Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 28
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Surface superconductivity changes of niobium sheets by femtosecond laser-induced periodic nanostructures

  • Cubero, Á.
  • Martínez, E.
  • Angurel, L.A.
  • de la Fuente, G.F.
  • Navarro, R.
  • Legall, H.
  • Krüger, J.
  • Bonse, J.
Irradiation with ultra-short (femtosecond) laser beams enables the generation of sub-wavelength laser-induced periodic surface structures (LIPSS) over large areas with controlled spatial periodicity, orientation, and depths affecting only a material layer on the sub-micrometer scale. This study reports on how fs-laser irradiation of commercially available Nb foil samples affects their superconducting behavior. DC magnetization and AC susceptibility measurements at cryogenic temperatures and with magnetic fields of different amplitude and orientation are thus analyzed and reported. This study pays special attention to the surface superconducting layer that persists above the upper critical magnetic field strength Hc2, and disappears at a higher nucleation field strength Hc3 . Characteristic changes were distinguished between the surface properties of the laser-irradiated samples, as compared to the corresponding reference samples (non-irradiated). Clear correlations have been observed between the surface nanostructures and the nucleation field Hc3, which depends on the relative orientation of the magnetic field and the surface patterns developed by the laser irradiation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser floating zone growth: Overview, singular materials, broad applications, and future perspectives

  • Rey-García, F.
  • Ibáñez, R.
  • Angurel, L.A.
  • Costa, F.M.
  • Fuente, G.F.
The Laser Floating Zone (LFZ) technique, also known as Laser-Heated Pedestal Growth (LHPG), has been developed throughout the last several decades as a simple, fast, and crucible-free method for growing high-crystalline-quality materials, particularly when compared to the more conventional Verneuil, Bridgman-Stockbarger, and Czochralski methods. Multiple worldwide efforts have, over the years, enabled the growth of highly oriented polycrystalline and single-crystal highmelting materials. This work attempted to critically review the most representative advancements in LFZ apparatus and experimental parameters that enable the growth of high-quality polycrystalline materials and single crystals, along with the most commonly produced materials and their relevant physical properties. Emphasis will be given to materials for photonics and optics, as well as for electrical applications, particularly superconducting and thermoelectric materials, and to the growth of metastable phases. Concomitantly, an analysis was carried out on how LFZ may contribute to further understanding equilibrium vs. non-equilibrium phase selectivity, as well as its potential to achieve or contribute to future developments in the growth of crystals for emerging applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Exploring the high-temperature electrical performance of Ca3-xLaxCo4O9 thermoelectric ceramics for moderate and low substitution levels

  • Constantinescu G.
  • Rasekh S.
  • Amirkhizi P.
  • Lopes D.V.
  • Vieira M.A.
  • Kovalevsky A.V.
  • Diez J.C.
  • Sotelo Mieg A.E.
  • Madre Sediles, M.A.
  • Torres Portero, M.A.
Aliovalent substitutions in Ca3Co4O9 often result in complex effects on the electrical properties and the solubility, and impact of the substituting cation also depends largely on the preparation and processing method. It is also well-known that the monoclinic symmetry of this material’s composite crystal structure allows for a significant hole transfer from the rock salt-type Ca2CoO3 buffer layers to the hexagonal CoO2 ones, increasing the concentration of holes and breaking the electron-hole symmetry from the latter layers. This work explored the relevant effects of relatively low La-for-Ca substitutions, for samples prepared and processed through a conventional ceramic route, chosen for its simplicity. The obtained results show that the actual substitution level does not exceed 0.03 (x < 0.03) in Ca3-xLaxCo4O9 samples with x = 0.01, 0.03, 0.05 and 0.07 and that further introduction of lanthanum results in simultaneous Ca3Co4O9 phase decomposition and secondary Ca3Co2O6 and (La, Ca)CoO3 phase formation. The microstructural effects promoted by this phase evolution have a moderate influence on the electronic transport. The electrical measurements and determined average oxidation state of cobalt at room temperature suggest that the present La substitutions might only have a minor effect on the concentration of charge carriers and/or their mobility. The electrical resistivity values of the Ca3-xLaxCo4O9 samples with x = 0.01, 0.03 and 0.05 were found to be ~1.3 times (or 24%) lower (considering mean values) than those measured for the pristine Ca3Co4O9 samples, while the changes in Seebeck coefficient values were only moderate. The highest power factor value calculated for Ca2.99La0.01Co4O9 (~0.28 mW/K2m at 800 °C) is among the best found in the literature for similar materials. The obtained results suggest that low rare-earth substitutions in the rock salt-type layers can be a promising pathway in designing and improving these p-type thermoelectric oxides, provided by the strong interplay between the mobility of charge carriers and their concentration, capable of breaking the electron-hole symmetry from the conductive layers. © 2021 by the authors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Drastic microstructural modification of Bi2Ca2Co2Oy ceramics by Na doping and laser texturing

