Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 28
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Contribución de congreso (ConferenceOutput)

GaAsN/GaAsSb superlattices as 1 eV layers for efficient multi-junction solar cells

  • Gonzalo Martín, Alicia
  • Utrilla, A. D.
  • Aeberhard, U.
  • Llorens, J. M.
  • Alén, B.
  • Braza, V.
  • Reyes, D. F.
  • González, D.
  • Fuertes Marrón, D.
  • Hierro, A.
  • Ulloa, J. M.
Proceedings of 2018 IEEE 7th World Conference on Photovoltaic Energy Conversion (WCPEC) (A Joint Conference of 45th IEEE PVSC, 28th PVSEC & 34th EU PVSEC), 10-15 Jun. 2018, Waikoloa, HI, USA, We demonstrate type-II GaAsSb/GaAsN superlattices as a suitable candidate to form a lattice-matched 1.01.15 eV subcell that could significantly improve the performance of multi-junction solar cells. The spatial separation of N and Sb allows better lattice-matching control, composition homogeneity, crystal quality and interface abruptness. Moreover, the type-II band alignment provides effective bandgap and radiative lifetime tunability through the period thickness. For the impact of period thickness on transport, quantum-kinetic simulations support the experimental finding of efficient carrier extraction at thicknesses up to 6 nm. All this leads to single-junction solar cells with improved efficiency under monochromatic illumination over the equivalent bulk devices., We acknowledge funding from the Spanish MINECO through projects MAT2016-77491 C2-1-R, TEC2015-64189-C3-2-R, CM S2013/MAE-2780 and EUIN-2017-88844, and from CSIC through project ICOOP 2017-COOPB20320. UA acknowledges funding by the European Comission through grant no. 676629 (project “EoCoE”). Support of the EU COST Action MP1406 “Multiscale in modelling and validation for solar photovoltaics (MultiscaleSolar)” is also acknowledged.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Photocarrier extraction in GaAsSb/GaAsN type-II QW superlattice solar cells

  • Aeberhard, Urs
  • Gonzalo Martín, Alicia
  • Ulloa, José M.
Photocarrier transport and extraction in GaAsSb/GaAsN type-II quantum well superlattices are investigated by means of inelastic quantum transport calculations based on the non-equilibrium Green's function formalism. Evaluation of the local density of states and the spectral current flow enables the identification of different regimes for carrier localization, transport, and extraction as a function of configurational parameters. These include the number of periods, the thicknesses of the individual layers in one period, the built-in electric field, and the temperature of operation. The results for the carrier extraction efficiency are related to experimental data for different symmetric GaAsSb/GaAsN type-II quantum well superlattice solar cell devices and provide a qualitative explanation for the experimentally observed dependence of photovoltaic device performance on the period thickness., This work benefited from COST action MP1406 – MultiscaleSolar. U.A. acknowledges support through the European Commission Horizon 2020 Project No. 676629, as well as compute time granted on the supercomputer JURECA at the J€ulich Supercomputing Centre (JSC). A.G. and J.M.U. acknowledge Spanish MINECO through project MAT2016-77491-C2-1-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The role of surface recombination on the performance of perovskite solar cells: effect of morphology and crystalline phase of TiO2 contact

  • Idígoras, Jesús
  • Contreras-Bernal, Lidia
  • Cave, James M.
  • Courtier, Nicola E.
  • Barranco, Ángel
  • Borrás, Ana
  • Sánchez-Valencia, J. R.
  • Anta, Juan A.
  • Walker, Alison B.
Herein, the preparation of 1D TiO nanocolumnar films grown by plasma-enhanced chemical vapor deposition is reported as the electron selective layer (ESL) for perovskite solar devices. The impact of the ESL architecture (1D and 3D morphologies) and the nanocrystalline phase (anatase and amorphous) is analyzed. For anatase structures, similar power conversion efficiencies are achieved using an ESL either the 1D nanocolumns or the classical 3D nanoparticle film. However, lower power conversion efficiencies and different optoelectronic properties are found for perovskite devices based on amorphous 1D films. The use of amorphous TiO as electron selective contact produces a bump in the reverse scan of the current–voltage curve as well as an additional electronic signal, detected by impedance spectroscopy measurements. The dependence of this additional signal on the optical excitation wavelength used in the IS experiments suggests that it stems from an interfacial process. Calculations using a drift-diffusion model which explicitly considers the selective contacts reproduces qualitatively the main features observed experimentally. These results demonstrate that for a solar cell in which the contact is working properly the open-circuit photovoltage is mainly determined by bulk recombination, whereas the introduction of a “bad contact” shifts the balance to surface recombination., The authors thank Junta de Andalucía for financial support via grant FQM 1851 and FQM 2310. The authors thank Ministerio de Economía y Competitividad of Spain and Agencia Estatal de Investigación (AEI) and EU (FEDER) under grants MAT2013‐47192‐C3‐3‐R, MAT2016‐76892‐C3‐2‐R, MAT2016‐79866‐R and Red de Excelencia “Emerging photovoltaic Technologies” for financial support. J.R.S.‐V. and A.B. acknowledge Marie Skłodowska‐Curie ActionsH2020‐MSCA‐IF‐2014 PlasmaPerovSol grant (Project ID 661480) and the University of Seville through the VI PPIT‐US. J.M.C. and N.E.C. were supported by EPSRC funded studentships from the CDT in New and Sustainable Photovoltaics (reference EP/L01551X/1). A.B.W. was supported by the Energy oriented Centre of Excellence (EoCoE), Horizon2020 grant research number 676629.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A CFD framework for offshore and onshore wind farm simulation

