functional properties of glass surfaces at large, based on this fully scaleable method. In particular, selective metallization of glass surfaces will be addressed in this talk., This research is partially supported by projects MAT2016-79866-R, ENE2017-83669-C4-1-R (Agencia Estatal de Investigación & Programa FEDER), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FETOPEN 801464)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Optical properties and electronic transitions of zinc oxide, ferric oxide, cerium oxide, and samarium oxide in the ultraviolet and extreme ultraviolet

  • Pauly, N.
  • Yubero, Francisco
  • Espinós, J.P.
  • Tougaard, S.
Optical properties and electronic transitions of four oxides, namely zinc oxide, ferric oxide, cerium oxide, and samarium oxide, are determined in the ultraviolet and extreme ultraviolet by reflection electron energy loss spectroscopy using primary electron energies in the range 0.3–2.0 keV. This technique allows the evaluation of the optical response in these ultraviolet spectral regions of a thin layer of material, and the analysis is straightforward. It is performed within the dielectric response theory by means of the QUEELS-(, )-REELS software developed by Tougaard and Yubero [Surf. Interface Anal. 36, 824 (2004) [CrossRef] ]. The method consists basically in the fitting of experimentally determined single-scattering electron energy loss cross sections with a parametric energy loss function of the corresponding material, to the one calculated within a dielectric response formalism. The obtained refractive index and extinction coefficients, as well as the identified electronic transitions are compared, when available, with previously published results., FY offers thanks for financial support from MAT2016-79866-R project (AEI/FEDER, UE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced green fluorescent protein in optofluidic Fabry-Perot microcavity to detect laser induced temperature changes in a bacterial culture

  • Lahoz, F.
  • Martín, I. R.
  • Walo, D.
  • Freire, R.
  • Gil-Rostra, J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
Thermal therapy using laser sources can be used in combination with other cancer therapies to eliminate tumors. However, high precision temperature control is required to avoid damage in healthy surrounding tissues. Therefore, in order to detect laser induced temperature changes, we have used the fluorescence signal of the enhanced Green Fluorescent Protein (eGFP) over-expressed in an E. coli bacterial culture. For that purpose, the bacteria expressing eGFP are injected in a Fabry-Perot (FP) optofluidic planar microcavity. In order to locally heat the bacterial culture, external infrared or ultraviolet lasers were used. Shifts in the wavelengths of the resonant FP modes are used to determine the temperature increase as a function of the heating laser pump power. Laser induced local temperature increments up to 6-7 °C were measured. These results show a relatively easy way to measure laser induced local temperature changes using a FP microcavity and using eGFP as a molecular probe instead of external nanoparticles, which could damage/alter the cell. Therefore, we believe that this approach can be of interest for the study of thermal effects in laser induced thermal therapies., This research was supported by Spanish Ministry of Economy and Competitiveness (Agencia Estatal de Investigación, AEI) and EU-FEDER (SAF2016-80626-R), (SAF2014-61644-EXP), (MAT2016-79866-R), (MAT2016-75586-C4-4-P).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Antibacterial Nanostructured Ti Coatings by Magnetron Sputtering: From Laboratory Scales to Industrial Reactors

  • Álvarez, Rafael
  • Muñoz-Piña, Sandra
  • González Sagardoy, María Ujué
  • Izquierdo-Barba, Isabel
  • Fernández-Martínez, Iván
  • Rico, Víctor J.
  • Arcos, Daniel
  • García-Valenzuela, Aurelio
  • Palmero, Alberto
  • Vallet-Regí, María
  • González-Elipe, Agustín R.
  • García-Martín, José Miguel
Based on an already tested laboratory procedure, a new magnetron sputtering methodology to simultaneously coat two-sides of large area implants (up to ~15 cm2) with Ti nanocolumns in industrial reactors has been developed. By analyzing the required growth conditions in a laboratory setup, a new geometry and methodology have been proposed and tested in a semi-industrial scale reactor. A bone plate (DePuy Synthes) and a pseudo-rectangular bone plate extracted from a patient were coated following the new methodology, obtaining that their osteoblast proliferation efficiency and antibacterial functionality were equivalent to the coatings grown in the laboratory reactor on small areas. In particular, two kinds of experiments were performed: Analysis of bacterial adhesion and biofilm formation, and osteoblasts–bacteria competitive in vitro growth scenarios. In all these cases, the coatings show an opposite behavior toward osteoblast and bacterial proliferation, demonstrating that the proposed methodology represents a valid approach for industrial production and practical application of nanostructured titanium coatings., The authors acknowledge the financial support from the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055, MAT2014-59772-C2-1-P, MAT2016-75611-R, and MAT2016-79866-R and network MAT2015-69035-REDC). The authors also thank the University of Seville (V and VI PPIT-US) and Fundación Domingo Martínez for financial support. M.V.-R. also thanks the European Research Council (advanced grant VERDI; ERC-2015-AdG proposal 694160). The authors thank the MiNa Laboratory at IMN funded by CM (S2018/NMT-4291 TEC2SPACE), MINECO (CSIC13-4E-1794), and the EU (FEDER, FSE) for the support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Impact of moisture on efficiency-determining electronic processes in perovskite solar cells

  • Salado, Manuel
  • Contreras-Bernal, Lidia
  • Calió, Laura
  • Todinova, Anna
  • López-Santos, Carmen
  • Ahmad, Shahzada
  • Borrás, Ana
  • Idígoras, Jesús
  • Anta, Juan A.
Moisture-induced degradation in perovskite solar cells was thoroughly investigated by structural (SEM, EDS, XRD and XPS) and device characterization (impedance and intensity modulated photocurrent spectroscopy) techniques. Both the influence of the perovskite composition and the nature of the hole selective material were analyzed. The degradation rate was found to be significantly slower for mixed perovskites and P3HT-based devices. However, for a fixed degradation degree (defined as a 50% drop from the initial photocurrent), all configurations show similar features in small-perturbation analysis. Thus, a new mid-frequency signal appears in the impedance response, which seems to be related to charge accumulation at the interfaces. In addition, faster recombination, with a more important surface contribution, and slower transport were clearly inferred from our results. Both features can be associated with the deterioration of the contacts and the formation of a higher number of grain boundaries., We thank Junta de Andalucía for financial support via grant FQM 1851 and FQM 2310. We thank the Ministerio de Economía y Competitividad of Spain (MAT2013-47192-C3-3-R and MAT2016-76892-C3-2-R) and the EU through the Cohesion Fund and FEDER programs (MAT2013-42900-P and MAT2016-79866-R) for financial support and Red de Excelencia “Emerging photovoltaic Technologies”. SA and LC are thankful for the “Thinface” project from the European Union Seventh Framework Programme, under grant agreement no. 607232, for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Formation of subsurface W5+ species in gasochromic Pt/WO3 thin films exposed to hydrogen