  • Özçelik, C.
  • Depci, T.
  • Gürsul, M.
  • Çetin, G.
  • Özçelik, B.
  • Torres, M.A.
  • Madre, M.A.
  • Sotelo, A.
Bi2Ca2-xNaxCo2Oy materials with x = 0 = x = 0.125, have been prepared either by sintering through the classical ceramic method, or textured using the laser floating zone technique. XRD results have shown that Bi2Ca2Co2Oy phase is the major one, independently of the Na content, in both kind of samples. SEM studies have shown a drastic microstructural modification between sintered and laser-textured materials. Na-doping increases density and grain sizes in sintered materials, while it enhances grain alignment in laser-grown materials. Moreover, it decreases secondary phase content in all cases. Electrical resistivity is also drastically reduced through texturing, when compared to the sintered samples, and Na-doping further decreases it. The lowest values determined in the laser-textured samples (26 mO cm at 650 °C) are around 40% lower than the best in sintered materials. On the other hand, S has been only slightly affected for Na-doping or processing method for all samples. Consequently, the highest power factor at 650 °C (0.18 mW/K2 m) has been obtained in laser-grown 0.075Na-doped samples, which is around 20 and 70% higher than the measured in undoped laser-textured samples, and sintered ones, respectively. Se han preparado materiales de composición Bi2Ca2-xNaxCo2Oy, con x = 0 ≤ x ≤ 0,125, por el método de estado sólido, además de texturarlos mediante la técnica de zona flotante inducida por láser. Los resultados de XRD han mostrado que la fase Bi2Ca2Co2Oy aparece como la mayoriraria, independientemente del contenido de Na, en ambos tipos de muestras. Los estudios SEM han encontrado una drástica modificación microestructural entre materiales sinterizados y texturados. El dopado con Na aumenta la densidad y el tamaño de grano en materiales sinterizados, mientras que mejora la orientación de los granos en materiales texturados. Además, disminuye el contenido de fases secundarias en todos los casos. La resistividad eléctrica disminuye drásticamente con el texturado, en comparación con las muestras sinterizadas, mientras que el dopado con Na la disminuye aún más. Los valores más bajos determinados en muestras texturadas (26 mΩ cm a 650 °C) son alrededor del 40% menor que los mejores datos publicados en materiales sinterizados. Por otro lado, S solo se ha visto afectado levemente, tanto por el dopado como por el método de procesado. En consecuencia, el máximo factor de potencia a 650 °C (0,18 mW/K2 m) se ha obtenido en muestras dopadas con 0,075 Na y texturadas, que es alrededor de un 20 a un 70% superior al medido en muestras texturadas sin dopar y sinterizadas, respectivamente.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Large enhancement of thermal conductance at ambient and cryogenic temperatures by laser remelting of plasma-sprayed Al2O3 coatings on Cu

  • Cubero, Á.
  • Martínez, E.
  • de la Fuente, G.F.
  • García Cano, I.
  • Dosta, S.
  • Angurel Lambán, L.A.
Joints of high thermal contact conductance and electrical insulation have been obtained by coating copper supports with thin alumina (Al2O3) layers (of 140–150 µm thickness). This has been achieved by a combination of plasma spraying process and the subsequent coating remelting by a near-Infrared (n-IR) laser. With a proper optimization of the laser processing conditions, it is possible to transform the metastable ¿-Al2O3 phase of the as-sprayed coatings to stable a-Al2O3, and to achieve denser alumina coatings. This results in a large enhancement of the thermal conductance of the joints, enabling their application as heat sinks at cryogenic and ambient temperatures. The process proposed in this work is scalable for the formation of alumina coatings on large metallic pieces of complex geometries. © 2021
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Sub-ns-pulsed laser cleaning of an archaeological bone from the Sierra de Atapuerca, Spain: a case study

  • Rahman, M.A.
  • de la Fuente, G.F.
  • Carretero, J.M.
  • Maingi, E.M.
  • Alonso Abad, M.P.
  • Alonso Alcalde, R.
  • Chapoulie, R.
  • Schiavon, N.
  • Angurel, L.A.
Controlled laser irradiation parameters using recently developed sub-nanosecond pulsed laser technology with emission wavelength in the near Infrared regime (1064 nm) have been assessed on a Pleistocene bone from the archaeological site of Sierra de Atapuerca, Spain. Burst pulse mode was employed to explore contaminant removal efficiency, while at the same time, assessing the degree of damage produced to the underlying original substrate surface. The surface morphology and composition of the deteriorated bone have been characterized, along with the effects of laser irradiation at 1064 nm, using Optical Microscopy (OM), Scanning Electron Microscopy-with Energy Dispersive X-ray Spectrometry (SEM-EDS), and X-ray Photoelectron Spectroscopy (XPS). The most effective laser cleaning parameters in burst mode have been identified in order to optimize the emission parameters of the laser, thus localizing its interaction within the outermost layers of contaminants and degradation products, avoiding damage to the underlying original bone surface. Hence, threshold cleaning and substrate damage values have been determined for this new sub-ns laser, paving the way to safer laser cleaning procedures that may be useful for the effective conservation of bone archaeological artifacts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Evaluation of pressure and temperature effect on the structure and properties of Ca2.93Sr0.07Co4O9 ceramic materials