  • Avila, Matias
  • Gargallo-Peiró, Abel
  • Folch, Arnau|||0000-0002-0677-6366
We present a wind simulation framework for offshore and onshore wind farms. The simulation framework involves an automatic hybrid high-quality mesh generation process, a pre-processing to impose initial and boundary conditions, and a solver for the Reynolds Averaged Navier-Stokes (RANS) equations with two different turbulence models, a modified standard k-epsilon model and a realizable k-epsilon model in which we included the Coriolis effects. Wind turbines are modeled as actuator discs. The wind farm simulation framework has been implemented in Alya, an in-house High Performance Computing (HPC) multi-physics finite element parallel solver. An application example is shown for an onshore wind farm composed of 165 turbines., This work has been supported by the EU H2020 projects New European Wind Atlas ERA-NET PLUS (NEWA), High Performance Computing for Energy (HPC4E, grant agreement 689772), and the Energy oriented Centre of Excellence (EoCoE, grant agreement 676629). We also thank two anonymous reviewers for their constructive comments on the first version of the manuscript., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Mesh generation, sizing and convergence for onshore and offshore wind farm Atmospheric Boundary Layer flow simulation with actuator discs

  • Gargallo Peiró, Abel|||0000-0003-3742-2197
  • Avila, Matias
  • Owen, Herbert
  • Prieto-Godino, Luis
  • Folch, Arnau|||0000-0002-0677-6366
A new mesh generation process for wind farm modeling is presented together with a mesh convergence and sizing analysis for wind farm flow simulations. The generated meshes are tailored to simulate Atmospheric Boundary Layer (ABL) flows on complex terrains modeling the wind turbines as actuator discs. The wind farm mesher is fully automatic and, given the topography and the turbine characteristics (location, diameter and hub height), it generates a hybrid mesh conformal with the actuator discs and refined upwind and downstream. Moreover, it presents smooth element size transitions across scales and avoids extending high-resolution areas to all the domain. We take advantage of our automatic and robust mesher to study the mesh convergence of our RANS solver with linear elements, obtaining quadratic mesh convergence for a quantity of interest in all the tested cases. In addition, we quantify the mesh resolution at the terrain surface and at the actuator discs required to achieve a given numerical error in simulations in onshore and offshore frameworks. Finally, we present the generated meshes and the simulation results for an offshore and an onshore wind farm. We analyze in detail one particular wind direction for both cases, and for the onshore wind farm we use our automatic framework to estimate the yearly production of energy and measuring the error against the actual produced one., This work has been partially funded by the EU H2020Energy oriented Center of Excellence (EoCoE) for computer applications, the New European Wind Atlas (NEWA) and the High Performance Computing for Energy (HPC4E) projects. We thank Iberdrola Renovables for their collaboration and for providing wind farm data to validate the developed techniques., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Complexity Reduction in Large Quantum Systems: Fragment Identification and Population Analysis via a Local Optimized Minimal Basis

  • Mohr, Stephan|||0000-0003-2510-5805
  • Masella, Michel
  • Ratcliff, Laura E.
  • Genovese, Luigi
We present, within Kohn–Sham density functional theory calculations, a quantitative method to identify and assess the partitioning of a large quantum-mechanical system into fragments. We then show how within this framework simple generalizations of other well-known population analyses can be used to extract, from first-principles, reliable electrostatic multipoles for the identified fragments. Our approach reduces arbitrariness in the fragmentation procedure and enables the possibility to assess quantitatively whether the corresponding fragment multipoles can be interpreted as observable quantities associated with a system moiety. By applying our formalism within the code BigDFT, we show that the use of a minimal set of in situ-optimized basis functions allows at the same time a proper fragment definition and an accurate description of the electronic structure., We would like to thank Thierry Deutsch for valuable discussions and Fátima Lucas for providing various test systems and helpful discussions. This research used resources of the Argonne Leadership Computing Facility, which is a DOE Office of Science User Facility supported under Contract DEAC02-06CH11357. SM acknowledges support from the European Centre of Excellence MaX (project ID 676598). LG acknowledges support from the EU ExtMOS project (project ID 646176) and the European Centre of Excellence EoCoE (project ID 676629)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A wind field downscaling strategy based on domain segmentation and transfer functions

  • Barcons, Jordi
  • Avila, Matias
  • Folch, Arnau|||0000-0002-0677-6366
This paper presents a novel methodology for mesoscale‐to‐microscale downscaling of near‐surface wind fields. The model chain consists on the Weather Research and Forecast mesoscale model and the Alya‐CFDWind microscale model (assuming neutral stability). The downscaling methodology combines precomputed microscale simulations with a mesoscale forecast using a domain segmentation technique and transfer functions. As a result, the downscaled wind field preserves the mesoscale pattern but, at the same time, incorporates local mesoscale subgrid terrain effects, particularly at valleys and channelling zones. The methodology has been validated over a 9‐month period on a very complex terrain site instrumented with a dense observational network of meteorological masts. With respect to mesoscale results, the global skills of the downscaled wind at masts improve for wind direction and remain similar for wind velocity. However, a substantial improvement occurs under stable and neutral conditions and for high wind velocity regimes., This work has been partially funded by the High Performance Computing for Energy (HPC4E) project (call H2020-EUB-2015, Topic: EUB-2-2015, type of action RIA, Grant Agreement number 689772) and the SEDAR ("Simulación eólica de alta resolución") project. It has also been partially supported by the Energy-oriented Centre of Excellence (EoCoE) (Grant Agreement number 676629, funded within the H2020 framework of the EuropeanUnion). J.B. is grateful to a PhD fellowship from the IndustrialDoctorates Plan of the Government of Catalonia (Ref. eco/2497/2013). We also thank Daniel Paredes and Luis Prieto from Iberdrola Renovables S.A. for providing us access to met masts data for validation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Capítulo o parte de un libro (BookPart)