  • Castillero, Pedro
  • Rico, Víctor J.
  • López-Santos, Carmen
  • Barranco, Ángel
  • Pérez-Dieste, Virginia
  • Escudero, Carlos
  • Espinós, J.P.
  • González-Elipe, Agustín R.
M/WO3 (M = Pt, Pd) systems formed by a porous WO3 thin film decorated by metal nanoparticles are known for their reversible coloring upon exposure to H2 at room temperature. In this work, this gasochromic behavior is investigated in situ by means of near-ambient photoemission (NAPP). Pt/WO3 systems formed by very small Pt nanoparticles (10 ± 1 nm average size) incorporated in the pores of nanocolumnar WO3 thin films prepared by magnetron sputtering at an oblique angle have been exposed to a small pressure of hydrogen at ambient temperature. The recorded UV¿vis transmission spectra showed the reversible appearance of a very intense absorption band responsible for the blue coloration of these gasochromic films. In an equivalent experiment carried out in the NAPP spectrometer, W 4f, O 1s, Pt 4f, and valence band photoemission spectra have been recorded at various photon energies to follow the evolution of the reduced tungsten species and hydroxyl groups formed upon film exposure to hydrogen. The obtained results are compared with those of a conventional X-ray photoemission study after hydrogen exposure between 298 and 573 K. As investigated by NAPP, the gasochromic behavior at 298 K is accounted for by a reaction scheme in which hydrogen atoms resulting from the dissociation of H2 onto the Pt nanoparticles are spilt over to the WO3 substrate where they form surface OH¿/H2O species and subsurface W5+ cations preferentially located in buried layers of the oxide network., The authors thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (Projects MAT2013-40852-R, 201560E055, and MAT2016-79866-R)) for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A compact and portable optofluidic device for detection of liquid properties and label-free sensing

  • Lahoz, F.
  • Martín, I. R.
  • Walo, D.
  • Gil-Rostra, J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
Optofluidic lasers have been widely investigated over the last few years mainly because they can be easily integrated in sensor devices. However, high power pulse lasers are required as excitation sources, which, in practice, limit the portability of the system. Trying to overcome some of these limitations, in this paper we propose the combined use of a small CW laser with a Fabry-Perot optofluidic planar microcavity showing high sensitivity and versatility for detection of liquid properties and label-free sensing. Firstly, a fluorescein solution in ethanol is used to demonstrate the high performances of the FP microcavity as a temperature sensor both in the laser (high pump power above laser threshold) and in the fluorescence (low pump power) regimes. A shift in the wavelength of the resonan cavity modes is used to detect changes in the temperature and our results show that high sensitivities could be already obtained using cheap and portable CW diode lasers. In the second part of the paper, the demonstration of this portable device for label-free sensing is illustrated under low CW pumping. The wavelength positions of the optofluidic resonant modes are used to detect glucose concentrations in water solutions using a protein labelled with a fluorescent dye as the active medium., This research was supported by European Regional Development Funds program (EU-FEDER), Agencia Estatal de Investigación (AEI) and MINECO (SAF2014-61644-EXP), (MAT2013-40852-R), (MAT2013-46649-C4-4-P), (MAT2015-71070-REDC), (MAT2016-79866-R), (MAT2016-75586-C4-4-P), FUNCOAT (CSD2008-00023), and by the Junta de Andalucía (projects P12-FQM-2265 and P10-FQM-6900).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Structural control in porous/compact multilayer systems grown by magnetron sputtering

  • García-Valenzuela, Aurelio
  • López-Santos, Carmen
  • Álvarez, Rafael
  • Rico, Víctor J.
  • Cotrino, José
  • González-Elipe, Agustín R.
  • Palmero, Alberto
In this work we analyze a phenomenon that takes place when growing magnetron sputtered porous/compact multilayer systems by alternating the oblique angle and the classical configuration geometries. We show that the compact layers develop numerous fissures rooted in the porous structures of the film below, in a phenomenon that amplifies when increasing the number of stacked layers. We demonstrate that these fissures emerge during growth due to the high roughness of the porous layers and the coarsening of a discontinuous interfacial region. To minimize this phenomenon, we have grown thin interlayers between porous and compact films under the impingement of energetic plasma ions, responsible for smoothing out the interfaces and inhibiting the formation of structural fissures. This method has been tested in practical situations for compact TiO/porous SiO multilayer systems, although it can be extrapolated to other materials and conditions., Authors acknowledge the University of Seville (VPPI-US), the Junta de Andalucía (TEP8067, TEP5283 and P12–2265MO) and the Ministry of Economy and Competitiveness of Spain (MAT2013-42900-P, MAT2013-40852-R, MAT2016-79866-R, MAT2015-69035-REDC) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Micron-scale wedge thin films prepared by plasma enhanced chemical vapor deposition

  • López-Santos, Carmen
  • Álvarez, Rafael
  • Palmero, Alberto
  • Borrás, Ana
  • Casquel del Campo, Rafael
  • Holgado, Miguel
  • González-Elipe, Agustín R.
Wedge-shaped materials are currently employed for optical analyses and sensing applications. In this paper, we present an easy to implement plasma enhanced chemical vapor deposition procedure to grow wedge-shaped thin films with controlled slope at the scale of few hundred microns. The method relies on the use of few tenths micron height obstacles to alter the laminar flow of precursor gas during deposition and is applied for the fabrication of wedge-shaped ZnO thin films. Local interference patterns, refractive index, and birefringence of the films have been measured with one micron resolution using a specially designed optical set-up. Their micro- and nano-structures have been characterized by means of scanning electron microscopy and theoretically reproduced by Monte Carlo calculations., We acknowledge the support of the University of Seville (VPPI‐US), the European Development Funds program (EU‐FEDER), and the Spanish Ministry of Economy and Competitiveness and Agencial Estatal de Investigación (AEI) (projects MAT2013‐40852‐R, MAT2016‐79866‐R, MAT2015‐69035‐R, 201560E055, and MAT2015‐69035‐REDC).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dye giant absorption and light confinement effects in porous bragg microcavities