  • Torres M.A.
  • Madre M.A.
  • Dura O.J.
  • García G.
  • Marinel S.
  • Martinez-Filgueira P.
  • Sotelo A.
In this work, the effect of hot-pressing conditions on the performances of Sr-doped Ca3Co4O9 materials has been investigated. The samples were prepared from attrition milled precursors, which reduced the processing time. Samples were hot-pressed at temperatures (T) between 800 and 900 °C and pressures (P) from 51 to 71 MPa. The out-of-plane X-ray diffraction (XRD) showed that all samples are formed by the thermoelectric phase, with a good grain orientation which is improved with T, and P, as demonstrated by their Lotgering factor. The observations through Scanning Electron Microscopy (SEM) have revealed that grain sizes and orientation are enhanced with T, and P, as well as density through Archimedes''s method. All these trends are reflected in the flexural strength and microhardness. The electrical resistivity is lower when the T, or P, is increased, reaching 6.4 mO cm for samples processed at 900 °C and 71 MPa, which is about the best reported values in the literature. On the other hand, contrarily to the expected results, they also showed the highest S values, 182 µV/K, which are similar to the best reported values for highly dense textured materials. Thermal conductivity values do not follow a regular evolution with the hot-pressing conditions, probably due to internal stresses, reaching the lowest values at 800 °C in samples processed at 800 °C and 51 MPa (1.51 W/(K*m)) or 900 °C and 61 MPa (1.53 W/(K*m)). Consequently, the highest ZT values have been determined in samples processed at 900 °C and 61 MPa (0.35) which is higher than the best reported values in literature for bulk textured samples, to the best of our knowledge. © 2021 The Authors
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Significant enhancement of superconducting performances of Bi-2212 fibers through combined sodium substitution and LFZ process

  • Gürsul, M.
  • Ergin, I.
  • Özçelik, C.
  • Depci, T.
  • Özçelik, B.
  • Madre, M.A.
  • Sotelo, A.
This paper reports the microstructure, magnetoresistivity, electrical and superconducting properties of Bi-2212 fibers with Na+ ions incorporated into a superconducting matrix prepared by a polymer solution method and additionally textured through the laser floating zone process. XRD patterns showed that Bi-2212 phase is the major one with mostly (00l) diffractions due to the grain alignment, independently of Na content. SEM micrographs showed that samples are composed of well-stacked and oriented grains. The irreversibility field (Hirr), upper critical magnetic field (Hc2), coherence length (¿), and activation energies (U) have been calculated using magnetoresistivity measurements and explained based on the thermally activated flux flow (TAFF) model. Considering the resistivity-temperature graph for zero field, Tc values tend to increase from 84.8 K (for the pure sample) to 93.2 K (for 0.075Na sample), slightly decreasing for higher content. Besides, transition temperature width (¿Tc = Tconset - Tcoffset) decreases with the increment in the Na content and reaches its minimum value (¿Tc = 3.7 K) in 0.075Na sample. However, broadening of superconducting transition has been observed with applied field and Tc values decreased to 76.1 K for the pure sample and 86.8 K for 0.075Na sample. Likewise, the activation energies of the samples also decreases significantly with the increase of the magnetic field and the activation energies of the Na-containing samples are found to be higher than the pure sample at each magnetic field value. Hc2(0) values are calculated as 33.8, 43.8, 50.1, 33.1, and 21.4 T for 0.0, 0.075, 0.10, and 0.20 T Na samples, respectively. As a consequence, referring to all experimental results and theoretical findings, the superconducting characteristics improve regularly with Na-doping until x = 0.075 due to increment in the interaction of superconducting clusters, decrement in weak-links and stabilization of charge carriers in CuO2 conducting planes. © 2021, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning thermoelectric properties of Bi2Ca2Co2Oy through K doping and laser floating zone processing

  • Özçelik, C.
  • Depci, T.
  • Gürsul, M.
  • Çetin, G.
  • Özçelik, B.
  • Torres, M.A.
  • Madre, M.A.
  • Sotelo, A.
In the present study, thermoelectric Bi2Ca2-xKxCo2Oy ceramic materials (x = 0.0, 0.05, 0.075, 0.10, and 0.125) in different forms (called bulk, as-grown and annealed fibers) have been manufactured via a classical solid-state method and textured using the laser floating zone (LFZ) technique. The identification and characteristics of undoped and doped samples were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD patterns of all samples have shown great similarity, and the major peaks can be assigned to the Bi2Sr2Co2Oy thermoelectric phase, independently of the processing technique and K-doping. SEM-EDS have indicated the randomly oriented plate like grains of different sizes in bulk sample, evolving to longer and well-oriented grain structure through K-doping and LFZ. Because of the incongruent melting properties of compound, the high number of secondary phases formed in the as-grown samples. In order to reduce it, an annealing and K-doping process have been applied. The microstructural evolution is reflected on the electrical properties, and the lowest resistivity values are found in the annealed K-doped fibers. Seebeck coefficient is positive in all cases, pointing out to p-type conduction mechanism. These modifications led to PF values up to 0.162 mW/(K2m), obtained in 0.10 K-doped annealed fibers at 650 °C. © 2021 Elsevier Masson SAS
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Highly regular hexagonally-arranged nanostructures on Ni-W alloy tapes upon irradiation with ultrashort UV laser pulses