High-Performance Computing: Do’s and Dont’s

  • Houzeaux, Guillaume|||0000-0002-2592-1426
  • Borrell, Ricard
  • Fournier, Yvan
  • Garcia-Gasulla, Marta
  • Göbbert, Jens H.
  • Hachem, Elie
  • Mehta, Vishal
  • Mesri, Youssef
  • Owen, Herbert
  • Vázquez, Mariano|||0000-0002-2526-6708
Computational fluid dynamics (CFD) is the main field of computational mechanics that has historically benefited from advances in high-performance computing. High-performance computing involves several techniques to make a simulation efficient and fast, such as distributed memory parallelism, shared memory parallelism, vectorization, memory access optimizations, etc. As an introduction, we present the anatomy of supercomputers, with special emphasis on HPC aspects relevant to CFD. Then, we develop some of the HPC concepts and numerical techniques applied to the complete CFD simulation framework: from preprocess (meshing) to postprocess (visualization) through the simulation itself (assembly and iterative solvers)., Part of the research developments and results presented in this chapter were funded by: the European Union’s Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP) under the HPC4E Project, grant agreement 689772; EoCoE, a project funded by the European Union Contract H2020-EINFRA-2015-1-676629; PRACE Type C and Type A projects., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Diurnal cycle RANS simulations applied to wind resource assessment

  • Barcons, Jordi
  • Avila, Matias
  • Folch, Arnau|||0000-0002-0677-6366
Microscale computational fluid dynamics (CFD) models can be used for wind resource assessment on complex terrains. These models generally assume neutral atmospheric stratification, an assumption that can lead to inaccurate modeling results and to large uncertainties at certain sites. We propose a methodology for wind resource evaluation based on unsteady Reynolds averaged Navier‐Stokes (URANS) simulations of diurnal cycles including the effect of thermal stratification. Time‐dependent boundary conditions are generated by a 1D precursor to drive 3D diurnal cycle simulations for a given geostrophic wind direction sector. Time instants of the cycle representative of four thermal stability regimes are sampled within diurnal cycle simulations and combined with masts time series to obtain the wind power density (WPD). The methodology has been validated on a complex site instrumented with seven met masts. The WPD spatial distribution is in good agreement with observations with the mean absolute error improving 17.1% with respect to the neutral stratification assumption., This work has been partially supported by the three EU H2020 projects, New European Wind Atlas ERA‐NET PLUS (NEWA, FP7‐ENERGY.2013.10.1.2, European Commission's grant agreement 618122), High Performance Computing for Energy (HPC4E, grant agreement 689772), and the Energy oriented Centre of Excellence (EoCoE, grant agreement 676629), and the SEDAR (“Simulación eólica de alta resolución”) project. Jordi Barcons is grateful to a PhD fellowship from the Industrial Doctorates Plan of the Government of Catalonia (Ref. eco/2497/2013). We also thank Iberdrola Renovables Energa S.A. and Impulsora Latinoamericana de Energa Renovables S.A. for providing the access to Puebla met masts data for validation and to Luis Prieto and Daniel Paredes for their help. We also thank the reviewers for their productive comments and observations., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Efficient Computation of Sparse Matrix Functions for Large-Scale Electronic Structure Calculations: The CheSS Library

  • Mohr, Stephan|||0000-0003-2510-5805
  • Dawson, William
  • Wagner, Michael
  • Caliste, Damien
  • Nakajima, Takahito
  • Genovese, Luigi
We present CheSS, the “Chebyshev Sparse Solvers” library, which has been designed to solve typical problems arising in large-scale electronic structure calculations using localized basis sets. The library is based on a flexible and efficient expansion in terms of Chebyshev polynomials and presently features the calculation of the density matrix, the calculation of matrix powers for arbitrary powers, and the extraction of eigenvalues in a selected interval. CheSS is able to exploit the sparsity of the matrices and scales linearly with respect to the number of nonzero entries, making it well-suited for large-scale calculations. The approach is particularly adapted for setups leading to small spectral widths of the involved matrices and outperforms alternative methods in this regime. By coupling CheSS to the DFT code BigDFT, we show that such a favorable setup is indeed possible in practice. In addition, the approach based on Chebyshev polynomials can be massively parallelized, and CheSS exhibits excellent scaling up to thousands of cores even for relatively small matrix sizes., We gratefully acknowledge the support of the MaX (SM) and POP (MW) projects, which have received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 676598 and 676553, respectively. This work was also supported by the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union, as well as by the Next-Generation Supercomputer project (the K computer project) and the FLAGSHIP2020 within the priority study5 (Development of new fundamental technologies for high-efficiency energy creation, conversion/storage and use) from the Ministry of Education, Culture, Sports, Science and Technology (MEXT) of Japan. We (LG, DC, WD, TN) gratefully acknowledge the joint CEA-RIKEN collaboration action., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Large eddy simulation for automotive aerodynamics with Alya