  • Oliva-Ramírez, Manuel
  • Gil-Rostra, J.
  • Simonsen, Adam C.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
This work presents a simple experimental procedure to probe light confinement effects in photonic structures. Two types of porous 1D Bragg microcavities with two resonant peaks in the reflection gap were prepared by physical vapor deposition at oblique angle configurations and then infiltrated with dye solutions of increasing concentrations. The unusual position shift and intensity drop of the transmitted resonant peak observed when it was scanned through the dye absorption band have been accounted for by the effect of the light trapped at their optical defect layer. An experimentally observed giant absorption of the dye molecules and a strong anomalous dispersion in the refractive index of the solution are claimed as the reasons for the observed variations in the Bragg microcavity resonant feature. Determining the giant absorption of infiltrated dye solutions is proposed as a general and simple methodology to experimentally assess light trapping effects in porous photonic structures., The authors thank the European Regional Development Funds Program (EU-FEDER) and the MINECO-AEI (Projects MAT2013-40852-R, 201560E055, and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The role of surface recombination on the performance of perovskite solar cells: effect of morphology and crystalline phase of TiO2 contact

  • Idígoras, Jesús
  • Contreras-Bernal, Lidia
  • Cave, James M.
  • Courtier, Nicola E.
  • Barranco, Ángel
  • Borrás, Ana
  • Sánchez-Valencia, J. R.
  • Anta, Juan A.
  • Walker, Alison B.
Herein, the preparation of 1D TiO nanocolumnar films grown by plasma-enhanced chemical vapor deposition is reported as the electron selective layer (ESL) for perovskite solar devices. The impact of the ESL architecture (1D and 3D morphologies) and the nanocrystalline phase (anatase and amorphous) is analyzed. For anatase structures, similar power conversion efficiencies are achieved using an ESL either the 1D nanocolumns or the classical 3D nanoparticle film. However, lower power conversion efficiencies and different optoelectronic properties are found for perovskite devices based on amorphous 1D films. The use of amorphous TiO as electron selective contact produces a bump in the reverse scan of the current–voltage curve as well as an additional electronic signal, detected by impedance spectroscopy measurements. The dependence of this additional signal on the optical excitation wavelength used in the IS experiments suggests that it stems from an interfacial process. Calculations using a drift-diffusion model which explicitly considers the selective contacts reproduces qualitatively the main features observed experimentally. These results demonstrate that for a solar cell in which the contact is working properly the open-circuit photovoltage is mainly determined by bulk recombination, whereas the introduction of a “bad contact” shifts the balance to surface recombination., The authors thank Junta de Andalucía for financial support via grant FQM 1851 and FQM 2310. The authors thank Ministerio de Economía y Competitividad of Spain and Agencia Estatal de Investigación (AEI) and EU (FEDER) under grants MAT2013‐47192‐C3‐3‐R, MAT2016‐76892‐C3‐2‐R, MAT2016‐79866‐R and Red de Excelencia “Emerging photovoltaic Technologies” for financial support. J.R.S.‐V. and A.B. acknowledge Marie Skłodowska‐Curie ActionsH2020‐MSCA‐IF‐2014 PlasmaPerovSol grant (Project ID 661480) and the University of Seville through the VI PPIT‐US. J.M.C. and N.E.C. were supported by EPSRC funded studentships from the CDT in New and Sustainable Photovoltaics (reference EP/L01551X/1). A.B.W. was supported by the Energy oriented Centre of Excellence (EoCoE), Horizon2020 grant research number 676629.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nickel/Copper bilayer-modified screen printed electrode for glucose determination in flow injection analysis

  • Salazar, Pedro
  • Rico, Víctor J.
  • González-Elipe, Agustín R.
This work reports about the performance of a Ni/Cu-modified screen printed electrodes (SPE/Ni/Cu), prepared by physical vapor deposition (PVD) in an oblique angle configuration (OAD), for non-enzymatic glucose sensing applications. SPE/Ni/Cu electrodes showed an excellent reversibility and a catalytic behavior for detection of glucose that were controlled by the diffusion of reactants up to the active sites at the electrode surface. The study with a flow injection analysis (FIA) setup of the main experimental variables affecting the detection process has shown that the developed electrode system had an excellent glucose sensitivity of 1.04 AM1cm2 (R2:0.999), a linear response up to 1 mM, a limit of detection of 0.33 mM and a time of analysis of ca. 30 s per sample. The selectivity of the sensor was checked against various interferences, including ascorbic acid, uric acid, acetaminophen and other sugars, in all cases with excellent results. The feasibility of using this sensor for practical applications was successfully confirmed by determining the glucose concentration in different commercial beverages., The financial support for the development of this work has been granted by the FEDER funds of the UE and the projects MAT2013‐40852‐R and MAT2016‐79866‐R from MINECO, 201560E055 from CSIC‐MINECO and RECUPERA2020 from MINECO‐“Fondo social Europeo”. Pedro Salazar thanks RECUPERA 2020 project for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sensing and biosensing with screen printed electrodes modified with nanostructured nickel oxide thin films prepared by magnetron sputtering at oblique angles

  • Salazar, Pedro
  • García-García, Francisco J.
  • González-Elipe, Agustín R.
This work reports about the sensing and biosensing applications of a novel screen printed electrode (SPE) modified by nanostructured nickel oxide thin films obtained by reactive magnetron sputtering under an oblique angle configuration. Using these films as electrodes we demonstrate their ability to detect hydrogen peroxide under neutral pH conditions. Furthermore, as a proof-of-concept, NiO-modified SPEs have been developed and their cholesterol biosensing properties determined by cyclic voltammetry and chronoamperometry., The support of projects RECUPERA 2020, from MINECO and the “Fondo social Europeo”, IPT-2012-0961-300000, 201560E055, MAT2016-79866-R and network MAT2015-69035-REDC are gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In situ monitoring of the phenomenon of electrochemical promotion of catalysis