  • Porta-Velilla, Luis
  • Turan, Neslihan
  • Cubero, Alvaro
  • Shao, Wei
  • Li, Hongtao
  • Fuente, German F. de la
  • Martinez, Elena
  • Larrea, Angel
  • Castro, Miguel
  • Koralay, Haluk
  • Cavdar, Sukru
  • Bonse, Joern
  • Angurel, Luis A.
Nickel tungsten alloy tapes (Ni-5 at% W, 10 mm wide, 80 mu m thick, biaxially textured) used in second-generation high temperature superconductor (2G-HTS) technology were laser-processed in air with ultraviolet ps-laser pulses (355 nm wavelength, 300 ps pulse duration, 250-800 kHz pulse repetition frequency). By employing optimized surface scan-processing strategies, various laser-generated periodic surface structures were generated on the tapes. Particularly, distinct surface microstructures and nanostructures were formed. These included sub-wavelength-sized highly-regular hexagonally-arranged nano-protrusions, wavelength-sized line-grating-like laser-induced periodic surface structures (LIPSS, ripples), and larger irregular pyramidal microstructures. The induced surface morphology was characterized in depth by electron-based techniques, including scanning electron microscopy (SEM), electron back scatter diffraction (EBSD), cross-sectional transmission electron microscopy (STEM/TEM) and energy dispersive X-ray spectrometry (EDS). The in-depth EBSD crystallographic analyses indicated a significant impact of the material initial grain orientation on the type of surface nanostructure and microstructure formed upon laser irradiation. Special emphasis was laid on high-resolution material analysis of the hexagonally-arranged nano-protrusions. Their formation mechanism is discussed on the basis of the interplay between electromagnetic scattering effects followed by hydrodynamic matter re-organization after the laser exposure. The temperature stability of the hexagonally-arranged nano-protrusion was explored in post-irradiation thermal annealing experiments, in order to qualify their suitability in 2G-HTS fabrication technology with initial steps deposition temperatures in the range of 773-873 K.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Comparison of in-situ oxidation behavior of Zr by micro-arc oxidation and selective laser melting

  • Shao, Wei
  • Liu, Cancan
  • Wu, Qiaojun
  • Li, Hongtao
  • Angurel, L.A.
  • de la Fuente, G.F.
  • Jiang, Bailing
Al2O3-ZrO2 ceramic coatings were prepared on 6061 Al alloy by Micro Arc Oxidation (MAO) and Selective Laser Melting (SLM). Coatings prepared by MAO exhibit a porous structure and a progressive oxidation of the substrate as a function of processing time. Those made by SLM are denser, although the presence of cracks is observed throughout their surface. XRD results suggest that the ceramic coating consists of m-ZrO2, t-ZrO2 and γ-Al2O3 phases for the MAO process, while a Zr3O phase is also present in SLM. The hardness of the MAO Al2O3-ZrO2 coating is higher than that obtained by SLM. Young’s modulus of the MAO coating is lower, due to higher level of porosity observed in the coating prepared by MAO. Moreover, in-situ oxidation, heating and solidification processes are all discussed and compared within the context of MAO and SLM peculiarities. The processes and transformation mechanisms involved in the processing methods produce diverse microstructures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Impact of silver addition on the superconducting performances of Bi2Sr2Ca0.925Na0.075Cu2Oy:Ag composite fibers

  • Atilla, B.
  • Ergin, I.
  • Gürsul, M.
  • Özçelik, B.
  • Madre, M.A.
  • Sotelo, A.
This work studies the impact of metallic Ag addition on the microstructural, electrical, superconducting, and magnetic properties of Bi2Sr2Ca0.925Na0.075Cu2Oy. Samples with 0, 1, 3, 5 wt% were prepared from precursors produced by sol-gel method, followed by texturing through the laser floating zone (LFZ) technique. The normal state and residual resistivity values decrease with Ag addition up to 3 wt% (from 7.61 to 2.54, and from 1.85 to 0.25 mΩ.cm, respectively), reflecting the reduction of porosity and the improvement of grains alignment and connectivity. Irreversibility line (IL) shifts towards high temperature with the introduction of Ag, confirming the higher grains connectivity in Ag-containing samples. Moreover, the increase of Hirr (from 28.9 to 43.1 T), Hc2 (from 64.6 to 85.9 T), and Jc (from 4104 to 1.2105 A/cm2) values with Ag addition also point out to the improvement of grains connectivity and flux pinning energies induced by Ag addition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Use of green fs lasers to generate a superhydrophobic behavior in the surface of wind turbine blades

  • Rivera-Sahún, Joaquín
  • Porta-Velilla, Luis
  • de la Fuente, Germán F.
  • Angurel, Luis A.
Ice generation on the surface of wind generator blades can affect the performance of the generator in several aspects. It can deteriorate sensor performance, reduce efficiency, and cause mechanical failures. One of the alternatives to minimize these effects is to include passive solutions based on the modification of the blade surfaces, and in particular to generate superhydrophobic behavior. Ultra-short laser systems enable improved micromachining of polymer surfaces by reducing the heat affected zone (HAZ) and improving the quality of the final surface topography. In this study, a green fs laser is used to micromachine different patterns on the surface of materials with the same structure that can be found in turbine blades. Convenient optimization of surface topography via fs laser micromachining enables the transformation of an initially hydrophilic surface into a superhydrophobic one. Thus, an initial surface finish with a contact angle ca. 69° is transformed via laser treatment into one with contact angle values above 170°. In addition, it is observed that the performance of the surface is maintained or even improved with time. These results open the possibility of using lasers to control turbine blade surface microstructure while avoiding the use of additional chemical coatings. This can be used as a complementary passive treatment to avoid ice formation in these large structures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Anomalous grain growth in sintered Bi2Ca2Co2-xCuxOy + Ag ceramic composites by Cu doping