  • Lehmkuhl Barba, Oriol|||0000-0002-2670-1871
  • Chrysokentis, Georgios
  • Gomez, Samuel
  • Owen, Herbert
The prodigious potential offered by the ever-growing computing infrastructure is fostering the use of large eddy simulation for automotive aerodynamics. This approach, which resolves the larger dynamically important eddies and models only the smaller ones, provides significant improvement over RANS when there are important separated regions or transient phenomena such as noise generation. In the search for high fidelity LES solution Alya has recently undergone a significant transformation departing from the use of the Variational Multiscale approach and implicit temporal discretization. Nowadays, Alya has switched to an explicit temporal discretization, without any stabilization other than the pressure stabilization introduced by the fractional step scheme. When using a energy conserving discretization for the convective term together with an explicit turbulent model, numerical stabilization of the convective term in the Navier Stokes equations is not needed. The Vreman turbulence model is used in this work. For the simulation of high Reynolds number turbulent flows, such as those encountered in automotive applications, the use of wall modeling is mandatory with current computational resources. Significant improvements in the implementation of wall modeling for finite element methods proposed recently are tested in this work for highly complex geometries. Comparison of the numerical results for both the Ahmed and DrivAer bodies against experimental results from the literature shows that Alya can provide very accurate results.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

MPI+X: task-based parallelization and dynamic load balance of finite element assembly

  • Garcia-Gasulla, Marta
  • Houzeaux, Guillaume|||0000-0002-2592-1426
  • Ferrer, Roger
  • Artigues, Antoni
  • López, Victor
  • Labarta Mancho, Jesús José|||0000-0002-7489-4727
  • Vázquez, Mariano|||0000-0002-2526-6708
The main computing tasks of a finite element code(FE) for solving partial differential equations (PDE's) are the algebraic system assembly and the iterative solver. This work focuses on the first task, in the context of a hybrid MPI+X paradigm. Although we will describe algorithms in the FE context, a similar strategy can be straightforwardly applied to other discretization methods, like the finite volume method. The matrix assembly consists of a loop over the elements of the MPI partition to compute element matrices and right-hand sides and their assemblies in the local system to each MPI partition. In a MPI+X hybrid parallelism context, X has consisted traditionally of loop parallelism using OpenMP. Several strate- gies have been proposed in the literature to implement this loop parallelism, like coloring or substructuring techniques to circumvent the race condition that appears when assembling the element system into the local system. The main drawback of the first technique is the decrease of the IPC due to bad spatial locality. The second technique avoids this issue but requires extensive changes in the implementation, which can be cumbersome when several element loops should be treated. We propose an alternative, based on the task parallelism of the element loop using some extensions to the OpenMP programming model. The task- ification of the assembly solves both aforementioned problems. In addition, dynamic load balance will be applied using the DLB library, especially efficient in the presence of hybrid meshes, where the relative costs of the different elements is impossible to estimate a priori. This paper presents the proposed methodology, its implementation and its validation through the solution of large computational mechanics problems up to 16k cores., The use of large part of a supercomputer, even more in normal conditions of use, is never an innocuous exercise. The research leading to these results has received funding from: the European Union's Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP), HPC4E Project, grant agreement 689772; the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union; The Spanish Government (grant SEV2015-0493 of the Severo Ochoa Program); the Spanish Ministry of Science and Innovation (contract TIN2015-65316-P); the Generalitat de Catalunya (contract 2014-SGR-1051); the Intel-BSC Exascale Lab collaboration project. Comissió Interdepartamental de Recerca i Innovació Tecnológica(Interdepartmental Commission for Research and Technological Innovation), Sí
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Benefits of SMT and of Parallel Transpose Algorithm for the Large-Scale GYSELA Application

  • Latu, Guillaume
  • Bigot, Julien
  • Bouzat, Nicolas
  • Gimenez, Judit
  • Grandgirard, Virginie
This article describes how we manage to increase performance and to extend features of a large parallel application through the use of simultaneous multithreading (SMT) and by designing a robust parallel transpose algorithm. The semi-Lagrangian code Gysela typically performs large physics simulations using a few thousands of cores, between 1k cores up to 16k on x86-based clusters. However, simulations with finer resolutions and with kinetic electrons increase those needs by a huge factor, providing a good example of applications requiring Exascale machines. To improve Gysela compute times, we take advantage of efficient SMT implementations available on recent INTEL architectures. We also analyze the cost of a transposition communication scheme that involves a large number of cores in our case. Adaptation of the code for balance load whenever using both SMT and good deployment strategy led to a significant reduction that can be up to 38% of the execution times., This work was strongly supported by the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon 2020 framework of the European Union. We gratefully acknowledge the POP project, that has also received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 676553. This work was possible due to the generous computational and software engineering supports from FZJ Juelich (Germany) and CCRT Bruyères- le-Châtel (France). The authors would also like to thank Chantal Passeron for assistance and for her precious help., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

MPI+X: task-based parallelisation and dynamic load balance of finite element assembly