  • Espinós, J.P.
  • Rico, Víctor J.
  • González-Cobos, J.
  • Sánchez-Valencia, J. R.
  • Pérez-Dieste, Virginia
  • Escudero, C.
  • de Lucas-Consuegra, A.
  • González-Elipe, Agustín R.
In this work we investigate by in-situ near-ambient pressure photoemission (NAPP) spectroscopy the phenomenon of Electrochemical Promotion of Catalysis (EPOC). We studied the reduction and diffusion kinetics of alkaline ions in a solid electrolyte cell formed by a nickel electrode supported on K-β-alumina electrolyte. Experiments in ultra-high vacuum and in the presence of steam showed that the amount of potassium atoms supplied to the surface is probably affected by nickel electronic modifications induced by adsorbed OH groups. It was also deduced that part of the segregated potassium would be adsorbed at inner interfaces where it would be inaccessible to the photoelectron analyzer. A migration mechanism of the promoter is proposed consisting in: (i) the electrochemical reduction of the alkali ions (potassium) at the Ni/solid electrolyte/gas interface; (ii) the spillover of potassium atoms onto the Ni gas-exposed surface; and (iii) the diffusion of potassium atoms to Ni inner grain boundary interfaces., The authors thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (Projects MAT2013-40852-R, 201560E055 and MAT2016-79866-R) for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Colorimetric energy sensitive scintillator detectors based on luminescent multilayer designs

  • Ferrer, F. J.
  • Gil-Rostra, J.
  • González-Elipe, Agustín R.
  • Yubero, Francisco
In this work we present a new concept for energy sensitive radiation-beam scintillator detectors based on a luminescent multilayer design, where each layer within the stack consists of a rare-earth-doped highly transparent oxide. For a given type of particle beam (i.e., protons, α particles, etc.), its penetration depth, and therefore its energy loss at a particular buried layer, depends on its initial kinetic energy. Relying on this principle and since the intensity of the luminescent response of each layer and substrate should be proportional to the energy deposited by the radiation beam, we prove that a characteristic energy dependent color emission is obtained depending on both the phosphors integrated in the luminescent stack and on the primary energy and type of particle beam. Phosphor doping, emission efficiency, layer thickness, and multilayer structure design are key parameters to achieve a broad gamut in colorimetric response. The developed scintillators are designed to operate in a transmission geometry (light detection from the opposite side of the incident radiation) which is well suited for high energy particle detection in fields such as oncotherapy, space radiation, or of fusion studies. The principles of the method are illustrated with a case example typical of ion beam accelerators devoted to materials analysis. It is obtained that the kinetic energy of protons/alpha particle beams can be distinguished and evaluated with a sensitivity of 0.06/0.25 chromaticity units per MeV in the 0.7–2.0 MeV range., We thank Spanish Ministry of Economy, Industry and Competitiveness (AEI-FEDER project MAT2016-79866-R, CSIC (201560E055) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Quantitative analysis of Yb 4d photoelectron spectrum of metallic Yb

  • Pauly, N.
  • Yubero, Francisco
  • Tougaard, S.
The measured Yb 4d3/2 intensity is larger than the Yb 4d5/2 in X‐ray photoelectron (XPS) emission of metallic Yb, which is unexpected. The shape and intensity of photoelectron peaks are strongly affected by extrinsic excitations due to electron transport out of the surface (including bulk and surface effects) and to intrinsic excitations due to the sudden creation of the static core hole. To quantitatively extract from experimental XPS the primary excitation spectrum (ie, the initial excitation process) of the considered transition, these effects must be included within the theoretical description. The combined effect of both extrinsic and intrinsic excitations can be described by an effective energy‐differential inelastic electron scattering cross section for XPS evaluated by a dielectric response model with the dielectric function as only input. Then, using this cross section, a direct evaluation of the primary excitation spectrum is performed by standard peak shape analysis for thick homogeneous samples. We use this approach in the present paper to determine the Yb 4d photoemission spectrum for metallic Yb. We show that the unexpected larger intensity of Yb 4d3/2 compared to 4d5/2 can be fully accounted for by our model and that the total spectrum consists of a sum of symmetric primary excitation peaks., F.Y. thanks financial support from MAT2016‐79866‐R project (AEI/FEDER, UE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Kinetic energy-induced growth regimes of nanocolumnar Ti thin films deposited by evaporation and magnetron sputtering

  • Álvarez, Rafael
  • García-Valenzuela, Aurelio
  • Rico, Víctor J.
  • García-Martín, José Miguel
  • Cotrino, José
  • González-Elipe, Agustín R.
  • Palmero, Alberto
We experimentally analyze different growth regimes of Ti thin films associated to the existence of kinetic energy-induced relaxation mechanisms in the material's network when operating at oblique geometries. For this purpose, we have deposited different films by evaporation and magnetron sputtering under similar geometrical arrangements and at low temperatures. With the help of a well-established growth model we have found three different growth regimes: (i) low energy deposition, exemplified by the evaporation technique, carried out by species with typical energies in the thermal range, where the morphology and density of the film can be explained by solely considering surface shadowing processes, (ii) magnetron sputtering under weak plasma conditions, where the film growth is mediated by surface shadowing mechanisms and kinetic-energy-induced relaxation processes, and (iii) magnetron sputtering under intense plasma conditions, where the film growth is highly influenced by the plasma, and whose morphology is defined by nanocolumns with similar tilt than evaporated films, but with much higher density. The existence of these three regimes explains the variety of morphologies of nanocolumnar Ti thin films grown at oblique angles under similar conditions in the literature., The authors thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055, MAT2014-59772-C2-1-P, and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support. The authors also acknowledge the financial support of the University of Seville (V and VI PPIT-US). The National Center for Accelerators (Seville, Spain) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