  • Amaveda, H.
  • Madre, M. A.
  • Mora, M.
  • Torres, M. A.
  • Sotelo, A.
Bi2Ca2Co2 − xCuxOy + 4 wt%Ag (with x between 0 and 0.20) thermoelectric materials were prepared through a sol-gel method via nitrates. Powder XRD patterns showed the presence of thermoelectric phase as the major one, accompanied by metallic silver. SEM observations identified three different secondary phases in the samples, together with an exaggerated grain growth with Cu doping. The microstructural modifications are reflected in an important decrease of electrical resistivity, ∼ 3% when compared to undoped samples, due to the reduction on the number of grain boundaries, and the increase of Co4+ in the conducting layer. The minimum values at 650 ºC were obtained in 0.10 Cu-doped samples, 69 mΩ cm, which are lower than the reported in sintered samples. On the other hand, Seebeck coefficient was only slightly affected and reached the highest values at 650 ºC in 0.15 Cu-doped samples, 215 µV/K, which is practically the same measured in undoped ones, 211 µV/K, and lower than those reported for sintered samples. Consequently, the highest PF at 650 ºC has been determined in 0.10 Cu-doped samples, which is around 50% higher than the obtained in samples prepared through the classical solid-state method, or the undoped ones prepared in this work.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ultrashort pulsed Femtosecond UV laser for selective cleaning of significant Cretaceous flints

  • Rahman, Md. Ashiqur
  • Fuente Leis, Germán Francisco de la
  • Carretero, José Miguel
  • Alonso Abad, Mª Pilar
  • Ruiz Navazo, Marta
  • Alonso Alcalde, Rodrigo
  • Chapoulie, Rémy
  • Schiavon, Nick
  • Angurel, Luis A.
This work reports on studies aimed to evaluate the utilization of ultrashort 238 fs (fs) pulsed UV laser emission at 343 nm for eliminating colored crusts and surface deposits on significant Cretaceous flint surfaces, in an attempt to safeguard its aesthetic appearance and archaeological value. The results indicate that fs UV lasers may be an ideal, non-contact tool for selective surface cleaning of sensitive archaeological artefacts, since they enable contaminant desorption while avoiding photothermal damage.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Chemical and laser cleaning of corrosion encrustations on historical stained glass: a comparative study

  • Maingi, E. M.
  • Alonso, M. P.
  • Angurel, L. A.
  • de la Fuente, G. F.
  • Dubernet, S.
  • Chapoulie, R.
  • Mellouët, O.
  • Vally, E.
The aim of this research work was to conduct a comparative study on the effectiveness of the application of chemical cleaning versus laser cleaning in the removal of surface congruent dissolution products from a potash-lime–silica historical stained-glass sample. EDTA was selected as the chemical cleaning agent. Laser cleaning was performed using a 238 fs pulse UV (343 nm) laser. The comparative cleaning studies were carried out on a stained-glass piece supplied by the Maison Lorin Glass Restoration Workshop from Chartres, France. Given the complex nature, irregular thickness and heterogeneity of the encrustations found on the glass, the two cleaning approaches were carefully performed step by step, while monitoring the process using an optical microscope. Raman spectroscopy and field emission scanning electron microscopy were used to characterize the changes induced on the sample surface during the cleaning process. The results demonstrate that the two cleaning approaches were able to eliminate the outer surface dark layer associated with carbon compounds, as well as the external part of the white layer generated by the crystallization of salts, formed with the dissolved elements after a reaction with the air. A comparison of the advantages and disadvantages of each method is also presented.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

UV femtosecond laser cleaning of encrusted historical stained-glasses

  • Maingi, E. M.
  • Alonso, M. P.
  • Fuente, Germán F. de la
  • Dubernet, S.
  • Lefrais, Y.
  • Chapoulie, R.
  • Vally, E.
  • Angurel, L. A.
Laser irradiation enables the removal of unwanted surface deposits from different materials in a safe and controllable manner. Laser parameters should be carefully selected to achieve the removal of the target contaminants without inducing damage to the substrate. Ultra-short pulse lasers have opened new opportunities for safe and controlled decontamination of cultural heritage materials because the thickness of material that is affected by the laser is limited. In this study, an ultraviolet femtosecond pulsed laser was used for the removal of unwanted encrustation formed on the surface of an historical colourless stained-glass sample from the Cuenca Cathedral in Spain. One of the sides of this glass exhibits a reddish-brown grisaille that also has to be preserved. A laser cleaning process has been designed to avoid heat accumulation while controlling the thickness of ablated material. In this context, a multi-step process was selected in order to be able to eliminate, in a controlled way, the crust layer without damaging the grisaille layer, or the glass substrate. In this case, laser irradiation in beam scanning mode with a pulse repetition frequency of 10 kHz proved to be effective for the safe cleaning of the glass. The latter was analysed before and after laser cleaning by optical and confocal microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray fluorescence, and Raman spectroscopy, confirming that the crust layer was effectively eliminated without damaging the surface.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ultra-Short Pulse Laser Cleaning of Contaminated Pleistocene Bone: A Comprehensive Study on the Influence of Pulse Duration and Wavelength