  • Garcia, Marta
  • Houzeaux, Guillaume|||0000-0002-2592-1426
  • Ferrer, Roger
  • Artigues, Antoni
  • López, Victor
  • Labarta Mancho, Jesús José|||0000-0002-7489-4727
  • Vázquez, Mariano|||0000-0002-2526-6708
The main computing phases of numerical methods for solving partial differential equations are the algebraic system assembly and the iterative solver. This work focuses on the first task, in the context of a hybrid MPI+X paradigm. The matrix assembly consists of a loop over the elements, faces, edges or nodes of the MPI partitions to compute element matrices and vectors and then of their assemblies. In a MPI+X hybrid parallelism context, X has consisted traditionally of loop parallelism using OpenMP, with different techniques to avoid the race condition, but presenting efficiency or implementation drawbacks. We propose an alternative, based on task parallelism using some extensions to the OpenMP programming model. In addition, dynamic load balance will be applied, especially efficient in the presence of hybrid meshes. This paper presents the proposed methodology, its implementation and its validation through the solution of large computational mechanics problems up to 16k cores., The research leading to these results has received funding from: the European Union's Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP), HPC4E Project, grant agreement 689772; the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union; The Spanish Government (grant SEV2015-0493 of the Severo Ochoa Program); the Spanish Ministry of Science and Innovation (contract TIN2015-65316-P); the Generalitat de Catalunya (contract 2014-SGR-1051); the Intel-BSC Exascale Lab collaboration project. Comissió Interdepartamental de Recerca i Innovació Tecnológica(Interdepartmental Commission for Research and Technological Innovation), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A hybrid meshing framework adapted to the topography to simulate atmospheric boundary layer flows

  • Gargallo Peiró, Abel|||0000-0003-3742-2197
  • Avila, Matias
  • Folch, Arnau|||0000-0002-0677-6366
A new topography adapted mesh generation framework tailored to simulate Atmospheric Boundary Layer (ABL) flows on complex terrains is presented. The mesher is fully automatic given: the maximum and minimum surface mesh size, and the mesh size at the top of the ABL. The following contributions to the meshing workflow for ABL flow simulation are performed. First, we present a smooth topography modeling to query first and second-order geometry derivatives. Second, we propose a new adaptive meshing procedure to discretize the topography based on two different metrics. Third, we present the ABL mesher, featuring both prisms and tetrahedra. We extrude the triangles of the adapted surface mesh, generating prisms that reproduce the Surface Boundary Layer. Then, the rest of the domain is meshed with an unstructured tetrahedral mesh. In addition, we detail a hybrid quality optimization approach for both the surface and volume meshers, analyzing its impact on the solver for high-complexity terrains. We analyze the convergence of the triangle adaptive approach, obtaining quadratic convergence to the geometry and reducing to one-half the error for the same amount of degrees of freedom than without adaptivity and optimization. We also study the mesh convergence of our Reynolds-averaged Navier–Stokes (RANS) solver, obtaining quadratic mesh convergence to the solution, and using a 30% of the degrees of freedom while reducing a 20% of the error of standard semi-structured approaches. Finally, we present the generated meshes and the simulation results for a complete complex topographic scenario., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A hybrid meshing framework adapted to the topography to simulate atmospheric boundary layer flows

  • Gargallo Peiró, Abel
  • Avila, Matias
  • Folch, Arnau
A new topography adapted mesh generation framework tailored to simulate Atmospheric Boundary Layer (ABL) flows on complex terrains is presented. The mesher is fully automatic given: the maximum and minimum surface mesh size, and the mesh size at the top of the ABL. The following contributions to the meshing workflow for ABL flow simulation are performed. First, we present a smooth topography modeling to query first and second-order geometry derivatives. Second, we propose a new adaptive meshing procedure to discretize the topography based on two different metrics. Third, we present the ABL mesher, featuring both prisms and tetrahedra. We extrude the triangles of the adapted surface mesh, generating prisms that reproduce the Surface Boundary Layer. Then, the rest of the domain is meshed with an unstructured tetrahedral mesh. In addition, we detail a hybrid quality optimization approach for both the surface and volume meshers, analyzing its impact on the solver for high-complexity terrains. We analyze the convergence of the triangle adaptive approach, obtaining quadratic convergence to the geometry and reducing to one-half the error for the same amount of degrees of freedom than without adaptivity and optimization. We also study the mesh convergence of our Reynolds-averaged Navier–Stokes (RANS) solver, obtaining quadratic mesh convergence to the solution, and using a 30% of the degrees of freedom while reducing a 20% of the error of standard semi-structured approaches. Finally, we present the generated meshes and the simulation results for a complete complex topographic scenario., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication

High-Performance Computing: Do’s and Dont’s

  • Houzeaux, Guillaume
  • Borrell, Ricard
  • Fournier, Yvan
  • Garcia-Gasulla, Marta
  • Göbbert, Jens H.
  • Hachem, Elie
  • Mehta, Vishal
  • Mesri, Youssef
  • Owen, Herbert
  • Vázquez, Mariano
Computational fluid dynamics (CFD) is the main field of computational mechanics that has historically benefited from advances in high-performance computing. High-performance computing involves several techniques to make a simulation efficient and fast, such as distributed memory parallelism, shared memory parallelism, vectorization, memory access optimizations, etc. As an introduction, we present the anatomy of supercomputers, with special emphasis on HPC aspects relevant to CFD. Then, we develop some of the HPC concepts and numerical techniques applied to the complete CFD simulation framework: from preprocess (meshing) to postprocess (visualization) through the simulation itself (assembly and iterative solvers)., Part of the research developments and results presented in this chapter were funded by: the European Union’s Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP) under the HPC4E Project, grant agreement 689772; EoCoE, a project funded by the European Union Contract H2020-EINFRA-2015-1-676629; PRACE Type C and Type A projects., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Large eddy simulation for automotive aerodynamics with Alya