2D compositional self-patterning in magnetron sputtered thin films

  • García-Valenzuela, Aurelio
  • Álvarez, Rafael
  • Rico, Víctor J.
  • Espinós, J.P.
  • López-Santos, Carmen
  • Solís Céspedes, Javier
  • Siegel, Jan
  • Campo, Ángel Adolfo del
  • Palmero, Alberto
  • González-Elipe, Agustín R.
7 pags., 5 figs., Unlike topography patterning, widely used for numerous applications and produced by means of different technologies, there are no simple procedures to achieve surface compositional patterning at nanometric scales. In this work we have developed a simple method for 2D patterning the composition of thin films. The method relies on the magnetron sputtering deposition at oblique angles onto patterned substrates made by laser induced periodic surface structures (LIPSS). The method feasibility has been demonstrated by depositing SiOx thin films onto LIPSS structures generated in Cr layers. A heterogeneous and aligned distribution of O/Si ratios (and different Sin+ chemical states) along the LIPSS structure in length scales of some hundreds nm's has been proven by angle resolved X-ray photoelectron spectroscopy and a patterned arrangement of composition monitored by atomic force microscopy-Raman analysis. The obtained results are explained by the predictions of a Monte Carlo simulation of this deposition process and open the way for the tailored one-step fabrication of surface devices with patterned compositions., The authors thank the European Regional Development Fund program (EU-FEDER) and the MINEICO-AEI (201560E055, MAT2016-79866-R, TEC2017-82464-R projects and network MAT2015-69035-REDC) for financial support. We also acknowledge the support of the University of Seville (V and VI PPIT-US).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydrophobicity, freezing delay, and morphology of laser-treated aluminum surfaces

  • Rico, Víctor J.
  • López-Santos, Carmen
  • Villagrá, Martín
  • Espinós, J.P.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Borrás, Ana
  • González-Elipe, Agustín R.
Until recently, superhydrophobicity was considered as a hint to predict surface icephobicity, an association of concepts that is by no means universal and that has been proven to depend on different experimental factors and material properties, including the actual morphology and chemical state of surfaces. This work presents a systematic study of the wetting and freezing properties of aluminum Al6061, a common material widely used in aviation, after being subjected to nanosecond pulsed IR laser treatments to modify its surface roughness and morphology. All treated samples, independent of their surface finishing state, presented initially an unstable hydrophilic wetting behavior that naturally evolved with time to reach hydrophobicity or even superhydrophobicity. To stabilize the surface state and to bestow the samples with a permanent and stable hydrophobic character, laser-treated surfaces were covered with a thin layer of CFx prepared by plasma-enhanced chemical vapor deposition. A systematic comparison between freezing delay (FD) and wetting properties of water droplets onto these plasma-/polymer-modified laser-treated surfaces that, under conditions where a heterogeneous nucleation mechanism prevails, surface morphology rather than the actual value of the surface roughness parameter the key feature for long FD times. In particular, it is found that surface morphologies rendering a Cassie–Baxter wetting regime longer FDs than those characterized by a Wenzel-like wetting state. It is that laser treatment, with or without additional coverage with thin CFx coatings, affects wetting and ice formation behaviors and might be an efficient procedure to mitigate icing problems on metal surfaces., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055 and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Influence of crystallographic texture and external electromagnetic fields on sub-ns pulsed UV laser derived nanostructures

  • Porta-Velilla, L.
  • Cubero, A.
  • Castro, Miguel
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
Resumen del trabajo presentado al European Congress and Exhibition on Advanced Materials and Processes (EUROMAT), celebrado en Estocolmo (Suecia) del 1 al 5 de septiembre de 2019., [Introduction/Purpose]: Generation of Laser-induced Periodic Surface Structures (LIPSS) is a general phenomenon that has been observed in a broad range of materials and intensively studied since the commercial availability of ultra-short pulsed lasers. It has been observed that the morphology of LIPSS can be controlled by the selection of adequate laser processing parameters., [Methods]: In this work, we have analysed the generation of LIPSS in different metal surfaces using a sub-ns (300 ps) pulsed UV laser, with a laser-line scanning configuration. In addition to the laser parameters, different variables that can modify how LIPSS are generated, have been explored. EBSD studies have been used to determine the crystallographic direction of each grain at the surface of the material and how it modifies the characteristics of nanostructure generation. Experiments have also been performed under different electromagnetic fields during laser processing., [Results]: It has been observed that crystallographic orientation of grains has a significant influence on the generation of nanostructures. When prominent cones are generated, they appear only in some grains with a given orientation, for instance, (001) planes in stainless steel. In the case of ripples, period, size and orientation are also modified. For some configurations of external electromagnetic fields, the uniformity of the nanostructure can also be improved in extended areas., [Conclusions]: It is well established that nature and ordering of LIPSS nanostructures depend on the laser parameters, mainly irradiance and polarization, and on the material. In this work, it has been determined that for a given material, this order can be modified depending on the crystallographic orientation of each particular grain and using adequate external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Metal surface nanostructures developed with sub-ns UV laser line scanning under different atmospheres

  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Rojo, J. A.
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado al International Symposium Fundamentals of Laser Assisted Micro- & Nanotechnologies (FLAMN), celebrado en San Petersburgo (Rusia) del 30 de junio al 4 de julio de 2019., Work financed by MAT2016-79866-R & ENE2017-83669-C4-1-R (MINECO-AEI-FEDER, UE), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) and Aragón Government (Research Group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced stability of perovskite solar cells incorporating dopant-free Crystalline spiro-OMeTAD layers by vacuum sublimation

  • Barranco, Ángel
  • López-Santos, Carmen
  • Idígoras, Jesús
  • Aparicio, Francisco J.
  • Obrero-Pérez, José M.
  • López-Flores, Víctor
  • Contreras-Bernal, Lidia
  • Rico, Víctor J.
  • Ferrer, F. J.
  • Espinós, J.P.
  • Borrás, Ana
  • Anta, Juan A.
  • Sánchez-Valencia, J. R.
The main handicap still hindering the eventual exploitation of organometal halide perovskite-based solar cells is their poor stability under prolonged illumination, ambient conditions, and increased temperatures. This article shows for the first time the vacuum processing of the most widely used solid-state hole conductor (SSHC), i.e., the Spiro-OMeTAD [2,2′,7,7′-tetrakis (N,N-di-p-methoxyphenyl-amine) 9,9′-spirobifluorene], and how its dopant-free crystalline formation unprecedently improves perovskite solar cell (PSC) stability under continuous illumination by about two orders of magnitude with respect to the solution-processed reference and after annealing in air up to 200 °C. It is demonstrated that the control over the temperature of the samples during the vacuum deposition enhances the crystallinity of the SSHC, obtaining a preferential orientation along the π–π stacking direction. These results may represent a milestone toward the full vacuum processing of hybrid organic halide PSCs as well as light-emitting diodes, with promising impacts on the development of durable devices. The microstructure, purity, and crystallinity of the vacuum sublimated Spiro-OMeTAD layers are fully elucidated by applying an unparalleled set of complementary characterization techniques, including scanning electron microscopy, X-ray diffraction, grazing-incidence small-angle X-ray scattering and grazing-incidence wide-angle X-ray scattering, X-ray photoelectron spectroscopy, and Rutherford backscattering spectroscopy., The authors thank the “Agencia Estatal de Investigación”, “Consejería de Economía y Conocimiento de la Junta de Andalucía” (US‐1263142), “Ministerio de Economía y Competitividad” (MAT2016‐79866‐R, MAT2013‐42900‐P, FPA2016‐77689‐C2‐1‐R, and MAT2016‐76892‐C3‐2‐R) and the European Union (EU) through cohesion fund and FEDER 2014‐2020 programs for financial support. J.R.S.‐V. and A.B. acknowledge the EU project PlasmaPerovSol and funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska‐Curie grant agreement ID 661480. J.R.S.‐V‐ and M.C.L.‐S. thank the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US” (VI PPIT‐US). This research has received funding from the EU‐H2020 research and innovation programme under Grant Agreement No. 654360 having benefitted from the access provided by Technische Universität Graz at Elettra—TUG in Trieste (IT) within the framework on the NFFA (Nanoscience Foundries & Fine Analysis) Europe Transnational Access Activity. F.J.A. and J.R.S.‐V. acknowledge the “Juan de la Cierva” and “Ramon y Cajal” national programs, respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Liquid switchable radial polarization converters made of sculptured thin films