  • Rahman, Md. Ashiqur
  • de la Fuente, Germán F.
  • Miguel Carretero, José
  • Abad, Mª Pilar Alonso
  • Alcalde, Rodrigo Alonso
  • Chapoulie, Rémy
  • Schiavon, Nick
  • Angurel, Luis A.
The impact of wavelength and pulse duration in laser cleaning of hard blackish contaminants crust from archaeologically significant Pleistocene bone is investigated in this research. The objective is to determine the practical cleaning procedures and identify adequate laser parameters for cleaning archaeological bone from Sima de los Huesos (Spain) based on conservation and restoration perspectives. Bone surface cleaning was performed utilizing two Q-switched Nd:YAG lasers: sub-nanosecond pulsed lasers with emission wavelengths at 355 nm and 1064 nm, respectively, and a Yb:KGW femtosecond pulsed laser with an emission wavelength in the third harmonic at 343 nm. In all experiments, the laser beam scanning mode was applied to measure cleaning efficiency in removing contaminants and degradation products while assessing the underlying substrate surface damage. Several properties, including wavelength-dependent absorption, pulse repetition rate, and thermal properties of the material, are analyzed when evaluating the ability of these lasers to boost the cleaning efficiency of the deteriorated bone surface. Bone surface morphology and composition were studied and compared before and after laser irradiation, using Optical Microscopy, Scanning Electron Microscopy with Energy Dispersive X-ray Spectrometry (SEM-EDS), Fourier Transform Infrared Spectroscopy (FTIR), and X-ray Photoelectron Spectroscopy (XPS) characterization methods. The results indicate that 238-femtosecond UV laser irradiation with 2.37 TWcm−2 is significantly safer and more efficient toward surface contaminant desorption than sub-nanosecond laser irradiation. The results herein presented suggest that these types of fs lasers may be considered for realistic laser conservation of valuable historic and archaeological museum artifacts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Variation of mechanical and electrical performances of Bi2Ca2Co1.7Ox ceramics above working conditions

  • Rasekh, S.
  • Ghanbari, M.
  • Natoli, A.
  • Torres, M. A.
  • Madre, M. A.
  • Sotelo, A.
This work explores the effect of exposing the Bi2Ca2Co1.7Ox-textured ceramics at temperatures above working conditions, on mechanical and electrical properties. Microstructural studies have shown a first improvement of microstructure with an important grain growth, followed by the formation of porosity and the appearance of cracks for larger times. These features were reflected on their mechanical and electrical properties. Three point bending tests have revealed an increase of bending strength with the thermal treatment, reaching the maximum at 24 h and decreasing for further treatment time, which is very slight for times larger than 196 h. On the other hand, electrical resistivity is drastically reduced with the thermal treatment when compared to the as-grown samples. Moreover, the samples behavior is modified from semiconducting-like for as-grown samples to metallic-like for the thermally treated ones. Accordingly, Seebeck coefficient is decreased with the thermal treatment, being very similar for all thermally treated samples. As a consequence of the drastic decrease of electrical resistivity, although with lower reduction on the Seebeck coefficient, all thermally treated samples display higher power factor values than the as-grown ones. The highest values at 650 °C (0.29 mW/K2 m) have been obtained in textured samples thermally treated for 48 h, which are comparable to the best values reported in the literature without the use of expensive materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Detailed low temperature studies on thermoelectric performance of K-doped Bi2Ca2Co2Oy ceramics fibers

  • Özçelik, C.
  • Depci, T.
  • Çetin, G.
  • Gürsul, M.
  • Özçelik, B.
  • Madre, M. A.
  • Sotelo, A.
  • Ando, H.
  • Terashima, K.
  • Takano, Y.
The effect of K substitution for Ca in Bi2Ca2-xKxCo2Oy (x = 0.0, 0.05, 0.075, 0.10, and 0.125) thermoelectric ceramics, produced via laser floating zone (LFZ) method, have been systematically investigated. XRD patterns are quite similar for all samples and main peaks in the patterns correspond to reflection planes of the thermoelectric phase together with small amount of secondary phases. SEM micrographs revealed well oriented grains along the growth direction, and the presence of three different contrasts, associated through EDS to different phases, namely, black (Co oxide), white (Bi poor phase) and grey (Bi2Ca2Co1.7Oy TE phase). It was also seen that the amount of secondary phases diminishes with K-increase. The room-temperature resistivity values sharply decrease from 0.75 mO.m for the undoped sample to 0.44 mO.m for the 0.05 K-doped one, increasing for higher doping. Seebeck coefficient also decreases from 190 µV K-1 in the pristine sample, to 160 µV K-1 in all the K-doped ones, at 390 K. Thermal conductivity increases with temperature up to around 250 K, decreasing at higher temperatures. Thermal conductivity at 390 K decreases from 1.1 W K-1 m-1 in the pristine sample to lower values by K-doping, reaching the minimum, 0.9 W K-1 m-1, in the 0.125 K-doped one. As a result, the highest ZT value of has been determined in 0.05 K-doped sample, around 0.021 at 390 K. © 2022 IOP Publishing Ltd.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhanced thermoelectric properties in Bi2Sr2-XBaxCo2Oy ceramics by Ba doping