  • Lehmkuhl Barba, Oriol
  • Chrysokentis, Georgios
  • Gomez, Samuel
  • Owen, Herbert
The prodigious potential offered by the ever-growing computing infrastructure is fostering the use of large eddy simulation for automotive aerodynamics. This approach, which resolves the larger dynamically important eddies and models only the smaller ones, provides significant improvement over RANS when there are important separated regions or transient phenomena such as noise generation. In the search for high fidelity LES solution Alya has recently undergone a significant transformation departing from the use of the Variational Multiscale approach and implicit temporal discretization. Nowadays, Alya has switched to an explicit temporal discretization, without any stabilization other than the pressure stabilization introduced by the fractional step scheme. When using a energy conserving discretization for the convective term together with an explicit turbulent model, numerical stabilization of the convective term in the Navier Stokes equations is not needed. The Vreman turbulence model is used in this work. For the simulation of high Reynolds number turbulent flows, such as those encountered in automotive applications, the use of wall modeling is mandatory with current computational resources. Significant improvements in the implementation of wall modeling for finite element methods proposed recently are tested in this work for highly complex geometries. Comparison of the numerical results for both the Ahmed and DrivAer bodies against experimental results from the literature shows that Alya can provide very accurate results., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A CFD framework for offshore and onshore wind farm simulation

  • Avila, Matias
  • Gargallo-Peiró, Abel
  • Folch, Arnau
We present a wind simulation framework for offshore and onshore wind farms. The simulation framework involves an automatic hybrid high-quality mesh generation process, a pre-processing to impose initial and boundary conditions, and a solver for the Reynolds Averaged Navier-Stokes (RANS) equations with two different turbulence models, a modified standard k-epsilon model and a realizable k-epsilon model in which we included the Coriolis effects. Wind turbines are modeled as actuator discs. The wind farm simulation framework has been implemented in Alya, an in-house High Performance Computing (HPC) multi-physics finite element parallel solver. An application example is shown for an onshore wind farm composed of 165 turbines., This work has been supported by the EU H2020 projects New European Wind Atlas ERA-NET PLUS (NEWA), High Performance Computing for Energy (HPC4E, grant agreement 689772), and the Energy oriented Centre of Excellence (EoCoE, grant agreement 676629). We also thank two anonymous reviewers for their constructive comments on the first version of the manuscript., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

MPI+X: task-based parallelization and dynamic load balance of finite element assembly

  • Garcia-Gasulla, Marta
  • Houzeaux, Guillaume
  • Ferrer, Roger
  • Artigues, Antoni
  • López, Victor
  • Labarta Mancho, Jesús José
  • Vázquez, Mariano
The main computing tasks of a finite element code(FE) for solving partial differential equations (PDE's) are the algebraic system assembly and the iterative solver. This work focuses on the first task, in the context of a hybrid MPI+X paradigm. Although we will describe algorithms in the FE context, a similar strategy can be straightforwardly applied to other discretization methods, like the finite volume method. The matrix assembly consists of a loop over the elements of the MPI partition to compute element matrices and right-hand sides and their assemblies in the local system to each MPI partition. In a MPI+X hybrid parallelism context, X has consisted traditionally of loop parallelism using OpenMP. Several strate- gies have been proposed in the literature to implement this loop parallelism, like coloring or substructuring techniques to circumvent the race condition that appears when assembling the element system into the local system. The main drawback of the first technique is the decrease of the IPC due to bad spatial locality. The second technique avoids this issue but requires extensive changes in the implementation, which can be cumbersome when several element loops should be treated. We propose an alternative, based on the task parallelism of the element loop using some extensions to the OpenMP programming model. The task- ification of the assembly solves both aforementioned problems. In addition, dynamic load balance will be applied using the DLB library, especially efficient in the presence of hybrid meshes, where the relative costs of the different elements is impossible to estimate a priori. This paper presents the proposed methodology, its implementation and its validation through the solution of large computational mechanics problems up to 16k cores., The use of large part of a supercomputer, even more in normal conditions of use, is never an innocuous exercise. The research leading to these results has received funding from: the European Union's Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP), HPC4E Project, grant agreement 689772; the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union; The Spanish Government (grant SEV2015-0493 of the Severo Ochoa Program); the Spanish Ministry of Science and Innovation (contract TIN2015-65316-P); the Generalitat de Catalunya (contract 2014-SGR-1051); the Intel-BSC Exascale Lab collaboration project. Comissió Interdepartamental de Recerca i Innovació Tecnológica(Interdepartmental Commission for Research and Technological Innovation), Sí, Post-print (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

MPI+X: task-based parallelisation and dynamic load balance of finite element assembly