  • Oliva-Ramírez, Manuel
  • Rico, Víctor J.
  • Gil-Rostra, J.
  • Bertrán, Enric
  • Serna, Rosalía
  • González-Elipe, Agustín R.
  • Yubero, Francisco
7 pags., 6 figs., 1 app., A radial polarization converter is a super-structured optical retarder that converts a conventional linearly polarized light beam into a structured beam with radial or azimuthal polarization. We present a new type of these sophisticated optical elements, which is made of porous nanostructured sculptured single thin films or multilayers prepared by physical vapor deposition at an oblique angle. They are bestowed with an axisymmetric retardation activity (with the fast axis in a radial configuration). In particular, a Bragg microcavity multilayer that exhibits a tunable transmission peak in the visible range with a retardance of up to 0.35 rad has been fabricated using this methodology. Owing to the highly porous structure of this type of thin films and multilayers, their retardance could be switched off by liquid infiltration. These results prove the possibility of developing wavelength dependent (through multilayer optical design) and switchable (through vapor condensation or liquid infiltration within the pore structure) radial polarization converters by means of oblique angle physical vapor deposition., We acknowledge the support of the European Regional Development Funds program (EU-FEDER), the Spanish MinistryEconomy, Industry, and Competitiveness (projects 201560E055,MAT2016-79866-R, RECUPERA 2020 and Red CONSOLIDER MAT2015-69035-REDC).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Laser induced high temperature surface chemistry

  • Rey-García, F.
  • Rico, Víctor J.
  • Bao-Varela, C.
  • Angurel, Luis A.
  • González-Elipe, Agustín R.
  • Fuente, Germán F. de la
Resumen del póster presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Ceramic tiles are widely used as construction materials because of their outstanding mechanical properties (high strength, hardness, toughness and abrasion resistance), chemical inertness and aesthetic appearance. Concomitantly, a variety of new functionalities have been demonstrated during recent years, by developing appropriate frit and glaze compositions. Laser processing has been intensively utilized to improve surface characteristics, either applying ablative laser regimes or intense mid-IR emission beams that enable high temperature surface melting. In this context, in addition to the numerous thermal annealing procedures reported in the literature and applied to industry to modify the surface properties of ceramics, a novel Laser Furnace (LF) method has been recently patented. It enables modifying the surface finish of solids by inducing high temperature (1500-3000 °C) reactions at surfaces and interfaces, while maintaining volume temperatures at relatively low values (i.e. below 1200 °C). This paper deals with the application of this laser technology to the coloring of ceramic tiles previously deposited with either metal and oxide precursor thin films, or, alternatively with noble metal-organic layers. These layer/tile systems have been treated both, with nIR ns pulsed lasers and by cw CO2 lasers with emission in the mid-IR. The latter were coupled into a roller furnace to induce chemical processes which result in a variety of coloring effects., The authors gratefully acknowledge funding from MICINN and AEI (ENE2017-83669-C4-1-R and MAT2016-79866-R), FEDER/EU (project SPRINT (EU H2020-FET-OPEN/0426)) and Gobierno de Aragón (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Laser line scanning for large area surface microstructure control

  • Santos, H.
  • Angurel, Luis A.
  • Trujillo, F. J.
  • Muñoz Rojas, David
  • Masse, C.
  • Nguyen, V. H.
  • Bea, J. A.
  • Fuente, Germán F. de la
Resumen del póster presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Large-scale industrial materials must comply with crucial requirements beyond their technical specifications. The overall economy of any material system designed is a priority, leading to a complex equilibrium between costs and performance. Ultimate feasibility assessments rely on materials design efforts, particularly in processes exposed to extreme corrosive environments as well as those with high quality requirements in terms of interfacial defects in multilayer devices. In such systems surface engineering plays a key role, offering the means to maximize the life span of a certain material system. In parallel to the intrinsic cost savings derived in terms of maintenance, certain techniques allow an extreme control of the processing conditions, resulting in lower consumption of reactants, time and energy. This is the case of laser surface processing, particularly regarding laser line scanning (LLS). Such technique combines the transverse movement of a target with the fixed scanning linear movement of the laser spot along the axis perpendicular to the probe’s displacement. This technique has been applied to well-studied systems as Fe-Al protective coatings, rendering useful development paths to improve the alloying performance addressing subjects as: grain microstructure orientation, stoichiometric gradients smothering, segregation dispersion or interface defects density. The present work takes into account the above considerations, in an attempt to adapt this novel Laser Line Scanning method to process functional metal oxide coatings. With the help of standard simulation models, attempts to densify coated surfaces, as well as to control microstructure, will be described., The authors gratefully acknowledge the financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades, Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU (project SPRINT (EU H2020-FETOPEN/0426), PHOBIC2ICE (EU GA 690819)), and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Generation of nanostructures in metallic surfaces using subnanosecond UV laser processing