  • Özkurt, B.
  • Madre Sediles, M. A.
  • Sotelo Mieg, A.
  • Torres Portero, M. A.
Bi2Sr2-xBaxCo2Oy polycrystalline samples (0.00 = × =0.15) were prepared through the classical solid-state reaction method. It has been found that Ba-doped Bi2Sr2Co2Oy was obtained as major phase in all samples, based on XRD results. On the other hand, SEM studies have shown the presence of small amounts of secondary phases. The electrical resistivity values of all Ba doped samples decreased when compared to the undoped one, being minimum for the 0.075Ba doped ones. Seebeck coefficient increase with the increasing temperature in all samples, reaching the highest values in the 0.025 Ba doped sample. Finally, power factor has been calculated using the Seebeck coefficient and electrical resistivity values to determine the thermoelectric performances of samples. The maximum PF value of 0.14 mW/K2 m at 650 °C was obtained for 0.075Ba doped sample, which is around 25% higher than the undoped sample at the same temperature. All these results clearly show that the thermoelectric properties of the Bi2Sr2Co2Oy system can be improved by Ba doping at optimal values. © 2022 Elsevier B.V.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improved copper–epoxy adhesion by laser micro- and nano-structuring of copper surface for thermal applications

  • Mora M.
  • Amaveda H.
  • Porta-Velilla L.
  • de la Fuente G.F.
  • Martínez E.
  • Angurel L.A.
The objective of this work is the enhancement of metal-to-metal bonding to provide high thermal conductivity together with electrical insulation, to be used as heat sinks at room and cryo-genic temperatures. High thermal conductive metal (copper) and epoxy resin (Stycast 2850FT) were used in this study, with the latter also providing the required electrical insulation. The copper surface was irradiated with laser to induce micro- and nano-patterned structures that result in an improvement of the adhesion between the epoxy and the copper. Thus, copper-to-copper bonding strength was characterized by means of mechanical tensile shear tests. The effect of the laser processing on the thermal conductivity properties of the Cu/epoxy/Cu joint at different temperatures, from 10 to 300 K, is also reported. Using adequate laser parameters, it is possible to obtain high bonding strength values limited by cohesive epoxy fracture, together with good thermal conductivity at ambient and cryogenic temperatures. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of Y, La, and Yb simultaneous doping on the thermal conductivity and thermoelectric performances of CaMnO3 ceramics

  • Madre, M. A.
  • Amaveda, H.
  • Dura, O. J.
  • Pelloquin, D.
  • Mora, M.
  • Torres, M. A.
  • Marinel, S.
  • Sotelo, A.
Triple doping of CaMnO3 in different stoichiometric proportions has been studied in bulk sintered materials. They were prepared through the classical ceramic route using planetary milling to decrease the precursors particle sizes. It has been found that particle sizes decrease with the amount of dopant, both in the precursors and in the sintered bodies. XRD patterns showed that all samples were nearly single phase, with small amounts of CaMn2O4 phase. SEM and TEM observations revealed a homogeneous distribution of dopants in the CaMnO3 phase, while EDX showed a composition close to the nominal one. However, HREM imaging has shown some dark regions in the crystallites, with different Ca(Y,La,Yb)/Mn ratios found through STEM image-chemical mapping, which points out to the coexistence of CaMnO3 and CaMn2O4–type domains in the crystallites. Electrical resistivity, absolute Seebeck coefficient and thermal conductivity have been drastically decreased with doping. The highest PF values at 800 ºC have been achieved in 0.02(Y,La,Yb) doped samples (∼ 0.37 mW/K2m), which is among the best reported values in literature. On the other hand, lattice thermal conductivity is dramatically decreased with doping due to the phonon scattering produced by the dopants, the decrease in the grain sizes, and the strains present inside the crystallites, reaching the minimum values at 800 ºC in 0.03(Y,La,Yb) doped samples (∼ 0.8 W/K m). Consequently, ZT reaches the maximum values (∼ 0.29) in 0.03(Y,La,Yb) doped samples due to their very low thermal conductivity, being higher than the best ZT reported values in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Transport and structural properties of MgB2/Fe wires produced by redesigning internal Mg diffusion process