  • Garcia, Marta
  • Houzeaux, Guillaume
  • Ferrer, Roger
  • Artigues, Antoni
  • López, Victor
  • Labarta Mancho, Jesús José
  • Vázquez, Mariano
The main computing phases of numerical methods for solving partial differential equations are the algebraic system assembly and the iterative solver. This work focuses on the first task, in the context of a hybrid MPI+X paradigm. The matrix assembly consists of a loop over the elements, faces, edges or nodes of the MPI partitions to compute element matrices and vectors and then of their assemblies. In a MPI+X hybrid parallelism context, X has consisted traditionally of loop parallelism using OpenMP, with different techniques to avoid the race condition, but presenting efficiency or implementation drawbacks. We propose an alternative, based on task parallelism using some extensions to the OpenMP programming model. In addition, dynamic load balance will be applied, especially efficient in the presence of hybrid meshes. This paper presents the proposed methodology, its implementation and its validation through the solution of large computational mechanics problems up to 16k cores., The research leading to these results has received funding from: the European Union's Horizon 2020 Programme (2014–2020) and from Brazilian Ministry of Science, Technology and Innovation through Rede Nacional de Pesquisa (RNP), HPC4E Project, grant agreement 689772; the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union; The Spanish Government (grant SEV2015-0493 of the Severo Ochoa Program); the Spanish Ministry of Science and Innovation (contract TIN2015-65316-P); the Generalitat de Catalunya (contract 2014-SGR-1051); the Intel-BSC Exascale Lab collaboration project. Comissió Interdepartamental de Recerca i Innovació Tecnológica(Interdepartmental Commission for Research and Technological Innovation), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Diurnal cycle RANS simulations applied to wind resource assessment

  • Barcons, Jordi
  • Avila, Matias
  • Folch, Arnau
Microscale computational fluid dynamics (CFD) models can be used for wind resource assessment on complex terrains. These models generally assume neutral atmospheric stratification, an assumption that can lead to inaccurate modeling results and to large uncertainties at certain sites. We propose a methodology for wind resource evaluation based on unsteady Reynolds averaged Navier‐Stokes (URANS) simulations of diurnal cycles including the effect of thermal stratification. Time‐dependent boundary conditions are generated by a 1D precursor to drive 3D diurnal cycle simulations for a given geostrophic wind direction sector. Time instants of the cycle representative of four thermal stability regimes are sampled within diurnal cycle simulations and combined with masts time series to obtain the wind power density (WPD). The methodology has been validated on a complex site instrumented with seven met masts. The WPD spatial distribution is in good agreement with observations with the mean absolute error improving 17.1% with respect to the neutral stratification assumption., This work has been partially supported by the three EU H2020 projects, New European Wind Atlas ERA‐NET PLUS (NEWA, FP7‐ENERGY.2013.10.1.2, European Commission's grant agreement 618122), High Performance Computing for Energy (HPC4E, grant agreement 689772), and the Energy oriented Centre of Excellence (EoCoE, grant agreement 676629), and the SEDAR (“Simulación eólica de alta resolución”) project. Jordi Barcons is grateful to a PhD fellowship from the Industrial Doctorates Plan of the Government of Catalonia (Ref. eco/2497/2013). We also thank Iberdrola Renovables Energa S.A. and Impulsora Latinoamericana de Energa Renovables S.A. for providing the access to Puebla met masts data for validation and to Luis Prieto and Daniel Paredes for their help. We also thank the reviewers for their productive comments and observations., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Efficient Computation of Sparse Matrix Functions for Large-Scale Electronic Structure Calculations: The CheSS Library

  • Mohr, Stephan
  • Dawson, William
  • Wagner, Michael
  • Caliste, Damien
  • Nakajima, Takahito
  • Genovese, Luigi
We present CheSS, the “Chebyshev Sparse Solvers” library, which has been designed to solve typical problems arising in large-scale electronic structure calculations using localized basis sets. The library is based on a flexible and efficient expansion in terms of Chebyshev polynomials and presently features the calculation of the density matrix, the calculation of matrix powers for arbitrary powers, and the extraction of eigenvalues in a selected interval. CheSS is able to exploit the sparsity of the matrices and scales linearly with respect to the number of nonzero entries, making it well-suited for large-scale calculations. The approach is particularly adapted for setups leading to small spectral widths of the involved matrices and outperforms alternative methods in this regime. By coupling CheSS to the DFT code BigDFT, we show that such a favorable setup is indeed possible in practice. In addition, the approach based on Chebyshev polynomials can be massively parallelized, and CheSS exhibits excellent scaling up to thousands of cores even for relatively small matrix sizes., We gratefully acknowledge the support of the MaX (SM) and POP (MW) projects, which have received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 676598 and 676553, respectively. This work was also supported by the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon2020 framework of the European Union, as well as by the Next-Generation Supercomputer project (the K computer project) and the FLAGSHIP2020 within the priority study5 (Development of new fundamental technologies for high-efficiency energy creation, conversion/storage and use) from the Ministry of Education, Culture, Sports, Science and Technology (MEXT) of Japan. We (LG, DC, WD, TN) gratefully acknowledge the joint CEA-RIKEN collaboration action., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Benefits of SMT and of Parallel Transpose Algorithm for the Large-Scale GYSELA Application

  • Latu, Guillaume
  • Bigot, Julien
  • Bouzat, Nicolas
  • Gimenez, Judit
  • Grandgirard, Virginie
This article describes how we manage to increase performance and to extend features of a large parallel application through the use of simultaneous multithreading (SMT) and by designing a robust parallel transpose algorithm. The semi-Lagrangian code Gysela typically performs large physics simulations using a few thousands of cores, between 1k cores up to 16k on x86-based clusters. However, simulations with finer resolutions and with kinetic electrons increase those needs by a huge factor, providing a good example of applications requiring Exascale machines. To improve Gysela compute times, we take advantage of efficient SMT implementations available on recent INTEL architectures. We also analyze the cost of a transposition communication scheme that involves a large number of cores in our case. Adaptation of the code for balance load whenever using both SMT and good deployment strategy led to a significant reduction that can be up to 38% of the execution times., This work was strongly supported by the Energy oriented Centre of Excellence (EoCoE), grant agreement number 676629, funded within the Horizon 2020 framework of the European Union. We gratefully acknowledge the POP project, that has also received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 676553. This work was possible due to the generous computational and software engineering supports from FZJ Juelich (Germany) and CCRT Bruyères- le-Châtel (France). The authors would also like to thank Chantal Passeron for assistance and for her precious help., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A wind field downscaling strategy based on domain segmentation and transfer functions