  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado a la International Conference on Condensed Matter and Materials Science (ICCMMS), celebrada en Adana (Turquia) del 14 al 19 de octubre de 2019., In this work we present the rich surface structure phenomenology that has been observed when the surface of different metals (Nb, Ni, steel) is irradiated with a subnanosecond (300 ps) UV laser, and how it affects some of their properties. The influence of different laser parameters, as the laser polarization direction, the pulse irradiance, laser scanning speed and the overlapping in the perpendicular direction, have been studied and a complete set of nanostructures have been defined. Laser treatments have been performed in air, but also in controlled atmospheres (Ar, N2) or with the surface immersed in liquids (Vaseline oil, water) observing that the generated nanostructures are different depending on the particular experimental conditions imposed. An important effort has been carried out in order to obtain homogeneous nanostructures over extended areas, using a new laser line scanning protocol. In these studies, it has been observed that not only the laser parameters affect the generated nanostructure, but some materials properties are also important. Combining laser treatments with EBSD studies it has been demonstrated that crystallography also plays an important role in the generated nanostructure, observing that the level of interaction of the laser with a particular grain has some correlation with its crystallographic order. It has ben also observed that, in depending on the properties of the materials, nanostructures can be modified by the application of external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, Bekir
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrel, C. J.
  • Sáez-Puche, R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles., The authors acknowledge financial support from MINECO-AEI-FEDER, EU (projects MAT2016-79866-R and ENE2017-83669-C4-1-R) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Physicochemical surface analysis and germination at different irrigation conditions of DBD plasma‐treated wheat seeds

  • Molina Mansilla, Ricardo
  • Lalueza, Alba
  • López-Santos, Carmen
  • Ghobeira, Rouba
  • Cools, Pieter
  • Morent, Rino
  • de Geyter, Nathalie
  • González-Elipe, Agustín R.
Plasma treatment is increasingly being explored as an effective presowing treatment improving seed germination. This study examines the synergetic effect of the irrigation condition and the physicochemical surface properties of wheat seeds subjected to atmospheric dielectric barrier discharge plasma activation on their water uptake and germination. Extensive surface analysis revealed a remarkably enhanced wettability of plasma‐treated seeds due to the insertion of oxygen‐containing functionalities on their surface. However, long plasma exposures damaged the outermost layers of the pericarp due to a pronounced oxidative etching effect. Although the seed germination capacity was not affected by the plasma treatments, short plasma exposures were shown to enhance water uptake and accelerate seed germination, especially under water‐scarcity conditions., The authors would like to thank the contribution of the scanning electron microscopy service of the Institute of Marine Sciences (ICM‐CSIC). The authors also thank EU‐FEDER funds and the MINECO (projects MAT2016–79866‐R, MINECO‐CSIC 201860E050) and Junta de Andalucía (project P12–2265 MO). Rouba Ghobeira would also like to thank the Research Foundation Flanders (FWO‐grant number 12ZC720N) for financing her post‐doctoral position., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Unravelling discharge and surface mechanisms in plasma assisted ammonia reactions

  • Navascués, Paula
  • Obrero-Pérez, José M.
  • Cotrino, José
  • González-Elipe, Agustín R.
  • Gómez-Ramírez, Ana
Current studies on ammonia synthesis by means of atmospheric pressure plasmas respond to the urgent need of developing less environmentally aggressive processes than the conventional Haber–Bosch catalytic reaction. Herein, we systematically study the plasma synthesis of ammonia and the much less investigated reverse reaction (decomposition of ammonia into nitrogen and hydrogen). Besides analyzing the efficiency of both processes in a packed-bed plasma reactor, we apply an isotope-exchange approach (using D2 instead of H2) to study the reaction mechanisms. Isotope labeling has been rarely applied to investigate atmospheric plasma reactions, and we demonstrate that this methodology may provide unique information about intermediate reactions that, consuming energy and diminishing the process efficiency, do not effectively contribute to the overall synthesis/decomposition of ammonia. In addition, the same methodology has demonstrated the active participation of the interelectrode material surface in the plasma-activated synthesis/decomposition of ammonia. These results about the involvement of surface reactions in packed-bed plasma processes, complemented with data obtained by optical emission spectroscopy analysis of the plasma phase, have evidenced the occurrence of inefficient intermediate reaction mechanisms that limit the efficiency and shown that the rate-limiting step for the ammonia synthesis and decomposition reactions are the formation of NH* species in the plasma phase and the electron impact dissociation of the molecule, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina Mansilla, Ricardo
  • Ertuğrul, M.
  • Navarro, Rafael
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laserinduced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces., This paper is dedicated to the memory of Prof. Rafael Navarro. The authors gratefully acknowledge the financial support from Spanish MINECO-AEI and EU FEDER Program (projects ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU project SPRINT (H2020-FETOPEN 801464) and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI and the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Setting a comprehensive strategy to face the runback icing phenomena

  • Mora, J.
  • López García, Paloma
  • Carreño, F.
  • González, M.
  • Gutiérrez, M.
  • Montes, L.
  • Gavira, V. R.
  • López-Santos, Carmen
  • Vicente, A.
  • Rivero, P.
  • Rodríguez, R.
  • Larumbe, S.
  • Acosta, C.
  • Ibáñez-Ibáñez, P.
  • Corozzi, A.
  • Raimondo, M,
  • Kozera, R,
  • Przybyszewski, B,
  • González-Elipe, Agustín R.
  • Borrás, Ana
  • Redondo, F,
  • Agüero, A,
The development of anti-icing robust surfaces is a hot topic nowadays and particularly crucial in the aeronautics or wind energy sectors as ice accretion can compromise safety and power generation efficiency. However, the current performance of most anti-icing strategies has been proven insufficient for such demanding applications, particularly in large unprotected zones, which located downstream from thermally protected areas, may undergo secondary icing. Herein, a new testing methodology is proposed to evaluate accretion mechanisms and secondary icing phenomena through, respectively, direct impact and running-wet processes and systematically applied to anti-icing materials including commercial solutions and the latest trends in the state-of-the-art. Five categories of materials (hard, elastomeric, polymeric matrix, SLIPS and superhydrophobic) with up to fifteen formulations have been tested. This Round-Robin approach provides a deeper understanding of anti-icing mechanisms revealing the strengths and weaknesses of each material. The conclusion is that there is no single passive solution for anti-ice protection. Thus, to effectively protect a given real component, different tailored materials fitted for each particular zone of the system are required. For this selection, shape analysis of such a component and the impact characteristics of water droplets under real conditions are needed as schematically illustrated for aeronautic turbines., The project leading to this article has received funding from the EU H2020 program under grant agreement 899352 (FETOPEN-01-2018-2019-2020 - SOUNDofICE). The authors also thank the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00 and PID2019-110430GB-C21) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe”, to RTI2018-096262-B-C44–MAITAI, Multidisciplinary Approach for the Implementation of New Technologies to prevent Accretion of Ice on aircraft, funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia, Innovación y Universidades—Retos) and CSIC 202160E002-217538, for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US”(VI PPIT-US) and the Ramon y Cajal Grant program., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser-induced coloration of ceramic tiles covered with magnetron sputtered precursor layers