  • Yetis, Hakan
  • Avci, Dogan
  • Karaboga, Firat
  • Aksoy, Canan
  • Gajda, Daniel
  • Martínez, Elena
  • Mehmet Tanyildiz, Fatih
  • Zaleski, Andrzej
  • Babij, Michal
  • Tran, Lan Maria
  • Angurel, Luis Alberto
  • Fuente, G.F. de la
  • Belenli, Ibrahim Belenli
We report transport, electromechanical, and structural properties of single core MgB2/Fe wire produced using a new fabrication method, called designed internal Mg diffusion (IMD) process, which relies on the use of non-stoichiometric Mg + B pellets with excess Mg in place of a central Mg rod used in the standard IMD method. Structural analysis revealed the successful formation of a porous MgB2 structure in the center and a dense circular MgB2 layer surrounding this structure in the designed-IMD wire. Fast transport I-V measurements showed that the designed IMD method increased engineering critical current density (J e) up to twice that of the IMD wires in self-field. The central porous MgB2 structure shared the applied current and indirectly behaved as an internal stabilizer against quench damage at high applied currents. © 2022 IOP Publishing Ltd.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of ceramic particles additions on the properties of Ca3Co4O9

  • Amaveda, H.
  • Mora, M.
  • Dura, O. J.
  • Torres, M. A.
  • Madre, M. A.
  • Marinel, S.
  • Sotelo, A.
Ca3Co4O9 + x wt% B4C, AlN, TiC, TiB2, or TiN (x = 0.0, 0.25, 0.50, and 0.75) samples were prepared by the conventional solid-state route. In all samples, only the Ca3Co4O9 phase was identified by powder XRD. Nevertheless, microstructural studies have shown that most of the additives have reacted with air and Ca3Co4O9 phase on their surfaces, producing new phases. Moreover, it seemed that grain sizes were, at least, slightly reduced. On the other hand, while nearly no modification of the Seebeck coefficient has been observed, independently of the added compound and proportion, electrical resistivity decreased in all cases, when compared to the pristine sample. Consequently, the power factor of samples with additions was higher than the one determined for the pure sample. Linear thermal expansion also decreased with these additives, pointing out to the formation of relatively strong grain boundaries which can improve the carrier mobility and decrease the thermal expansion. The lowest thermal expansion value has been measured in 0.25 wt% B4C samples, being only around 20% higher than that of Al2O3, which can help to reduce the differential thermal expansion in thermoelectric modules working at high temperatures; these results may be very interesting for applications prospects. Article highlights: Addition of different ceramic additives to Ca3Co4O9 phase increases electrical conductivity, and power factor.All additive ceramics react with oxygen and the Ca3Co4O9 phase modifying the properties of pristine compound.The decrease of thermal expansion coefficient will allow reducing the differential thermal expansion in modules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina R.
  • Ertugrul M.
  • Larrea Á.
  • Navarro R.
  • Rico V.
  • Yubero F.
  • González-Elipe A.R.
  • Fuente G.F. de la
  • Angurel L.A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laser-induced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Historical stained-glass window laser preservation: The heat accumulation challenge

  • Maingi, E. M.
  • Alonso, M. P.
  • Angurel, L. A.
  • Rahman, M. A.
  • Chapoulie, R.
  • Dubernet, S.
  • de la Fuente, G. F.
Stained-glass windows form an important part of cultural heritage. Short pulse lasers open new opportunities for safe decontamination. In this work, and for the first time, the interaction of sub-nanosecond and femtosecond pulsed lasers with some contemporary stained-glasses has been analyzed exploring their applicability to safely clean stained-glass windows. The results show that, in these materials, damage can be induced using energy levels below damage thresholds due to the heat accumulation in the coating layer that is being eliminated. The latter generates significant thermal stresses on the glass volume, which induce crack formation. In consequence, in order to apply safe stained-glass cleaning protocols, laser parameters have to be selected to control the temperature increase within this layer. To achieve the latter goal, two alternative irradiation procedures were explored in this work. As a first option, a reduction of the effective pulse repetition frequency to values lower than 20 kHz was applied. A second alternative was used for lasers with pulse repetition rates in the hundreds of kHz. In this case, the burst mode was employed controlling the number of pulses emitted and combined with an adequate time lapse selection between two consecutive burst runs. A proof of concept demonstration was carried out on a stained-glass sample from the Cathedral of Cuenca, dated at the end of the XV century. © 2021 SECV
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Structure, magnetic, photocatalytic and blood compatibility studies of nickel nanoferrites prepared by laser ablation technique in distilled water

  • Özçelik, S.
  • Yalçin, B.
  • Arda, L.
  • Santos, H.
  • Sáez-Puche, R.
  • Angurel, L.A.
  • Fuente, G.F.D.L.
  • Özçelik, B.
The main objective of this study is to investigate the structural features, magnetic behaviour, photocatalytic properties and blood compatibility of NiFe2O4 nanoparticles (NPs) obtained by subnanosecond laser ablation in water. Structure and size distribution of NPs were studied using X-Ray Diffractometry (XRD) and Transmission Electron Microscopy (TEM). The photocatalytic properties of NPs were evaluated by photo-degradation of Methylene Blue (MeB) dye under ambient visible light illumination. Four different kinetic models were used to identify the photocatalytic degradation mechanism of NiFe2O4 nanoparticles and it was found that the pseudo-second-order model was the most suitable type to interpret the experimental kinetic data of MeB photodegradation. The hemocompatibility of NiFe2O4 nanoparticles was studied by hemolysis tests using human erythrocytes drawn from healthy volunteers. NiFe2O4 nanoparticles caused undesirable hemolysis ratios at 0.05, 1 and 5 mg/ml concentrations, while the biologically safe concentration of these nanoparticles was found to be below 0.01 mg/ml.