  • Barcons, Jordi
  • Avila, Matias
  • Folch, Arnau
This paper presents a novel methodology for mesoscale‐to‐microscale downscaling of near‐surface wind fields. The model chain consists on the Weather Research and Forecast mesoscale model and the Alya‐CFDWind microscale model (assuming neutral stability). The downscaling methodology combines precomputed microscale simulations with a mesoscale forecast using a domain segmentation technique and transfer functions. As a result, the downscaled wind field preserves the mesoscale pattern but, at the same time, incorporates local mesoscale subgrid terrain effects, particularly at valleys and channelling zones. The methodology has been validated over a 9‐month period on a very complex terrain site instrumented with a dense observational network of meteorological masts. With respect to mesoscale results, the global skills of the downscaled wind at masts improve for wind direction and remain similar for wind velocity. However, a substantial improvement occurs under stable and neutral conditions and for high wind velocity regimes., This work has been partially funded by the High Performance Computing for Energy (HPC4E) project (call H2020-EUB-2015, Topic: EUB-2-2015, type of action RIA, Grant Agreement number 689772) and the SEDAR ("Simulación eólica de alta resolución") project. It has also been partially supported by the Energy-oriented Centre of Excellence (EoCoE) (Grant Agreement number 676629, funded within the H2020 framework of the EuropeanUnion). J.B. is grateful to a PhD fellowship from the IndustrialDoctorates Plan of the Government of Catalonia (Ref. eco/2497/2013). We also thank Daniel Paredes and Luis Prieto from Iberdrola Renovables S.A. for providing us access to met masts data for validation., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Complexity Reduction in Large Quantum Systems: Fragment Identification and Population Analysis via a Local Optimized Minimal Basis

  • Mohr, Stephan
  • Masella, Michel
  • Ratcliff, Laura E.
  • Genovese, Luigi
We present, within Kohn–Sham density functional theory calculations, a quantitative method to identify and assess the partitioning of a large quantum-mechanical system into fragments. We then show how within this framework simple generalizations of other well-known population analyses can be used to extract, from first-principles, reliable electrostatic multipoles for the identified fragments. Our approach reduces arbitrariness in the fragmentation procedure and enables the possibility to assess quantitatively whether the corresponding fragment multipoles can be interpreted as observable quantities associated with a system moiety. By applying our formalism within the code BigDFT, we show that the use of a minimal set of in situ-optimized basis functions allows at the same time a proper fragment definition and an accurate description of the electronic structure., We would like to thank Thierry Deutsch for valuable discussions and Fátima Lucas for providing various test systems and helpful discussions. This research used resources of the Argonne Leadership Computing Facility, which is a DOE Office of Science User Facility supported under Contract DEAC02-06CH11357. SM acknowledges support from the European Centre of Excellence MaX (project ID 676598). LG acknowledges support from the EU ExtMOS project (project ID 646176) and the European Centre of Excellence EoCoE (project ID 676629)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Mesh generation, sizing and convergence for onshore and offshore wind farm Atmospheric Boundary Layer flow simulation with actuator discs

  • Gargallo Peiró, Abel
  • Avila, Matias
  • Owen, Herbert
  • Prieto-Godino, Luis
  • Folch, Arnau
A new mesh generation process for wind farm modeling is presented together with a mesh convergence and sizing analysis for wind farm flow simulations. The generated meshes are tailored to simulate Atmospheric Boundary Layer (ABL) flows on complex terrains modeling the wind turbines as actuator discs. The wind farm mesher is fully automatic and, given the topography and the turbine characteristics (location, diameter and hub height), it generates a hybrid mesh conformal with the actuator discs and refined upwind and downstream. Moreover, it presents smooth element size transitions across scales and avoids extending high-resolution areas to all the domain. We take advantage of our automatic and robust mesher to study the mesh convergence of our RANS solver with linear elements, obtaining quadratic mesh convergence for a quantity of interest in all the tested cases. In addition, we quantify the mesh resolution at the terrain surface and at the actuator discs required to achieve a given numerical error in simulations in onshore and offshore frameworks. Finally, we present the generated meshes and the simulation results for an offshore and an onshore wind farm. We analyze in detail one particular wind direction for both cases, and for the onshore wind farm we use our automatic framework to estimate the yearly production of energy and measuring the error against the actual produced one., This work has been partially funded by the EU H2020Energy oriented Center of Excellence (EoCoE) for computer applications, the New European Wind Atlas (NEWA) and the High Performance Computing for Energy (HPC4E) projects. We thank Iberdrola Renovables for their collaboration and for providing wind farm data to validate the developed techniques., Peer Reviewed, Postprint (published version)
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Photocarrier extraction in GaAsSb/GaAsN type-II QW superlattice solar cells

  • Aeberhard, Urs|||0000-0003-2408-8468
  • Gonzalo Martín, Alicia|||0000-0002-8449-388X
  • Ulloa Herrero, José María|||0000-0002-5679-372X