  • Rico, V.J.
  • Lahoz, R.
  • Rey-García, F.
  • de Francisco, I.
  • Gil-Rostra, J.
  • Espinós, J.P.
  • de la Fuente, G.F.
  • González-Elipe, A.R.
This paper reports a new methodology for the coloring of glazed ceramic tiles consisting of the near infrared pulsed laser processing of copper containing oxide coatings prepared by magnetron sputtering. As a second approach, the employ for the same purpose of a novel laser furnace technique is also described. Changing the laser parameters and using the laser furnace to treat the tiles at high temperature during irradiation has resulted in a wide color palette. The optical characterization of the modified tiles by UV-Vis spectroscopy has been complemented with their microstructural and compositional analysis by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Time Of Flight Secondary Ion Mass Spectrometry (TOF-SIMS). The chemical composition of the surface was obtained by X-ray Photoemission Spectroscopy (XPS) and its structure determined by X?ray diffraction (XRD). The chemical resistance was characterized by several tests following the norm ISO 10545-13. Color changes have been attributed to surface microstructural and chemical transformations that have been accounted for by simple models involving different ablation, melting, diffusion, and segregation/agglomeration phenomena depending on the laser treatments employed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, B.
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrell, C.J.
  • Sáez-Puche, R.
  • de la Fuente, G.F.
  • Angurel, L.A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina R.
  • Ertugrul M.
  • Larrea Á.
  • Navarro R.
  • Rico V.
  • Yubero F.
  • González-Elipe A.R.
  • Fuente G.F. de la
  • Angurel L.A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laser-induced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces.
Docta Complutense
Publication Artículo científico (JournalArticle)

Wetting and spreading of liquid lithium onto nanocolumnar tungsten coatings tailored through the topography of stainless steel substrates

  • Alcalá Penadés, Germán
  • Muñoz-Piña, S.
  • Garcia-Valenzuela, A.
  • Oyarzabal, E.
  • Gil-Rostra, J.
  • Rico, V.
  • Alvarez, R.
  • Tabares, F.L.
  • Palmero, A.
  • Gonzalez-Elipe, A.R.
The use of liquid metal as an alternative to cover the plasma-exposed areas of fusion reactors has called for the development of substrates where refilling and metal spreading occur readily and at reasonably low temperatures. In the search for common materials for this purpose, we show that nanostructured tungsten coatings deposited on stainless steel (SS) by magnetron sputtering at oblique angles (MS-OAD) is a good option, provided that the surface microstructure of substrate is properly engineered. Tungsten thin films with nominal thicknesses of 500 and 2500 nm were deposited onto SS plates subjected to conventional surface finishing treatments (sand blasting, sand paper abrasion and electrochemical polishing) to modify the surface topography and induce the appearance of different groove patterns. In the first part of this work we show how the topographical features of the SS substrates affect the typical nanocolumnar microstructure of OAD thin films of tungsten. Subsequently, we characterize the spreading behavior of liquid lithium onto these tungsten nanocolumnar surfaces and critically discuss whether nanocolumnar tungsten thin films are a suitable option for the wetting and spreading of molten lithium. As a result, we reveal that the features of the tungsten nanocolumnar coating, characterized by a given height and void spaces between nanocolumns in the order of 1–2 μm, is critical for the spreading of molten lithium, while the existence of wider channels affects it very weakly. Moreover, it is shown that tungsten films deposited by MS-OAD on SS substrates subjected to conventional finishing procedures represent a good alternative to other more complex surface engineering procedures utilized for this purpose.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

In situ determination of the water condensation mechanisms on superhydrophobic and superhydrophilic titanium dioxide nanotubes

  • Macias-Montero, Manuel|||0000-0002-5508-928X
  • Lopez-Santos, Carmen
  • Filippin, A. Nicolas
  • Rico, Victor J.|||0000-0002-5083-0390
  • Espinos, Juan Pedro|||0000-0002-3053-0841
  • Fraxedas, Jordi|||0000-0002-2821-4831
  • Pérez-Dieste, Virginia
  • Escudero, Carlos|||0000-0001-8716-9391
  • Gonzalez-Elipe, Agustín|||0000-0002-6417-1437
  • Borras, Ana|||0000-0001-8799-2054
One-dimensional (1D) nanostructured surfaces based on high-density arrays of nanowires and nanotubes of photoactive titanium dioxide (TiO) present a tunable wetting behavior from superhydrophobic to superhydrophilic states. These situations are depicted in a reversible way by simply irradiating with ultraviolet light (superhydrophobic to superhydrophilic) and storage in dark. In this article, we combine in situ environmental scanning electron microscopy (ESEM) and near ambient pressure photoemission analysis (NAPP) to understand this transition. These experiments reveal complementary information at microscopic and atomic level reflecting the surface wettability and chemical state modifications experienced by these 1D surfaces upon irradiation. We pay special attention to the role of the water condensation mechanisms and try to elucidate the relationship between apparent water contact angles of sessile drops under ambient conditions at the macroscale with the formation of droplets by water condensation at low temperature and increasing humidity on the nanotubes' surfaces. Thus, for the as-grown nanotubes, we reveal a metastable and superhydrophobic Cassie state for sessile drops that tunes toward water dropwise condensation at the microscale compatible with a partial hydrophobic Wenzel state. For the UV-irradiated surfaces, a filmwise wetting behavior is observed for both condensed water and sessile droplets. NAPP analyses show a hydroxyl accumulation on the as-grown nanotubes surfaces during the exposure to water condensation conditions, whereas the water filmwise condensation on a previously hydroxyl enriched surface is proved for the superhydrophilic counterpart.